Commit Graph

1994 Commits

Author SHA1 Message Date
Wolfgang Denk 7b43db9211 drivers/mmc/fsl_esdhc.c: fix compiler warnings
Commit 77c1458d caused the following compiler warnings:

fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2010-05-15 19:47:17 +02:00
Kumar Gala f54fe87ace 85xx/fsl-sata: Use is_serdes_configured() to determine if SATA is enabled
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.

Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-12 04:53:51 -05:00
Wolfgang Denk 7b2afd9381 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2010-05-06 23:21:00 +02:00
Ender.Dai 767fdc4af6 drivers/*/Makefile: fix conditional compile rule.
Fix conditional compile rule for twl4030.c and videomodes.c.

Signed-off-by: Ender.Dai <ender.dai@gmail.com>
2010-05-06 00:41:08 +02:00
Graeme Russ 167cdad137 SERIAL: Enable port-mapped access
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06 00:16:28 +02:00
Mike Frysinger b5cebb4fd6 Blackfin: TWI/I2C: implement multibus support
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-05 10:04:38 +02:00
Stefano Babic d205ddcfc5 SPI: added support for MX51 to mxc_spi
This patch add SPI support for the MX51 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic dfe5e14fa2 MX: RTC13783 uses general function to access PMIC
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05 09:48:41 +02:00
Stefano Babic 28bb6d34d3 MX: Added Freescale Power Management Driver
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Wolfgang Denk 679ec15462 Merge branch 'master' of git://git.denx.de/u-boot-net 2010-05-04 22:57:37 +02:00
Mike Frysinger 4324dc72df Blackfin: bfin_mac: hook up new write_hwaddr function
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou 3ac9d6c650 net: ethoc: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou 6c7c444786 net: altera_tse: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Heiko Schocher fb57ec97b9 net: fec_mxc: add write_hwaddr support
tested on the magnesium board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar b5ce63ed12 net:kirkwood_egiga.c: MAC addresses programming using write_hwaddr
Added a new function kwgbe_write_hwaddr for programming egiga
controller's hardware address.
This function will be called for each egiga port being used

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Thomas Chou c960b13ed2 net: add altera triple speeds ethernet mac driver
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Thomas Chou f6569884b4 net: add opencore 10/100 ethernet mac driver
This patch ports the opencore 10/100 ethernet mac driver ethoc.c
from linux kernel to u-boot.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Valentin Yakovenkov bd75db3feb smc911x driver frame alignment patch
SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.

Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.

But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.

It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.

Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.

It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).

Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar f0588fdf92 net: Kirkwood_egiga.c bugfixes for rx path
Cosmetic changes: Few comments updated
Functionality: Rx packet frame size is programming should
be done when port is in disabled state. this is corrected

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Eric Jarrige 2e236bf28e fec_mxc.c: Fix MX27 FEC MAC validity check
Fix MX27 FEC logic to check validity of the MAC address in fuse.
Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change.

Signed-off-by:  Eric Jarrige <jorasse@armadeus.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Andy Fleming 538be58568 tsec: Wait for both RX and TX to stop
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped.  We need to wait for both, or the
controller could get into an invalid state.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Mike Frysinger a45dde2293 net: dm9000x: use standard I/O accessors
The current dm9000x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors.  This can cause problems on
Blackfin systems as the accesses can get out of order.  So convert the
direct volatile dereferences to use the normal in/out macros.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel 5525856d59 mpc512x_fec: Move PHY initialization from probe into init routine.
This saves the autonegotation delay when not using ethernet in U-Boot

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
John Rigby 910119b3c4 fec_mxc don't use internal eeprom on MX25
Avoid using the internal eeprom on MX25 like MX51 already does.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Wolfgang Wegner 33f684d6d5 fix lockup in mcfmii/mii_discover_phy() in case communication fails
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Richard Retanubun 23c34af48f 83xx: UEC: Added support for bitBang MII driver access to PHYs
This patch enabled support for having PHYs on bitBang MII and uec MII
operating at the same time. Modeled after the MPC8360ADS implementation.

Added the ability to specify which ethernet interfaces have bitbang SMI
on the board header file.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel 6f5f89f011 Remove unused "local_crc32" function.
For code archeologists, this is a nice example of copy and paste history.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Prafulla Wadaskar e3f2a93362 net: Kirkwood_egiga.c: fixed build warnings
This patch fixes following build warnings for kirkwood_egiga.c

kirkwood_egiga.c: In function "kwgbe_init":
kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules
kirkwood_egiga.c: In function "kwgbe_recv":
kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:47 -07:00
Stefano Babic 7d27cd08b4 MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Minkyu Kang 3bb6b037e8 SAMSUNG: make s5p common gpio functions
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Minkyu Kang 46a3b5c8df SAMSUNG: serial: modify name from s5pc1xx to s5p
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Stefano Babic 7c8cf0d0c7 MX31: Added LCD support for QONG module
Added support for LCD and splash image to the QONG module.
The supported display is VBEST-VGG322403.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-27 23:13:37 +02:00
Wolfgang Denk c303176aa0 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-04-27 22:57:41 +02:00
Wolfgang Denk c88d6ab19f Merge branch 'next' of git://git.denx.de/u-boot-nios 2010-04-27 22:53:04 +02:00
Dave Liu cd3abcfa2d fsl_sata: Move the snoop bit to another place
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT
is moved to bit28.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:54 -05:00
Dave Liu e4773debb7 fsl_sata: Add the workaround for errata SATA-A001
After power on, the SATA host controller of P1022 Rev1 is configured
in legacy mode instead of the expected enterprise mode.

Software needs to clear bit[28] of HControl register to change to
enterprise mode after bringing the host offline.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:54 -05:00
Thomas Chou 994852966d altera_jtag_uart: bypass when no jtag connection
This patch adds an option to bypass output waiting when there
is no jtag connection. This allows the jtag uart work similar
to a serial uart, ie, boot even without connection.

This option is enabled with CONFIG_ALTERA_JTAG_UART_BYPASS

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-04-24 18:21:23 -04:00
Anatolij Gustschin fbb0030e38 serial: struct serial_device: add uninit() entry for drivers
Subsequent patch extends mpc512x serial driver to support
multiple PSC ports. The driver will provide an uninit()
function to stop the serial controller and to disable the
controller's clock. Adding uninit() entry to struct serial_device
allows disabling the serial controller after usage of
a stdio serial device.

This patch adds uninit() entry to the struct serial_device
and fixes initialization of this structure in the code
accordingly.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 21:34:07 +02:00
Wolfgang Denk 6e5fb4eec3 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2010-04-24 21:25:42 +02:00
Wolfgang Denk b919a3f298 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2010-04-24 21:11:56 +02:00
Dipen Dudhat 77c1458d13 ppc/85xx: PIO Support for FSL eSDHC Controller Driver
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.

Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
2010-04-23 21:02:30 -05:00
Stefan Roese a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Richard Retanubun 26a33504a5 fsl_i2c: Added a callpoint for i2c_board_late_init
This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.
2010-04-19 07:46:35 +02:00
Peter Tyser 1e3827d9cf mips: Move cpu/mips/* to arch/mips/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:25 +02:00
Peter Tyser 8f0fec74ac sh: Move cpu/$CPU to arch/sh/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:17 +02:00
Peter Tyser 8d1f268204 ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:16 +02:00
Peter Tyser 61f2b38a17 Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.

This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:04 +02:00
Albin Tonnerre f852a0c3bf drivers/mtd/spi/eeprom_m95xxx.c: add missing error checking
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2010-04-09 23:05:54 +02:00
Wolfgang Denk 2aa4c57a10 Merge branch 'master' of git://git.denx.de/u-boot-usb 2010-04-09 21:42:18 +02:00
Sergei Shtylyov d7a22a364c EHCI: add NEC PCI ID
Add NEC EHCI controller to the list of the supported devices.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>

 drivers/usb/host/ehci-pci.c |    1 +
 1 file changed, 1 insertion(+)
2010-04-08 21:40:00 +02:00
Sergei Shtylyov c8b2d1dc0f EHCI: fix port reset reporting
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:59 +02:00
Sergei Shtylyov e06a055bcd EHCI: fix off-by-one error in ehci_submit_root()
USB devices on the 2nd port are not detected and I get the following message:

The request port(1) is not configured

That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:59 +02:00
Sergei Shtylyov 6d313c84de EHCI: fix root hub device descriptor
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:58 +02:00
Anatolij Gustschin 760bce07f1 video: ati_radeon_fb.c: fix warning while compiling with DEBUG
Fixes this warning:

ati_radeon_fb.c: In function 'radeon_probe':
ati_radeon_fb.c:598: warning: format '%x' expects type 'unsigned int',
but argument 2 has type 'void *'

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-08 15:59:16 +02:00
Ed Swarthout f6a7a2e888 ati_radeon: Support PCI virtual not eq bus mapping.
Use pci_bus_to_virt() to convert the bus address from the BARs to
virtual address' to eliminate the direct mapping requirement.

Rename variables to better match usage (_phys -> _bus or no-suffix)

This fixes the mpc8572ds CONFIG_PHYS_64BIT mode failure:
"videoboot: Video ROM failed to map!"

Tested on mpc8572ds with and without CONFIG_PHYS_64BIT.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
2010-04-08 15:30:47 +02:00
Ed Swarthout 9624f6d9eb ati_radeon: return with error when emulator fails
Console was being switched to video even if emulator fails and
causing this hang:

               Scanning PCI bus 04
        04  00  1095  3132  0104  00
    PCIE3 on bus 03 - 04
Video: ATI Radeon video card (1002, 5b60) found @(2:0:0)
videoboot: Booting PCI video card bus 2, function 0, device 0
videoboot: Video ROM failed to map!
640x480x8 31kHz 59Hz
radeonfb: FIFO Timeout !

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Tested-by: Anatolij Gustschin <agust@denx.de>
2010-04-08 15:26:29 +02:00
Anatolij Gustschin d5011762f5 video: cfb_console.c: add support for RLE8 bitmaps
Allow displaying 8-bit RLE BMP images.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-08 15:25:43 +02:00
Wolfgang Denk a233631095 Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash 2010-04-08 00:26:03 +02:00
Wolfgang Denk 797131c125 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-04-08 00:23:11 +02:00
Wolfgang Denk 92abce8731 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2010-04-08 00:15:11 +02:00
Wolfgang Denk 6a1f7e54c2 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-04-08 00:06:31 +02:00
Thomas Chou 22d6c8faac cfi_flash: reset timer in flash status check
This patch adds reset_timer() before the flash status check
waiting loop.

Since the timer is basically running asynchronous to the cfi
code, it is possible to call get_timer(0), then only a few
_SYSCLK_ cycles later an interrupt is generated. This causes
timeout even though much less time has elapsed. So the timer
period registers should be reset before get_timer(0) is
called.

There is similar usage in nand_base.c.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-07 11:33:16 +02:00
Kumar Gala 216082754f 85xx: Added various P1012/P1013/P1021/P1022 defines
There are various locations that we have chip specific info:

* Makefile for which ddr code to build
* Added P1012/P1013/P1021/P1022 to cpu_type_list and SVR list
* Added number of LAWs for P1012/P1013/P1021/P1022
* Set CONFIG_MAX_CPUS to 2 for P1021/P1022
* PCI port config

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:21:22 -05:00
Kumar Gala 5a85a30969 ppc/8xxx: Delete PCI nodes from device tree if not configured
If the PCI controller wasn't configured or enabled delete from the
device tree (include its alias).

For the case that we didn't even configure u-boot with knowledge of
the controller we can use the fact that the pci_controller pointer
is NULL to delete the node in the device tree.  We determine that
a controller was not setup (because of HW config) based on the fact
that cfg_addr wasn't setup.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:11:39 -05:00
Roy Zang ab467c512e fsl_esdhc: Only modify the field we are changing in WML
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Jerry Huang 48bb3bb5ac fsl_esdhc: Add function to reset the eSDHC controller
To support multiple block read command we must set abort or use auto
CMD12.  If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Kumar Gala cc4d122658 fsl_esdhc: Always stop clock before changing frequency
We need to stop the clocks on 83xx/85xx as well as imx.  No need to make
this code conditional to just imx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-04-07 00:01:11 -05:00
Stefan Roese d0b0dcaa22 i2c: Move PPC4xx I2C driver into drivers/i2c directory
This patch moves the PPC4xx specific I2C device driver into the I2C
drivers directory. All 4xx config headers are updated to include this
driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-06 08:10:41 +02:00
Matthias Fuchs 0701f730ce at91: use C structs for AT91 OHCI code
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.

It removes one more CONFIG_AT91_LEGACY warning.

at91_pmc.h needs cleanup after migration of the drivers
has been done.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-04-03 15:24:27 -05:00
Achim Ehrlich f936aa0528 Convert at91 watchdog driver to new SoC access
This converts the at91 watchdog driver to new c structure
type to access registers of the SoC

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
2010-04-03 15:24:27 -05:00
Scott McNutt 3ea0037f23 nios2: Fix outx/writex parameter order in io.h
The outx/writex macros were using writex(addr, val) rather than
   the standard writex(val, addr), resulting in incompatibilty with
   architecture independent components. This change set uses standard
   parameter order.

Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-04-02 12:28:41 -04:00
Scott McNutt c9d4f46b5d nios2: Move serial drivers to individual files in drivers/serial
The standard Altera UART & JTAG UART as well as the OpenCores
   YANU driver are now in individual files in drivers/serial
   rather than a single file uner cpu/nios2.

Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-04-02 12:28:40 -04:00
Wolfgang Denk ffa37fc98d Merge branch 'next' 2010-04-01 11:28:32 +02:00
Heiko Schocher b78b48c6a0 net, fec_mxc: only setup the device enetaddr with eeprom value
Only fill the device enetaddr with the contents of the eeprom,
do not program it in MAC address registers

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
2010-03-31 15:13:31 +02:00
Wolfgang Denk 0020db3f0d Merge remote branch 'origin/master' into next 2010-03-29 12:33:43 +02:00
Wolfgang Denk 0d41ad7edc Merge branch 'next' of git://www.denx.de/git/u-boot-cfi-flash into next 2010-03-29 12:33:16 +02:00
Wolfgang Denk be1a91320c Merge branch 'next' of git://git.denx.de/u-boot-coldfire into next 2010-03-28 00:04:18 +01:00
Thomas Chou e5720823f6 cfi flash: add status polling method for amd flash
This patch adds status polling method to offer an alternative to
data toggle method for amd flash chips.

This patch is needed for nios2 cfi flash interface, where the bus
controller performs 4 bytes read cycles for a single byte read
instruction. The data toggle method can not detect chip busy
status correctly. So we have to poll DQ7, which will be inverted
when the chip is busy.

This feature is enabled with the config def,
CONFIG_SYS_CFI_FLASH_STATUS_POLL

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-26 11:35:50 +01:00
Renato Andreola c40c94a3d2 cfi_flash: precision and underflow problem in tout calculation
With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000.

Signed-off-by: Renato Andreola <renato.andreola@imagos.it>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-25 09:44:58 +01:00
TsiChung Liew fa9da59621 ColdFire: Update uart_port_conf in serial driver
Provide proper port passing from serial_init to uart_part_conf.

Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2010-03-24 11:09:08 -05:00
Wolfgang Wegner 89083346d0 add block write function to spartan3 slave serial load
Using seperate function calls for each bit-bang of slave serial
load can be painfully slow. This patch adds the possibility to
supply a block write function that loads the complete block of
data in one call (like it can already be done with Altera FPGAs).
On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load
time from around 15 seconds to around 3 seconds

Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
2010-03-24 11:08:43 -05:00
Nikolay Petukhov 7c27b7b1ea at91: add hwecc method for nand
This is a patch to use the hardware ECC controller of
the AT91SAM9260 for the AT91 nand. Taken from the kernel 2.6.33.

Signed-off-by: Nikolay Petukhov <Nikolay.Petukhov@gmail.com>
2010-03-23 14:29:09 -05:00
Cyril Chemparathy cc41a59a74 TI: Davinci: NAND Driver Cleanup
Modified to use IO accessor routines consistently.  Eliminated volatile usage
to keep checkpatch.pl happy.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
2010-03-23 14:29:09 -05:00
Wolfgang Denk b46b353b90 Merge remote branch 'origin/master' into next 2010-03-21 22:45:36 +01:00
Detlev Zundel fd428c05c8 mpc5xxx: Remove all references to MGT5100
We do not support a processor that never reached a real customer.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2010-03-21 22:44:42 +01:00
Matthias Weisser c0c316569f video: Fix console display when splashscreen is used
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.

Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
2010-03-21 22:44:41 +01:00
Thomas Weber 5647f78d04 mod change 755 => 644 for multiple files
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'

Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-21 22:22:53 +01:00
Stefano Babic 99c006a320 mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessors
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-21 22:22:52 +01:00
Wolfgang Denk 252b404d95 Fix PCI_BASE_ADDRESS_5 handling in pci_hose_config_device()
Signed-off-by: FUJITA Kazutoshi <fujita@soum.co.jp>
Signed-off-by: <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-03-21 17:58:07 +01:00
Matthias Weisser be129aa718 video: Fix console display when splashscreen is used
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.

Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
2010-03-13 16:42:25 +01:00
Wolfgang Denk 93910edb59 Prepare v2010.03-rc1
Coding style cleanup, update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12 23:06:04 +01:00
Detlev Zundel 9c9cbe78dc mpc82xx: Remove SL8245 board and the now orpahned sk98lin network driver.
This code has compile problems and the company does not even exist any
more.  So we take the liberty to drop support for it.

Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
2010-03-12 09:49:23 +01:00
Wolfgang Denk 8c4444ff5e Fix memory leak in mmc_read()
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.

Reported-by: Quentin Armitage <Quentin@Armitage.org.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-11 23:35:43 +01:00
John Rigby 740d6ae5b9 fec_mxc: add MX25 support
Use RMII for MX25
Add code to init gasket that enables RMII

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
2010-03-07 12:36:36 -06:00
John Rigby cb17b92de0 fec_mxc: cleanup and factor out MX27 dependencies
general cleanup
move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c
make MX27 specific phy init conditional on CONFIG_MX27
replace call to imx_get_ahbclk with one to imx_get_fecclk
and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
2010-03-07 12:36:36 -06:00
John Rigby 552ff8f1d9 Add support for Freescale MX25 SOC
ARM926EJS core with MX31 peripherals.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
2010-03-07 12:36:36 -06:00
Stefano Babic c67bee1460 fsl_esdhc: add support for mx51 processor
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic 11fdade294 MMC: add weak function to detect MMC/SD card
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic 250de12bc2 mmc: check correctness of the voltage mask in ocr
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic 71d64c0e4f serial_mxc: add support for MX51 processor
The patch adds support for the Freescale mx51 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
2010-03-07 12:36:35 -06:00
Wolfgang Wegner 8f9a221045 ] fix monitor protection for CONFIG_MONITOR_IS_IN_RAM
For platforms with flash below ram addresses, the current check to
activate monitor protection is wrong/insufficient. This patch fixes
CONFIG_MONITOR_IS_IN_RAM for these systems by adding a check for
this configuration.

Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-04 10:07:12 +01:00
Jens Scharsig 0cf0b93161 convert common files to new SoC access
* add's a warning to all files, which need update to new SoC access
 * convert common files in cpu/../at91 and a lot of drivers to use
   c stucture SoC access

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Jens Scharsig ea8fbba731 add a new AT91 GPIO driver
* add a real AT91 GPIO driver instead of header inline code
* resolve the mixing of port and pins
* change board config files to use new driver
* add macros to gpio to realize backward compatibility

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:54 -06:00
Magnus Lilja eff536befd SPI: Fix 32 bit transfers in mxc_spi.c
Commit f9b6a1575d,  "i.MX31: fix SPI
driver for shorter than 32 bit" broke 32 bit transfers. This patch
makes single 32 bit transfer work again.

Transfer lengths that are known not to work will abort and print
an error message.

Tested on i.MX31 Litekit and i.MX31 PDK using 32 bit transfers to
the MC13783/ATLAS chip (using the 'date' command).

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-02-12 12:31:54 -06:00
Sekhar Nori 8ed5885693 TI DaVinci: Driver for the davinci SPI controller
This adds a driver for the SPI controller found on davinci
based SoCs from Texas Instruments.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-02-12 12:31:53 -06:00
Stefano Babic 4294b2485b fec_mxc: add support for MX51 processor
The patch add support for the Freescale mx51 processor
to the FEC ethernet driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-02-06 22:52:18 -08:00
Siddarth Gore e66b19ce6d NET: kirkwood-egiga smi access fix
Although the datasheet mentions seperate smi registers for each
port, using Port 1 smi register to access ethernet phys does not
work. Hence only Port 0 smi register should be used to access all
devices connected to the smi bus. This behavior is consistant with
the mv643xx driver in the linux kernel.

Signed-off-by: Siddarth Gore <gores@marvell.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-02-06 22:52:14 -08:00
Ladislav Michl a1b322a983 ns16550: kick watchdog while waiting for a character
ns16550 busyloops waiting for incoming byte causing watchdog to reboot
while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc
loop fixes it.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2010-02-03 22:46:58 +01:00
Prathap Srinivas 6e20e64f5c musb: Add host support for DM365 EVM
Add support for musb host on DM365 EVM.

Signed-off-by: Prathap Srinivas <msprathap@ti.com>
2010-02-03 22:06:59 +01:00
Cliff Cai ec2aadb408 usb: musb: fix Blackfin DMA register padding
The conversion from offsets to C structs lost a little padding in the DMA
register map.  Accessing endpoints other than ep0 with DMA would fail as
the addresses wouldn't be adjusted correctly.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-02-03 22:06:59 +01:00
Wolfgang Denk 08254a1a97 Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash 2010-02-03 20:15:46 +01:00
Wolfgang Denk 05c2f4fe29 Merge branch 'master' of git://git.denx.de/u-boot-net 2010-02-03 20:10:20 +01:00
Wolfgang Denk 5c1a1a3069 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2010-02-03 20:05:27 +01:00
Ladislav Michl f3dec798d9 CFI: fix eraseregions numblocks
eraseregions numblocks was sometimes one less than actual, possibly producing
erase regions with zero blocks. As MTD code touches eraseregions only if
numeraseregions is greater that zero, allocate eraseregions only for non
uniform erase size flash.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-02-02 08:22:00 +01:00
Jens Scharsig c041e9d212 new at91_emac network driver (NET_MULTI api)
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at
  MII and RMII interface

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Matthias Kaehlcke 594d57d0cc Add EP93xx ethernet driver
Added ethernet driver for EP93xx SoCs

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Heiko Schocher 582c55a027 83xx, uec: split enet_interface in two variables
There's no sensible reason to unite speed and interface type into
one variable.  So split this variable enet_interface into two
vars: enet_interface_type, which hold the interface type and speed.

Also: add the possibility for switching between 10 and 100 MBit
interfaces on the fly, when running in FAST_ETH mode.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Nick Thompson d7e354374c TI: DaVinci: Updating EMAC driver for DM365, DM646x and DA8XX
The EMAC IP on DM365, DM646x and DA830 is slightly different
from that on DM644x. This change updates the DaVinci EMAC driver
so that EMAC becomes operational on SOCs with EMAC v2.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Semih Hazar 0f751d6ef3 macb: Fix mii_phy_read and mii_phy_write functions
Enabling CONFIG_CMD_MII in AVR32 boards was not possible due to
compile errors.

This patch fixes miiphy_read and miiphy_write functions and
registers them properly.

Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Peter Tyser 5f6b144221 tsec: Add TSEC_FIBER flag
The TSEC_FIBER flag should be set when a PHY is operating with an
external fiber interface.  Currently it is only used to notify a user
that the PHY is operating in fiber mode.

A short description was also added to the other TSEC flag defines so
that it is clear how they differ from one another.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Peter Tyser 8abb8dcc8d tsec: Add support for using the BCM5482 PHY in fiber mode
The BCM5482 PHY supports both copper and fiber as an ethernet medium.
By enabling its copper/fiber mode auto-detection feature it can
dynamically determine if it should be configured for copper or fiber.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Peter Tyser c6dbdfda53 tsec: General cleanup
- Cleanup formatting of phy_info structures

- Fix lines > 80 chars

- Fix some random indentation inconsistencies

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Peter Tyser e1957ef02c tsec: Make functions/data static when possible
This is generally good practice and saves ~150 bytes.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Peter Tyser 27165b5c32 tsec: Clean up Broadcom PHY status parsing
- Remove unnecessary printing "Enet starting in <speed>/<duplex>"
    This same information is already printed during normal ethernet
    operation in the form "Speed: 1000, full duplex".

- Add a check for link before determining link speed and duplex
    If there is no link, speed/duplex don't matter.  This also removes
    the annoying and unneeded "Auto-neg error, defaulting to 10BT/HD"
    message that occurs when no link is detected.

- Whitespace and line > 80 characters cleanup

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Peter Tyser 46e91674fb tsec: Force TBI PHY to 1000Mbps full duplex in SGMII mode
In SGMII mode the link between a processor's internal TBI PHY and an
external PHY should always be 1000Mbps, full duplex.  Also, the SGMII
interface between an internal TBI PHY and external PHY does not
support in-band auto-negotation.

Previously, when configured for SGMII mode a TBI PHY would attempt to
restart auto-negotation during initializtion.  This auto-negotation
between a TBI PHY and external PHY would fail and result in unusable
ethernet operation.

Forcing the TBI PHY and and external PHY to link at 1000Mbps full duplex
in SGMII mode resolves this issue of auto-negotation failing.

Note that 10Mbps and 100Mbps operation is still possible on the external
side of the external PHY even when SGMII is operating at 1000Mbps.
The SGMII interface still operates at 1000Mbps, but each byte of data
is repeated 100 or 10 times for 10/100Mbps and the external PHY handles
converting this data stream into proper 10/100Mbps signalling.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:34 -08:00
Seunghyeon Rhee 76771e595a NET: Fix MAC addr handling for smc911x
This patch turns off MAC address mismatch warning when
optional eeprom programmed with MAC address is not available.
In that case, smc911x's MAC address register has its default
value ff:ff:ff:ff:ff:ff and it's not a valid address. This
makes eth_initialize() show the warning which has no
meaningful information while environment variable ethaddr
overrides the address read from the register. If there's no
eeprom and the value of MAC address register is not valid
after initialization, dev->enetaddr had better not be updated
and maintain its initial value 00:00:00:00:00:00, which I
think is what eth_initialize() expects. This is not a bug fix.
Even without this patch, the driver works fine. It's just for
enhancing the way of displaying messages.

Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:33 -08:00
Matthias Kaehlcke 07c966066b cs8900_initialize() cleanup
cs8900_initialize(): remove unecessary calls to free() and fix memory leak

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:34:33 -08:00
Alessandro Rubini 3e446cbdf3 video: add amba-clcd prime-cell
This adds support for the CLCD logic cell. It accepts precompiled
register values for specific configuration through a board-supplied
data structure.  It is used by the Nomadik nhk8815, added by a later
patch in this series.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2010-01-27 21:23:14 +01:00
John Rigby b081c2e9b9 Nand mxc_nand add v1.1 controller support
Add support for version 1.1 of the nfc nand flash
controller which is on the i.mx25 soc.

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Scott Wood <scottwood@freescale.com>
2010-01-27 14:22:41 -06:00
Wolfgang Denk a84b655fab Merge branch 'master-sync' of git://git.denx.de/u-boot-arm 2010-01-23 17:42:03 +01:00
Vipin KUMAR 62db1c0d79 SPEAr : usbd driver support for SPEAr SoCs
SPEAr SoCs contain a synopsys usb device controller.
USB Device IP can work in 2 modes
- DMA mode
- Slave mode

The driver adds support only for slave mode operation of usb
device IP. This driver is used along with standard USBTTY
driver to obtain a tty interface over USB on the host

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Vipin KUMAR 165fa406ad SPEAr : nand driver support for SPEAr SoCs
SPEAr SoCs contain an FSMC controller which can be used to interface
with a range of memories eg. NAND, SRAM, NOR.
Currently, this driver supports interfacing FSMC with NAND memories

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Vipin KUMAR a6e34f76c5 SPEAr : smi driver support for SPEAr SoCs
SPEAr SoCs contain a serial memory interface controller. This
controller is used to interface with spi based memories.
This patch adds the driver for this IP.

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Vipin KUMAR 2403f8f417 SPEAr : i2c driver support added for SPEAr SoCs
SPEAr SoCs contain a synopsys i2c controller.
This patch adds the driver for this IP.

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Prafulla Wadaskar beca04dd24 Kirkwood: Upgated licencing for files imported from linux source to GPLv2 or later
These are few files directly imported from Linux kernel source.
Those are not modifyed at all ar per strategy.
These files contains source with GPLv2 only
whereas u-boot expects GPLv2 or latter

These files are updated for the same from prior permission from original writes

Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-01-23 08:15:48 -06:00
Felix Radensky 97c9f29008 ppc4xx: Fix sending type 1 PCI transactions
The list of 4xx SoCs that should send type 1 PCI transactions
is not defined correctly. As a result PCI-PCI bridges and devices
behind them are not identified. The following 4xx variants should
send type 1 transactions: 440GX, 440GP, 440SP, 440SPE, 460EX and 460GT.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-01-23 09:27:18 +01:00
Magnus Lilja c4832dffff MXC: Add large page oob layout for i.MX31 NAND controller.
Import the large page oob layout from Linux mxc_nand.c driver.

The CONFIG_SYS_NAND_LARGEPAGE option is used to activate
the large page oob layout. Run time detection is not supported
as this moment.

This has been tested on the i.MX31 PDK board with a large
page NAND device.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-01-19 17:08:13 -06:00
Magnus Lilja f6a9748e32 mxc_nand: Update driver to work with i.MX31.
Tested on i.MX31 Litekit.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-01-19 17:08:13 -06:00
Mike Frysinger fa2744de65 netconsole: mark local funcs with static
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-18 00:21:49 +01:00
Wolfgang Denk 3e3989619f Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2010-01-17 23:08:42 +01:00
Peter Tyser 64917ca389 PCIe, USB: Replace 'end point' references with 'endpoint'
When referring to PCIe and USB 'endpoint' is the standard naming
convention.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-01-17 23:06:44 +01:00
Cliff Cai 581d92eefc Blackfin: bfin_spi: round up clock divider
If the requested clock cannot be exactly obtained, round it up so that we
err on the side of slightly slower rather than slightly faster.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Cliff Cai e54c820991 Blackfin: convert bfin_sdh to generic mmc
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Cliff Cai 17ebd5bf33 Blackfin: bfin_spi: let boards control idle value
Some SPI devices like to see high idle values rather than low.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Wolfgang Denk 2ff6922280 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-01-12 23:47:03 +01:00
Wolfgang Denk f8b365ceb6 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2010-01-12 23:42:32 +01:00
Wolfgang Denk c76b64666e Merge branch 'master' of git://git.denx.de/u-boot-usb 2010-01-12 23:39:08 +01:00
Bryan Wu 321790f61b usb: musb: add virtual root hub control support
For MUSB devices that do not support multipoint (hubs), we have to emulate
a root hub so that we can support core operations like resetting ports.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-12 20:11:27 +01:00
Chris Zhang 5f82887fee Add ppc440epx USB ehci support.
Currently ppc440epx uses OHCI for USB full-speed support. This change adds
support for EHCI.

Signed-off-by: Chris Zhang <chris@seamicro.com>
2010-01-09 10:27:15 +01:00
Chris Zhang b416191a14 Fix EHCI port reset.
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
 controller must terminate the reset and stabilize the state of the port within
 2 milliseconds". Without termination, a port stays at reset state. This is
 observed on ppc4xx(sequoia) boards.

Signed-off-by: Chris Zhang <chris@seamicro.com>
2010-01-09 10:25:43 +01:00
Sanjeev Premi b301be0599 omap3: fix compile warning
This patch fixes this warning during compile:

omap3.c: In function 'musb_platform_init':
omap3.c:126: warning: label 'end' defined but not used

Problem reported by: Dirk Behme[dirk.behme@googlemail.com]

Signed-off-by: Sanjeev Premi <premi@ti.com>
2010-01-09 10:25:09 +01:00
Bryan Wu e608f221c1 usb: musb: add support for Blackfin MUSB
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-01-09 10:25:09 +01:00
Bryan Wu bc72a919e0 usb: musb: change rxcsr register from write to read/modify/write
The RX Control/Status register has bits that we want to preserve, so don't
just write out a single bit.  Preserve the others bits in the process.

The original code posted to the u-boot list had this behavior, but looks
like it was lost somewhere along the way to merging.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-01-09 10:25:09 +01:00
Bryan Wu 8868fd443b usb: musb: make multipoint optional
The multipoint handling under MUSB is optional, and some parts (like the
Blackfin processor) do not implement support for it.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-01-09 10:25:08 +01:00
Bryan Wu df402ba381 usb: musb: make fifo support configurable
The dynamic FIFO handling under MUSB is optional, and some parts (like
the Blackfin processor) do not implement support for it.

Due to this, the FIFO reading/writing steps need special handling, so
mark the common versions weak so drivers can override.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-01-09 10:25:08 +01:00
Mike Frysinger dc2cd05c91 usb: musb: make sure the register layout is packed
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-01-09 10:25:08 +01:00
Ajay Kumar Gupta 7359273d94 DA8xx: Add MUSB host support
Tested USB host functionality on DA830 EVM.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
2010-01-09 10:25:07 +01:00
Nick Thompson 20da6f4d93 Davinci: davinci_nand.c performance enhancments
Introduces various optimisations that approximately triple the
read data rate from NAND when run on da830evm.

Most of these optimisations depend on the endianess of the machine
and most of them are very similar to optimisations already present
in the Linux Kernel.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2010-01-06 16:11:16 -06:00
Kumar Gala ee53650dad ppc/8xxx: Remove is_fsl_pci_agent
All users of is_fsl_pci_agent have been converted to fsl_is_pci_agent
that uses the standard PCI programming model to determine host vs
agent/end-point.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-01-05 13:49:07 -06:00
Sandeep Gopalpet b9e186fc31 NET: Move MDIO regs out of TSEC Space
Moved the mdio regs out of the tsec structure,and
provided different offsets for tsec base and mdio
base so that provision for etsec2.0 can be provided.

This patch helps in providing the support for etsec2.0
In etsec2.0, the MDIO register space and the etsec reg
space are different.

Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into
platform specific files.

Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-01-05 13:49:04 -06:00
Nick Thompson 26be2c53d6 Davinci: NAND enable ECC even when not in NAND boot mode
Davinci: NAND enable ECC even when not in NAND boot mode

On Davinci platforms, the default NAND device is enabled (for ECC)
in low level boot code when NAND boot mode is used. If booting in
another mode, NAND ECC is not enabled. The driver should make
sure ECC is enabled regardless of boot mode if NAND is configured
in U-Boot.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2010-01-04 08:48:17 -06:00
Nick Thompson 97f4eb8cfb Davinci: Configurable NAND chip selects
Davinci: Configurable NAND chip selects

Add a CONFIG_SYS_NAND_CS setting to all davinci configs and
use it to setup the NAND controller in the davinci_nand
mtd driver.

Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
2010-01-04 08:48:17 -06:00
Grazvydas Ignotas ead39d7aa3 TWL4030: make LEDs selectable for twl4030_led_init()
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().

Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2010-01-04 08:48:15 -06:00
Wolfgang Wegner 87d93a1ba2 move prototypes for gunzip() and zunzip() to common.h
Prototype for gunzip/zunzip was only in lib_generic/gunzip.c and thus
repeated in every file using it. This patch moves the prototypes to
common.h and removes all prototypes distributed anywhere else.

Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
2009-12-21 21:39:59 +01:00
Wolfgang Denk f7767c7541 Merge branch 'master' of git://git.denx.de/u-boot-usb 2009-12-21 21:01:56 +01:00
Tom Rix ae4caf2fb5 OMAP3 USB Initialize twl4030 only if required
OMAP3EVM uses ISP1504 phy and so twl4030 related init is not required.

Submitted-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Tom Rix f298e4b6dd OMAP3 Add usb device support
This change adds the usb device support for musb.

Omap3 platform support added at the same level as davinci.

The interface for usbtty to use the musb device support was added.

Verified on omap3 beagle, zoom1 and zoom2.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Tom Rix bffbb2a86d TWL4030 Add usb PHY support
The twl4030 provides a PHY device for connecting a link device,
like musb, to physical connection.

This change adds the twl4030 usb registers and functions for
initializing the PHY as required by omap3.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Tom Rix 8f8bd565f3 USB Consolidate descriptor definitions
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for

usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor

These are out right duplicates in usb.h

usb_device_descriptor
usb_string_descriptor

This one has extra unused elements

usb_endpoint_descriptor

	unsigned char	bRefresh
	unsigned char	bSynchAddress;

These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.

usb_config_descriptor
usb_interface_descriptor

The change is to consolidate the definition of the descriptors
to usbdescriptors.h.  The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.

So

usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface

For these, the common descriptor elements are accessed now
by an element 'desc'.

As an example

-	if (iface->bInterfaceClass != USB_CLASS_HUB)
+	if (iface->desc.bInterfaceClass != USB_CLASS_HUB)

This has been compile tested on MAKEALL arm, ppc and mips.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
Wolfgang Denk b6535daefd Merge branch 'next' of git://git.denx.de/u-boot-net 2009-12-17 22:59:27 +01:00
Kumar Gala d02ffbf8d7 drivers/bios_emulator: Fix compile error in .depend not being generated
make -C drivers/bios_emulator/
make[2]: Entering directory
`drivers/bios_emulator'
In file included from atibios.c:49:
biosemui.h:47:21: error: biosemu.h: No such file or directory
...
x86emu/decode.c:40:28: error: x86emu/x86emui.h: No such file or directory
...

Due to lack of proper CPPFLAGS being passed to .depend generation rule

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-12-17 22:24:36 +01:00
Wolfgang Denk bb3bcfa242 Merge branch 'next' of ../next 2009-12-15 23:38:34 +01:00
Thomas Weber 076cd24cb4 net: dm9000x: fix debug output
commit 60f61e6d76 breaks compile with gcc by introducing __func__
instead of constant string "func" in the macro call but missed to change the macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:57:01 -08:00
John Ogness c179a2896e fec_mxc: incomplete error handling
fec_init() will only allocate fec->base_ptr if it is non-NULL. But
the cleanup routine on error will free the pointer without setting
it to NULL. This means that a later call to fec_init() would result
in using an invalid pointer.

Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:55:15 -08:00
Reinhard Arlt 2ab4a4d095 net: e1000: Add support for the Intel 82546GB controller
This chip is equipped for example on the esd PMC-ETH2-GB board. So let's
add it to the list of supported chips to the e1000 driver.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:52:30 -08:00
Nishanth Menon b7ad4109da NET: LAN91C96 CONFIG_NET_MULTIify
Make the lan91c96 driver capable of CONFIG_NET_MULTI
to be clean for the new arch, add a a lil detect function
Most of the formatting change was done to keep checkpatch
silent, but a few functions and #if 0ed code which
does not make sense for NET_MULTI have been removed

Now, use the lan91c96_initialize() function to init the driver

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-12-13 21:31:26 -08:00
Stefan Roese f4cfe42758 nand: Fix access to last block in NAND devices
Currently, the last block of NAND devices can't be accessed. This patch
fixes this issue by correcting the boundary checking (off-by-one error).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2009-12-11 13:11:57 -06:00
Heiko Schocher 4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Wolfgang Denk 206c00f26f Merge branch 'master' into next
Conflicts:
	lib_generic/zlib.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 22:47:17 +01:00
Daniel Hobi 0ec81db202 Fix computation in nand_util.c:get_len_incl_bad
Depending on offset, flash size and the number of bad blocks,
get_len_incl_bad may return a too small value which may lead to:

1) If there are no bad blocks, nand_{read,write}_skip_bad chooses the
bad block aware read/write code. This may hurt performance, but does
not have any adverse effects.

2) If there are bad blocks, the nand_{read,write}_skip_bad may choose
the bad block unaware read/write code (if len_incl_bad == *length)
which leads to corrupted data.

Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
2009-12-07 22:38:16 +01:00
Mike Rapoport 45b6b65c6b smc911x: fix typo in smc911x_handle_mac_address name
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
2009-12-07 22:04:02 +01:00
Wolfgang Denk 2a49bf3149 Merge branch 'master' into next
Conflicts:
	board/esd/plu405/plu405.c
	drivers/rtc/ftrtc010.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-05 02:11:59 +01:00
Magnus Lilja f3a7bddc06 RTC: Fix return code in MC13783 RTC driver.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2009-12-02 23:29:18 +01:00
Peter Tyser 06015146a1 m41t11: Remove unused functions
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-12-02 23:21:02 +01:00
Vaibhav Hiremath 7c15121f40 omap3_mmc: Encapsulate twl4030 under option CONFIG_TWL4030_POWER
Fixes the build/compilation error if we try to re-use the omap3_mmc code
without TWL4030_POWER.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
2009-11-27 16:26:18 -06:00
Po-Yu Chuang 39ba774f9b arm: A320: driver for FTRTC010 real time clock
This patch adds an FTRTC010 driver for Faraday A320 evaluation board.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2009-11-27 16:26:17 -06:00
kevin.morfitt@fearnside-systems.co.uk ac67804fbb Add a unified s3c24x0 header file
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
Minkyu Kang 9400322609 s5pc1xx: serial: fix the error check logic
Because of Frame error, Parity error and Overrun error are occured only receive
operation, need to masking when error checking.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
Minkyu Kang 47e801bec3 s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xx
This patch moves the s3c64xx header files from include/
to include/asm-arm/arch-s3c64xx

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
kevin.morfitt@fearnside-systems.co.uk 492fb1fdbc Move s3c24x0 header files to asm-arm/arch-s3c24x0/
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.

checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:

ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch

As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.

The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:

WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8	S3C24X0_REG8;
+typedef volatile u16	S3C24X0_REG16;
+typedef volatile u32	S3C24X0_REG32;

I'll fix these errors in another patch.

Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:12 -06:00
Sandeep Paulraj 9829cabbaa Fix for Void function returning value in sbc35-a9g20
Void function was returning 0 in the m41t94 rtc driver.
This makes it similar to m41t62 rtc driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-27 16:26:11 -06:00
Remy Bohmer 41dfd8a603 Add support for CS2 dataflash for Atmel-SPI.
The only missing chipselect line support is CS2, and I need it on
CS2...

Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-11-23 23:43:37 +01:00
Daniel Gorsulowski 4e574c4e2d at91: Extended soft_i2c driver for AT91SAM9263 SoC
While hard_i2c support is not available
(see http://lists.denx.de/pipermail/u-boot/2009-March/049751.html),
this patch enables soft_i2c on AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2009-11-23 09:26:54 +01:00
Mike Frysinger fcffb680e7 sf: fix stmicro offset setup while erasing
Reported-by: Peter Gombos <gombos@protecta.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-11-22 23:56:36 +01:00
Jason McMullan d394a77950 sf: new driver for Winbond W25X16/32/64 devices
Signed-off-by: Jason McMullan <jason.mcmullan@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-11-22 23:54:18 +01:00
Po-Yu Chuang f2cea405f8 Add driver for FTRTC010 real time clock
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>

Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-11-22 22:26:35 +01:00
Wolfgang Denk db6ab438d6 Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into next 2009-11-21 23:17:57 +01:00
Sandeep Paulraj 10a5a79912 NAND: Add Support for 4K page size in DaVinci NAND driver
This patch adds support for NAND devices with a page size of
4K in the DaVinci NAND driver. The layout matches the layout that TI uses
for 4K page size NAND devices in the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-20 13:15:38 -06:00
Hui.Tang 5e1ded558b S3C2410 NAND Flash Add Missing Function
This patch add nand_read_buf() for S3C2410 NAND SPL.
In nand_spl/nand_boot.c, nand_boot() will check nand->select_chip,
so nand->select_chip should also be initialized.

Signed-off-by: Hui.Tang <zetalabs@gmail.com>
2009-11-18 14:30:13 -06:00
Sandeep Paulraj 6cd752f927 NAND: Update read_read_subpage API check
This patch updates a check condition in the NAND driver.
The check condition is similat to what is in linux/next.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-18 14:26:40 -06:00