The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CLCD pads must be configured differently for sleep mode. This patch adds support
for clcd_sleep_pingroup.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some gpio pins are used to control DDR reset and clock enable while the system
is moved into Low power. This patch adds in the corresponding GPIO entries in
the pads_as_gpio_pins to ensure the pads are available as gpio's.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pad direction must also be updated for SPEAr1310, while setting pads values.
This patch adds support for that.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SPEAr1310 has separate PCI and PCIe implementations which are not muxed with
each other. Presently they have been implemented as muxed together with SATA and
are represented wrongly in the software.
In reality only PCIe and SATA implementations are muxed with each other. This
patch separates out pci pins creating a new pingroup and function for pci.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All group names in SPEAr pinctrl have "_grp" at the end of their name. Do the
same for clcd_high_res_grp.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pin entries of rmii and smii are interchanged by mistake. Fix it.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To have pwm on pad no. 34 we also need to select between pwm and SD_LED
functions. Add this to pwm pin mux register configuration.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not all bits of a register are used for pinctrl in SPEAr. So only update bits
relevant to pinctrl using muxreg->mask.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik and Ux500 platforms to use SPARSE_IRQ.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This merges the old <plat/pincfg.h> header into
<linux/platform_data/pinctrl-nomadik.h> and rids us of
yet one more <plat/*> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the platform data header for the Nomadik pin controller
to <linux/platform_data/pinctrl-nomadik.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kp_a_2 pin group was defined but was not declared
as a group of kp function.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In pinctrl-nomadik-db8500.c, add missing definitions that deal
with other alternate-C functions.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This merges the old <plat/pincfg.h> header into
<linux/platform_data/pinctrl-nomadik.h> and rids us of
yet one more <plat/*> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the platform data header for the Nomadik pin controller
to <linux/platform_data/pinctrl-nomadik.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move NMK_GPIO_PER_CHIP to gpio-nomadik.h and define it with a
shift operator.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With DB8500 the number of GPIO chips = number GPIO bank =
number of GPIO ranges.
With DB8540, a new GPIO range configuration is used, some GPIO
banks can have several GPIO ranges.
For example, DB8540 GPIO bank0 (GPIO0 to GPIO32) have 2 GPIO
ranges:
- GPIO0 to GPIO17 : routed
- GPIO18 to GPIO21 : hole
- GPIO22 to GPIO28 : routed
- GPIO29 to GPIO32 : hole
Previously, during nmk_pinctrl_probe(), all GPIO ranges were
parsed, as GPIO ranges are larger than the number of GPIO chips,
a warning occurs. This commit allows each bank to have several
GPIO ranges.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The variable pin is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using for_each_set_bit() to simplify the code.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
/opt/work/linux-2.6/drivers/pinctrl/pinctrl-at91.c: In function 'at91_pinctrl_probe_dt':
/opt/work/linux-2.6/drivers/pinctrl/pinctrl-at91.c:952:12: warning: assignment discards qualifiers from pointer target type
/opt/work/linux-2.6/drivers/pinctrl/pinctrl-at91.c: In function 'at91_gpio_probe':
/opt/work/linux-2.6/drivers/pinctrl/pinctrl-at91.c:1517:17: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we do this
interrupt-parent = <&pioA>;
interrupts = <7 0x0>;
The current core map the irq correctly but the gpio is not configured as input.
The pinctrl configure the pin as gpio with the correct mux parameter but is
not responsible to configure it as input.
So do it during the xlate
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When creating the simple irqdomain, pass the DT node pointer along,
as is apropriate.
Acked-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irqdomain semantics were supposed to be such that a linear
domain would be used if the passed first_irq was zero or
negative, but I got it wrong so only passing zero as first_irq
will work properly. Well, zero is NO_IRQ these days so let's
pass zero. The semantics of irqdomain_add_simple() will be
fixed in a separate patch.
Acked-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Rikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing unlock on the error handle path in function
pinctrl_groups_show().
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since in the DT case, the linear domain path will not allocate
descriptors for the IRQs, we need to use irq_create_mapping()
for mapping hwirqs to Linux IRQs, so these descriptors get
created on-the-fly in this case.
ChangeLog v1->v2:
- Just use irq_create_mapping() in the .to_irq function since
this is called before unmasking or enabling any interrupt
lines, so irq_find_mapping() should be sufficient for the
IRQ handler function.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mutex is locked duplicatly by pinconf_groups_show() and
pin_config_group_get(). It results dead lock. So avoid to lock mutex
in pinconf_groups_show().
Cc: stable@kernel.org
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers require a way to translate GPIO pins to their IRQ numbers.
This patch adds the .to_irq() gpiolib callback to pinctrl-samsung
driver, which creates (if not present yet) and returns an IRQ mapping
for given GPIO pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pins used as wake-up interrupts need to be configured as EINTs. This
patch adds the required configuration code to exynos_wkup_irq_set_type,
to set the pin as EINT when its interrupt trigger type is configured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch reworks wake-up interrupt handling in pinctrl-exynos driver,
so each pin bank, which provides wake-up interrupts, has its own IRQ
domain.
Information about whether given pin bank provides wake-up interrupts,
how many and whether they are separate or muxed are parsed from device
tree.
It gives following advantages:
- interrupts can be specified in device tree in a more readable way,
e.g. :
device {
/* ... */
interrupt-parent = <&gpx2>;
interrupts = <4 0>;
/* ... */
};
- the amount and layout of interrupts is not hardcoded in the code
anymore, but defined in SoC-specific structure
- bank and pin of each wake-up interrupt can be easily identified, to
allow operations, such as setting the pin to EINT function, from
irq_set_type() callback
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the pinctrl-samsung driver to register one GPIO chip
per pin bank, instead of a single chip for all pin banks of the
controller.
It simplifies GPIO accesses a lot (constant time instead of looping
through the list of banks to find the right one) and should have a good
effect on performance of any bit-banging driver.
In addition it allows to reference GPIO pins by a phandle to the bank
node and a local pin offset inside of the bank (similar to previous
gpiolib driver), which is more clear and readable than using indices
relative to the whole pin controller.
Example:
device {
/* ... */
gpios = <&gpk0 4 0>;
/* ... */
};
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of registering one IRQ domain for all pin banks of a pin
controller, this patch implements registration of per-bank domains.
At a cost of a little memory overhead (~2.5KiB for all GPIO interrupts
of Exynos4x12) it simplifies driver code and device tree sources,
because GPIO interrupts can be now specified per banks.
Example:
device {
/* ... */
interrupt-parent = <&gpa1>;
interrupts = <3 0>;
/* ... */
};
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs, like Exynos4x12, have non-sequential layout of EINT control
registers and so current way of calculating register addresses does not
work correctly for them.
This patch adds eint_offset field to samsung_pin_bank struct and
modifies the driver to use it instead of calculating the offsets from
bank index.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It allows one having only
a pointer to particular bank struct to access driver data struct.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It binds banks defined by
internal driver data with bank nodes in device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the loop iterating over all child nodes and parsing
pin groups to check whether the node is really a pin group node by
checking for existence of samsung,pins property.
This is a prerequisite for further patches adding additional subnodes to
the pinctrl node, required for per bank GPIO and interrupt specifiers.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since pin numbers are now assigned dynamically, those are not needed
anymore.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the pinctrl-samsung driver to assign numbers to pins
dynamically instead of static enumerations.
Thanks to this change the amount of code requried to support a SoC can
be greatly reduced and the code made more readable.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pointer to gpio_chip passed to pin_to_reg_bank utility function is
used only to retrieve a pointer to samsung_pinctrl_drv_data structure.
This patch modifies the function and its users to pass a pointer to
samsung_pinctrl_drv_data directly.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the pinctrl-samsung driver to detect when width of a
bit field is set to zero (which means that such configuraton type is not
supported) and return an error instead of trying to modify an inexistent
register.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the simple irqdomain will fall back to a linear domain
if the first_irq provided is <= 0, just use this, just make
sure the first_irq is negative in the device tree case.
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The compilation of the pinctrl driver failed on the legacy
Nomadik NHK8815 platform because it was not providing the PRCMU
interfaces needed to support the extended alternate functions
used by the ux500 series.
Solve this by providing some stubs for the legacy platform, to
avoid too much #ifdefs in the code per se. Theoretically this
actually allows the Nomadik and Ux500 to have a single kernel
image with support for the PRCM registers on the Ux500 (though
they have incompatible archs, but the spirit is there).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The prima2 platform advertises needing no mach/gpio.h header file,
but its pinctrl driver now has a sirfsoc_gpio_set_pull function
that uses constants defined in arch/arm/mach-prima2/include/mach/gpio.h,
which fails to build.
Fortunately, the sirfsoc_gpio_set_pull is not used anywhere in the
kernel, so we can safely remove it. Any out of tree drivers using
it will have to be converted to use proper pinctrl functions to
do the same.
Without this patch, building prima2_defconfig results in:
drivers/pinctrl/pinctrl-sirf.c: In function 'sirfsoc_gpio_set_pull':
drivers/pinctrl/pinctrl-sirf.c:1331:7: error: 'SIRFSOC_GPIO_PULL_NONE' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1331:7: note: each undeclared identifier is reported only once for each function it appears in
drivers/pinctrl/pinctrl-sirf.c:1334:7: error: 'SIRFSOC_GPIO_PULL_UP' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1338:7: error: 'SIRFSOC_GPIO_PULL_DOWN' undeclared (first use in this function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function pinctrl_register() returns
NULL not ERR_PTR(). The PTR_ERR() in the return value
should be replaced with error no.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pointer to "pdev->dev" is already stored in "dev", so use it in
devm_request_and_ioremap().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The samsung pinctrl driver has a probe function that is
__devinit and that calls a lot of other functions that are
marked __init, which kbuild complains about.
Marking everything __devinit means that the code does not
discarded when CONFIG_HOTPLUG is set, which is a little
more wasteful, but also more consistent
Without this patch, building exynos_defconfig results in:
WARNING: drivers/pinctrl/built-in.o(.devinit.text+0x124): Section mismatch in reference from the function samsung_pinctrl_probe() to the function .init.text:samsung_gpiolib_register()
The function __devinit samsung_pinctrl_probe() references
a function __init samsung_gpiolib_register().
If samsung_gpiolib_register is only used by samsung_pinctrl_probe then
annotate samsung_gpiolib_register with a matching annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.
This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This alters the Nomadik pinctrl driver to:
- Call irqdomain_add_linear() for the DT case so we get
all independent from IRQ numbers in this case.
- Call irqdomain_add_simple() for the legacy case, which
allocates the IRQ descriptors for the Nomadik pin controller
dynamically.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upgrade nomadik pinctrl driver to enable selection of other
alternate-C[1-4] functions on some specific ux500 SoC pins.
Handling of those functions is done thanks to PRCM GPIOCR
registers. This was previously managed in PRCMU driver and
it was not really convenient. Idea is to provide a common
way to control all alternate functions.
Note that this improvement does not support the old-fashioned way
used to control nomadik pins, namely the "nmk_config_pin()" function
and its derivatives.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQblIiAAoJEIwa5zzehBx3J1EP/1pxMqjVKQDXxak+A6g8a7r0
hUTjqfiA9nZ4st+nk3PKJL9DNkoTEoZZqXghYRA+N6ej4hAaFJX1izgQDtjtjfRE
s2izZuxGka8Oiic6FpCUoQnMORg10tSLgyvlHNW4hXy3qpe2C4u1D2GJwA/GPeLQ
lHREekcJ3RKWutpG2hMtCT+9Bm4AwnnMY5uO39gxoXeMn6RoaACNIyYxz0NeL5bV
GDuawi7Pc4KJTXX+D/VU0o7VtksiUO8YBczFEra/9khSL/RI2PFalIX3DKiioqvA
yUA11d9proqojIdfdjVRPBHnIMl49H8ohBwbQfKnkNz9msl1BKN5PbakKls97mQ+
vaJpoACnc/3x4P/izEpwry5XqeIl5S5mwz4R4+fojpWpp4JPcly/cAKMAsXf5WRi
NF50E4D/8ysHE8WuBU5YHFgEEbn3nXkRbNMgdYtUwzixdmNJNaU8+33BJo34c4j0
DNktiEdKUBoiiEdsC1MgH86olD/sFNUxvXBub30hhOywoapgQE61fGQGxG38DV/K
kspTHz9SKUrmgbYEyMNOhz4paRrheYxx9cAgKP7Hp7m4Gu8d6ZqRqLqN9hbAbLuW
TbH2FpqcjSw4KnYYCepTixJ3dhGiICiILWHfsW3qCj5Le3YVwedCpBCL1/I+RqEP
kYTToVhur/T1yamHAmBi
=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed. It's an
SoC that's used on some stationary VoIP platforms, and is in desperate
need of some cleanup. Broadcom came back and suggested that we just
deprecate the platform for now, since they aren't going to spend the
resources needed on cleaning it up, and there are no users of the platform
directly from mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO3MAAoJEIwa5zzehBx39VgQAKKjVG+QLQMaDhcZD8bl8xrZ
vDbH5b4kOso34q6D4kXtSb3bA9Anzps6ZZ+dLHBRNHXTXH5FNHTcKNxqhEV1b0qP
3XTZ05/FopixmSKfUvNvx84jM93phGSdXcvz6zcpGgUdNVQ5ElsX5BS3DBSGw12O
K3zVJlQxEQHgT+iXvoFQv5YOREQOzbqrFSm/QORT78+zcm6nPCY5rCJfz1Po05rS
hHTU/JfL5rXgLJaPXqbCkRFitM1CSGQXw8GkSP3IxB5mfDH6DqcWon0Uh3AOh+k2
PXQGNhzHlL6RNesscLDU3YsFhQq1tPL/JA8gzzaTa8z4CCWGTmD48iHUJ0mtXN33
XmglrpNQwiiD9pepWyfN0TPiAD9mBfnRRzwkmmHUkeNeIeVOo+nH+6JWEBc3kjFD
CemIIAtbflC0IZpnaoieOUwO6USukq4CCBdR2icQp9hG9nNnZ1O2L/HeuXn8DxPf
7TksF0wsBAbWkFWRLWmx0dVO0b0fuXsgQ/9+G51OxWOxpMIgMG3BBgkNN6fAybjg
t10jzilu3UKAVyqetWrrmzkzMtHLz6uAlOkR4W0+YoEBG57HD0iepBJZfzqulkb3
i5mdwYUQgPViNsvq9cuIfj/+S8QxRbJ4hT59u7YaAPX5Y3jstHXdjS4nFxv/mH0x
4qzaqYCJxDqdq6CssEKX
=LPF/
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc cleanups, part 2 from Olof Johansson:
"A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed.
It's an SoC that's used on some stationary VoIP platforms, and is in
desperate need of some cleanup. Broadcom came back and suggested that
we just deprecate the platform for now, since they aren't going to
spend the resources needed on cleaning it up, and there are no users
of the platform directly from mainline."
Fix some conflicts due to BCM2835 getting added next to the removed
BCMRING, and removal of tegra files that had been converted to
devicetree.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
ARM: Remove mach-bcmring
ARM: clps711x: Remove board support for CEIVA
ARM: clps711x: Fix register definitions
ARM: clps711x: Fix lowlevel debug-macro
ARM: clps711x: Added simple clock framework
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code was using a homegrown method of looking up the offset
from the irq domain, not to be encouraged. Use the proper
irq_find_mapping() call instead.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch initializes the optional irq_chip pointer gc in sirfsoc
pinctrl_gpio_range.
Signed-off-by: Baohua Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sirfsoc_gpio_set_input() is called in those functions which have
held the spinlock, so delete the duplicated locking.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We always use pinctrl_request_gpio() to get GPIO, If we don't have these
missing pins in the pin list, gpio_request and related operations will fail
for them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'pindesc' was not freed when returning from an error induced
exit path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Jason Cooper:
New drivers:
- pinctrl (dove, kirkwood, mvebu)
- gpio (mvebu)
* 'kirkwood/drivers' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add gpio support in defconfig
arm: mvebu: add DT information for GPIO banks on Armada 370 and XP
arm: mvebu: use GPIO support now that a driver is available
Documentation: add description of DT binding for the gpio-mvebu driver
gpio: introduce gpio-mvebu driver for Marvell SoCs
arm: mvebu: select the pinctrl drivers for Armada 370 and Armada XP platforms
arm: mvebu: split Kconfig options for Armada 370 and XP
ARM: mvebu: adjust Armada XP evaluation board DTS
ARM: mvebu: Add pinctrl support to Armada 370 SoC
ARM: mvebu: Add pinctrl support to Armada XP SoCs
pinctrl: mvebu: add pinctrl driver for Armada XP
pinctrl: mvebu: add pinctrl driver for Armada 370
pinctrl: mvebu: kirkwood pinctrl driver
pinctrl: mvebu: dove pinctrl driver
pinctrl: mvebu: pinctrl driver core
Signed-off-by: Olof Johansson <olof@lixom.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Because of a typo, incorrect field of a structure was being checked.
This patch fixes the check to use correct field.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Although the function is used only a single time, it is not performance
critical and it is pretty heavy, so let the compiler decide whether to
inline it instead.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current way of finding the wakeup-eint node scans the whole device tree
not only children of the pinctrl node, so it might detect a wakeup-eint
node of another pinctrl device.
This patch limits the scope of looking for nodes only to subnodes of the
pinctrl node.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The exynos_irq_demux_eint utility function is used in chained IRQ
handler for EINT16-31 to handle multiplexed interrupts. Inlining it
should improve the performance a bit.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A bit in EINTxx_PEND register is set regardless of interrupt mask, which
causes spurious interrupts. To avoid them, the read value of pending
register must be masked with current interrupt mask manually.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To mask GPIO/wakeup IRQ, the corresponding bit in mask register has to
be set.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pins used as GPIO interrupts need to be configured as EINTs. This patch
adds the required configuration code to exynos_gpio_irq_set_type,
to set the pin as EINT when its interrupt trigger is configured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that Tegra's pinmux is configured solely from device tree, there's
no need for the pinconf types to be defined in arch/arm/mach-tegra/.
Move it into the pinctrl directory to clean up mach-tegra, as a pre-
requisite for single-zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using a temporary buffer, snprintf() and kstrdup(), just
use kasprintf() that does the same thing in just oneline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Colin Cross <ccross@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another possible pin configuration for the MC1 pin group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:
pmx_dummy: pinmux@4a100040 {
compatible = "pinctrl-single";
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x00ff>;
};
&pmx_dummy {
pinctrl-names = "default";
pinctrl-0 = <&board_pins>;
board_pins: pinmux_board_pins {
pinctrl-single,pins = <
0x6c 0xf0f
0x6e 0x10f
0x70 0x23f
0x72 0xa5f
>;
};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add information about the Exynos4210 pin banks and driver data which is
used by the Samsung pinctrl driver. In addition to this, the support for
external gpio and wakeup interrupt support is included and hooked up with
the Samsung pinctrl driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.
This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This makes us possible to define pinmux mapping in board-specific DTS.
prima2.dtsi provides all possible (groups,functions) configuration, and
device in .dts select configurations from dtsi files.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The io-pci series has gained a merge to resolve a nontrivial
conflict.
* cleanup/io-pci:
ARM: Fix ioremap() of address zero
Also includes an update to Linux 3.6-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ux500 machines performs pins (GPIO) reconfiguration when entering
in the suspended mode. This reconfiguration aims at reaching an ultra
low power HW configuration.
Due to this HW reconfiguration, some HW devices can change of HW state
and have their output signals at level that could generate IRQs.
If the non-wakeup IRQs are disabled but not yet masked (delayed interrupt
disable feature from the generic irq layer), effective interrupts reach
the system only because the system attempt to enter the suspended mode.
To prevent such IRQs to trig, all irq chips embedded in ux500 platform
should enable their IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unlike imx6q pinctrl driver that starts nubmering pad from 0, imx5
pinctrl drivers number pad from 1. It causes problem/confusion when
driver accesses imx51_pinctrl_pads array using pin ID as the index.
Change imx51_pads and imx53_pads numbering start from 0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.
Changes since (implicit) v1
- remove references to file names in binding documentation
- remove sed commands from comments in driver
- add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is yet another way to mux the keyboard, so fix up that
group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .conf_reg of MX51_PAD_SD2_CMD__CSPI_MOSI should be 0x7bc rather
than NO_PAD. This error will cause SD2 probe failure.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In function pinctrl_get_locked, pointer p is returned on
error, and also return on no_error.
So, we just return it with no error test.
It's pretty the same in function pinctrl_lookup_state_locked:
state is returned in every case, so we drop the error test
and just return state.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
The irqdomain conversion failed to notice that we do not always
have a DT node to dereference, fix this up by using a simple
dev_err() that also tells the name of the device.
Cc: Loic Pallardy <loic.pallardy@st.com>
Cc: Patrice Chotard <patrice.chotard@stericsson.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the platform-specific COH901 pin control header out of the
ARM tree and down into the proper platform data include
directory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the non-U335 U300 variants are retired from the ARM tree,
also delete the pinctrl driver codepaths for these variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the pointers that are allocated with devm_kzalloc will be automatically freed,
at unload time.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tidy up a small typo in the HSI function group list.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the allocated memory will be destroyed at the driver unload time,
automatically if driver uses the devm_ functions, so no need of
doing devm_kfree at the error path
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not so usual, but there are still some cases which require pinctrl
driver function at arch_initcall time. So register imx23 and imx28
pinctrl driver at postcore_initcall time.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Various cleanups to the U300 driver
- Refactor the pin control core to automatically remove
any GPIO ranges when the drivers are removed, instead of
having the drivers do this explicitly.
- Add a function for registering a batch of GPIO ranges.
- Fix a number of incorrect but non-regressive error checks.
- Incremental improvements to the COH901, i.MX and Nomadik drivers
- Add a one-register-per-pin entirely Device Tree-based pin
control driver from Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=79Wu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"These are the accumulated pin control patches for v3.6:
- Various cleanups to the U300 driver
- Refactor the pin control core to automatically remove any GPIO
ranges when the drivers are removed, instead of having the drivers
do this explicitly.
- Add a function for registering a batch of GPIO ranges.
- Fix a number of incorrect but non-regressive error checks.
- Incremental improvements to the COH901, i.MX and Nomadik drivers
- Add a one-register-per-pin entirely Device Tree-based pin control
driver from Tony Lindgren."
* tag 'pinctrl-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Add one-register-per-pin type device tree based pinctrl driver
pinctrl/nomadik: add spi2_oc1_2 pin group
pinctrl/nomadik: kerneldoc fix
pinctrl/nomadik: use devm_* allocators for gpio probe
pinctrl/nomadik: add pin group to mco function
pinctrl/nomadik: add hsit_a_2 pin group
pinctrl/nomadik: add pin group smcs1 and smps0
pinctrl/nomadik: fix hsir_a_1_pins pin list
pinctrl: pinctrl-imx: fix map setting problem if NO_PAD_CTL is set
pinctrl/coh901: use clk_prepare_[en|dis]able()
pinctrl/pinctrl-tegra: remove IS_ERR checking of pmx->pctl
pinctrl/pinctrl-spear: remove IS_ERR checking of pmx->pctl
pinctrl/u300: drop unused variable
pinctrl: select the proper symbol
pinctrl: add pinctrl_add_gpio_ranges function
pinctrl: remove pinctrl_remove_gpio_range
pinctrl/pinctrl-core: cleanup pinctrl_register
pinctrl/u300: delete pointless debug print
pinctrl/pinctrl-u300: remove devm_kfree at driver unload
We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YodD
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc pincontrol drivers update from Arnd Bergmann:
"We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform."
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: prima2: enable gpiolib unconditionally
PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII
This branch contains two kinds of updates: Some platforms in the process
of getting converted to device tree based booting, and the platform
specific patches necessary for that are included here. Other platforms
are already converted, so we just need to update the actual device
tree source files and the binding documents to add support for new board
and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K3WL
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree description updates from Arnd Bergmann:
"This branch contains two kinds of updates: Some platforms in the
process of getting converted to device tree based booting, and the
platform specific patches necessary for that are included here.
Other platforms are already converted, so we just need to update the
actual device tree source files and the binding documents to add
support for new board and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents."
Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: LPC32xx: Add PWM to base dts file
ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
...
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original pin registers table is derived from u-boot mainline,
but somehow it was found missing some mux functions for USBOTG_ID.
We added it at the bottom by following the exist pin function ids,
then it will not break the exist using of pin function id in dts file.
Reported-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Fix regression for commit 3a86a5f8 (pinctrl: pinctrl-imx: free allocated
pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP)
introduced in 3.5-rc3.
With above commit, the debug code will alway be excuted.
Change to excute it only when DEBUG is defined.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention. This patch ensures the
sleepmode property adheres to the rules.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On 8500 and 9540, all SPI2 pins are driven by SPI block except SPI2_FRM
which is driven as GPIO due to specific constraints.
A new group spi2_oc1_2 is created which exclude SPI2_FRM pin.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO portions of the Nomadik pinctrl driver was not using
the managed devm_* interfaces, lets' use them consequently and
cut down the error path and special case handling.
Acked-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mc0_dat47_a_1 and mc0dat31dir_a_1 groups are missing for mco function
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On 8500 and 9540, all HSI pins are driven by HSI block except
HSIT_ACWAKE0_a which is driven as GPIO due to specific
constraints. A new group hsit_a_2 is created which exclude
HSIT_ACWAKE0_a pin.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add smcs1_b_1_pins as DB8500_PIN_B14 can be SM_CS1 in alt B
Add smps0_c_1_pins as DB8500_PIN_E8 can be SM_PS0 in alt C
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
new_map is allocated according to map_num instead of grp->npins,
if a pin or some pins of a group has NO_PAD_CTL property, the map_num
and the grp->npin are different definitely.
When we set mapping information to the new_map[], we should skip those
pins with NO_PAD_CTL from index, otherwise it is possible the driver
will aceesss to a unallocated region.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The COH901 GPIO driver did not prepare or unprepare its
clock, so let us fix it to do so.
Acked-by: Pankaj Jangra <jangra.pankaj9@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register returns a pointer of struct type struct pinctrl_dev,
if successfully registered to pinctrl subsystem, otherwise returns
NULL, and there wont' be any pointers which are not dereferencible.
They are not type of pointer addresses but are kind of error
codes rather actual addresses, but are a kind of return
codes of functions returning integer types.
return -ENODEV if device registration fails.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register returns a pointer of struct type struct pinctrl_dev,
if successfully registered to pinctrl subsystem, otherwise returns
NULL, and there wont' be any pointers which are not dereferencible.
They are not type of pointer addresses but are kind of error
codes rather actual addresses, but are a kind of return
codes of functions returning integer types.
return -ENODEV if device registration fails.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig entry for the COH901 pin controller depended on
PINMUX_U300 which is stale, use PINCTRL_U300 as it is called
these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Often GPIO ranges are added in batch, so create a special
function for that.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio ranges will be automatically removed when the pinctrl
driver is unregistered.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
lots of places the ret is used just for non zero cases
with out that also we can check the status of the function
calls.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the memory allocated by devm_kzalloc is automatically
freed at the driver detach side, so no neeed of calling
devm_kfree
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In SiRFprimaII, Each GPIO pin can be configured as input or output
independently. If a GPIO is configured as input, it can also be
enabled as an interrupt source (either edge or level triggered).
These pins must be either MUXed as GPIO or other function pads.
Signed-off-by: Yuping Luo <yuping.luo@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This documentation comment existed in an earlier patch set for
GPIO consolidation, so I'm saving it for maintainability of the
code.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 0bf7481 (pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails)
introduced the following build error:
drivers/pinctrl/pinctrl-mxs.c:140:3: error: implicit declaration of function 'free'
Use kfree function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clear the platform data pointer when mxs_pinctrl_probe_dt fails,
and also before the unregistering with pinctrl subsystem.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
if there is no purecfg , the group pointer is allocated using kzalloc and if it
fails to allocate, we wont free the new_map,
if config is true, we call kmemdup and if it
fails to do so we wont free the allocated group if there is no purecfg.
fix this by doing the frees of new_map pointer and group pointers.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After create config map, the new_map pointer becomes point to
PIN_MAP_TYPE_CONFIGS_PIN map rather than PIN_MAP_TYPE_MUX_GROUP map any more.
Thus using new_map pointer to display the MUX_GROUP info is not correct.
Using map pointer instead to show the correct MUX_GROUP map info.
Original the debug message is:
imx6q-pinctrl 20e0000.iomuxc: maps: function Yp group MX6Q_PAD_SD3_CMD num 12
After fix it is:
imx6q-pinctrl 20e0000.iomuxc: maps: function usdhc3 group usdhc3grp-1 num 11
Reported-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_parent can return null if no parent node found, so the allocated new_map
should be freed.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
a) as we allocate the pinctrl_map structure at imx_dt_node_to_map at line 167, anyway
if its an element, or a num_elements * (sizeof(type)) elements allocated to one single
pointer must be freed only once.
CASE. A)
as new_map is not moved and allocated like,
for (i = 0; i < MAX_ELEMS; i++) {
new_map[i] = kmalloc(numelems * size, GFP_KERNEL);
}
its freed as
for (i = 0; i < MAX_ELEMS; i++) {
kfree(new_map[i]);
}
CASE. B)
and its allocated like
new_map = kmalloc(numelems * size, GFP_KERNEL);
it just needs kfree not as case A's.
b) use KERN_DEBUG facility for the IMX_PMX_DUMP macro.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Axel Lin