This change is intended to make the bladeRF source/sink implementations
slightly more resilient to any transient issues in a flow graph.
For poor choices of buffers/transfers or under high CPU load, an RX or
TX operation might time out. Instead of immediately reporting WORK_DONE
and bailing out, an error message is now printed and the device will
attempt to continue transmitting/receiving samples.
After 3 consecutive errors have occurred on an RX/TX operation, the
device will report WORK_DONE; in this situation, something is likely
very wrong.
This avoids inadvertently attempting to use a larger number of transfers
than the underlying USB library/interface allows by specifying a large
value for num_buffers.
Users can specify up to (num_buffers - 1) transfers. However, it is
generally recommended to use half as many transfers as buffers.
following gnuradio commit 39f14138ac9158eb0610e89a2ae1f8290f184c44
This has been removed of Gnuradio iteself in 2012 and this seems to
be causing issues for some OOT on some platforms...
and /etc/gai.conf is not configured to prefer IPv4 hosts.
The current logic handling the output of getaddrinfo() is
flawed in that it only ever attempts to connect() to the
first address returned.
This is a problem for both round-robin and dual-stack hosts.
Furthermore, rtl_tcp_source_c::rtl_tcp_source_c() assumes a colon
in the device string is a port number. This prevents the use
of raw IPv6 addresses. The function will need to be taught how
to handle IPv6 addresses contained within square brackets, e.g.
"rtl_tcp=[2001:db8::1]:1234".
Therefore further work is required to improve the handling of
multiple addresses, and also device strings containing raw IPv6
addresses.
Signed-off-by: Jeremy Visser <jeremy@visser.name>
When size of output buffer was larger than size of input buffer,
uderflow occured because no check on number of avalilable data was done.
This also improves buffer filling for large output buffers, fill output
until anny input is available.
This commit adds support for the bladeRF XB-200 transverter expansion
board. To enable the expansion board and to allow the osmocom source or
sink to tune down to 0Hz, parameter xb200 has to be set. XB-200 comes
with 4 filter banks which can be selected by passing their name as
a value of the xb200 parameter. Automatic filter selection will be
enabled if no value is given to the xb200 parameter.
Example:
osmocom_fft -a bladerf,xb200
osmocom_fft -a bladerf,xb200=50M
The following values are valid:
"custom" : custom band
"50M" : 50MHz band
"144M" : 144MHz band
"222M" : 222MHz band
"auto3db" : Select fiterbank based on -3dB filter points
"auto" : Select filerbank based on -1dB filter points (default)
To alleviate some confusion (described below), the 'loopback' parameter
may now only be applied to a bladeRF source. A warning will be printed
if it is applied to a sink.
This is intended to help users avoid the case where two different
loopback options are applied to the same device. In this case, the
loopback setting on whichever initializes last will be applied. This,
coupled with the fact that not specifying a loopback defaults to
loopback=none, yields rather unintuitive behavior.
Setting the libbladeRF verbosity level needs to be performed prior to
other operations. Otherwise, the desired diagnostic output will not
appear for startup operations (e.g., device opening, enabling loopback).
cpu_format: sc8, sc16, fc32, fc64
otw_format: sc8, sc16
fullscale: specifies the full-scale amplitude when using floats.
peak: specifies a fractional sample level to calculate scaling with the
sc8 wire format.
example:
osmocom_fft -a uhd,otw_format=sc8,fpga=usrp1_fpga_4rx.rbf -s 16M
since dc offset / iq imbalance is not implemented for recent USRPs this
might cause undesired behavior in GRC. As a workaround we do not pass
them to the caller but print them to the stderr.
B210 USRP appears as a 2-channel device by default. We prevent weird
application behavior by restricting the number of connected channels to
the value given via nchan= argument (1 by default).
A couple issues were present in bladerf_common::close, which caused
entries in the _devs list (our "device cache") to not be removed. This
would result in a stale device handle being used upon attempting to
reopen the device.
Two issues were associated with this bug:
- The weak_ptr expired() conditional was incorrect; the logic was
inverted.
- The list item removal and iterator increment was done incorrectly
and would result in a crash after the first item was fixed.
While the RXVGA2 gain can technically go up to 60 dB, the LMS6002D
datasheet recommends it be clamped to 30dB. libbladeRF clamps to a max
of 30dB, so there's no use in setting max to 60 dB here.
The 'verbosity' parameter may be used to increase or suppress output from
libbladeRF. The available log levels are, in order of decreasing
verbosity are:
verbose, debug, info, warning, critical, silent
The 'loopback' parameter may be used to put the bladeRF into one of the
supported loopback modes. The valid modes are listed below. Their
descriptions may be found in the libbladeRF documentation:
bb_txlpf_rxvga2, bb_txlpf_rxlpf bb_txvga1_rxvga2, bb_txvga1_rxlpf
rf_lna1, rf_lna2, rf_lna3
folowing rtl-sdr commit 89f73b183f2dac9c0dd75beca4cf2f77f20c4a36
So far we had 32 * 256KB which was a bit overkill, 15 are more than
enough.
15 was chosen instead of 16 because at least on Linux there seems to be
a system-wide limit of 63 transfers (when they are 256KB large), so 4
dongles can be used on a single machine without lowering the default
transfer number.
Requires https://github.com/airspy/host
Usage example:
osmocom_fft -a airspy
The following named gain stages are available:
LNA: 0 to 15, step 1
MIX: 0 to 15, step 1
IF: 0 to 15, step 1
At the moment the gains are not in dB but gain indices internal to R820t
tuner.
libbladeRF provides accessors for rational sample rates, which the
integer sample rate functions use under the hood. Therefore, there's no
need to check if the requested rate contains a fractional portion and
switch between the two sets of functions.