V3: further refinements:
- use priv member instead of container method
- allow setting of MAC address by write_hwaddr method
- avoid shutting down link between commands
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.
Tested with ./MAKEALL ARM7 that both boards still compile.
Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The correct definition is in drivers/qe/uec.h so just
remove this one.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
We configure the controller but dont have virtual address space thus any
devices on the 4th controller are not accessible in u-boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Make the U-Boot update command sequence conditional. Helps prevent
accidental erasing if an upload or previous step fails
* Make it easier to update other FLASH banks
* Enable DDR controller cache line interleaving and bank cs0/cs1 by default
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original code maps boot flash as non-cacheable region. When calling
relocate_code in flash to copy u-boot from flash to ddr, every loop copy command
is read from flash. The flash read speed will be the bottleneck, which consuming
long time to do this operation. To resovle this, map the boot flash as
write-through cache via tlb. And set tlb to remap the flash after code
executing in ddr, to confirm flash erase operation properly done.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_ENV_SIZE of MPC8569MDS was wrongly set to CONFIG_ENV_SECT_SIZE which
is 128KB, so it took longer time to do crc32 calculation for ENV than it should
do. It causes the bootup for MPC8569MDS significantly slow. This patch fixs it
to 0x2000(8KB), also fix the comment for CONFIG_ENV_SECT_SIZE to correct size.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
uint is typedefed twice if __MACH__ is defined. This generates an error
when calling MAKEALL for netstar bord on OS X.
This patch removes the typedef for __MACH__ case in favor of general
definiton some lines below.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The CCM board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch changes the PPC4xx POST UART driver to use the common
NS16550 functions for receiving and sending. Additionally the
local function for SoC divisor setup are removed. Instead the
functions from arch/powerpc/cpu/ppc4xx/4xx_uart.c are used. This
removes code duplication.
Also the common CONFIG_SYS_NS16550_COMx defines are now used
to describe the POST UART's.
And a compile breakage is fixed, introduced by a git merge of
the ppc4xx/next branch into master. Now "ppc4xx.h" is moved to
"asm/ppc4xx.h". Fixed as well with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch brings the lwmon5 board support up-to-date. Here a
summary of the changes:
lwmon5 board port related:
- GPIO's changed to control the LSB transmitter
- Reset USB PHY's upon power-up
- Enable CAN upon power-up
- USB init error workaround (errata CHIP_6)
- EBC: Enable burstmode and modify the timings for the GDC memory
- EBC: Speed up NOR flash timings
lwmon5 board POST related:
- Add FPGA memory test
- Add GDC memory test
- DSP POST reworked
- SYSMON POST: Fix handling of negative temperatures
- Add output for sysmon1 POST
- HW-watchdog min. time test reworked
Additionally some coding-style changes were done.
Signed-off-by: Sascha Laue <sascha.laue@liebherr.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support code for bluestone board wth APM821XX processor based.
This patch includes early board init, misc init, configure EBC,
initializes UIC, MAKEALL, board.cfg and MAINTAINERS file.
Signed-off-by: Tirumala R Marri <tmarri@apm.com
Signed-off-by: Stefan Roese <sr@denx.de>
Building this board for parallel flash fills up the bss section and thus
fails to link, so bump up the monitor size a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current size used (256KiB) is smaller than the LDR created for
the bf548-ezkit, so 'run update' doesn't work correctly. So bump
up the size a bit by making this flexible per-board config.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We need to use the Blackfin BootROM-specific OOB layout when we boot out
of NAND as that is what the on-chip ROM expects.
Also need to increase the monitor size a little to accommodate the extra
NAND code overhead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We use the lock/unlock options in our default nand code, so enabl
support for the options.
Reported-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The CONFIG_BFIN_CPU option is largely used in the build system, so move
it out of the board config.h and into the board config.mk. It'd be nice
to keep everything in the config.h, but the patch to extract that value
early was rejected.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On the Freescale P1022, the DIU and the LBC share address pins, which means
that when the DIU is active (e.g. the console is on the DVI display), NOR flash
cannot be accessed. So we use the weak accessor function feature of the CFI
flash code to temporarily switch the pin mux from DIU to LBC whenever we want
to read or write flash. This has a significant performance penalty, but it's
the only way to make it work.
This change allows the 'saveenv' command to work when the video display is
enabled. Erasing flash and writing to flash (with the 'cp' command) works,
but reading from flash (with the 'md' and 'cp' commands) does not. Also, while
flash is being written, the video display will be blank.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for the DIU controller. If CONFIG_VIDEO is defined, then
the console will appear on a DVI monitor instead of the serial port.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move common code to the fsl_diu_fb.c file and remove obsolete
code from board files (aria, mpc8610hpcd and pdm360ng).
Move fsl_diu_fb.h file to the include directory.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This change lays the groundwork for the BOOTFLAG_* flags being removed.
This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
included the mpc8308_p1m board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
continuation of commit 39da1ba923d55f316f9f1bb3a960e4ed91dc17ac:
"e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernels"
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch provides support for MPC8308 P1M board with the following
set of features:
Dual UART is supported
NOR flash is supported
Both TSEC Ethernet controllers are supported
PCI Express initialization is supported
Both I2C controllers are supported
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch cleans up the Freescale MPC8308RDB Development board support.
Things fixed:
- Removed unused PCIE2 definitions from configuration
- SICR{L,H} defines used for System I/O Configuration Registers values
instead of hardcoding
- CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of
writing to SCCR from the board code
- sleep mode stuff removed as MPC8308 has no support for deep sleep and
PMCCR1 register. board_early_init_f() removed.
- MPC8308 has no ERRATA for DDR controller so workaround removed
- 'assignment in if statement' issues solved
- use LBLAWAR_* defines instead of hardcoding
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds defines to set supported fields in System I/O
Configuration Registers High and Low on Freescale MPC8308 CPU.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.
On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Remove some unused functionality to make U-Boot build again.
Especially PCI is not used on the board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.
The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.
All PPC4xx board config headers are changed to use this common NS16550
driver now.
Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus
Signed-off-by: Stefan Roese <sr@denx.de>
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
As a part from this cleanup, the GPIO definitions for PPC405EP are
corrected. The high and low parts of the registers (for example
CONFIG_SYS_GPIO0_OSRL vs. CONFIG_SYS_GPIO0_OSRH) have been defined in
the wrong order. This patch now fixes this issue by switching these
xxxH and xxxL values. This brings the GPIO 405EP port in sync with all
other PPC4xx ports.
Signed-off-by: Stefan Roese <sr@denx.de>
Reinhard Meyer