AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Wolfgang Denk