Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the boards config header. This takes advantage of
that for the sbc8540/sbc8560 boards.
There were a couple of cheezy comments pointing at incorrect
files, or files that don't exist, so I've cleaned those up too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CONFIG_SYS_NS16550_CLK too, which was
not real user friendly,
This adds the typical PCI and clock speed make targets to the
toplevel Makefile in accordance with what is being done with
other boards (i.e. using the "-t" to mkconfig).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for "kwbimage" (Kirkwood Boot Image)
image types to the mkimage code.
For details refer to docs/README.kwbimage
This patch is tested with Sheevaplug board
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ron Lee <ron@debian.org>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Commit 65f6f07b added support for the atmel_df_pow2 standalone program
but missed to add a rule to remove it to the "clean" make target.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
P1011 and P2010 are single core variants of P1010 and P2020 respectively.
The board(RDB) will be same.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed same code pieces from cpu/mpc85xx/cpu.c and cpu/mpc86xx/cpu.c
and moved to cpu/mpc8xxx/cpu.c(new file)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move files belonging to the STx boards into common vendor directory and
update the Makefile to reflect this.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the DEKA Research and Development galaxy5200 board
The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Start a common header file for common linker script code (such as
workarounds for older linkers) rather than doing this in the build system.
As fallout, we no longer execute the linker every time config.mk is
included by a build file (which can easily be 70+ times), but rather only
execute it once.
This also fixes a bug in the major version checking by creating a macro to
easily compare versions and keep people from making the same common
mistake (forgetting to check major and minor together).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit f62fb99941 fixed handling of all rodata sections by using a
wildcard combined with calls to ld's builtin functions SORT_BY_ALIGNMENT()
and SORT_BY_NAME(). Unfortunately these functions were only
introduced with biunutils version 2.16, so the modification broke
building with all tool chains using older binutils.
This patch makes it work again. This is done by omitting the use of
these functions for such old tool chains. This will result in
slightly larger target binaries, as the rodata sections are no longer
in optimal order alignment-wise which reauls in unused gaps, but the
effect was found to be insignificant - especially compared to the fact
that you cannot build U-Boot at all in the current state.
As ld seems to have no support for conditionals we run the linker
script through the C preprocessor which can be easily used to remove
the unwanted function calls.
Note that the C preprocessor must be run with the "-ansi" (or a
"-std=") option to make sure all the system-specific predefined
macros outside the reserved namespace are suppressed. Otherise, cpp
might for example substitute "powerpc" to "1", thus corrupting for
example "OUTPUT_ARCH(powerpc)" etc.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Many (especially ARM) tool chains seem to come with broken or
otherwise unusable (for the purposes of builing U-Boot) run-time
support libraries `libgcc.a'. By using the "USE_PRIVATE_LIBGCC"
setting we allow to use alternative libraries instead.
"USE_PRIVATE_LIBGCC" can either be set as an environment variable in
the shell, or as a command line argument when running "make", i. e.
$ make USE_PRIVATE_LIBGCC=yes
or
$ USE_PRIVATE_LIBGCC=yes
$ export USE_PRIVATE_LIBGCC
$ make
The value of "USE_PRIVATE_LIBGCC" is the name of the directory which
contains the alternative run-time support library `libgcc.a'. The
special value "yes" selects the directory $(OBJTREE)/lib_$(ARCH) .
Note that not all architectures provide an alternative `libgcc.a' in
their lib_$(ARCH) directories - so far, only ARM does.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By including autoconf.mk before config.mk, all top level files can use any
config options it sets up (like <arch>_config.mk) or the Makefile itself
without being forced to use lazy evaluation.
The top build system sets up HOSTCFLAGS a bit and exports it, but other
places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the
values stay in sync.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Paul Gortmaker