This change lays the groundwork for the BOOTFLAG_* flags being removed.
This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
included the mpc8308_p1m board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds defines to set supported fields in System I/O
Configuration Registers High and Low on Freescale MPC8308 CPU.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds basic support for Freescale MPC8308 CPU. Serial ports,
NOR flash and integrated Ethernet controllers are supported.
PCI Express is also supported. eSDHC, NAND and USB may work but aren't
tested (using ULPI PHY requires additional patch).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch changed the SICRL_USBDR define to reflect the 4 different bit
settings for this two-bit field. The four different options are '00', '01',
'10', and '11'. This patch also corrects the config file for SIMPC8313 and
MPC8313ERDB for the appropriate fields. This change only affects the MPC8313
cpu.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for MPC83xx PCI-E controllers in Root Complex
mode.
The patch is based on Tony Li and Dave Liu work[1].
Though unlike the original patch, by default we don't register PCI-E
buses for use in U-Boot, we only configure the controllers for future
use in other OSes (Linux). This is done because we don't have enough
of spare BATs to map all the PCI-E regions.
To actually use PCI-E in U-Boot, users should explicitly define
CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES symbol in the board file. And
only then U-Boot will able to access PCI-E, but at the cost of disabled
address translation.
[1] http://lists.denx.de/pipermail/u-boot/2008-January/027630.html
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running a system with 2 or more MPC8349EMDS boards in PCI agent mode,
the boards will lock up the PCI bus by scanning against each other.
The boards lock against each other by trying to access the PCI bus before
clearing their configuration lock bit. Both boards end up in a loop,
sending and receiving "Target Not Ready" messages forever.
When running in PCI agent mode, the scanning now takes place after the
boards have cleared their configuration lock bit.
Also, add a missing declaration to the mpc83xx.h header file, fixing a
build warning.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We'll use these masks to parse TSEC modes out of HRCWH.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fixed typo from CONIFG_MPC837X to CONFIG_MPC837X
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds elements to the 83xx sysconf structure and #define values that are used
by mpc83xx family devices.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Delete the crypto node if not on an E-processor. If on 8360 or 834x family,
check rev and up-rev crypto node (to SEC rev. 2.4 property values)
if on an 'EA' processor, e.g. MPC8349EA.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch moves Freescale Localbus defines out of mpc83xx.h, so we could
use it on MPC85xx and MPC86xx processors.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Current DDR setup easily causes memory corruption, this patch fixes it.
Also fix TIMING_CFG0_MRS_CYC definition.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
The commit 9e89647889
will cause the mpc8315erdb board can't boot up.
The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).
Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com>
Signed-off by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
According to the latest user manual of MPC8315E,
1) The SVCOD of HRCWL is different than 837x
2) The SCCR has changes
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SPCR about TSEC priority is wrong.
Signed-off-by: Michael Barkowski <Michael.Barkowski@freescale.com>
Signed-off-by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC8315E SoC including e300c3 core and new IP blocks,
such as TDM, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The MPC837x SoC including e300c4 core and new IP blocks,
such as SDHC, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the cpu_init_f() function in cpu/mpc83xx/cpu_init.c to program the
bitfields for all 83xx processors. The code to update some bitfields was
compiled only on some processors. Now, the bitfields are programmed as long
as the corresponding CFG_SCCR option is defined in the board header file.
This means that the board header file should not define any CFG_SCCR macros
for bitfields that don't exist on that processor, otherwise the SCCR will be
programmed incorrectly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This change adds 8360 silicon revision 2.1 support to u-boot.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Board code can now request the generic setup code rather than having to
copy-and-paste it for themselves. Boards should be converted to use this
once they're tested with it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
The code that is ifdef'd with CONFIG_MPC8349 is actually applicable to all
MPC834X class processors. Change the protections from CONFIG_MPC8349 to
CONFIG_MPC834X so they are more generic.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For better format and style, I streamlined the 83xx head files,
including immap_83xx.h and mpc83xx.h. In the old head files, 1)
duplicated macro definition appear in the both files; 2) the structure
of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The
macro definition put inside the each structure. So, I cleaned up the
structure of QE immr from immap_83xx.h, deleted the duplicated stuff and
moved the macro definition to mpc83xx.h, Just like MPC8260.
CHANGELOG
*streamline the 83xx immr head file
Signed-off-by: Dave Liu <daveliu@freescale.com>
Incorporated the common unified variable names and the changes in preparation
for releasing mpc8360 patches.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Peter Tyser