Specified the main Oscillator via clock binding.
This will allow to do not hardcode it anymore in the DT board at 12MHz.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
http://www.calao-systems.com/articles.php?lng=en&pg=6099
this daughter board add the following device:
- Micro-SD socket
- TTL 3V3 - (Tx/Rx/RTS/CTS)
- I2C port
- 0.96" Serial OLED Display Module (over UART)
- MP3 decoder with Micro & Speakers
- 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)
for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT
used_led1 will not be re-add via DT as it's used by the motherboard too
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Use i2c-gpio and enable rv3029 RTC.
Enable the rtc in the sam9g20 defconfig.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file is including the SoC specific devices and properties. And
adds the dts file for SMDK5250 board which uses the EXYNOS5250
dts file. Its board specific properites will be added later.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add OMAP mmc related device tree data for OMAP3.
Currenly limited to only omap3-beagle board.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add OMAP mmc related device tree data for OMAP4.
Currenly limited to only omap4-panda and omap4-sdp
boards.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add support for the new smp_twd runtime registration interface
to the imx6q platforms, and remove the old compile-time support.
The imx6q DTS file is updated to match the TWD DT documentation.
Also present in this patch a DTS fix to the timer interrupt routing
(the PPI connection uses bits [15:8]) and trigger (rising edge).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the new smp_twd runtime registration interface
to the highbank platforms, and remove the old compile-time support.
The highbank DTS file is updated to match the TWD DT documentation
and fixes the timer trigger (rising edge).
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pass all the voltage regulator information for
twl6030/twl4030 PMIC from device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add an ethernet SPI chip in the OMAP4 SDP/Blaze board DTS file.
Add a fixed regulator node controlled by a GPIO line to supply
the ethernet chip.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add the 4 McSPI controller nodes present in an OMAP3 device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add the 4 McSPI controller nodes present in an OMAP4 device.
Remove SPI static device initialisation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
* 'dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ARM: OMAP2+: board-generic: Use of_irq_init API
arm/dts: OMAP3: Add interrupt-controller bindings for INTC
ARM: OMAP2/3: intc: Add DT support for TI interrupt controller
* 'dt' of git://github.com/hzhuang1/linux: (6 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
(plus update to v3.3-rc6)
The USB1 port on Tegra2 supports operation in host or device modes. On
Seaboard this is possible, so mark the port as OTG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra's USB1 port supports legacy mode, so mark it as such. Even if we
don't use it, we must turn it off in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add required clock frequencies for the i2c client devices existing
on beagle board.
Add the twl4030 basic description with only the twl_rtc module.
Add the EEPROM node.
Based on original patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55831.html
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Update DTS file with required clock frequencies
for the i2c client devices existing on sdp4430.
Add the twl6030 node inside the i2c1 controller node.
This is the minimal support needed to boot OMAP4 boards
without any crash.
The support for all the features included in this MFD will be
added later.
Add the RTC submodule inside the twl node.
Add tmp105 temperature sensor in i2c3
Add bh1780 Ambient Light Sensor in i2c3
Add hmc5843 3-Axis Digital Compass in i2c4
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Update pandaboard dts file with required clock frequencies
for the i2c client devices existing on pandaboard.
Add the twl6030 node in i2c1 controller.
This is the minimal support needed to boot OMAP4 boards
without any crash.
The support for all the features included in this MFD will be
added later.
Add a generic i2c EEPROM entry.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add a dedicated DTS file for the twl4030/5030 Power + Audio IC.
This chip is a big SoC that will be reused in a lot of various
OMAP3 boards.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add a dedicated DTS file for the twl6030 Power IC.
This chip is a big SoC that will be reused in a lot of various
OMAP4+ boards.
Note: This file is supposed to be included in a board DTS that will
create the twl node in order to allow the &twl reference to work.
Exmaple:
...
&i2c1 {
twl: twl@48 {
reg = <0x48>;
interrupts = <0 7 4>;
interrupt-controller;
interrupt-parent = <&gic>;
};
};
/include/ "twl6030.dtsi"
...
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Very basic support for TeeJet Mt.Ventoux board. Able to boot via
board-generic and ramdisk/initramfs, however most of peripherals are
not supported. Produces tons of twl4030 related errors as this board
doesn't have twl4030 installed.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.
* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: match SoC name not board name in DT board files
ARM: tegra: PCIe: Provide 3.3V supply voltage
ARM: dt: tegra: add the wifi led to paz00 device tree
ARM: dt: tegra: add the power gpio key to paz00 device tree
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected
The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.
For now, only enable UART1/A, and explicitly disable all other ports.
The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.
Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.
While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device tree binding of digital microphone to PAZ00
board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables HW performance measurements, and usage of the "perf" tool.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
devicetree-bindings: Add documentation for i.MX generic boards
ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
ARM i.MX27: Add devicetree support
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the gpio for d7 as we do not support yet the pwm led via dt.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)
Support for those new features are retrieved from the device tree
compatibility string.
Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.
The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.
Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Add support for TI OMAP3 EVM board
arm/dts: OMAP4: Update DTS file with new GIC bindings
arm/dts: OMAP3: Add i2c controller nodes
arm/dts: OMAP4: Add i2c controller nodes
ARM: OMAP2+: Set Kconfig dependencies for PROC_DEVICETREE
arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
ARM: OMAP1: kconfig: Enable IRQ_DOMAIN by default for OMAP1 platforms
ARM: OMAP2+: pm: Do not init statically the SR and voltage layer with DT
ARM: OMAP2+: omap_device: Replace dev_warn by dev_dbg in omap_device_build_from_dt
ARM: OMAP2+: board-generic: Remove un-needed .atag_offset for DT_MACHINE
ARM: OMAP2+: kconfig: Enable devicetree by default for OMAP2+ systems
arm/dts: OMAP: Remove bootargs node from board files
This patch adds basic devicetree support for i.MX27 based SoCs.
Only the bindings for which drivers exist are added here:
- UART
- fec
- CSPI
- I2C
- watchdog
- gpio
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This uart is the primary console for the dreamplug. Removed
kirkwood_uart0_init() call from board-dt.c.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.
After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support. First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.
Driver porting will start with the uart (see next patch), and progress
from there. Possibly, spi/flash/partitions will be next.
When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update the DTS with the proper information required by the
INTC bindings.
- Add the number of interrupt lines
- Add the reg and the compatible entries.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cardhu uses Tegra's SD ports as follows:
SDMMC1: User SD slot, with GPIOs for power, CD, and WP.
SDMMC2: Not used
SDMMC3: WiFi (currently disabled pending future investigation)
SDMMC4: Internal eMMC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add OMAP3 EVM (OMAP3530, AM/DM37x) DTS file to use the omap3.dtsi SoC file,
along with memory node information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The GIC binding was updated in 3.2 and expects 3 interrupt-cells.
- Update the #interrupt-cells
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds Device Tree file for the CoreTile Express A15x2
(V2P-CA15) with Test Chip 1.
As the chip's GIC has 160 interrupt inputs and equivalent SMM
(FPGA) has GIC synthesised with 256 interrupts, NR_IRQS is
increased.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch adds generic Versatile Express DT machine description,
Device Tree description for the motherboard and documentation for
the bindings.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit db0d4db22a ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.
Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds the wifi led bound to the rfkill0 event to the device
tree of paz00.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the wakeup gpio which is connected to the embedded
controller to the device tree of paz00.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the ADT7461 temperature monitoring IC which is connected via
the DVC controller.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
UARTC is connected to the mini-pcie port.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds initial device tree support of ALC5632 sound codec and
machine driver for PAZ00 board. The implementation is based on the WM8903 codec.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.
This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.
On those boards, disable the I2S2 controller since it isn't used.
On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will allow the sound node to refer to the I2S controllers by name
when creating phandles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Adjust the dma-channel property name to match the binding implemented by
the driver. The binding was implemented and documented in a
separate change to the ASoC tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Document binding, and add the node to tegra*.dtsi.
The driver isn't actually instantiated from this node yet, but the I2S
binding will rely on being able to refer to the APB DMA node using a
phandle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra30 GPIO controller has one more bank than Tegra20, and hence
has one more interrupt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
The new content matches tegra20.dtsi, and is < 80 columns.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Device tree include file for the AT91SAM9x5 SoC family.
An additional .dtsi file is created to describe the generic
SAM9x5 CPU Module (CM).
Device tree source files for each Evaluation Kit that are using
the generic CPU Module and the carrier board. The selection of
available peripherals is done in this .dts file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a helper function for finding the index of a string in a string
list property. This helper is useful for bindings that use a separate
*-name property for attaching names to tuples in another property such
as 'reg' or 'gpios'.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P4kO
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUATwtYgGCrR//JCVInAQKzRRAAybELlfOIT1fyVlzkzIgw0/OKxS75Vqda
v5mNYUfQ001WxGjwbFGgFphrQgyhulmLj6gN5l1rwaBjEZlwLe5uk3sReeqeDMLk
bERLbpg22ymka4JVhvugq5qh9UP2ptlvZV/cAZC0u2JBq+CaarFIJsrzbOyXAngf
4kUkaMhKi8DDZTqrwwACaLxR7qtf3ddiSxNLZ93X4fDh4a3qs/EJErVg/xCFlfM3
YTzTjKuqLV2cGT34E9YTJieN9o94G+PiqvbDsP3kOwG2dSElpRWsZwX/0hDoyCxN
cWbqPfrrdzt/kDcNnNd8MZ16AJlPc4ElVVEWPF71tKP3HfKqtZ0vMlpzsldioFz6
8AKvaXJXRkRddY4KqNcXeEQHcDxO0uniG/3lhZY8NlzO/1PnPQ4hGl8fhw+e/2z0
nAQFUsCVIXacsxamPk/fFBUhYzyK7JrnH4pB3b7SPcCj7X9MVyWK+pbT5LA+VGOL
Ys8tv3NtTWEObyW1s3NT+BEy9FkkRu4EG3TxPwHUXk4BTwa6nDmJBPjk7Hv7q4cn
T58lPet8Aylhht2aZx+0dxK3MHtMOmgsJ5jQF0OAi48Kmx8kXPZ1AeXObROncbZL
aI7qfuGTzps7MlUBYlmrMdceTfYLeOqIEoVyFX8N4xLE33alk8DMKc37QoTJVuxQ
KrY8sCVMkK0=
=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hp8k
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-tegra/board-harmony-pcie.c
To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* samsung/dt: (27 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
* tegra/soc:
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
Add initial dts file for EXYNOS4210 SoC. This dts file describes
the SoC specific devices and properties. Along with this, add dts
file for Samsung's SMDKV310 board and Insignal's ORIGEN board which
uses the EXYNOS4210 dts file and extends it to describe the board
specific properties.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This brings all the GPIO key definitions from board-seaboard.c into
tegra-seaboard.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ADT7461 is a temperature monitoring IC. One is present on the DVC
I2C bus on Seaboard.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the device tree to indicate which I2C controller is the DVC
controller. AUXDATA needs to be updated too, since the compatible
value changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the initial device tree for tegra30
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal device tree support for omap2420 and omap2430.
This is needed to keep the uart functional on omap2 after
omap_serial_init is removed from board-generic.c.
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the Cadence macb ethernet controller in at91sam9g45 and at91sam9g20
.dtsi and enable it in at91sam9m10g45ek and usb_a9g20 board device tree file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Sabreauto board was renamed to Armadillo2 recently. To avoid
confusion, rename Sabreauto to Armadillo2/arm2.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1/UART2/... is more readable than UART0/UART1/... .
Remove redundant UART comments.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO1/GPIO2/... is more readable than GPIO0/GPIO1/... .
Remove redundant gpio comments.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since 3.2, the CONFIG_ARM_ATAG_DTB_COMPAT config allows
an old bootloader to still use ATAG to provide cmdline.
Remove chosen/bootargs from the DTS board files.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add some runtime test cases for the library of device tree parsing functions.
v2: - Add testcase for phandle with 0 args
- Don't run testcases if testcase data isn't present in device tree
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert tegra20 IRQ intialization to the GIC devicetree binding. Modify the
interrupt definitions in the dts files according to
Documentation/devicetree/bindings/arm/gic.txt
v3 (swarren):
* Moved of_irq_init() call into board-dt.c to avoid ifdef'ing it.
- Even with a dummy replacement if !CONFIG_OF, the reference from
tegra_dt_irq_match[] to gic_of_init() would still have to be ifdef'd
- It's plausible that tegra_dt_irq_match[] may need to contain more
entries in the future, and defining what they are seems more suitable
for board-dt.c than irq.c
v2 (swarren):
* Removed some stale GIC init code from board-dt.c
* Undid some accidental 0x -> 0x0 search/replace.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[olof: added include of <asm/hardware/gic.h> for compile to pass]
Signed-off-by: Olof Johansson <olof@lixom.net>
Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.
In practice, these controllers:
* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
be attached are not in the device-tree yet. If/when drivers appear, the
SD/MMC port can be re-enabled.
The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.
In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
With board files, all I2C busses run at 400KHz. Fix the device-tree
to be consistent with this. It's possible this is incorrect, but at
least it keeps the board files and device-tree consistent.
Also, disable any I2C controllers that the board files don't register,
also for consistency.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.
In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a dts file for paz00. As a side effect, this also enables
the embedded controller which controls the keyboard, touchpad, power,
leds, and some other functions.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add device-tree file for TrimSlice
* Add that to the list of .dts files to build
* Update board-dt.c to recognize TrimSlice board name
v2: Makefile: Add board-trimslice-pinmux.c to obj-$(CONFIG_MACH_TEGRA_DT).
v3: Makefile: Use brackets not braces around var names
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The I2S and DAS nodes don't have children, and hence don't need to set
address/size cells.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
For now they are a minimal binding. It needs to be amended with
vendor-specific settings for phy setup and link tuning, etc.
v2: Added bindings specification and phy_type properties
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
MAINTAINERS: add ARM/FREESCALE IMX6 entry
arm/imx: merge i.MX3 and i.MX6
arm/imx6q: add suspend/resume support
arm/imx6q: add device tree machine support
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx: add gic_handle_irq function
arm/imx6q: add core definitions and low-level debug uart
arm/imx6q: add device tree source
ARM: highbank: add suspend support
ARM: highbank: Add cpu hotplug support
ARM: highbank: add SMP support
MAINTAINERS: add Calxeda Highbank ARM platform
ARM: add Highbank core platform support
ARM: highbank: add devicetree source
ARM: l2x0: add empty l2x0_of_init
picoxcell: add a definition of VMALLOC_END
picoxcell: remove custom ioremap implementation
picoxcell: add the DTS for the PC7302 board
picoxcell: add the DTS for pc3x2 and pc3x3 devices
...
Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
This adds the devicetree source and documentation for the Calxeda highbank
platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Create a new device tree source file for Atmel at91sam9g45 SoC family.
The Evaluation Kit at91sam9m10g45ek includes it.
This first basic support will be populated as drivers and boards will be
converted to device tree.
Contains serial, dma and interrupt controllers.
The generic board file still takes advantage of platform data for early serial
init. As we need a storage media and the NAND flash driver is not converted to
DT yet, we keep old initialization for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
It adds device tree support for imx51 babbage board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds device tree support for imx53 boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a pinmux node to tegra20.dtsi in order to instantiate the future
pinmux device.
v2: Specify reg property precisely; don't just point at the whole APB_MISC
register range.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add nodes for devices used by PM code (mpu, dsp, iva).
Add a cpus node as well as recommended in the DT spec.
Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.
Add a default bootargs line to allow a boot from RAMDISK.
Add memory node information.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html
Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Add initial device-tree support for OMAP4 SoC.
This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393
Add the generic GIC interrupt-controller from ARM.
Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).
Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
The PC7302 board can be populated with either a PC3X2 or PC3X3 device.
Add DTS files for both variants of the PC7302.
v3: - remove bootargs from dts files
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
This describes the basic hierarchy of picoxcell pc3x3 devices including
clocks and bus interconnect. Some onchip devices are currently omitted
as there haven't been bindings created for them.
v2: - change timer compatible strings to be more soc specific
- split vic node into 2 devices
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
For Seaboard's internal eMMC, this makes the difference between a
5.5MB/s and 10.2MB/s transfer rate. On Harmony, there wasn't any
measurable difference on my cheap/slow ~2MB/s card.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The module is a bridge between the RTC clock domain and the CPU interface
clock domain. ARM access the register of SYSRTC, GPSRTC and PWRC through
this module.
Signed-off-by: Zhiwu Song <zhiwu.song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
gpio controller handles the switch of gpio and pinmux. And drivers/pinctrl/pinmux-sirf.c
will contain both gpio and pinmux.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Adds support for booting via device tree with a simple serial console.
Change-Id: I7f175b8db21928cd13e0fb49f3eed74966a2696f
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For testing the dt work, define a dt-enabled versatile platform.
This patch adds a new versatile platform for when using the device
tree. Add platform and amba devices are discovered and registered by
parsing the device tree. Clocks and initial io mappings are still
configured statically.
This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
SiRFprimaII is the latest generation application processor from CSR’s
Multifunction SoC product family. Designed around an ARM cortex A9 core,
high-speed memory bus, advanced 3D accelerator and full-HD multi-format
video decoder, SiRFprimaII is able to meet the needs of complicated
applications for modern multifunction devices that require heavy concurrent
applications and fluid user experience. Integrated with GPS baseband,
analog and PMU, this new platform is designed to provide a cost effective
solution for Automotive and Consumer markets.
This patch adds the basic support for this SoC and EVB board based on device
tree. It is following the ZYNQ of Xilinx in some degree.
Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Yuping Luo <Yuping.Luo@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Huayi Li <Huayi.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The 1st board support is minimal to get a system up and running
on the Xilinx platform.
This platform reuses the clock implementation from plat-versatile, and
it depends entirely on CONFIG_OF support. There is only one board
support file which obtains all device information from a device tree
dtb file which is passed to the kernel at boot time.
Signed-off-by: John Linn <john.linn@xilinx.com>
Jean-Christophe PLAGNIOL-VILLARD