Right now there's no much code there since the related code is totally
entangled with the LLC one.
This will eventually change in the future when we switch to use
libosmo-gprs.
Hence, this commit is a preparation to have already some place to put
new BSSGP specific code in the future.
Change-Id: I816396ab5ccb86032bbc21b41a959934a7768780
Log an error message and drop the packet instead of asserting if
mm state fsm is in ST_MM_IDLE while the gmm fsm is in
ST_GMM_REGISTERED_NORMAL.
Fixes: OS#5725
Change-Id: I9dab98917c622b36dae22399bb359d747a598208
The gtp_set_cb_recovery3() is similar to gtp_set_cb_recovery2()
with extra parameter representing GSN.
Change-Id: I8b46cf8c52e36b0312eddf37f3e136662b95732e
This reverts commit 4bd931f96d.
The commit was wrong, and previous code is correct.
Relevant specs:
* TS 29.060 7.7.34 Quality of Service (QoS) Profile
* TS 24.008 10.5.6.5 Quality of service
As can be seen in TS 24.008 10.5.6.5, OSMO_IE_GSM_REQ_QOS never comes
with the the ARP byte prepended. This is actually always prepended when
sending the GTP message, as explained in TS 29.060 7.7.34.
As a result, the Qos Service sent in Create PDP Context Request sent to
the GGSN contained wrongly formatted Qos Profile IE, which was observed
checking wireshark with a real phone. This was found due to open5gs-smfd
being more strict about the possible lengths of the IE, since the
wrongly formatted IE send in GTP had length=14, which is incorrect due
to folllowing TS 24.008 10.5.6.5 wording:
"Octets 15-22 are optional. If octet 15 is included, then octet 16 shall also be included, and octets 17-22may be
included."
In this case, due to the wrong format it was seen as including octet 15
but not 16.
Change-Id: I4fc5ab823a27d27482858a7459337a2f8ae593c3
Related: SYS#5793
MMEs connect over Gn interface using GTPCv1 towards the SGSN in order to
exchange RIM PDUs by using "RAN Information Relay" GTPCv1 message type.
For more info, see 3GPP TS 29.060 sec 7.5.14.1 "RAN Information Relay"
In order to support it, this commit does the following:
* Uses new libgtp APIs to rx and tx RAN Information Relay messages. The
same "gsn" object is reused, ie. the local GTPCv1 socket address used
for exchanging messages against GGSN is reused.
* Adds a new "sgsn_mme_ctx" struct holding information about MMEs
allowed by the SGSN, each one containing information about the GTP
address it uses, the in/out routing based on TAI requests, etc. The
set of MMEs and their config can be set up using new VTY node introduced
in this commit.
* The RIM related code in SGSN is refactored to allow forwarding from
and to several types of addresses/interfaces.
Depends: osmo-ggsn.git Change-Id Iea3eb032ccd4aed5187baca7f7719349d76039d4
Depends: libosmocore.git Change-Id I534db7d8bc5ceb19a2a6866f07d5f5c70e456c5c
Related: SYS#5314
Change-Id: I396450b8d8b66595dab8ff7bf41cbf964bb40d93
This function is only expected to be called if the GTP side of the PDP
ctx is still alive, since it will tear down the GTP side and then finish
the pending MS side if needed.
The asserts are added to ease debugging since it was noted that a few
callers were using this function without properly checking the status of
the pdp ctx.
Related: OS#4817
Change-Id: I4248e2e9846fec5ae2c8557384da2deb86668c50
3GPP TS 24.008 Section 10.5.7.2 Radio Priority states that the Radio Priority IE is
3 bits as follows:
--------------------------------------------
0 0 1 priority level 1 (highest)
0 1 0 priority level 2
0 1 1 priority level 3
1 0 0 priority level 4 (lowest)
All other values are interpreted as priority
level 4 by this version of the protocol.
--------------------------------------------
However at least the MediaTek MT6753 and MT6592 have been
observed to interpret a value of 0 0 0 in an undetermined way
resulting in lack of access to RACH in the cell.
Fixes: OS#4506
Change-Id: I810cd541eb5764ee3f2c238bcd3a10836228d0b5
The MS notifies movement to GMM SUSPEND state because it is for instance
handling a call and cannot use PDCH anymore. Once it releases the TCH it
will ASAP move to either dedicated mode or trigger RAU, which means it
will get out of SUSPEND state. So it doesn't make sense to try paging
the MS when in that state.
This change makes test TC_suspend_nopaging pass.
Related: OS#4616
Change-Id: Ia245899eb9f16c7f839785def4ceb721a1c3a11b
New define is available since libosmocore 1.1.0, and we already require
1.2.0, so no need to update dependenices.
Let's change it to avoid people re-using old BSC_FD_* symbols when
copy-pasting somewhere else.
Change-Id: Iaebd049e383b02204a12f39cc6c932a53d25fd72
Since osmo-ggsn.git c94837c6a401bf0f80791b619a9b4cfbe9160afd, those
APIs are a no-op since timers are tracked internally through osmocom
APIs (and at the same time, new implementation fixes some timing related
bugs).
As a result, osmo-sgsn depends now on at least that libgtp commit. Since
it's not yet avaiable on latest libgtp release, let's track it down in
TODO-RELESE to not forget to update libgtp requirements during osmo-sgsn
release.
Related: OS#4178
Change-Id: Ia9a93d4a6ed63cd0c736f9a99d81d730b958d82e
When the MS is in MM_STANDBY, the Routing Area is known,
but not the exact cell.
Start the paging procedure. (Even this is only supported
for the last known cell, not the Routing Area. Routing Area
paging is not yet supported.)
Change-Id: Icc2c6ba70f8f74054546a1e31741fc90b232a23c
State machine inspired in the one from TS 24.008 4.1.3.3.1. Some state
transitions are inroduced in the code but are still commented out since
we lack some functionalitites or improvements in the code to handle
different scenarios.
Most of the logic is still outside of the FSM, but at least now the
states are handled in a sane way triggered by events.
Change-Id: Idecb43c10d66224d4f9ba9320825040ce6cf9a07
Pau Espin
Oliver Smith
Max
Harald Welte
Keith Whyte