mirror of https://gerrit.osmocom.org/simtrace2
introduce support for new ngff_cardem board
This adds support for the new ngff_cardem board, a board that basically combines a ngff breakout board with a built-in SIMtrace2. Cardem works, but depending on the modem it might need a adjusted ATR to ensure a lower baud rate is used by the modem, high rates might lead to weird power cycling of the card after a few transfers. Trace was also tested and appears to work as expected. Change-Id: Ia96124fbe8a752c98e7fd4096d542a3b2b9bc255
This commit is contained in:
parent
51d87fbb66
commit
4fe93be725
|
@ -28,7 +28,8 @@ DEVICE_SIMTRACE = Device(usb_vendor_id=0x1d50, usb_product_id=0x60e3, name="SIMt
|
|||
DEVICE_QMOD = Device(usb_vendor_id=0x1d50, usb_product_id=0x4004, name="sysmoQMOD (Quad Modem)", url={"cardem": "https://ftp.osmocom.org/binaries/simtrace2/firmware/latest/qmod-cardem-dfu-latest.bin"})
|
||||
DEVICE_OWHW = Device(usb_vendor_id=0x1d50, usb_product_id=0x4001, name="OWHW", url={"cardem": "https://ftp.osmocom.org/binaries/simtrace2/firmware/latest/owhw-cardem-dfu-latest.bin"})
|
||||
DEVICE_OCTSIMTEST = Device(usb_vendor_id=0x1d50, usb_product_id=0x616d, name="OCTSIMTEST", url={"cardem": "https://ftp.osmocom.org/binaries/simtrace2/firmware/latest/octsimtest-cardem-dfu-latest.bin"})
|
||||
DEVICES = [DEVICE_SIMTRACE, DEVICE_QMOD, DEVICE_OCTSIMTEST]
|
||||
DEVICE_NGFF_CARDEM = Device(usb_vendor_id=0x1d50, usb_product_id=0x616e, name="ngff-cardem", url={"cardem": "https://ftp.osmocom.org/binaries/simtrace2/firmware/latest/ngff_cardem-cardem-dfu-latest.bin"})
|
||||
DEVICES = [DEVICE_SIMTRACE, DEVICE_QMOD, DEVICE_OCTSIMTEST, DEVICE_NGFF_CARDEM]
|
||||
|
||||
# which firmware does the SIMtrace USN interface subclass correspond
|
||||
FIRMWARE_SUBCLASS = {1: "trace", 2: "cardem"}
|
||||
|
|
|
@ -62,6 +62,7 @@ end
|
|||
function usb_simtrace_protocol.init()
|
||||
local usb_product_dissectors = DissectorTable.get("usb.product")
|
||||
usb_product_dissectors:add(0x1d50616d, usb_simtrace_protocol)
|
||||
usb_product_dissectors:add(0x1d50616e, usb_simtrace_protocol)
|
||||
|
||||
-- DissectorTable.get("usb.bulk"):add(0xffff, usb_simtrace_protocol)
|
||||
end
|
||||
|
|
|
@ -71,8 +71,13 @@ static const conf_func config_func_ptrs[] = {
|
|||
.init = mode_cardemu_init,
|
||||
.exit = mode_cardemu_exit,
|
||||
.run = mode_cardemu_run,
|
||||
#if defined (ngff_cardem)
|
||||
.usart0_irq = mode_cardemu_usart1_irq,
|
||||
.usart1_irq = mode_cardemu_usart0_irq,
|
||||
#else
|
||||
.usart0_irq = mode_cardemu_usart0_irq,
|
||||
.usart1_irq = mode_cardemu_usart1_irq,
|
||||
#endif
|
||||
},
|
||||
#endif
|
||||
#ifdef HAVE_MITM
|
||||
|
|
|
@ -0,0 +1,166 @@
|
|||
/* Osmocom ngff-cardem board definition
|
||||
*
|
||||
* (C) 2021 by Harald Welte <laforge@osmocom.org>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#pragma once
|
||||
#include "board_common.h"
|
||||
#include "simtrace_usb.h"
|
||||
|
||||
/** Name of the board */
|
||||
#define BOARD_NAME "NGFF-CARDEM"
|
||||
/** Board definition */
|
||||
#define ngff_cardem
|
||||
|
||||
/** oscillator used as main clock source (in Hz) */
|
||||
#define BOARD_MAINOSC 12000000
|
||||
/** desired main clock frequency (in Hz, based on BOARD_MAINOSC) */
|
||||
#define BOARD_MCK 58000000 // 12.000 * 29 / 6
|
||||
|
||||
/** MCU pin connected to red LED */
|
||||
#define PIO_LED_RED PIO_PA17
|
||||
/** MCU pin connected to green LED */
|
||||
#define PIO_LED_GREEN PIO_PA18
|
||||
/** red LED pin definition */
|
||||
#define PIN_LED_RED {PIO_LED_RED, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/** green LED pin definition */
|
||||
#define PIN_LED_GREEN {PIO_LED_GREEN, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
/** LEDs pin definition */
|
||||
#define PINS_LEDS PIN_LED_RED, PIN_LED_GREEN
|
||||
/** index for red LED in LEDs pin definition array */
|
||||
#define LED_NUM_RED 0
|
||||
/** index for green LED in LEDs pin definition array */
|
||||
#define LED_NUM_GREEN 1
|
||||
/** the green LED is actually red and used as indication for USIM1 */
|
||||
#define LED_USIM1 LED_GREEN
|
||||
|
||||
/* USIM 2 interface (USART) */
|
||||
#define PIN_USIM2_CLK {PIO_PA2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PIN_USIM2_IO {PIO_PA6, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
#define PINS_ISO7816_USIM2 PIN_USIM2_CLK, PIN_USIM2_IO
|
||||
|
||||
/* USIM 2 interface (TC) */
|
||||
#define PIN_USIM2_IO_TC {PIO_PA1, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PIN_USIM2_CLK_TC {PIO_PA4, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PINS_TC_USIM2 PIN_USIM2_IO_TC, PIN_USIM2_CLK_TC
|
||||
|
||||
/* USIM 1 interface (USART) */
|
||||
#define PIN_USIM1_IO {PIO_PA22, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
#define PIN_USIM1_CLK {PIO_PA23, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
#define PINS_ISO7816_USIM1 PIN_USIM1_CLK, PIN_USIM1_IO
|
||||
|
||||
/* USIM 1 interface (TC) */
|
||||
#define PIN_USIM1_IO_TC {PIO_PA27, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PIN_USIM1_CLK_TC {PIO_PA29, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
#define PINS_TC_USIM1 PIN_USIM1_IO_TC, PIN_USIM1_CLK_TC
|
||||
|
||||
#define PIN_USIM1_nRST {PIO_PA24, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
#define PIN_USIM1_VCC {PIO_PB3, PIOB, ID_PIOB, PIO_INPUT, PIO_DEFAULT}
|
||||
|
||||
#define PIN_USIM2_nRST {PIO_PA7, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT}
|
||||
//#define PIN_USIM2_VCC {PIO_PB2, PIOB, ID_PIOB, PIO_INPUT, PIO_DEFAULT}
|
||||
|
||||
#define PINS_USIM1 PINS_TC_USIM1, PINS_ISO7816_USIM1, PIN_USIM1_nRST
|
||||
#define PINS_USIM2 PINS_TC_USIM2, PINS_ISO7816_USIM2, PIN_USIM2_nRST
|
||||
|
||||
/* from v3 and onwards only (!) */
|
||||
#define PIN_DET_USIM1_PRES {PIO_PA8, PIOA, ID_PIOA, PIO_INPUT, PIO_DEGLITCH | PIO_IT_EDGE}
|
||||
|
||||
/* inputs reading the WWAN LED level */
|
||||
#define PIN_WWAN1 {PIO_PA15, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEGLITCH | PIO_IT_EDGE}
|
||||
#define PINS_WWAN_IN { PIN_WWAN1 }
|
||||
|
||||
#define PIN_MODEM_EN {PIO_PA11, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define PIN_N_MODEM_PWR_ON {PIO_PA26, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
/* outputs controlling RESET input of modems */
|
||||
#define PIN_PERST1 {PIO_PA25, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define PINS_PERST { PIN_PERST1 }
|
||||
|
||||
#define PIN_VERSION_DET {PIO_PA19, PIOA, ID_PIOA, PIO_PERIPH_D, PIO_DEFAULT}
|
||||
|
||||
/* GPIO towards SPDT switches between real SIM and SAM3 */
|
||||
//#define PIN_SIM_SWITCH1 {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
//#define PIN_SIM_SWITCH2 {PIO_PA28, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
#define BOARD_USB_BMATTRIBUTES USBConfigurationDescriptor_SELFPOWERED_NORWAKEUP
|
||||
|
||||
#define BOARD_USB_VENDOR_ID USB_VENDOR_OPENMOKO
|
||||
#define BOARD_USB_PRODUCT_ID USB_PRODUCT_NGFF_CARDEM
|
||||
#define BOARD_DFU_USB_PRODUCT_ID USB_PRODUCT_NGFF_CARDEM
|
||||
#define BOARD_USB_RELEASE 0x010
|
||||
|
||||
#define DETECT_VCC_BY_ADC
|
||||
#define VCC_UV_THRESH_1V8 1500000
|
||||
#define VCC_UV_THRESH_3V VCC_UV_THRESH_1V8
|
||||
|
||||
#ifdef APPLICATION_cardem
|
||||
#define HAVE_CARDEM
|
||||
#define HAVE_BOARD_CARDINSERT
|
||||
struct cardem_inst;
|
||||
void board_set_card_insert(struct cardem_inst *ci, bool card_insert);
|
||||
#endif
|
||||
|
||||
#ifdef APPLICATION_trace
|
||||
#define HAVE_SNIFFER
|
||||
#endif
|
||||
|
||||
/* Card I/O data signal input/output (I/O_SIM in schematic) */
|
||||
#define PIN_SIM_IO {PIO_PA6A_TXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
||||
/* Card CLK clock input (CLK_SIM in schematic) */
|
||||
#define PIN_SIM_CLK {PIO_PA2B_SCK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* Card RST reset signal input (use as input since the phone will drive it) */
|
||||
#define PIN_SIM_RST_SNIFF {PIO_PA7, PIOA, ID_PIOA, PIO_INPUT, PIO_DEGLITCH | PIO_IT_EDGE}
|
||||
/* Pins used to sniff phone-card communication */
|
||||
#define PINS_SIM_SNIFF PIN_SIM_IO, PIN_SIM_CLK, PIN_SIM_RST_SNIFF
|
||||
|
||||
/* Pin to measure card I/O timing (to start measuring the ETU on I/O activity; connected I/O_SIM in schematic) */
|
||||
#define PIN_SIM_IO_INPUT {PIO_PA1B_TIOB0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* Pin used as clock input (to measure the ETU duration; connected to CLK_SIM in schematic) */
|
||||
#define PIN_SIM_CLK_INPUT {PIO_PA4B_TCLK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
|
||||
/* Pins used to measure ETU timing (using timer counter) */
|
||||
#define PINS_TC PIN_SIM_IO_INPUT, PIN_SIM_CLK_INPUT
|
||||
|
||||
//default state: NO uart connected, modem connected to physical sim, NO sim presence override, modem powers sim slot
|
||||
#define pin_conn_usim1_default {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_conn_usim2_default {PIO_PA28, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_conn_mdm_sim_default {PIO_PA0, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_conn_set_sim_det_default {PIO_PA13, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_en_st_sim_vdd_default {PIO_PB2, PIOB, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_en_mdm_sim_vdd_default {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
|
||||
//cardem state: uart2 (!) connected, NO modem connected to physical sim, sim presence override, NOTHING powers sim slot
|
||||
#define pin_conn_usim1_cem {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_conn_usim2_cem {PIO_PA28, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_conn_mdm_sim_cem {PIO_PA0, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_en_st_sim_vdd_cem {PIO_PB2, PIOB, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_en_mdm_sim_vdd_cem {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
//trace state: uart2 (!) connected, modem connected to physical sim, st powers sim slot
|
||||
#define pin_conn_usim1_trace {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_conn_usim2_trace {PIO_PA28, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_conn_mdm_sim_trace {PIO_PA0, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
#define pin_conn_set_sim_det_trace {PIO_PA13, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_en_st_sim_vdd_trace {PIO_PB2, PIOB, ID_PIOB, PIO_OUTPUT_1, PIO_DEFAULT}
|
||||
#define pin_en_mdm_sim_vdd_trace {PIO_PA16, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
#define PIN_MODEM_EN_off {PIO_PA11, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
|
||||
#define PINS_SIM_DEFAULT pin_conn_usim1_default, pin_conn_usim2_default, pin_conn_mdm_sim_default, pin_conn_set_sim_det_default, PIN_N_MODEM_PWR_ON, PIN_MODEM_EN, pin_en_st_sim_vdd_default, pin_en_mdm_sim_vdd_default
|
||||
#define PINS_SIM_CARDEM pin_conn_usim1_cem, pin_conn_usim2_cem, pin_conn_mdm_sim_cem, pin_en_mdm_sim_vdd_cem, pin_en_st_sim_vdd_cem// , pin_conn_set_sim_det_cem
|
||||
|
||||
#define PINS_BUS_SNIFF pin_conn_usim1_trace, pin_conn_usim2_trace, pin_conn_mdm_sim_trace, pin_conn_set_sim_det_trace,PIN_MODEM_EN_off
|
||||
#define PINS_PWR_SNIFF PIN_N_MODEM_PWR_ON, PIN_MODEM_EN, pin_en_st_sim_vdd_trace, pin_en_mdm_sim_vdd_trace
|
|
@ -0,0 +1,22 @@
|
|||
/* card presence utilities
|
||||
*
|
||||
* (C) 2016-2017 by Harald Welte <hwelte@hmw-consulting.de>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
int is_card_present(int port);
|
||||
int card_present_init(void);
|
|
@ -0,0 +1,20 @@
|
|||
/* Code to read/track the status of the WWAN LEDs of attached modems
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
int wwan_led_active(int wwan);
|
||||
int wwan_led_init(void);
|
|
@ -0,0 +1,21 @@
|
|||
/* Code to control the PERST lines of attached modems
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
int wwan_perst_set(int modem_nr, int active);
|
||||
int wwan_perst_do_reset_pulse(int modem_nr, unsigned int duration_ms);
|
||||
int wwan_perst_init(void);
|
|
@ -0,0 +1 @@
|
|||
ngff-cardem
|
|
@ -0,0 +1,159 @@
|
|||
/* sysmocom ngff-cardem application code
|
||||
*
|
||||
* (C) 2021 Harald Welte <laforge@osmocom.org>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#include "board.h"
|
||||
#include "simtrace.h"
|
||||
#include "utils.h"
|
||||
#include "led.h"
|
||||
#include "wwan_led.h"
|
||||
#include "wwan_perst.h"
|
||||
#include "sim_switch.h"
|
||||
#include "boardver_adc.h"
|
||||
#include "card_pres.h"
|
||||
#include <osmocom/core/timer.h>
|
||||
#include "usb_buf.h"
|
||||
|
||||
/* array of generated USB Strings */
|
||||
extern unsigned char *usb_strings[];
|
||||
|
||||
/* returns '1' in case we should break any endless loop */
|
||||
void board_exec_dbg_cmd(int ch)
|
||||
{
|
||||
switch (ch) {
|
||||
case '?':
|
||||
printf("\t?\thelp\n\r");
|
||||
printf("\tR\treset SAM3\n\r");
|
||||
printf("\tl\tswitch off LED 1\n\r");
|
||||
printf("\tL\tswitch on LED 1\n\r");
|
||||
printf("\tg\tswitch off LED 2\n\r");
|
||||
printf("\tG\tswitch on LED 2\n\r");
|
||||
printf("\t1\tGenerate 1ms reset pulse on WWAN1\n\r");
|
||||
printf("\t!\tSwitch Channel A from physical -> remote\n\r");
|
||||
printf("\tt\t(pseudo)talloc report\n\r");
|
||||
break;
|
||||
case 'R':
|
||||
printf("Asking NVIC to reset us\n\r");
|
||||
USBD_Disconnect();
|
||||
NVIC_SystemReset();
|
||||
break;
|
||||
case 'l':
|
||||
led_blink(LED_GREEN, BLINK_ALWAYS_OFF);
|
||||
printf("LED 1 switched off\n\r");
|
||||
break;
|
||||
case 'L':
|
||||
led_blink(LED_GREEN, BLINK_ALWAYS_ON);
|
||||
printf("LED 1 switched on\n\r");
|
||||
break;
|
||||
case 'g':
|
||||
led_blink(LED_RED, BLINK_ALWAYS_OFF);
|
||||
printf("LED 2 switched off\n\r");
|
||||
break;
|
||||
case 'G':
|
||||
led_blink(LED_RED, BLINK_ALWAYS_ON);
|
||||
printf("LED 2 switched on\n\r");
|
||||
break;
|
||||
case '1':
|
||||
printf("Resetting Modem\n\r");
|
||||
wwan_perst_do_reset_pulse(0, 300);
|
||||
break;
|
||||
case '!':
|
||||
sim_switch_use_physical(0, 0);
|
||||
break;
|
||||
case 't':
|
||||
talloc_report(NULL, stdout);
|
||||
break;
|
||||
default:
|
||||
printf("Unknown command '%c'\n\r", ch);
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
void board_main_top(void)
|
||||
{
|
||||
#ifndef APPLICATION_dfu
|
||||
usb_buf_init();
|
||||
|
||||
wwan_led_init();
|
||||
wwan_perst_init();
|
||||
sim_switch_init();
|
||||
#endif
|
||||
|
||||
/* Obtain the circuit board version (currently just prints voltage) */
|
||||
get_board_version_adc();
|
||||
#ifndef APPLICATION_dfu
|
||||
/* Initialize checking for card insert/remove events */
|
||||
card_present_init();
|
||||
#endif
|
||||
wwan_perst_set(0, 0);
|
||||
}
|
||||
|
||||
static int uart_has_loopback_jumper(void)
|
||||
{
|
||||
unsigned int i;
|
||||
const Pin uart_loopback_pins[] = {
|
||||
{PIO_PA9A_URXD0, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT},
|
||||
{PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
|
||||
};
|
||||
|
||||
/* Configure UART pins as I/O */
|
||||
PIO_Configure(uart_loopback_pins, PIO_LISTSIZE(uart_loopback_pins));
|
||||
|
||||
/* Send pattern over UART TX and check if it is received on RX
|
||||
* If the loop doesn't get interrupted, RxD always follows TxD and thus a
|
||||
* loopback jumper has been placed on RxD/TxD, and we will boot
|
||||
* into DFU unconditionally
|
||||
*/
|
||||
int has_loopback_jumper = 1;
|
||||
for (i = 0; i < 10; i++) {
|
||||
/* Set TxD high; abort if RxD doesn't go high either */
|
||||
PIO_Set(&uart_loopback_pins[1]);
|
||||
if (!PIO_Get(&uart_loopback_pins[0])) {
|
||||
has_loopback_jumper = 0;
|
||||
break;
|
||||
}
|
||||
/* Set TxD low, abort if RxD doesn't go low either */
|
||||
PIO_Clear(&uart_loopback_pins[1]);
|
||||
if (PIO_Get(&uart_loopback_pins[0])) {
|
||||
has_loopback_jumper = 0;
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
/* Put pins back to UART mode */
|
||||
const Pin uart_pins[] = {PINS_UART};
|
||||
PIO_Configure(uart_pins, PIO_LISTSIZE(uart_pins));
|
||||
|
||||
return has_loopback_jumper;
|
||||
}
|
||||
|
||||
int board_override_enter_dfu(void)
|
||||
{
|
||||
/* If the loopback jumper is set, we enter DFU mode */
|
||||
if (uart_has_loopback_jumper())
|
||||
return 1;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const Pin deton = {PIO_PA13, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT};
|
||||
static const Pin detoff = {PIO_PA13, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT};
|
||||
|
||||
void board_set_card_insert(struct cardem_inst *ci, bool card_insert)
|
||||
{
|
||||
PIO_Configure(card_insert ? &deton : &detoff, 1);
|
||||
}
|
|
@ -0,0 +1,76 @@
|
|||
/* card presence utilities
|
||||
*
|
||||
* (C) 2016-2021 by Harald Welte <hwelte@hmw-consulting.de>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#include <osmocom/core/timer.h>
|
||||
#include "board.h"
|
||||
#include "utils.h"
|
||||
#include "card_pres.h"
|
||||
|
||||
#define NUM_CARDPRES 1
|
||||
|
||||
#define TIMER_INTERVAL_MS 500
|
||||
|
||||
static const Pin pin_cardpres[NUM_CARDPRES] = { PIN_DET_USIM1_PRES };
|
||||
static int last_state[NUM_CARDPRES] = { -1 };
|
||||
static struct osmo_timer_list cardpres_timer;
|
||||
|
||||
/* Determine if a SIM card is present in the given slot */
|
||||
int is_card_present(int port)
|
||||
{
|
||||
const Pin *pin;
|
||||
int present;
|
||||
|
||||
if (port < 0 || port >= NUM_CARDPRES)
|
||||
return -1;
|
||||
pin = &pin_cardpres[port];
|
||||
|
||||
|
||||
/* high active here */
|
||||
present = PIO_Get(pin);
|
||||
|
||||
return present;
|
||||
}
|
||||
|
||||
static void cardpres_tmr_cb(void *data)
|
||||
{
|
||||
unsigned int i;
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(pin_cardpres); i++) {
|
||||
int state = is_card_present(i);
|
||||
if (state != last_state[i]) {
|
||||
TRACE_INFO("%u: Card Detect Status %d -> %d\r\n", i, last_state[i], state);
|
||||
/* FIXME: report to USB host */
|
||||
last_state[i] = state;
|
||||
}
|
||||
}
|
||||
|
||||
osmo_timer_schedule(&cardpres_timer, 0, TIMER_INTERVAL_MS*1000);
|
||||
}
|
||||
|
||||
int card_present_init(void)
|
||||
{
|
||||
unsigned int i;
|
||||
|
||||
PIO_Configure(pin_cardpres, ARRAY_SIZE(pin_cardpres));
|
||||
|
||||
/* start timer */
|
||||
cardpres_timer.cb = cardpres_tmr_cb;
|
||||
osmo_timer_schedule(&cardpres_timer, 0, TIMER_INTERVAL_MS*1000);
|
||||
|
||||
return 2;
|
||||
}
|
|
@ -0,0 +1,81 @@
|
|||
/* Code to switch between local (physical) and remote (emulated) SIM
|
||||
*
|
||||
* (C) 2015-2017 by Harald Welte <hwelte@hmw-consulting.de>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
#include "board.h"
|
||||
#include "trace.h"
|
||||
#include "led.h"
|
||||
#include "sim_switch.h"
|
||||
|
||||
//uart12bus 2-20e pa20
|
||||
//uart22bus 1-20e pa28
|
||||
//usim2bus 1-10e pa0 pivot
|
||||
//sim det 2-10e pa13
|
||||
|
||||
static const Pin pins_default[] = {PINS_SIM_DEFAULT};
|
||||
static const Pin pins_cem[] = {PINS_SIM_CARDEM};
|
||||
|
||||
static int initialized = 0;
|
||||
|
||||
int sim_switch_use_physical(unsigned int nr, int physical)
|
||||
{
|
||||
const Pin pin = PIN_MODEM_EN;// PIN_N_MODEM_PWR_ON;
|
||||
enum led led;
|
||||
|
||||
if (!initialized) {
|
||||
TRACE_ERROR("Somebody forgot to call sim_switch_init()\r\n");
|
||||
sim_switch_init();
|
||||
}
|
||||
|
||||
TRACE_INFO("Modem %d: %s SIM\n\r", nr,
|
||||
physical ? "physical" : "virtual");
|
||||
|
||||
switch (nr) {
|
||||
case 0:
|
||||
led = LED_USIM1;
|
||||
break;
|
||||
|
||||
default:
|
||||
TRACE_ERROR("Invalid SIM%u\n\r", nr);
|
||||
return -1;
|
||||
}
|
||||
|
||||
if (physical) {
|
||||
TRACE_INFO("%u: Use local/physical SIM\r\n", nr);
|
||||
PIO_Configure(pins_default, PIO_LISTSIZE(pins_default));
|
||||
led_blink(led, BLINK_ALWAYS_ON);
|
||||
} else {
|
||||
TRACE_INFO("%u: Use remote/emulated SIM\r\n", nr);
|
||||
PIO_Configure(pins_cem, PIO_LISTSIZE(pins_cem));
|
||||
led_blink(led, BLINK_ALWAYS_OFF);
|
||||
}
|
||||
|
||||
/* just power cycle the modem because this circumvents weird issues with unreliable signals */
|
||||
PIO_Clear(&pin);
|
||||
mdelay(200);
|
||||
PIO_Set(&pin);
|
||||
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int sim_switch_init(void)
|
||||
{
|
||||
PIO_Configure(pins_default, PIO_LISTSIZE(pins_default));
|
||||
initialized = 1;
|
||||
return 1;
|
||||
}
|
|
@ -0,0 +1,93 @@
|
|||
/* Code to read/track the status of the WWAN LEDs of attached modems
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
/* Depending on the board this is running on, it might be possible
|
||||
* for the controller to read the status of the WWAN LED output lines of
|
||||
* the cellular modem. If the board supports this, it sets the
|
||||
* PIN_WWAN1 and/or PIN_WWAN2 defines in its board.h file.
|
||||
*/
|
||||
#include "board.h"
|
||||
#include "wwan_led.h"
|
||||
|
||||
#ifdef PIN_WWAN1
|
||||
static const Pin pin_wwan1 = PIN_WWAN1;
|
||||
|
||||
static void wwan1_irqhandler(const Pin *pPin)
|
||||
{
|
||||
int active = wwan_led_active(0);
|
||||
|
||||
TRACE_INFO("0: WWAN LED %u\r\n", active);
|
||||
|
||||
/* TODO: notify host via USB */
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef PIN_WWAN2
|
||||
static const Pin pin_wwan2 = PIN_WWAN2;
|
||||
|
||||
static void wwan2_irqhandler(const Pin *pPin)
|
||||
{
|
||||
int active = wwan_led_active(1);
|
||||
TRACE_INFO("1: WWAN LED %u\r\n", active);
|
||||
|
||||
/* TODO: notify host via USB */
|
||||
}
|
||||
#endif
|
||||
|
||||
/* determine if a given WWAN led is currently active or not */
|
||||
int wwan_led_active(int wwan)
|
||||
{
|
||||
const Pin *pin;
|
||||
int active;
|
||||
|
||||
switch (wwan) {
|
||||
#ifdef PIN_WWAN1
|
||||
case 0:
|
||||
pin = &pin_wwan1;
|
||||
break;
|
||||
#endif
|
||||
#ifdef PIN_WWAN2
|
||||
case 1:
|
||||
pin = &pin_wwan2;
|
||||
break;
|
||||
#endif
|
||||
default:
|
||||
return -1;
|
||||
}
|
||||
|
||||
active = PIO_Get(pin) ? 0 : 1;
|
||||
return active;
|
||||
}
|
||||
|
||||
int wwan_led_init(void)
|
||||
{
|
||||
int num_leds = 0;
|
||||
|
||||
#ifdef PIN_WWAN1
|
||||
PIO_Configure(&pin_wwan1, 1);
|
||||
PIO_ConfigureIt(&pin_wwan1, wwan1_irqhandler);
|
||||
PIO_EnableIt(&pin_wwan1);
|
||||
num_leds++;
|
||||
#endif
|
||||
|
||||
#ifdef PIN_WWAN2
|
||||
PIO_Configure(&pin_wwan2, 1);
|
||||
PIO_ConfigureIt(&pin_wwan2, wwan2_irqhandler);
|
||||
PIO_EnableIt(&pin_wwan2);
|
||||
num_leds++;
|
||||
#endif
|
||||
return num_leds;
|
||||
}
|
|
@ -0,0 +1,127 @@
|
|||
/* Code to control the PERST lines of attached modems
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
|
||||
*/
|
||||
/* Depending on the board this is running on, it might be possible
|
||||
* for the controller to set the status of the PERST input line of
|
||||
* the cellular modem. If the board supports this, it sets the
|
||||
* PIN_PERST1 and/or PIN_PERST2 defines in its board.h file.
|
||||
*/
|
||||
#include "board.h"
|
||||
#include "trace.h"
|
||||
#include "wwan_perst.h"
|
||||
#include <osmocom/core/timer.h>
|
||||
|
||||
struct wwan_perst {
|
||||
uint8_t idx;
|
||||
const Pin pin;
|
||||
struct osmo_timer_list timer;
|
||||
};
|
||||
|
||||
#ifdef PIN_PERST1
|
||||
static struct wwan_perst perst1 = {
|
||||
.idx = 0,
|
||||
.pin = PIN_PERST1,
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef PIN_PERST2
|
||||
static struct wwan_perst perst2 = {
|
||||
.idx = 1,
|
||||
.pin = PIN_PERST2,
|
||||
};
|
||||
#endif
|
||||
|
||||
static int initialized = 0;
|
||||
|
||||
static void perst_tmr_cb(void *data)
|
||||
{
|
||||
struct wwan_perst *perst = data;
|
||||
/* release the (low-active) reset */
|
||||
TRACE_INFO("%u: De-asserting modem reset\r\n", perst->idx);
|
||||
PIO_Clear(&perst->pin);
|
||||
}
|
||||
|
||||
static struct wwan_perst *get_perst_for_modem(int modem_nr)
|
||||
{
|
||||
if (!initialized) {
|
||||
TRACE_ERROR("Somebody forgot to call wwan_perst_init()\r\n");
|
||||
wwan_perst_init();
|
||||
}
|
||||
|
||||
switch (modem_nr) {
|
||||
#ifdef PIN_PERST1
|
||||
case 0:
|
||||
return &perst1;
|
||||
#endif
|
||||
#ifdef PIN_PERST2
|
||||
case 1:
|
||||
return &perst2;
|
||||
#endif
|
||||
default:
|
||||
return NULL;
|
||||
}
|
||||
}
|
||||
|
||||
int wwan_perst_do_reset_pulse(int modem_nr, unsigned int duration_ms)
|
||||
{
|
||||
struct wwan_perst *perst = get_perst_for_modem(modem_nr);
|
||||
if (!perst)
|
||||
return -1;
|
||||
|
||||
TRACE_INFO("%u: Asserting modem reset\r\n", modem_nr);
|
||||
PIO_Set(&perst->pin);
|
||||
osmo_timer_schedule(&perst->timer, duration_ms/1000, (duration_ms%1000)*1000);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int wwan_perst_set(int modem_nr, int active)
|
||||
{
|
||||
struct wwan_perst *perst = get_perst_for_modem(modem_nr);
|
||||
if (!perst)
|
||||
return -1;
|
||||
|
||||
osmo_timer_del(&perst->timer);
|
||||
if (active) {
|
||||
TRACE_INFO("%u: Asserting modem reset\r\n", modem_nr);
|
||||
PIO_Set(&perst->pin);
|
||||
} else {
|
||||
TRACE_INFO("%u: De-asserting modem reset\r\n", modem_nr);
|
||||
PIO_Clear(&perst->pin);
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int wwan_perst_init(void)
|
||||
{
|
||||
int num_perst = 0;
|
||||
#ifdef PIN_PERST1
|
||||
PIO_Configure(&perst1.pin, 1);
|
||||
perst1.timer.cb = perst_tmr_cb;
|
||||
perst1.timer.data = (void *) &perst1;
|
||||
num_perst++;
|
||||
#endif
|
||||
|
||||
#ifdef PIN_PERST2
|
||||
PIO_Configure(&perst2.pin, 1);
|
||||
perst2.timer.cb = perst_tmr_cb;
|
||||
perst2.timer.data = (void *) &perst2;
|
||||
num_perst++;
|
||||
#endif
|
||||
initialized = 1;
|
||||
return num_perst;
|
||||
}
|
|
@ -26,6 +26,7 @@
|
|||
#define USB_PRODUCT_SIMTRACE2_DFU 0x60e3 /* was 0x60e2 */
|
||||
#define USB_PRODUCT_SIMTRACE2 0x60e3
|
||||
#define USB_PRODUCT_OCTSIMTEST 0x616d
|
||||
#define USB_PRODUCT_NGFF_CARDEM 0x616e
|
||||
|
||||
/* USB proprietary class */
|
||||
#define USB_CLASS_PROPRIETARY 0xff
|
||||
|
|
|
@ -39,9 +39,21 @@ static const Pin pins_cardsim[] = PINS_CARDSIM;
|
|||
#endif
|
||||
|
||||
/* UART pins */
|
||||
#if defined(ngff_cardem)
|
||||
static const Pin pins_usim1[] = {PINS_USIM2};
|
||||
static const Pin pin_usim1_rst = PIN_USIM2_nRST;
|
||||
#define FIRST_USART_BASE USART0
|
||||
#define FIRST_USART_ID ID_USART0
|
||||
#define FIRST_USART_IRQ USART0_IRQn
|
||||
#else
|
||||
static const Pin pins_usim1[] = {PINS_USIM1};
|
||||
static const Pin pin_usim1_rst = PIN_USIM1_nRST;
|
||||
#define FIRST_USART_BASE USART1
|
||||
#define FIRST_USART_ID ID_USART1
|
||||
#define FIRST_USART_IRQ USART1_IRQn
|
||||
#endif
|
||||
static const Pin pin_usim1_vcc = PIN_USIM1_VCC;
|
||||
|
||||
#ifdef PIN_USIM1_IO_DIR
|
||||
static const Pin pin_io_dir = PIN_USIM1_IO_DIR;
|
||||
#endif
|
||||
|
@ -85,8 +97,8 @@ struct cardem_inst cardem_inst[] = {
|
|||
{
|
||||
.num = 0,
|
||||
.usart_info = {
|
||||
.base = USART1,
|
||||
.id = ID_USART1,
|
||||
.base = FIRST_USART_BASE,
|
||||
.id = FIRST_USART_ID,
|
||||
.state = USART_RCV
|
||||
},
|
||||
.ep_out = SIMTRACE_CARDEM_USB_EP_USIM1_DATAOUT,
|
||||
|
@ -569,7 +581,7 @@ void mode_cardemu_init(void)
|
|||
|
||||
/* configure USART as ISO-7816 slave (e.g. card) */
|
||||
ISO7816_Init(&cardem_inst[0].usart_info, CLK_SLAVE);
|
||||
NVIC_EnableIRQ(USART1_IRQn);
|
||||
NVIC_EnableIRQ(FIRST_USART_IRQ);
|
||||
PIO_ConfigureIt(&pin_usim1_rst, usim1_rst_irqhandler);
|
||||
PIO_EnableIt(&pin_usim1_rst);
|
||||
|
||||
|
@ -627,9 +639,9 @@ void mode_cardemu_exit(void)
|
|||
PIO_DisableIt(&pin_usim1_rst);
|
||||
PIO_DisableIt(&pin_usim1_vcc);
|
||||
|
||||
NVIC_DisableIRQ(USART1_IRQn);
|
||||
USART_SetTransmitterEnabled(USART1, 0);
|
||||
USART_SetReceiverEnabled(USART1, 0);
|
||||
NVIC_DisableIRQ(FIRST_USART_IRQ);
|
||||
USART_SetTransmitterEnabled(FIRST_USART_BASE, 0);
|
||||
USART_SetReceiverEnabled(FIRST_USART_BASE, 0);
|
||||
|
||||
#ifdef CARDEMU_SECOND_UART
|
||||
PIO_DisableIt(&pin_usim2_rst);
|
||||
|
|
|
@ -18,6 +18,8 @@ ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="4003", GROUP="plugdev"
|
|||
ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="4004", GROUP="plugdev"
|
||||
# sysmocom OCTSIMTEST
|
||||
ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="616d", GROUP="plugdev"
|
||||
# ngff-cardem
|
||||
ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="616e", GROUP="plugdev"
|
||||
|
||||
# All done
|
||||
LABEL="simtrace2_rules_end"
|
||||
|
|
|
@ -33,5 +33,6 @@ const struct dev_id osmo_st2_compatible_dev_ids[] = {
|
|||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_QMOD_SAM3 },
|
||||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_SIMTRACE2 },
|
||||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_OCTSIMTEST },
|
||||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_NGFF_CARDEM },
|
||||
{ 0, 0 }
|
||||
};
|
||||
|
|
|
@ -315,6 +315,7 @@ static const struct option opts[] = {
|
|||
/* Known USB device with SIMtrace firmware supporting sniffer */
|
||||
static const struct dev_id compatible_dev_ids[] = {
|
||||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_SIMTRACE2 },
|
||||
{ USB_VENDOR_OPENMOKO, USB_PRODUCT_NGFF_CARDEM },
|
||||
{ 0, 0 }
|
||||
};
|
||||
|
||||
|
|
Loading…
Reference in New Issue