rtl8169 does not have write_hwaddr function.
However, eth stuff executes write_hwaddr function
because eth_device structure has not been initialized.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The size of the other bank needed to be added to the br0 setting;
this got dropped in the LBC cleanup.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Display the 64-byte Reset Configuration Word (RCW) during boot, so that
there's no confusion as to what RCW U-boot is using.
Reset Configuration Word (RCW):
00000000: 4a500000 00000000 18181818 00008888
00000010: 28402400 00002000 fe800000 01200000
00000020: 00000000 00000000 00000000 000b0000
00000030: 00000000 00000000 00000000 00000000
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We appear to have different refclk's on the different corenet DS boards
so move the define out of the common header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_TEXT_BASE setting is common across the 'corenet_ds' board
family so move it out of P4080DS.h and into corenet_ds.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SQW/INT pin in RTC can be used for generating square wave(by default) or
as interrupt line. U-boot is registering this pin for interrupts.
Configuring SQW/INT bit as interrupt line during board initialization
to avoid spurious interrupts generated by square wave.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce a SPL specific CONFIG_SYS_TEXT_BASE_SPL define to be used by
the linker. This has similiar semantics to CONFIG_SYS_TEXT_BASE however
since SPL is a unqiue image we introduce a new variable to control its
text base address.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_MONITOR_BASE instead of CONFIG_SYS_TEXT_BASE in early
init code so we can share the same code with NAND or NOR boot and not
have additional ifdefs in here.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix u-boot-nand.lds and u-boot-nand_spl.lds according to:
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Wed Sep 29 14:05:56 2010 -0500
commit fbe53f59bd
85xx: Use gc-sections to reduce image size
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When P2020DS DDR2 was merged it was merged incorrectly and propogated to
boards.cfg. Fix this by moving DDR2 config to be associated with
P2020DS and not P1_P2_RDB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Supports most types that support Read-Id and the FM25H20.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().
With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
If start of any DRAM bank is greater than total DDR size, remaining DDR banks' start address & size were left un-initialized in dram_init function. This could break other functions who uses array 'gd->bd->bi_dram'. Kirkwood network driver is one example. This also stops Linux kernel from booting.
v2 - Set start address also to 0. Without this Linux kernel couldn't
boot up
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
After moving the definition of CONFIG_SYS_TEXT_BASE to the respective
board config files, all Marvell kirkwood board have just a single and
common entry in their config.mk files:
KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
Replace the only reference to KWD_CONFIG in the top level Makefile by
an equivalent setting, and remove all kirkwood config.mk files.
Signed-off-by: Wolfgang Denk <wd at denx.de>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Siddarth Gore <gores at marvell.com>
Cc: Simon Kagstrom <simon.kagstrom at netinsight.net>
Cc: Heiko Schocher <hs at denx.de>
Cc: Eric Cooper <ecc at cmu.edu>
Acked-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Current default options increase u-boot size to overlap the location of the environment in NAND, move environment higher up
Signed-off-by: Gray Remlin <g_remlin@rocketmail.com>
This patch is to fix build breakage and support new relocation
scheme for mx51evk.
- Correct IRAM base address and add size definition
The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than
0x1FFE8000 which is for older revision.
- Include imx-regs.h in mx51evk.h
Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be
referred to.
- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
They are used to define init RAM layout.
- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been
buried by Wolfgang's commit below
25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
This patch is to consolidate default mx51evk env for two primary
boot modes, mmcboot and netboot.
It also cleans some unused env like netdev, uboot and redundant
env like loadaddr since CONFIG_LOADADDR already defines it.
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
The mx51evk u-boot has an issue that system will get reset
every 2 hours.
MC13892 has an inside charge timer which expires in 120 minutes.
If ICHRG and CHGAUTOB are not set properly, this timer expiration
will get system power recycled.
Since mx51evk has no Li-Ion battery on board, the patch sets
ICHRG in externally powered mode and sets CHGAUTOB bit to avoid
automatic charging, so that system will not get reset by this
timer expiration.
The patch also corrects the bit field definition of register 48
(Charger 0) per latest MC13892 Reference Manual.
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
The patch removes the warning:
clock.c:291: warning: initialization from incompatible pointer type
after constification of args[]
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch fixes the reset command on imx25. The watchdog registers are 16
bits in size and not 32. This patch also adds the service register codes as
constants.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'
Signed-off-by: Jason Liu <r64343@freescale.com>
This patch adds generic support for the Samsung s3c2440 processor.
Global s3c24x0 changes to struct members converting from upper case to
lower case.
Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that the common code takes care of stripping away quotes and such
from numeric options, we no longer need to do so ourselves. So drop
the custom code we have in the Blackfin config.mk.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since some of the defines in our config.h use the generated defines, we
need to include the generated header. This fixes building of the Blackfin
start.S file (where the stack is setup).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Running the onenand command without arguments does nothing, with this
patch shows the command usage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Constraint the mmc framework to only send no more than 65535
blocks in one go during the multi-write command. This constraint
comes due to the limitation of 16bit width block counter register
at some hardware.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
Functions to store/retrieve the environment from a SPI flash was not updated
to the new environment code. The non-redundant case was
not working correctly, reporting ""Environment SPI flash not initialized"
and the code was not compiled clean in the redundant case.
The patch fixes these issue and makes the code more coherent
with other environment storage (nand, flash).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Building of NAND based boards failed sometimes (especially on MP
systems) because of incorrect / missing dependencies.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
When copying the "sed" script to generate the asm-offsets.h file from
the Linux Kbuild script into the make-asm-offsets file I missed the
fact that the former runs in a "make" context and thus uses double
"$$" to escape a single "$", while the latter is a shell script, where
this must not be done. Unfortunately the problem did not show up
during the initial tests on Power Architecture systems, but on ARM the
generated asm-offsets.h was not correct.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Out of tree building of the Netstal mcu25 board failed like
that:
Configuring for mcu25 board...
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/fixed_sdram.o: No such file or directory
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/nm_bsp.o: No such file or directory
Adapt (and simplify) the Makefile.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
This commit causes build errors like this:
cmd_net.c:301:1: error: macro "U_BOOT_CMD" requires 6 arguments, but only 5 given
cmd_net.c:298: warning: data definition has no type or storage class
cmd_net.c:298: warning: type defaults to 'int' in declaration of 'U_BOOT_CMD'
This reverts commit 8f4cb77ef7.
Commit 7e263ce "post/i2c: Clean up detection logic" added a "const"
qualifier to the declaration of i2c_addr_list[], missing the fact that
the list gets modified later in the code, which results in build
errors like these:
i2c.c: In function 'i2c_post_test':
i2c.c:88: error: assignment of read-only location
Remove the incorrect "const".
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Nobuhiro Iwamatsu