This patch adds the initial support for DM6467 EVM.
Other features like NET and NAND support will be added as follow up patches.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This change fixes the compiler warning
main.c: In function 'abortboot':
main.c:122: warning: too few arguments for format
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This change fixes the compiler warning
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF
for correct output!
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch re-formats the arm920t s3c24x0 nand driver in preparation for changes
to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4, 2/4 and 3/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch re-formats the arm920t s3c24x0 header files in preparation for
changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patch 1/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch re-formats the code in cpu/arm920t and cpu/arm920t/23c24x0 in
preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets and no
new warnings or errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and
s3c2410 cpu's which fixes various problems such as the timeouts in tftp being
too short.
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't
have any s3c2400 or s3c2410 boards but need this patch applying before I can
submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets
and no new warnings or errors were found.
It was originally submitted on 21/06/2009 but didn't get into the 2009.08
release, and Jean-Pierre made one comment on the original patch (see
http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two
changes to the original patch:
- it's been re-based to the current release
- I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment
This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it
directly to the maintainers of all except the sbc2410 which doesn't have an
entry in MAINTAINERS.
Signed-off-by: Kevin Morfitt <kmorfitt@aselaptop-1.localdomain>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch includes the onenand driver for s5pc100
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds support for the Samsung s5pc100 and s5pc110
SoCs. The s5pc1xx SoC is an ARM Cortex A8 processor.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
FLAG_PARSE_SEMICOLON is not defined without hush.h, so include that.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Refactor the smc911x driver to allow for detecting when the chip is missing.
I.e. the detect_chip() function is called earlier and will abort gracefully
when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Some DaVinci SOC's use GPIOs to enable EMAC and DM9000.
This patch adds some definitions for GPIO registers and also adds
structures for GPIO.
A separate header file is being added so that in future we
can have a DaVinci GPIO driver similer to OMAP.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
In the DaVinci specific code, we use both CONFIG_SOC_DM646X and
CONFIG_SOC_DM646x to represent DM646x specific code.
This patch changes occurrences of CONFIG_SOC_DM646x to
CONFIG_SOC_DM646X. This is because for DM644x series of SOCs we use
the flag CONFIG_SOC_DM644X. We want some uniformity.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on mv88f6281gtw_ge board.
To create Kirkwood boot image to be flashed on SPI Flash,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on rd6281a platform.
To create Kirkwood boot image to be flashed on NAND,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag.
This is already included when we include the
config_cmd_default.h header file. So this flag is removed.
Also another flag to enable NAND functions was being
enabled incorrectly.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The DaVinci DM365 EVM board specific code was including a header file
which does not exist. So removing this header file.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch does the following
1) Enables the NAND driver which is now available.
2) Enables the 'CONFIG_MTD_DEVICE' as without this the
compilation will fail
3) We now have a safe place to store environment and defines
an offset where this can be stored. This offset value is such that it is after
the location where U-Boot is flashed using TI flash utilities.
4) Enables Bootdelay
5) Increases malloc() arena size. Manufacturers are coming out with
NAND with large blocks sizes of upto 1 MiB. It has been noticed that
as the block size of the NAND used is increased, if this particular
value is not increased, the NAND driver will output out of memory
errors.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
DM646x is an SOC from TI which has both an ARM and a DSP.
There are multiple variants of the SOC mainly dealing with different
core speeds.
This patch adds the initial framework for the DM646x SOC.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The Default mode that is built for the Davinci DVEVM happens
to be the NOR mode.
When we want to build for the NAND mode, we get a compilation
error. This is overcome by defining the CONFIG_MTD_DEVICE
flag in the NAND mode.
The image built for NAND mode was successfully tested on the
DaVinci DM6446 EVM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
v7_flush_dcache_all, because it depends on omap ROM code is not
generic. Rename the function to 'invalidate_dcache' and move it
to the omap cpu directory.
Collect the other omap cache routines l2_cache_enable and
l2_cache_disable with invalide_dcache into cache.S. This
means removing the old cache.c file that contained l2_cache_enable
and l2_cache_disable.
The conversion from cache.c to cache.S was done most through
disassembling the uboot binary. The only significant change was
to change the comparision for the return of get_cpu_rev from
cmp r0, #0
beq earlier_than_label
Which was lost information to
cmp r0, #CPU_3XX_ES20
blt earlier_than_label
The paths through the enable routine were verified by
adding an infinite loop and seeing the hang. Then
removing the infinite loop and seeing it continue.
The disable routine is similar enough that it was not
tested with this method.
Run tested by cold booting from nand on beagle and zoom1.
Compile tested on MAKEALL arm.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Forcing the tables into got2 caused extra relocation when using -mrelocatable.
This patch requires any board defining CONFIG_BIOSEMU to use -mrelocatable.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Jin Zhengxiong <Jason.Jin@freescale.com>
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:
MII_INIT - Generic code to enable the MII bus (optional)
MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
int (*delay)() - Delay function
void *priv - Private data used by board specific code
The board code will look like:
struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
{ .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
NULL is an absolute value and should not be relocated.
After this correction code like:
void weak_fun(void) __attribute__((weak));
printf("weak_fun:%p\n", weak_fun);
will still print null after relocation.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
When U-Boot is relocated from flash to RAM pointers are modified
accordingly. However, pointers initialzed with NULL values should not
be modified so that they maintain their intended NULL value. If the
BSS segment is linked at address 0 its address will not be
updated as necessary during relocation.
This is a temporary workaround. The end goal is to add support to
U-Boot to dynamically locate the BSS at an arbitrary address at
runtime. When the ability to fixup the BSS inteligently is
added, this workaround can be removed and the 85xx link script
can put the BSS at a fixed address at link time.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 054197ba and later fixes used an array to initialize some of
the MDDRC parameters; however, the use of an array turned out to be a
bad idea as it was not possible to correlate structure entries to
array indices in readable and reliable way. Now we use a struct
instead, which makes this self-explanatory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
After running checkstyle.pl on the three previous patches I noted that in
the *.h files there were a lot of long lines. This patch solves this problem.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The command "reginfo" got an overhaul for the ppc4xx. It dumps all the
relevant HW configuration registers (address, symbolic name, content).
This allows to easily detect errors in *.h files and changes in the HW
configuration.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Sandeep Paulraj