On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I hit an oops at boot on the first instruction of timer_cpu_notify:
NIP [c000000000722f88] .timer_cpu_notify+0x0/0x388
The code should look like:
c000000000722f78: eb e9 00 30 ld r31,48(r9)
c000000000722f7c: 2f bf 00 00 cmpdi cr7,r31,0
c000000000722f80: 40 9e ff 44 bne+ cr7,c000000000722ec4
c000000000722f84: 4b ff ff 74 b c000000000722ef8
c000000000722f88 <.timer_cpu_notify>:
c000000000722f88: 7c 08 02 a6 mflr r0
c000000000722f8c: 2f a4 00 07 cmpdi cr7,r4,7
c000000000722f90: fb c1 ff f0 std r30,-16(r1)
c000000000722f94: fb 61 ff d8 std r27,-40(r1)
But the oops output shows:
eb61ffd8 eb81ffe0 eba1ffe8 ebc1fff0 7c0803a6 ebe1fff8 4e800020
00000000 ebe90030 c0000000 00ad0a28 00000000 2fa40007 fbc1fff0 fb61ffd8
So we scribbled over our instructions with c000000000ad0a28, which
is an address inside the jump_table ELF section.
It turns out the jump_table section is only aligned to 8 bytes but
we are aligning our entries within the section to 16 bytes. This
means our entries are offset from the table:
c000000000acd4a8 <__start___jump_table>:
...
c000000000ad0a10: c0 00 00 00 lfs f0,0(0)
c000000000ad0a14: 00 70 cd 5c .long 0x70cd5c
c000000000ad0a18: c0 00 00 00 lfs f0,0(0)
c000000000ad0a1c: 00 70 cd 90 .long 0x70cd90
c000000000ad0a20: c0 00 00 00 lfs f0,0(0)
c000000000ad0a24: 00 ac a4 20 .long 0xaca420
And the jump table sort code gets very confused and writes into the
wrong spot. Remove the alignment, and also remove the padding since
we it saves some space and we shouldn't need it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a box that fails in OF during boot with:
DEFAULT CATCH!, exception-handler=fff00400
at %SRR0: 49424d2c4c6f6768 %SRR1: 800000004000b002
ie "IBM,Logh". OF got corrupted with a device tree string.
Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.
Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.
This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit af9eef3c7b caused cpu_setup to see
the_cpu_spec, rather than the source struct. However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct. So if cpu_setup patches
the feature bits, the update won't affect the fixups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a cast in case the caller passes in a different type, as it would
if mtspr/mtmsr were functions.
Previously, if a 64-bit type was passed in on 32-bit, GCC would bind the
constraint to a pair of registers, and would substitute the first register
in the pair in the asm code. This corresponds to the upper half of the
64-bit register, which is generally not the desired behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit a0bfa13738 mispells
cpuidle_idle_call() on ARM and SH code. Fix this to be consistent.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: x86@kernel.org
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
[ Also done by Mark Brown - th ebug has been around forever, and was
noticed in -next, but the idle tree never picked it up. Bad bad bad ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Three places in the kernel assume that the only long mode CPL 3
selector is __USER_CS. This is not true on Xen -- Xen's sysretq
changes cs to the magic value 0xe033.
Two of the places are corner cases, but as of "x86-64: Improve
vsyscall emulation CS and RIP handling"
(c9712944b2), vsyscalls will segfault
if called with Xen's extra CS selector. This causes a panic when
older init builds die.
It seems impossible to make Xen use __USER_CS reliably without
taking a performance hit on every system call, so this fixes the
tests instead with a new paravirt op. It's a little ugly because
ptrace.h can't include paravirt.h.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/f4fcb3947340d9e96ce1054a432f183f9da9db83.1312378163.git.luto@mit.edu
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Xen needs to handle VVAR_PAGE, introduced in git commit:
9fd67b4ed0
x86-64: Give vvars their own page
Otherwise we die during bootup with a message like:
(XEN) mm.c:940:d10 Error getting mfn 1888 (pfn 1e3e48) from L1 entry
8000000001888465 for l1e_owner=10, pg_owner=10
(XEN) mm.c:5049:d10 ptwr_emulate: could not get_page_from_l1e()
[ 0.000000] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 0.000000] IP: [<ffffffff8103a930>] xen_set_pte+0x20/0xe0
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/4659478ed2f3480938f96491c2ecbe2b2e113a23.1312378163.git.luto@mit.edu
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Gold has trouble assigning numbers to the location counter inside of
an output section description. The bug was triggered by
9fd67b4ed0, which consolidated all of
the vsyscall sections into a single section. The workaround is IMO
still nicer than the old way of doing it.
This produces an apparently valid kernel image and passes my vdso
tests on both GNU ld version 2.21.51.0.6-2.fc15 20110118 and GNU
gold (version 2.21.51.0.6-2.fc15 20110118) 1.10 as distributed by
Fedora 15.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/0b260cb806f1f9a25c00ce8377a5f035d57f557a.1312378163.git.luto@mit.edu
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The spec says this takes uint32 for attributes, not uintn.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
WARN message should not complain
"Failed to release memory %lx-%lx err=%d\n"
^^^^^^^
about range when it fails to release just one page,
instead it should say what pfn is not freed.
In addition line:
printk(KERN_INFO "xen_release_chunk: looking at area pfn %lx-%lx: "
...
printk(KERN_CONT "%lu pages freed\n", len);
will be broken if WARN in between this line is fired. So fix it
by using a single printk for this.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use correct format specifier for unsigned long.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Apparently we wanted CONFIG_FTRACE rather the CONFIG_FUNCTION_TRACER.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] wire up sendmmsg syscall
[PARISC] fix return type of __atomic64_add_return
[PARISC] Fix futex support
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] signal: use set_restore_sigmask() helper
[S390] smp: remove pointless comments in startup_secondary()
[S390] qdio: Use kstrtoul_from_user
[S390] sclp_async: Use kstrtoul_from_user
[S390] exec: remove redundant set_fs(USER_DS)
[S390] cpu hotplug: on cpu start wait until being marked active
[S390] signal: convert to use set_current_blocked()
[S390] asm offsets: fix coding style
[S390] Add support for IBM zEnterprise 114
[S390] dasd: check if raw track access is supported
[S390] Use diagnose 308 for system reset
[S390] Export store_status() function
[S390] dasd: use vmalloc for statistics input buffer
[S390] Add PSW restart shutdown trigger
[S390] missing return in page_table_alloc_pgste
[S390] qdio: 2nd stage retry on SIGA-W busy conditions
Dmitry Kasatkin reports:
"kernel-devel package with kernel headers have no <include/xen>
directory if XEN is disabled. Modules which inclide asm/io.h won't
compile.
XEN related content is behind the CONFIG_XEN flag in the io.h. And
<xen/xen.h> should be also behind CONFIG_XEN flag."
So move the include of <xen/xen.h> down into the section that is
conditional on CONFIG_XEN.
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle: stop depending on pm_idle
x86 idle: move mwait_idle_with_hints() to where it is used
cpuidle: replace xen access to x86 pm_idle and default_idle
cpuidle: create bootparam "cpuidle.off=1"
mrst_pmu: driver for Intel Moorestown Power Management Unit
* 'apei-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI, APEI, EINJ Param support is disabled by default
APEI GHES: 32-bit buildfix
ACPI: APEI build fix
ACPI, APEI, GHES: Add hardware memory error recovery support
HWPoison: add memory_failure_queue()
ACPI, APEI, GHES, Error records content based throttle
ACPI, APEI, GHES, printk support for recoverable error via NMI
lib, Make gen_pool memory allocator lockless
lib, Add lock-less NULL terminated single list
Add Kconfig option ARCH_HAVE_NMI_SAFE_CMPXCHG
ACPI, APEI, Add WHEA _OSC support
ACPI, APEI, Add APEI bit support in generic _OSC call
ACPI, APEI, GHES, Support disable GHES at boot time
ACPI, APEI, GHES, Prevent GHES to be built as module
ACPI, APEI, Use apei_exec_run_optional in APEI EINJ and ERST
ACPI, APEI, Add apei_exec_run_optional
ACPI, APEI, GHES, Do not ratelimit fatal error printk before panic
ACPI, APEI, ERST, Fix erst-dbg long record reading issue
ACPI, APEI, ERST, Prevent erst_dbg from loading if ERST is disabled
Unfortunately, the module fixups cause the kernel to fail to build
when SMP is not enabled. Fix this by removing the reference to
fixup_smp on non-SMP fixup kernels, but ensuring that if we do have
the SMP fixup section, we refuse to load the module.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/cris/arch-v10/kernel/irq.c:239: error: implicit declaration of function 'kgdb_init'
arch/cris/arch-v10/kernel/irq.c:240: error: implicit declaration of function 'breakpoint'
Declare these two functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix:
arch/cris/arch-v10/drivers/sync_serial.c:628: error: 'ret' undeclared (first use in this function)
'ret' should be 'err'.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this error:
kernel/fork.c:267: error: implicit declaration of function 'alloc_thread_info_node'
This is due to renaming alloc_thread_info() to alloc_thread_info_node().
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpuidle users should call cpuidle_call_idle() directly
rather than via (pm_idle)() function pointer.
Architecture may choose to continue using (pm_idle)(),
but cpuidle need not depend on it:
my_arch_cpu_idle()
...
if(cpuidle_call_idle())
pm_idle();
cc: Kevin Hilman <khilman@deeprootsystems.com>
cc: Paul Mundt <lethal@linux-sh.org>
cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
...and make it static
no functional change
cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a Xen Dom0 kernel boots on a hypervisor, it gets access
to the raw-hardware ACPI tables. While it parses the idle tables
for the hypervisor's beneift, it uses HLT for its own idle.
Rather than have xen scribble on pm_idle and access default_idle,
have it simply disable_cpuidle() so acpi_idle will not load and
architecture default HLT will be used.
cc: xen-devel@lists.xensource.com
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Moorestown (MRST) Power Management Unit (PMU) driver
directs the SOC power states in the "Langwell" south complex (SCU).
It hooks pci_platform_pm_ops[] and thus observes all PCI ".set_state"
requests. For devices in the SC, the pmu driver translates those
PCI requests into the appropriate commands for the SCU.
The PMU driver helps implement S0i3, a deep system idle power idle state.
Entry into S0i3 is via cpuidle, just like regular processor c-states.
S0i3 depends on pre-conditions including uni-processor, graphics off,
and certain IO devices in the SC must be off. If those pre-conditions
are met, then the PMU allows cpuidle to enter S0i3, otherwise such requests
are demoted, either to Atom C4 or Atom C6.
This driver is based on prototype work by Bruce Flemming,
Illyas Mansoor, Rajeev D. Muralidhar, Vishwesh M. Rudramuni,
Hari Seshadri and Sujith Thomas. The current driver also
includes contributions from H. Peter Anvin, Arjan van de Ven,
Kristen Accardi, and Yong Wang.
Thanks for additional review feedback from Alan Cox and Randy Dunlap.
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some trivial conflicts due to other various merges
adding to the end of common lists sooner than this one.
arch/ia64/Kconfig
arch/powerpc/Kconfig
arch/x86/Kconfig
lib/Kconfig
lib/Makefile
Signed-off-by: Len Brown <len.brown@intel.com>
cmpxchg() is widely used by lockless code, including NMI-safe lockless
code. But on some architectures, the cmpxchg() implementation is not
NMI-safe, on these architectures the lockless code may need a
spin_trylock_irqsave() based implementation.
This patch adds a Kconfig option: ARCH_HAVE_NMI_SAFE_CMPXCHG, so that
NMI-safe lockless code can depend on it or provide different
implementation according to it.
On many architectures, cmpxchg is only NMI-safe for several specific
operand sizes. So, ARCH_HAVE_NMI_SAFE_CMPXCHG define in this patch
only guarantees cmpxchg is NMI-safe for sizeof(unsigned long).
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Richard Henderson <rth@twiddle.net>
CC: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
CC: Yoshinori Sato <ysato@users.sourceforge.jp>
CC: Tony Luck <tony.luck@intel.com>
CC: Hirokazu Takata <takata@linux-m32r.org>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Michal Simek <monstr@monstr.eu>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: Kyle McMartin <kyle@mcmartin.ca>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Chen Liqin <liqin.chen@sunplusct.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Len Brown <len.brown@intel.com>
We should call set_restore_sigmask() instead of directly setting
TIF_RESTORE_SIGMASK. This change should have been done three years
earlier... see 4e4c22 "signals: add set_restore_sigmask".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Remove pointless comments in startup_secondary(). There is not too much
value in having comments like e.g. "call cpu notifiers" just before a
call to notify_cpu*().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This is the same as fd8a7de1 "x86: cpu-hotplug: Prevent softirq wakeup
on wrong CPU".
Unlike on x86 this doesn't fix a bug on s390 since we do not have
threaded interrupt handlers. However we want to keep the same
initialization order like on x86. This should prevent bugs caused by
code which assumes (and relies on) the init order is the same on each
architecture.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Because of readability reasons we ignore the 80 character line limit
in asm offsets. Just one line per define, nothing else.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The diagnose 308 call is the prefered method for clearing all ongoing I/O.
Therefore if it is available we use it instead of doing a manual reset.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
For kdump we need a store status function to save the registers for the
current CPU. Therefore this patch exports a function "store_status()".
In addition to that now also floating point registers are saved correctly.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
With this patch a new S390 shutdown trigger "restart" is added. If under
z/VM "systerm restart" is entered or under the HMC the "PSW restart" button
is pressed, the PSW located at 0 (31 bit) or 0x1a0 (64 bit) bit is loaded.
Now we execute do_restart() that processes the restart action that is
defined under /sys/firmware/shutdown_actions/on_restart. Currently the
following actions are possible: reipl (default), stop, vmcmd, dump, and
dump_reipl.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Fix the following compile warning for !CONFIG_PGSTE:
CC arch/s390/mm/pgtable.o
arch/s390/mm/pgtable.c: In function ‘page_table_alloc_pgste’:
arch/s390/mm/pgtable.c:531:1: warning: no return statement in function returning non-void [-Wreturn-type]
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile/mm/init.c: trivial: use BUG_ON
arch/tile: remove useless set_fixmap_nocache() macro
arch/tile: add hypervisor-based character driver for SPI flash ROM
ioctl-number.txt: add the tile hardwall ioctl range
tile: use generic-y format for one-line asm-generic headers
clocksource: tile: convert to use clocksource_register_hz
Don't use floating point on Niagara2, use the traditional
plain Niagara code instead.
Unroll Niagara loops to 128 bytes for copy, and 256 bytes
for clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
No need to have a separate header file containing only register
definitions that are used by a single driver. Fold these into the
gpio driver.
Signed-off-by: David Brown <davidb@codeaurora.org>
The gpiomux.h header contains some SOC ifdefs. However, the API that
is actually used by the GPIO driver only uses two functions that are
general. Move these general definitions into a public header file.
Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Select the GPIO register configuration at runtime rather than through
idefs.
Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.
Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The two GPIO controllers are always mapped to the same virtual address
across all MSM devices. Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.
Change-Id: I1672219d978ab6243526adeda6badf49472baa27
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.
Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Request for comment and commit.
From: T. Mehnert <t.mehnert@eckelmann.de>
Date: Mon, 4 Jul 2011 15:53:30 +0200
Subject: [PATCH] i.MX25 GPT clock fix: ensure correct the clock source
This patch ensures, that Linux will take the correct clock source (AHB_DIV)
for gpt in the ARM i.MX25 implementation. The currect code depends on the reset
defaults of the CCM_MCR register. So on some boards it could happen that the
UPLL is used for clock source, which results in faulty time behavior in Linux.
In this case all delays or sleeps will will be faktor 1.8 too long.
Signed-off-by: Torsten Mehnert <t.mehnert@eckelmann.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/math-emu: Remove unnecessary code
m68k/math-emu: Remove commented out old code
m68k: Kill warning in setup_arch() when compiling for Sun3
m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
sparc: iounmap() and *_free_coherent() - Use lookup_resource()
m68k/atari: Reserve some ST-RAM early on for device buffer use
m68k/amiga: Chip RAM - Use lookup_resource()
resources: Add lookup_resource()
sparc: _sparc_find_resource() should check for exact matches
m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
m68k/amiga: Chip RAM - Change chipavail to an atomic_t
m68k/amiga: Chip RAM - Always allocate from the start of memory
m68k/amiga: Chip RAM - Convert from printk() to pr_*()
m68k/amiga: Chip RAM - Use tabs for indentation
It's been unused for ages, and contains bugs (e.g. incorrect shifts in
lsl64()).
Reported-by: Jonathan Elchison <jelchison@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
These defines are way to generic, and cause conflicts:
drivers/net/wireless/rtlwifi/rtl8192c/../rtl8192ce/reg.h:369:1: warning: "GPIO_IN" redefined
drivers/net/wireless/rtlwifi/rtl8192c/../rtl8192ce/reg.h:370:1: warning: "GPIO_OUT" redefined
drivers/net/wireless/rtlwifi/rtl8192se/reg.h:252:1: warning: "GPIO_IN" redefined
drivers/net/wireless/rtlwifi/rtl8192se/reg.h:253:1: warning: "GPIO_OUT" redefined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Replace a custom implementation (which doesn't lock the resource tree) by a
call to lookup_resource()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Based on an original patch from Michael Schmitz:
Because mem_init() is now called before device init, devices that rely on
ST-RAM may find all ST-RAM already allocated to other users by the time
device init happens. In particular, a large initrd RAM disk may use up
enough of ST-RAM to cause atari_stram_alloc() to resort to
__get_dma_pages() allocation.
In the current state of Atari memory management, all of RAM is marked
DMA capable, so __get_dma_pages() may well return RAM that is not in actual
fact DMA capable. Using this for frame buffer or SCSI DMA buffer causes
subtle failure.
The ST-RAM allocator has been changed to allocate memory from a pool of
reserved ST-RAM of configurable size, set aside on ST-RAM init (i.e.
before mem_init()). As long as this pool is not exhausted, allocation of
real ST-RAM can be guaranteed.
Other changes:
- Replace the custom allocator in the ST-RAM pool by the existing allocator
in the resource subsystem,
- Remove mem_init_done and its hook, as memory init is now done before
device init,
- Remove /proc/stram, as ST-RAM usage now shows up under /proc/iomem, e.g.
005f2000-006f1fff : ST-RAM Pool
005f2000-0063dfff : atafb
0063e000-00641fff : ataflop
00642000-00642fff : SCSI
Signed-off-by: Michael Schmitz <schmitz@debian.org>
[Andreas Schwab <schwab@linux-m68k.org>: Use memparse()]
[Geert: Use the resource subsystem instead of a custom allocator]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Replace a custom implementation (which doesn't lock the resource tree) by a
call to lookup_resource()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The address that's passed to _sparc_find_resource() should always be the
start address of a resource:
- iounmap() passes a page-aligned virtual address, while the original
address was created by adding the in-page offset to the resource's
start address,
- sbus_free_coherent() and pci32_free_coherent() should be passed an
address obtained from sbus_alloc_coherent() resp. pci32_alloc_coherent(),
which is always a resource's start address.
Hence replace the range check by a check for an exact match.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
While the core resource handling code is safe, our global counter must
still be protected against concurrent modifications.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
As of commit 5df1abdbd3 ('m68k/amiga: Fix
"debug=mem"'), "debug=mem" no longer uses amiga_chip_alloc_res(), so we
can remove the hack to prefer memory at the safe end.
This allows to simplify the code and make amiga_chip_alloc() just call
amiga_chip_alloc_res() internally.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
and fix a few formattings:
- resource sizes are now resource_size_t, use %pR to make it future proof,
- use %lu for unsigned long.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'at91/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
at91: add arch specific ioremap support
at91: factorize sram init
at91: move register clocks to soc generic init
at91: move clock subsystem init to soc generic init
at91: use structure to store the current soc
at91: remove AT91_DBGU offset from dbgu register macro
at91: factorize at91 interrupts init to soc
at91: introduce commom AT91_BASE_SYS
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
The return type of __atomic64_add_return of should be s64 or long, not
int. This fixes the atomic64 test failure that I previously reported.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of evaluating the cpu features for ELF_HWCAP every exec,
calculate it once at boot time.
Add AV_SPARC_* capability flag bits, compatible with what Solaris
reports to applications.
Report these capabilities once in the kernel log, and also via
/proc/cpuinfo in a new "cpucaps" entry.
If available, fetch the cpu features from the machine description
'hwcap-list' property of the 'cpu' node.
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous commit left the file empty and present in the
Makefile, which is a bit dirty and caused problems with
'make distclean', as pointed out by David Howells.
This hopefully cleans it up the right way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: John Linn <john.linn@xilinx.com>
instead of reading the registers everytime
the current implementation respect the following constrain:
- allow 1 to n soc to be enabled
- allow to have a virtual cpu type and subtype
- always detect the cpu type and subtype and report it
- detect if the soc support is enabled
- prepare for sysfs export support
- drop soc specific code via compiler when the soc not enabled
(via cpu_is_xxx)
Today if we read the exid we will have the same value for 9g35 and 9m11
and we will need to check the cidr too
with the new implementation we just need to check the soc subtype
this will also allow to have specific virtual subtype for rm9200 which the
board will have to specify via at91rm9200_set_type(int) as we have no way to
detect it.
this implementation is inspired by the SH cpu detection support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For testing the dt work, define a dt-enabled versatile platform.
This patch adds a new versatile platform for when using the device
tree. Add platform and amba devices are discovered and registered by
parsing the device tree. Clocks and initial io mappings are still
configured statically.
This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The cpu compatible string we look for is "SPARC-T3".
As far as memset/memcpy optimizations go, we treat this chip the same
as Niagara-T2/T2+. Use cache initializing stores for memset, and use
perfetch, FPU block loads, cache initializing stores, and block stores
for copies.
We use the Niagara-T2 perf support, since T3 is a close relative in
this regard. Later we'll add support for the new events T3 can
report, plus enable T3's new "sample" mode.
For now I haven't added any new ELF hwcap flags. We probably need
to add a couple, for example:
T2 and T3 both support the population count instruction in hardware.
T3 supports VIS3 instructions, including support (finally) for
partitioned shift. One can also now move directly between float
and integer registers.
T3 supports instructions meant to help with Galois Field and other HPC
calculations, such as XOR multiply. Also there are "OP and negate"
instructions, for example "fnmul" which is multiply-and-negate.
T3 recognizes the transactional memory opcodes, however since
transactional memory isn't supported: 1) 'commit' behaves as a NOP and
2) 'chkpt' always branches 3) 'rdcps' returns all zeros and 4) 'wrcps'
behaves as a NOP.
So we'll need about 3 new elf capability flags in the end to represent
all of these things.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hypervisor call is only necessary if hypervisor events are
being requested.
So if we're not tracking hypervisor events, simply do a direct
register write.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that v4l2 subdevices have got their own device objects, having
one more device in soc-camera clients became redundant and confusing.
This patch removes those devices and the soc-camera bus, they used to
reside on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RX-51 uses the CSIb IO complex for camera operation. The
board file is missing definition for the regulator supplying
the CSIb complex, so this is added for better power
management.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Should have been done in commit 1af08a1407f4 ("This is in preparation
for more generic atomic").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arun Sharma <asharma@fb.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Hans-Christian Egtvedt" <hans-christian.egtvedt@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Do not show error message for 32 interrupt lines
Revert "microblaze: PCI fix typo fault in of_node pointer moving into pci_bus"
microblaze: PCI fix typo fault in of_node pointer moving into pci_bus
microblaze: Add support for early console on mdm
microblaze: Simplify early console binding from DT
microblaze: Get early printk console earlier
microblaze: Standardise cpuinfo output for cache policy
microblaze: Unprivileged stream instruction awareness
microblaze: trivial: Fix typo fault
microblaze: exec: Remove redundant set_fs(USER_DS)
microblaze: Remove duplicated prototype of start_thread()
microblaze: Fix unaligned value saving to the stack for system with MMU
microblaze/irqs: Do not trace arch_local_{*,irq_*} functions
Fix kconfig dependency warning:
warning: (KVM) selects TASK_DELAY_ACCT which has unmet direct dependencies (TASKSTATS)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
When interrupt controller uses 32 interrupts lines the kernel
show error message about mismatch in kind-of-intr parameter
because it exceeds u32. Recast fixs this issue.
Signed-off-by: Michal Simek <monstr@monstr.eu>
It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version. Instead,
soc name is stable enough to define the device type.
The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported. The changes include:
* Turn platform_data from optional to mandatory
* Add cd_types and wp_types into platform_data to cover more use
cases
* Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
* Adjust some machine codes to adopt the platform_data changes
* Work around the issue that software reset will get card detection
circuit stop working
With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.
The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy. The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reported-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
The patch removes all the uses of cpu_is_mx1(). Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART. The IMX21_UART type runs on all i.mx
except i.mx1.
A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.
It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: S3C64XX: Configure backup battery charger on Cragganmore
ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
ARM: S3C64XX: Configure supplies for all Cragganmore regulators
ARM: S3C64XX: Refresh Cragganmore support
ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
OMAP4: Keyboard: Mux changes in the board file
omap: blaze: add mmc5/wl1283 device support
omap: 4430SDP: Register the card detect GPIO properly
arm: omap3: cm-t35: add support for cm-t3730
OMAP3: beagle: add support for beagleboard xM revision C
OMAP3: rx-51: Add full regulator definitions
omap: rx51: Platform support for lp5523 led chip
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.
This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harmonise these return values with other architectures. In some cases
this affects all compilers and in other cases non-gcc compilers only.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ulrich Drepper <drepper@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Also removed the dead code in flush_thread().
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c9d761b7c4.
Ben' commit "microblaze/pci: Move the remains of pci_32.c to pci-common.c"
(sha1: bf13a6fa09)
completely removed pci_32.c that's why my fixing commit caused
the problem with merging and need to be revert.
Signed-off-by: Michal Simek <monstr@monstr.eu>
On MX51 Babbage board the RTS/CTS pins are not used on UART2 port.
Fix the registration of this port.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code is assuming that gpio_get_value() is returning 0 or 1 but it
should be checking if the value is 0 or not. Not doing it properly is breaking
the detection of the board (and thus the reboot of efika mx to2) when using
the new mxc gpio driver, which relies on basic mmio gpio.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While testing the keys, I only checked that the key were generating an input
event but unfortunately, they were not generating the right event. Fix that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx51_initialize_usb_hw() support introduced a small error. The usbh1 has
pdev->id equal to 1 not 0, so use pdev->id to make things less error-prone and
to fix that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I2C signals SDA/SCL are a bit different, they need to be pull-up and
open-drain (so to support multiple I2C devices).
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following section mismatches:
WARNING: vmlinux.o(.text+0x1026c): Section mismatch in reference from the function lilly1131_usb_init() to the variable .init.rodata:imx31_mxc_ehci_hs_data
The function lilly1131_usb_init() references
the variable __initconst imx31_mxc_ehci_hs_data.
This is often because lilly1131_usb_init lacks a __initconst
annotation or the annotation of imx31_mxc_ehci_hs_data is wrong.
WARNING: vmlinux.o(.text+0x10270): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.rodata:(unknown)
The function lilly1131_usb_init() references
the (unknown reference) __initconst (unknown).
This is often because lilly1131_usb_init lacks a __initconst
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x10274): Section mismatch in reference from the function lilly1131_usb_init() to the (unknown reference) .init.data:(unknown)
The function lilly1131_usb_init() references
the (unknown reference) __initdata (unknown).
This is often because lilly1131_usb_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following section mismatches:
WARNING: vmlinux.o(.text+0x101cc): Section mismatch in reference from the function mxc_init_i2c() to the (unknown reference) .init.data:(unknown)
The function mxc_init_i2c() references
the (unknown reference) __initdata (unknown).
This is often because mxc_init_i2c lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x101d8): Section mismatch in reference from the function mxc_init_i2c() to the variable .init.rodata:imx31_imx_i2c_data
The function mxc_init_i2c() references
the variable __initconst imx31_imx_i2c_data.
This is often because mxc_init_i2c lacks a __initconst
annotation or the annotation of imx31_imx_i2c_data is wrong.
WARNING: vmlinux.o(.text+0x10200): Section mismatch in reference from the function mxc_init_audio() to the variable .init.rodata:imx31_imx_ssi_data
The function mxc_init_audio() references
the variable __initconst imx31_imx_ssi_data.
This is often because mxc_init_audio lacks a __initconst
annotation or the annotation of imx31_imx_ssi_data is wrong.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without this platform data the aic32x4 audio
codec in the Visstrim_M10 won't work properly.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
staging:iio:kfifo_buf fix double initialization of the ring device structure.
staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
staging:iio:imu fix missing register table index for some channels
spectra: enable device before poking it
staging: rts_pstor: Fix a miswriting
staging/lirc_bt829: Return -ENODEV when no hardware is found.
staging/lirc_parallel: remove pointless prototypes.
staging/lirc_parallel: fix panic on rmmod
staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
Staging: zram: Fix kunmapping order
Revert "gma500: Fix dependencies"
gma500: Add medfield header
gma500: wire up the mrst i2c bus from chip_info
gma500: Fix DPU build
gma500: Clean up the DPU config and make it runtime
gma500: resync with Medfield progress
gma500: Use the mrst helpers and power control for mode commit
gma500@ Fix backlight range error
gma500: More Moorestown muddle meddling means MM maybe might modeset
...
Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
- Documentation/feature-removal-schedule.txt
- drivers/staging/bcm/headers.h
- drivers/staging/brcm80211/brcmfmac/dhd_linux.c
- drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
- drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
- drivers/staging/brcm80211/brcmfmac/wl_iw.c
- drivers/staging/et131x/et131x_netdev.c
- drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
- drivers/staging/rtl8192e/r8192E.h
- drivers/staging/usbip/userspace/src/utils.h
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: Revive reporting of spurious interrupts
m68knommu: Move forward declaration of do_IRQ() from machdep.h to irq.h
m68k: fix some atomic operation asm address modes for ColdFire
m68k: use CPU_HAS_NO_BITFIELDS for signal functions
m68k: merge and clean up delay.h files
m68knommu: correctly use trap_init
m68knommu: merge ColdFire 5206 and 5206e platform code
m68k: merge mmu and non-mmu bitops.h
m68k: merge MMU and non MMU versions of system.h
m68k: merge MMU and non-MMU versions of asm/hardirq.h
m68k: merge the non-mmu and mmu versions of module.c
m68knommu: Fix printk() format in free_initrd_mem()
m68knommu: Make empty_zero_page "void *", like on m68k
* 'for-3.1' of git://linux-nfs.org/~bfields/linux:
nfsd: don't break lease on CLAIM_DELEGATE_CUR
locks: rename lock-manager ops
nfsd4: update nfsv4.1 implementation notes
nfsd: turn on reply cache for NFSv4
nfsd4: call nfsd4_release_compoundargs from pc_release
nfsd41: Deny new lock before RECLAIM_COMPLETE done
fs: locks: remove init_once
nfsd41: check the size of request
nfsd41: error out when client sets maxreq_sz or maxresp_sz too small
nfsd4: fix file leak on open_downgrade
nfsd4: remember to put RW access on stateid destruction
NFSD: Added TEST_STATEID operation
NFSD: added FREE_STATEID operation
svcrpc: fix list-corrupting race on nfsd shutdown
rpc: allow autoloading of gss mechanisms
svcauth_unix.c: quiet sparse noise
svcsock.c: include sunrpc.h to quiet sparse noise
nfsd: Remove deprecated nfsctl system call and related code.
NFSD: allow OP_DESTROY_CLIENTID to be only op in COMPOUND
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
Page table entries are made invalid by writing a zero into the the PTE
slot in a page table. This creates a race condition with the TLB
modify handlers when they are updating the PTE.
CPU0 CPU1
Test for _PAGE_PRESENT
. set to not _PAGE_PRESENT (zero)
Set to _PAGE_VALID
So now the page not present value (zero) is suddenly valid and user
space programs have access to physical page zero.
We close the race by putting the test for _PAGE_PRESENT and setting of
_PAGE_VALID into an atomic LL/SC section. This requires more registers
than just K0 and K1 in the handlers, so we need to save some registers
to a save area and then restore them when we are done.
The save area is an array of cacheline aligned structures that should
not suffer cache line bouncing as they are CPU private.
[ralf@linux-mips.org: Fix !defined(CONFIG_MIPS_PGD_C0_CONTEXT) build error.]
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2577/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This can be used from either 32-bit or 64-bit code to generate logical
right shifts of any constant amount.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
From: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
platform data for simple backlight driver for LM3530
in the u5500 platform
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not necessary to share the same notifier.h.
This patch already moves register_reboot_notifier() and
unregister_reboot_notifier() from kernel/notifier.c to kernel/sys.c.
[amwang@redhat.com: make allyesconfig succeed on ppc64]
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GCC 4.6's -Wunused-but-set-variable found some dead code.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux can have pids up to 4*1024*1024. To handle such huge numbers
pid_buf needs to be larger.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Until now UML had no x86_64 vDSO. So glibc always used the vsyscall page
for gettimeday() and friends. Calls to gettimeday() returned falsely the
host time and confused some programs.
This patch adds a vDSO which turns all __vdso_* calls into a system call
so that UML can trap them.
As glibc still uses the vsyscall page for static binaries this patch
improves the situation only for dynamic binaries.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement arch_vma_name() and make get_gate_vma(), in_gate_area() and
in_gate_area_no_mm() a nop.
We need arch_vma_name() to support vDSO.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When UML is unable to reuse the host's vDSO FIXADDR_USER_START is zero.
To handle this special case correclty we have to implement custom gate
area helper methods.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reusing the host's vDSO makes only sense on x86_32.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When creating the temp file there's a memory and file descriptor leak upon
error.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not free memory when you failed to allocate it.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this warning:
arch/um/os-Linux/helper.c: In function `helper_child':
arch/um/os-Linux/helper.c:38:7: warning: ignoring return value of `write', declared with attribute warn_unused_result
[richard@nod.at: happens only with -D_FORTIFY_SOURCE=2]
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this warning:
arch/um/drivers/cow_user.c: In function `absolutize':
arch/um/drivers/cow_user.c:189:7: warning: ignoring return value of `chdir', declared with attribute warn_unused_result
[richard@nod.at: happens only with -D_FORTIFY_SOURCE=2]
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Perform memory cleanup on exit. On receiving invalid 'pid' we still
should clean 'output' variable.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0954828fcb ("kconfig: replace KERNELVERSION usage by the
mainmenu's prompt") made the kernel version disappear from the generated
.config file when configuring for UML. As UML's Kconfig doesn't have a
mainmenu, kconfig falls back to the default string "Linux Kernel
Configuration".
Add a suitable mainmenu to the main UML Kconfig file to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To make netconsole usable on UML, its ethernet driver needs netpoll
support.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When UML is compiled with _FORTIFY_SOURCE we have to export all _chk()
functions which are used in modules. For now it's only the case for
__sprintf_chk().
Tested-by: Florian Fainelli <florian@openwrt.org>
Reported-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both sys-i386 and sys-x86_64 support now ndelay(). The delay functions
are based on arch/x86/lib/delay.c.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to define VM_{STACK,DATA}_DEFAULT_FLAGS as variable.
It's also useless to test for TIF_IA32 as 64bit UML has no IA32 emulation.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some harmless warnings such as
arch/cris/arch-v32/mach-a3/pinmux.c:273: warning: ISO C90 forbids mixed declarations and code:
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so those calls to
set_fs(USER_DS) are redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luckily there are still a few software PTE bits remaining and they even
match up in both the sun4u and sun4v pte layouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make use of the generic RCU page table freeing on Sparc64, doing so allows
for race-free software page-table walkers like gup_fast().
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the recent mmu_gather changes that included generic RCU freeing of
page-tables, it is now quite straightforward to implement gup_fast() on
sparc64.
This patch:
Remove the page table quicklists. They are pointless and make it harder
to use RCU page table freeing and share code with other architectures.
BTW, this is the second time this has happened, see commit 3c93646524
("[SPARC64]: Kill pgtable quicklists and use SLAB.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following build error:
arch/xtensa/include/asm/uaccess.h:403: error: implicit declaration of function 'prefetch'
arch/xtensa/include/asm/uaccess.h:412: error: implicit declaration of function 'prefetchw'
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent an arbitrary kernel read. Check the user pointer with access_ok()
before copying data in.
[akpm@linux-foundation.org: s/EIO/EFAULT/]
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: Christian Zankel <chris@zankel.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_FUNCTION_TRACER is disabled, compilation fails as follows:
CC arch/x86/xen/setup.o
In file included from arch/x86/include/asm/xen/hypercall.h:42,
from arch/x86/xen/setup.c:19:
include/trace/events/xen.h:31: warning: 'struct multicall_entry' declared inside parameter list
include/trace/events/xen.h:31: warning: its scope is only this definition or declaration, which is probably not what you want
include/trace/events/xen.h:31: warning: 'struct multicall_entry' declared inside parameter list
include/trace/events/xen.h:31: warning: 'struct multicall_entry' declared inside parameter list
include/trace/events/xen.h:31: warning: 'struct multicall_entry' declared inside parameter list
[...]
arch/x86/xen/trace.c:5: error: '__HYPERVISOR_set_trap_table' undeclared here (not in a function)
arch/x86/xen/trace.c:5: error: array index in initializer not of integer type
arch/x86/xen/trace.c:5: error: (near initialization for 'xen_hypercall_names')
arch/x86/xen/trace.c:6: error: '__HYPERVISOR_mmu_update' undeclared here (not in a function)
arch/x86/xen/trace.c:6: error: array index in initializer not of integer type
arch/x86/xen/trace.c:6: error: (near initialization for 'xen_hypercall_names')
Fix this by making sure struct multicall_entry has a declaration in
scope at all times, and don't bother compiling xen/trace.c when tracing
is disabled.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Anton Blanchard