This starts moving out the common initialization bits from the various
fixup paths in to the shared init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the platform code is a bit leaner, we can start consolidating
the various IRQ routing implementations. There are effectively only 2
variants, and the others can use those directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 68b42d1b54 ("sh: sh7785lcr: Map
whole PCI address space.") changed around the semantics of how various
chip-selects are made accessible to PCI. Now that there is a single
large mapping covering from CS0-CS6, there is no longer any need to
do multi-window mapping. Subsequently, all of the differing
implementations can be consolidated in to pci-sh7780.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the PCI I/O and memory window definitions across
the pci-sh7780 users in pci-sh7780 itself. No functional changes, in that
every platform had exactly the same implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the I/O port base isn't being set anywhere, which allows things
like generic_inl() to blow up. Fix this up to point at the PCI IO window.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCIC contains a read-only cache line size register that we can
derive pci_cache_line_size from. So, make sure that the software idea of
the cache line size actually matches the host controller's idea.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Don't use pci_write_reg() for these, as it defaults to 32-bit. Rather
than using the helper, use __raw_writeb() directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks how the host controller is probed, and makes it a bit more
verbose in the event a new type of controller is detected. Additionally,
we also log the revision information.
This now uses the proper access sizes for the vendor/device registers,
rather than relying on a larger access that encapsulated both of them.
Not all devices support 32-bit read cycles for these registers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7780 PCI host controller implements a configuration header that
requires a fair bit of hand-holding to initialize properly. By default
it appears as a pre-2.0 host controller given the zeroed out class code,
so fix this up properly.
Some boards that happened to be using the R7780RP version of the PCIC
fixups had set this correctly, but this belongs in the standard
initialization, and is by no means board specific.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
P1SEGADDR is obsolete and will be killed off completely in the future,
so transition off of it and reference P1SEG explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SE7780 has the same PCIC fixup as SDK7780, and SH7785LCR the same
as R7780RP. Switch to using those, and drop the duplicate code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With board_pci_channels now being exported in a single place, update the
boards that duplicated the export.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of sometimes exporting board_pci_channels[] in the board specific
code just export it in one place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a __get_pci_io_base() function which is used to match a port range
against struct pci_channel. This allows us to detect if a port range is
assigned to pci or happens to be legacy port io. While at it, remove unused
cpu-specific cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the code to use __is_pci_memory() instead of
is_pci_memaddr(). __is_pci_memory() loops through all the pci
channels on the system to match memory windows.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the io window base address in struct pci_channel and use that one
instead of SH77xx_PCI_IO_BASE.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store the base address of the pci host controller registers in struct
pci_channel and use the address in pci_read_reg() and pci_write_reg().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Store a struct pci_channel pointer in bus->sysdata. This makes whatever
struct pci_channel assigned to a bus available for sh4_pci_read() and
sh4_pci_write(). We also modify PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to
use bus->sysdata - this to gives us support for multiple pci channels.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replaces PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM with direct struct
pci_channel access. This allows us to have more than one pci
channel.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds an init callback to struct pci_channel and makes sure
it is initialized properly. Code is added to call this init function
from pcibios_init(). Return values are adjusted and a warning is is
printed if init fails.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patches rework the pci code for the sh architecture.
Currently each board implements some kind of ioport to address mapping.
Some boards use generic_io_base others try passing addresses as io ports.
This is the first set of patches that try to unify the pci code as much
as possible to avoid duplicated code. This will in the end lead to fewer
lines board specific code and more generic code.
This patch makes sure a struct pci_channel pointer is passed along to
various pci functions such as pci_read_reg(), pci_write_reg(),
pci_fixup_pcic(), sh7751_pcic_init() and sh7780_pcic_init().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix the cmd cache keys for amp verbs
ALSA: add missing definitions(letters) to HD-Audio.txt
ALSA: hda - Add quirk mask for Fujitsu Amilo laptops with ALC883
[ALSA] intel8x0: add one retry to the ac97_clock measurement routine
[ALSA] intel8x0: fix wrong conditions in ac97_clock measure routine
ALSA: hda - Avoid call of snd_jack_report at release
ALSA: add private_data to struct snd_jack
ALSA: snd-usb-caiaq: rename files to remove redundant information in file pathes
ALSA: snd-usb-caiaq: clean up header includes
ALSA: sound/pci: use memdup_user()
ALSA: sound/usb: use memdup_user()
ALSA: sound/isa: use memdup_user()
ALSA: sound/core: use memdup_user()
[ALSA] intel8x0: do not use zero value from PICB register
[ALSA] intel8x0: an attempt to make ac97_clock measurement more reliable
[ALSA] pcm-midlevel: Add more strict buffer position checks based on jiffies
[ALSA] hda_intel: fix unexpected ring buffer positions
ASoC: Disable S3C64xx support in Kconfig
ASoC: magician: remove un-necessary #include of pxa-regs.h and hardware.h
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (28 commits)
cfq-iosched: add close cooperator code
cfq-iosched: log responsible 'cfqq' in idle timer arm
cfq-iosched: tweak kick logic a bit more
cfq-iosched: no need to save interrupts in cfq_kick_queue()
brd: fix cacheflushing
brd: support barriers
swap: Remove code handling bio_alloc failure with __GFP_WAIT
gfs2: Remove code handling bio_alloc failure with __GFP_WAIT
ext4: Remove code handling bio_alloc failure with __GFP_WAIT
dio: Remove code handling bio_alloc failure with __GFP_WAIT
block: Remove code handling bio_alloc failure with __GFP_WAIT
bio: add documentation to bio_alloc()
splice: add helpers for locking pipe inode
splice: remove generic_file_splice_write_nolock()
ocfs2: fix i_mutex locking in ocfs2_splice_to_file()
splice: fix i_mutex locking in generic_splice_write()
splice: remove i_mutex locking in splice_from_pipe()
splice: split up __splice_from_pipe()
block: fix SG_IO to return a proper error value
cfq-iosched: don't delay queue kick for a merged request
...
Fix the key value generation for get/set amp verbs. The upper bits of
the parameter have to be combined with the verb value to be unique for
each direction/index of amp access.
This fixes the resume problem on some hardwares like Macbook after
the channel mode is changed.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: pseries/dtl.c should include asm/firmware.h
powerpc: Fix data-corrupting bug in __futex_atomic_op
powerpc/pseries: Set error_state to pci_channel_io_normal in eeh_report_reset()
powerpc: Allow 256kB pages with SHMEM
powerpc: Document new FSL I2C bindings and cleanup
powerpc/mm: Fix compile warning
powerpc/85xx: TQM8548: update defconfig
powerpc/85xx: TQM8548: use proper phy-handles for enet2 and enet3
powerpc/85xx: TQM85xx: correct address of LM75 I2C device nodes
powerpc: Add support for early tlbilx opcode
powerpc: Fix tlbilx opcode
It turns out that 'smp_call_function_many()' doesn't work at all like
'smp_call_function_single()', and my change to Andrew's patch to use it
rather than a loop over all CPU's acpi-cpufreq doesn't work.
My bad.
'smp_call_function_many()' has two "features" (aka "documented bugs"):
(a) it needs to be called with preemption disabled, because it uses
smp_processor_id() without guarding the CPU lookup with 'get_cpu()'
and 'put_cpu()' like the 'single' variant does.
(b) even if the current CPU is part of the CPU mask, it won't do the
call on that CPU.
Still, we're better off trying to use 'smp_call_function_many()' than
looping over CPU's, since it at least in theory allows us to use a
broadcast IPI and do it all in parallel. So let's just work around the
silly semantic bugs in that function.
Reported-and-tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have processes that are working in close proximity to each
other on disk, we don't want to idle wait. Instead allow the close
process to issue a request, getting better aggregate bandwidth.
The anticipatory scheduler has similar checks, noop and deadline do
not need it since they don't care about process <-> io mappings.
The code for CFQ is a little more involved though, since we split
request queues into per-process contexts.
This fixes a performance problem with eg dump(8), since it uses
several processes in some silly attempt to speed IO up. Even if
dump(8) isn't really a valid case (it should be fixed by using
CLONE_IO), there are other cases where we see close processes
and where idling ends up hurting performance.
Credit goes to Jeff Moyer <jmoyer@redhat.com> for writing the
initial implementation.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We only kick the dispatch for an idling queue, if we think it's a
(somewhat) fully merged request. Also allow a kick if we have other
busy queues in the system, since we don't want to risk waiting for
a potential merge in that case. It's better to get some work done and
proceed.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's called from the workqueue handlers from process context, so
we always have irqs enabled when entered.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
brd is missing a flush_dcache_page. On 2nd thoughts, perhaps it is the
pagecache's responsibility to flush user virtual aliases (the driver of
course should flush kernel virtual mappings)... but anyway, there
already exists cache flushing for one direction of transfer, so we
should add the other.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
brd is always ordered (not that it matters, as it is defined not to
survive when the system goes down). So tell the block layer it is
ordered, which might be of help with testing filesystems.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Explain that with __GFP_WAIT set it will not fail, and that the caller
must never allocate more than 1 bio at the time.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are lots of sequences like this, especially in splice code:
if (pipe->inode)
mutex_lock(&pipe->inode->i_mutex);
/* do something */
if (pipe->inode)
mutex_unlock(&pipe->inode->i_mutex);
so introduce helpers which do the conditional locking and unlocking.
Also replace the inode_double_lock() call with a pipe_double_lock()
helper to avoid spreading the use of this functionality beyond the
pipe code.
This patch is just a cleanup, and should cause no behavioral changes.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove the now unused generic_file_splice_write_nolock() function.
It's conceptually broken anyway, because splice may need to wait for
pipe events so holding locks across the whole operation is wrong.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Rearrange locking of i_mutex on destination and call to
ocfs2_rw_lock() so locks are only held while buffers are copied with
the pipe_to_file() actor, and not while waiting for more data on the
pipe.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Rearrange locking of i_mutex on destination so it's only held while
buffers are copied with the pipe_to_file() actor, and not while
waiting for more data on the pipe.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
splice_from_pipe() is only called from two places:
- generic_splice_sendpage()
- splice_write_null()
Neither of these require i_mutex to be taken on the destination inode.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Split up __splice_from_pipe() into four helper functions:
splice_from_pipe_begin()
splice_from_pipe_next()
splice_from_pipe_feed()
splice_from_pipe_end()
splice_from_pipe_next() will wait (if necessary) for more buffers to
be added to the pipe. splice_from_pipe_feed() will feed the buffers
to the supplied actor and return when there's no more data available
(or if all of the requested data has been copied).
This is necessary so that implementations can do locking around the
non-waiting splice_from_pipe_feed().
This patch should not cause any change in behavior.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
