Without cipher part nullify of TXRX_CSR0 register we can receive
corrupted frames (removed IV or IVC), after reloading rt2500usb module
with nohwcrypt=1 option, if previous some keys were configured into
the hardware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rt2500usb hardware encryption broken by commit
96b61bafe2
"rt2x00: Clean up USB vendor request buffer functions"
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
base index is not used anymore and so remove it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
This patch restores the ability to set msglvl through ethtool.
The issue was introduced by:
commit 675ad47375
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_terminate_urbs() uses schedule_timeout() with argument 3 msecs.
schedule_timeout() uses jiffies as argument, so convert msecs to jiffies
with msecs_to_jiffies().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the code which disables 100Mbps advertising when
the ks8842 is accessed via timberdale.
At higher speed it's good to be nice to the internal state machine
of timberdale by acking interrupts. That is done by a write to the
interrupt ack register (IAR).
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snprintf() returns the number of bytes that would have been written. It
can be larger than the size of the buffer. The current code won't
overflow, but people cut and paste this stuff so lets do it right and
also make the static checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a reset the MDICNFG.Destination and MDICNFG.COM_MDIO
register fields are not restored to the EEPROM default.
This patch modifies the reset code to read the EEPROM
and restore the default values.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for external MDIO PHYs, in addition to
the standard SFP support for SGMII PHYs over the I2C interface.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
err is set again a few lines below.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch 9e39f7c5b3 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:
s2io: eth6: Next block at: c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove #define PFX
Improve a couple of loops to avoid deep indentation.
Compile tested only
$ size drivers/net/qla3xxx.o.*
text data bss dec hex filename
51603 212 13864 65679 1008f drivers/net/qla3xxx.o.old
50413 212 13864 64489 fbe9 drivers/net/qla3xxx.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit:
commit f1aa4c541e
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Tue Jun 29 21:38:55 2010 +0200
rt2x00: Write the BSSID to register when interface is added
mananged mode in rt2500pci was broken, due to intf->bssid containing
random data rather then the expected 00:00:00:00:00:00
This is corrected by sending the BSSID to rt2x00lib_config_intf
only in AP mode where the bssid is set to a valid value.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the noisefloor array, the extension channel values start at index 3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Negate has precedence over comparison so the original test was always
false. (Neither 0 nor 1 are equal to NL80211_IFTYPE_MONITOR).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes txq state(txq->stopped) can be marked as started but the actual
queue may not be started (in ATH_WIPHY_SCAN state, for example). Fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
snprintf() returns the number of characters that would have been written
(not counting the NUL character). So we can't use it as the limiter to
simple_read_from_buffer() without capping it first at sizeof(buf).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current practice of checking vif for NULL in one place but not
another seems to confuse some static checkers, smatch in particular.
Since vif will only be NULL in the case of internal scans, adjust the
checks accordingly.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/rtl818x/rtl8180_rtl8225.c
drivers/net/wireless/rtl818x/rtl8180_rtl8225.c:53:33: warning: dubious: x | !y
The existing code is clever and works fine, but it's not worth even a
single line of Sparse warning SPAM...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/wl12xx/wl1251_tx.c
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: expected unsigned short [unsigned] [usertype] frag_threshold
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: expected unsigned short [unsigned] [usertype] length
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: expected unsigned short [unsigned] [usertype] rate
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: expected unsigned int [unsigned] [usertype] expiry_time
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: expected restricted __le16 [usertype] fc
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: got unsigned short [unsigned] [assigned] [usertype] fc
CHECK drivers/net/wireless/wl12xx/wl1251_cmd.c
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: expected unsigned int [unsigned] [usertype] rx_config_options
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: expected unsigned int [unsigned] [usertype] rx_filter_options
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: expected unsigned short [unsigned] [usertype] tx_rate
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: expected unsigned int [unsigned] [usertype] min_duration
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: expected unsigned int [unsigned] [usertype] max_duration
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: got restricted __le32 [usertype] <noident>
CHECK drivers/net/wireless/wl12xx/wl1251_boot.c
drivers/net/wireless/wl12xx/wl1251_boot.c:228:22: warning: symbol 'interrupt' shadows an earlier one
/home/linville/git/wireless-next-2.6/arch/x86/include/asm/hw_irq.h:132:13: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlagn: add statistic notification structure for WiFi/BT devices" added
several new '__attribute__ ((packed))' lines. Change them to the
generic __packed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
This is found to address "BUG at arch/x86/mm/physaddr.c:5"
as described here:
http://lkml.org/lkml/2010/7/14/21
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: drivers/net/built-in.o(.data+0x24): Section mismatch in reference from
the variable dec_lance_tc_driver to the function .init.text:dec_lance_tc_probe()
The variable dec_lance_tc_driver references
the function __init dec_lance_tc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing this one results in a new mismatch:
WARNING: drivers/net/built-in.o(.devinit.text+0x14): Section mismatch in reference from the function dec_lance_tc_probe() to the function .init.text:dec_lance_probe()
The function __devinit dec_lance_tc_probe() references
a function __init dec_lance_probe().
If dec_lance_probe is only used by dec_lance_tc_probe then
annotate dec_lance_probe with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The macros for the values of the bit field describing the four
different versions of statistics supported by different hardware
variants were being misused. Where the code was trying to test if the
hardware implements V3, it was actually testing whether it implements
any of V1, V2, or V3, causing the driver to report statistics that
don't really exist in the hardware, with bogus values.
Signed-off-by: Mike Ditto <mditto@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an overflow bug in vmxnet3 Tx descriptor
This patch fixes a bug where a 16K buffer on a Tx descriptor was overflowing
into the 'gen' bit in the descriptor thereby corrupting the descriptor and
stalling the transmit ring.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Matthew Delco <delcoM@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds wrappers for ethtool to get or set wake-on-LAN
setting without re-inserting the kernel module.
Signed-off-by: Andrew O. Shadoura <andrew@beldisplaytech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_attach missing from error path in qlcnic_diag_alloc_res
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback not supported for virtual function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are still some LRO cards that cause GSO errors in tun,
and BUG on this is an unfriendly way to tell the admin
to disable LRO.
Further, experience shows we might have more GSO bugs lurking.
See https://bugzilla.kernel.org/show_bug.cgi?id=16413
as a recent example.
dumping a packet will make it easier to figure it out.
Replace BUG with warning+dump+drop the packet to make
GSO errors in tun less critical and easier to debug.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Alex Unigovsky <unik@compot.ru>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest changes about 64bit stats on 32bit arches,
[commit 28172739f0 (net: fix 64 bit counters on 32 bit arches)],
I missed ixgbe uses a bit of magic in its ixgbe_gstrings_stats
definition.
IXGBE_NETDEV_STAT() must now assume offsets relative to
rtnl_link_stats64, not relative do dev->stats.
As a bonus, we also get 64bit stats on ethtool -S
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix maximum and minmum bandwith value.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After:
commit 6146b1a4da
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Tue Nov 4 17:51:15 2008 -0800
bonding: Fix ALB mode to balance traffic on VLANs
the dev field in the RLB ARP packet handler was set to NULL to wildcard
and accommodate balancing VLANs on top of bonds.
This has the side-effect of the packet handler being called against
other, non RLB-enabled bonds, and a kernel oops results when it tries to
dereference rx_hashtbl in rlb_update_entry_from_arp(), which won't be
set for those bonds, e.g. active-backup.
With the __netif_receive_skb() changes from:
commit 1f3c8804ac
Author: Andy Gospodarek <andy@greyhouse.net>
Date: Mon Dec 14 10:48:58 2009 +0000
bonding: allow arp_ip_targets on separate vlans to use arp validation
frames received on VLANs correctly make their way to the bond's handler,
so we no longer need to wildcard the device.
The oops can be reproduced by:
modprobe bonding
echo active-backup > /sys/class/net/bond0/bonding/mode
echo 100 > /sys/class/net/bond0/bonding/miimon
ifconfig bond0 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth0 > /sys/class/net/bond0/bonding/slaves
echo +eth1 > /sys/class/net/bond0/bonding/slaves
echo +bond1 > /sys/class/net/bonding_masters
echo balance-alb > /sys/class/net/bond1/bonding/mode
echo 100 > /sys/class/net/bond1/bonding/miimon
ifconfig bond1 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth2 > /sys/class/net/bond1/bonding/slaves
echo +eth3 > /sys/class/net/bond1/bonding/slaves
Pass some traffic on bond0. Boom.
[ Tested, behaves as advertised. I do not believe a test of the bonding
mode is necessary, as there is no race between the packet handler and
the bonding mode changing (the mode can only change when the device is
closed). Also updated the log message to include the reproduction and
full commit ids. -J ]
Signed-off-by: Greg Edwards <greg.edwards@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a095cfc40e
"3c59x: Specify window explicitly for access to windowed registers"
changed the first parameter to mdio_sync(), from a pointer to the
register mapping, to a pointer to the vortex_private structure,
and changed all but one of the call sites. Fix that last one.
Reported-by: Luca Falavigna <dktrkranz@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
vpd_data[] is allocated as kmalloc(256, GFP_KERNEL), so if cnt = 255
then (cnt + 3) overflows 256. memset() is executed without checking.
vpd_data[cnt+2] must be less than 256-cnt-2 as the latter is number of
vpd_data[] elements to copy.
Do not fill with zero the beginning of nic->serial_num as it will
be filled with vpd_data[].
String in product_name[] should be terminated by '\0'.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume that "pd" can be null on the previous line, and throughout the
function so we should check it here as well. This was introduced by
9b2c2ff7a1 "mv643xx_eth: use sw csum for big packets"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vortex_probe1() fails we should unmap ioaddr mapped earlier.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Corey Thomas <coreythomas@charter.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes names of some variables.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a virtual function driver in initialized, the network mac
query command can fail. Skip display of error message in that case.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a mac address has not been configured for a VF,
there is no need to call be_cmd_pmac_del.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
defines shouldn't be terminated with a
semicolon, the code using them should
supply it. Luckily these are not used
in a context where it matters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the ibss_beacon variable will only be
filled in the appropriate modes, there's no
reason to be checking the mode again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some devices may have multiple MAC
addresses in their EEPROM, read them
and advertise them to cfg80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is only needed in the same
file it is defined in, i.e. iwl-core.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
gcc complains about the firmware loading:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:1860: warning: ‘tlv_len’ may be used uninitialized in this function
iwl-agn.c:1861: warning: ‘tlv_type’ may be used uninitialized in this function
iwl-agn.c:1862: warning: ‘tlv_data’ may be used uninitialized in this function
This is almost correct but we do do break out of the TLV
parsing loop when setting ret. However, the code is hard
to follow, and clearly even the compiler is having issues
with it too.
Additionally, however, the current code is wrong. If there
is a TLV length check error, the code will report
invalid TLV after parsing: ...
because "len" will still be non-zero as we broke out of
the loop.
So to remove the warning and fix that issue, make the code
easier to read by doing length checking with an error label.
As a result, we can completely remove the "ret" variable.
Also, while at it, remove the "fixed_tlv_size" variable
since each TLV type has its own specified length, it just
happens that we have only variable length, flags (0 length)
and u32 TLVs right now. It should still be checked with more
explicit length checks to make it easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Different devices have different size of phy calibration table; add
new TLV to specify the size. If the TLV is not part of uCode header, the
default table size will be used to make sure the backward
compatibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WiFi/BT combo devices has different statistics notification
structure, adding the support here to make sure the structure
align correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Only WiFi/BT combo devices need to use bluetooth version of statistics
notification; adding the flag in .cfg file to indicate the need for
using different data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If its WiFi/BT combo device, the statistics notification sent by
uCode will include the additional BT related statistics counters.
Adding new data structure to support the new layout.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If the allocations fail in either dwmac1000_setup() or dwmac100_setup()
then return NULL. These are called from stmmac_mac_device_setup(). The
check for NULL returns in stmmac_mac_device_setup() needed to be moved
forward a couple lines.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying VLAN information to or removing from a slave
during slave addition or removal, the bonding code currently holds
the bond->lock for write to prevent concurrent modification of the
vlan_list / vlgrp.
This is unnecessary, as all of these operations occur under
RTNL. Holding the bond->lock also caused might_sleep issues for
some drivers' ndo_vlan_* functions. This patch removes the extra
locking.
Problem reported by Michael Chan <mchan@broadcom.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ad1afb0039
("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
it is now regular practice for a VLAN "add vid" for VLAN 0 to
arrive prior to any VLAN registration or creation of a vlan_group.
This patch updates the bonding code that tests for the presence
of VLANs configured above bonding. The new logic tests for bond->vlgrp
to determine if a registration has occured, instead of testing that
bonding's internal vlan_list is empty.
The old code would panic when vlan_list was not empty, but
vlgrp was still NULL (because only an "add vid" for VLAN 0 had occured).
Bonding still adds VLAN 0 to its internal list so that 802.1p
frames are handled correctly on transmit when non-VLAN accelerated
slaves are members of the bond. The test against bond->vlan_list
remains in bond_dev_queue_xmit for this reason.
Modification to the bond->vlgrp now occurs under lock (in
addition to RTNL), because not all inspections of it occur under RTNL.
Additionally, because 8021q will never issue a "kill vid" for
VLAN 0, there is now logic in bond_uninit to release any remaining
entries from vlan_list.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Pedro Garcia <pedro.netdev@dondevamos.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the change from mdio polling to irq, it became necessary to
restore the interrupt mask after resetting the chip in fec_stop().
Otherwise, with all irqs disabled, no communication with the PHY will be
possible after e.g. un-/replugging the cable and the device gets
stalled.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_iomap() can fail, handle this case and return -ENOMEM from probe
function.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Wagner reported OOM symptoms when sending UDP traffic over
a macvtap link to a kvm receiver.
This appears to be caused by the fact that macvtap packet queues
are unlimited in length. This means that if the receiver can't
keep up with the rate of flow, then we will hit OOM. Of course
it gets worse if the OOM killer then decides to kill the receiver.
This patch imposes a cap on the packet queue length, in the same
way as the tuntap driver, using the device TX queue length.
Please note that macvtap currently has no way of giving congestion
notification, that means the software device TX queue cannot be
used and packets will always be dropped once the macvtap driver
queue fills up.
This shouldn't be a great problem for the scenario where macvtap
is used to feed a kvm receiver, as the traffic is most likely
external in origin so congestion notification can't be applied
anyway.
Of course, if anybody decides to complain about guest-to-guest
UDP packet loss down the track, then we may have to revisit this.
Incidentally, this patch also fixes a real memory leak when
macvtap_get_queue fails.
Chris Wright noticed that for this patch to work, we need a
non-zero TX queue length. This patch includes his work to change
the default macvtap TX queue length to 500.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add and use a few neatening macros
Remove PFX
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert printk(KERN_ERR to pr_err(
$ size drivers/net/qlge/built-in.o.*
text data bss dec hex filename
116456 2312 25712 144480 23460 drivers/net/qlge/built-in.o.old
114909 2312 25728 142949 22e65 drivers/net/qlge/built-in.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ixgbe cards put an invalid VF device ID in the PCIe SR-IOV
capability. The ixgbe driver is only valid for PFs or non SR-IOV
hardware. It seems that the same problem could occur on igb hardware as
well, so if we discover we are trying to initialize a VF in ixbge_probe
or igb_probe, print an error and exit.
Based on a patch for ixgbe from Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: Chris Wright <chrisw@sous-sol.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c:111:5: warning: symbol 'b43_modparam_pio' was not declared. Should it be static?
CHECK drivers/net/wireless/b43/phy_g.c
drivers/net/wireless/b43/phy_g.c:975:56: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
CHECK drivers/net/wireless/b43/phy_lp.c
drivers/net/wireless/b43/phy_lp.c:2701:6: warning: symbol 'b43_lpphy_op_switch_analog' was not declared. Should it be static?
drivers/net/wireless/b43/phy_lp.c:1148:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1525:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1529:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
CHECK drivers/net/wireless/b43/wa.c
drivers/net/wireless/b43/wa.c:385:60: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:403:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:405:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:415:71: warning: cast truncates bits from constant value (ffff0fff becomes fff)
AFAICT, none of these amount to real bugs. But this reduces warning
spam from sparse w/o significantly affecting readability of the code (IMHO).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of own implementation of hex_to_bin().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance a module version to 1.52.53-2.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Protect statistics ramrod sending code and a statistics counter update
with a spinlock. Otherwise there was a race condition that would allow sending
a statistics ramrods with the same sequence number or with sequence numbers not
in a natural order, which would cause a FW assert.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Protect the statistics state machine state update with a
spinlock. Otherwise there was a race condition that would cause the
statistics to stay enabled despite the fact that they were disabled in
the LINK_DOWN event handler.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/vhost/net.c
net/bridge/br_device.c
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36f
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
bridge: Partially disable netpoll support
tcp: fix crash in tcp_xmit_retransmit_queue
IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())
ibmveth: lost IRQ while closing/opening device leads to service loss
rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()
vhost: avoid pr_err on condition guest can trigger
ipmr: Don't leak memory if fib lookup fails.
vhost-net: avoid flush under lock
net: fix problem in reading sock TX queue
net/core: neighbour update Oops
net: skb_tx_hash() fix relative to skb_orphan_try()
rfs: call sock_rps_record_flow() in tcp_splice_read()
xfrm: do not assume that template resolving always returns xfrms
hostap_pci: set dev->base_addr during probe
axnet_cs: use spin_lock_irqsave in ax_interrupt
dsa: Fix Kconfig dependencies.
act_nat: not all of the ICMP packets need an IP header payload
r8169: incorrect identifier for a 8168dp
Phonet: fix skb leak in pipe endpoint accept()
Bluetooth: Update sec_level/auth_type for already existing connections
...
The existing code seemed to be somewhat based on the datasheet, but
varied substantially from the vendor-provided driver. This mirrors the
handling of the rtl8185 case from that driver, but still neglects the
specifics for the rtl8180 hardware. Those details are a bit muddled...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/mwl8k.c:1541:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/mwl8k.c:1541:21: expected restricted __le16 [usertype] result
drivers/net/wireless/mwl8k.c:1541:21: got int
drivers/net/wireless/mwl8k.c:1575:42: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1575:42: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1587:50: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1587:50: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1587:50: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1592:50: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1592:50: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1592:50: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1845:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1845:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1845:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1848:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1848:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1848:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1851:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1851:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1851:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1854:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1854:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1854:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1857:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1857:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1857:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1860:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1860:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1860:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:3055:20: warning: incorrect type in assignment (different base types)
drivers/net/wireless/mwl8k.c:3055:20: expected restricted __le16 [usertype] ht_caps
drivers/net/wireless/mwl8k.c:3055:20: got unsigned short [unsigned] [usertype] cap
At least the last one looks like a real bug...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
CHECK drivers/net/wireless/rt2x00/rt2x00debug.c
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: expected restricted __le32 [usertype] chip_rev
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: got restricted __le16 [usertype] <noident>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CHECK drivers/net/wireless/ipw2x00/libipw_module.c
drivers/net/wireless/ipw2x00/libipw_module.c:65:21: warning: symbol 'libipw_config_ops' was not declared. Should it be static?
drivers/net/wireless/ipw2x00/libipw_module.c:66:6: warning: symbol 'libipw_wiphy_privid' was not declared. Should it be static?
CHECK drivers/net/wireless/ipw2x00/libipw_wx.c
drivers/net/wireless/ipw2x00/libipw_wx.c:415:17: warning: symbol 'ssid' shadows an earlier one
drivers/net/wireless/ipw2x00/libipw_wx.c:324:9: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/ipw2x00/ipw2100.c
drivers/net/wireless/ipw2x00/ipw2100.c:177:28: warning: symbol 'ipw2100_pm_qos_req' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bug in setup_sge_queues() where we were incorrectly only allocating a
single "Queue Set" for MSI mode.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error in checking for the end of the mailbox response delay
array. We ended up walking off the end and, if we were unlucky, we'd end up
pulling in a 0 and never terminate the mailbox response delay loop ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_mb() inside bnx2_tx_avail() is used twice in the normal
bnx2_start_xmit() path (see illustration below). The full memory
barrier is only necessary during race conditions with tx completion.
We can speed up the tx path by replacing smp_mb() in bnx2_tx_avail()
with a compiler barrier. The compiler barrier is to force the
compiler to fetch the tx_prod and tx_cons from memory.
In the race condition between bnx2_start_xmit() and bnx2_tx_int(),
we have the following situation:
bnx2_start_xmit() bnx2_tx_int()
if (!bnx2_tx_avail())
BUG();
...
if (!bnx2_tx_avail())
netif_tx_stop_queue(); update_tx_index();
smp_mb(); smp_mb();
if (bnx2_tx_avail()) if (netif_tx_queue_stopped() &&
netif_tx_wake_queue(); bnx2_tx_avail())
With smp_mb() removed from bnx2_tx_avail(), we need to add smp_mb() to
bnx2_start_xmit() as shown above to properly order netif_tx_stop_queue()
and bnx2_tx_avail() to check the ring index. If it is not strictly
ordered, the tx queue can be stopped forever.
This improves performance by about 5% with 2 ports running bi-directional
64-byte packets.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch by Breno Leitão <leitao@linux.vnet.ibm.com>.
Allocate the actual number of vectors and make use of fewer vectors
if pci_enable_msix() returns > 0. We must allocate one additional
vector for the cnic driver.
Cc: Breno Leitão <leitao@linux.vnet.ibm.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using the wrong tx multicast counter instead of the rx multicast
counter.
Reported-by: Peter Snellman <peter.snellman@cinnober.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version string to better reflect what is in the driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE protocol stack may hold a lock when this gets called.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FCoE is disabled, there is a race condition that FCoE offload is
turned off but the FCoE protocol driver is still queuing I/O thinking
offload support still exists. This patch toggles off corresponding FCoE
netdev feature flags and notify the FCoE stack first, allowing FCoE
protocol stack driver to update its flags upon NETDEV_FEAT_CHANGE so no
I/O will be using offload.
Also, indicate FCoE offload flags in vlan_features in ixgbe_probe once
and do not toggle them in ixgbe_fcoe_enable/disable so when FCoE is
created on the VLAN interface, vlan_transfer_features() would properly
update the VLAN netdev features flag and notify the FCoE protocol driver
for NETDEV_FEAT_CHANGE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes UDP from the supported protocols for RSS hashing. The
reason for removing this protocol is because IP fragmentation was causing a
network flow to be broken into two streams, one for fragmented, and one for
non-fragmented and this in turn was causing out-of-order issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DPF bit when PFC is enabled. This will discard
PFC frames so they do not get passed up the stack.
The DPF bit is set for flow control, but not priority
flow control this brings pfc inline with fc.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it possible to limit the number of descriptors down to 48
per ring. The reason for this change is to address a variation on hardware
errata 10 for 82546GB in which descriptors will be lost if more than 32
descriptors are fetched and the PCI-X MRBC is 512.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/82596.c: In function 'i596_open':
drivers/net/82596.c:1044: warning: label 'err_irq_dev' defined but not used
Caused by "82596: free resources on error"
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew:
drivers/net/ks8842.c: In function 'ks8842_handle_rx':
drivers/net/ks8842.c:428: warning: 'status' may be used uninitialized in this function
Just use the 32-bit status for all reads, and delete the useless
cast to 'int' when reading a u16 into 'len'.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SMP systems, the SMSC911x registers may be accessed by multiple CPUs
and this seems to put the chip in an inconsistent state. The patch adds
spinlocks to the smsc911x_reg_read, smsc911x_reg_write,
smsc911x_rx_readfifo and smsc911x_tx_writefifo functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bonding/bond_main.c:179:12: warning: ‘disable_netpoll’
defined but not used
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARCH_PNX010X doesn't exist in Kconfig, therefore removing all
references for it from the source code/Kconfig.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the interrupt type set in VM configuration.
When interrupt type is not auto, do not ignore the interrupt type set from
VM configuration.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold rtnl_lock to get the right link state.
While asynchronously resetting the device, hold rtnl_lock to get the
right value from netif_running. If a reset is scheduled, and the device
goes thru close and open, it may happen that reset and open may run in
parallel. Holding rtnl_lock will avoid this.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ad1afb0039 (vlan_dev: VLAN 0 should be treated
as "no vlan tag" (802.1p packet)),
bond_inet6addr_event() might be called with a NULL bond->vlgrp pointer, and
a non empty bond->vlan_list. vlan_group_get_device() is dereferencing a NULL pointer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
probe_irq_off() returns the first irq found or if two irqs are found
then it returns the negative of the first irq found. We can cast
dev->irq to an int so that the test for negative values works.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_get_domain_bus_and_slot: caller must decrement the
reference count by calling pci_dev_put().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change initializes the state of link at the time when driver is
loaded. The ethtool output for 'link detected' and 'link speed'
is thus valid even before the interface is brought up.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DMA API as PCI equivalents will be deprecated. This change also allow
to allocate with GFP_KERNEL in some places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"Recover from tx stall" function is available for all devices except
4965, here add the functionality to 4965.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This moves the various known Marvell PHY IDs to include/linux/marvell_phy.h
along with dev_flags definitions for use by the driver.
I then added a flag that changes the PHY init code to setup the LEDs
config to the values needed to operate a dns323 rev C1 NAS.
I moved the existing "resistance" flag to the .h as well, though I've
been unable to find whoever sets this to convert it to use that constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open. Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.
There is a window where an IRQ will be left unserviced (H_EOI will not
be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch complains that "upriv->read_urb" gets dereferenced before
checking for NULL. It turns out that it's possible for
"upriv->read_urb" to be NULL so I added checks around the dereferences.
Also I remove an "if (upriv->bap_buf != NULL)" check because
"kfree(NULL) is OK.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An A-MPDU may contain several subframes each containing its own
CRC for the data. Each subframe also has a respective CRC for the
MPDU length and 4 reserved bits (aka delimeter CRC). AR9003 will
ACK frames that have a valid data CRC but have failed to pass the
CRC for the MPDU length, if and only if the subframe is not the
last subframe in an A-MPDU and if an OFDM phy OFDM reset error has
been caught. Discarding those subframes results in packet loss under
heavy stress conditions, an example being UDP video. Since the
frames are ACK'd by hardware we need to let these frames through
and process them as valid frames.
Cc: Tushit Jain <tushit.jain@atheros.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c:441:5:
warning: symbol 'ath9k_htc_tx_aggr_oper'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
[<ffffffff8105fe59>] register_lock_class+0x152/0x31f
[<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
[<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
[<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41
[<ffffffff810628d5>] lock_acquire+0xd1/0xf7
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f136>] cancel_work_sync+0xb/0xd
[<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
[<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
[<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
[<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
[<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
[<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
[<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
[<ffffffff812ea167>] __driver_attach+0x4a/0x66
[<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
[<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
[<ffffffff812e9efd>] driver_attach+0x19/0x1b
[<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
[<ffffffff812ea41b>] driver_register+0x98/0x109
[<ffffffff813465dd>] usb_register_driver+0xb2/0x173
[<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
[<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
[<ffffffff81000203>] do_one_initcall+0x6d/0x17a
[<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
[<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix SGE resource resource deallocation bug. Forgot to increment the RXQ and
TXQ cursors in the loop ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new bit map 'intrCtrl' is introduced in the DriverShared area. The
driver should update VMXNET3_IC_DISABLE_ALL bit before writing IMR.
Signed-off-by: Ronghua Zang <ronghua@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version update
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update copyright information to reflect the Exar purchase of Neterion
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_LLTX and it's usage of local transmit locks are depricated in
favor of using the netdev queue's transmit lock. Remove the local
lock and all references to it, and use the netdev queue transmit lock
in the transmit completion handler.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error in multicast flag check, add calls to restore the status of
multicast and promiscuous mode settings after change_mtu, and style
cleanups to shorten the function calls by using a temporary variable.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove queue_state references, as they are no longer necessary.
Also, The driver needs to start/stop the queue regardless of which type
of steering is enabled. Remove checks for TX_MULTIQ_STEERING only and
start/stop for all steering types.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Signed-off-by: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'count' is unsigned. It is initialized to zero, then it can be increased
multiple times, and finally it is used in such a way:
>>>> count--;
|
| /* clear timestamp and dma mappings for remaining portion of packet */
| while (count >= 0) {
| count--;
| ...
^
If count is zero here (so, it was never increased), we would have a very
long loop :)
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_irq_byname() can return negative results, it is not seen to
unsigned irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed a bug that Mac driver does not work,because I missed the clk enable.
I have ever tested the driver when I submitted previous Mac driver patch,
and it worked good, since my bootloader has enabled the clock in advance.
But when I try to use other bootloader where clock engine was disabled,the
Mac driver does not work, so I send this patch to fix this issue.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove near duplication of format string constants by using the newly
introduced vsprintf extention %pV to reduce text by 20k or so.
$ size drivers/net/mlx4/built-in.o*
text data bss dec hex filename
161367 1866 48784 212017 33c31 drivers/net/mlx4/built-in.o
142621 1866 46248 190735 2e90f drivers/net/mlx4/built-in.o.new
Use printk_once as appropriate.
Convert printks to pr_<level>, some bare printks now use pr_cont.
Remove now unused #define PFX.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test for buffer overflow ensures we have room for 6 more bytes.
sprintf, called with %s:%d, slave->dev->name, slave->queue_id may yield
far more than 6 bytes.
The correct test is res > (PAGE_SIZE - IFNAMSIZ - 6) .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the crash kernel is loaded after crash, the device is in unknown state.
So reset the device contexts prior to its creation in case of kdump,
depending upon kernel parameter reset_devices.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap mapped IO in wd_probe1() if register_netdev() failed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o NPAR configuration which is programmed in fw, need to
restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci error recovery support added.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev notifier are not unregistered if pci_register_driver fails.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable tx timeout recovery, if auto_fw_reset is disable
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off rx pause param and autoneg param is not supported so
return error in that case.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETRAX_NETWORK_RED_ON_NO_CONNECTION doesn't exist in Kconfig, therefore
removing all references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SH_HICOSH4 doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_NAPI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_MULTICAST_REG_WRITE doesn't exist in Kconfig, therefore
removing all references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CASSINI_QGE_DEBUG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
{AR,WAVE}LAN doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few places where the sc->rxlink pointer was set to NULL "just in
case". This helps nothing - quite to the contrary it is problematic since it
can create self-linked rx descriptors in the middle of the list of receive
buffers.
Here is an example how this could happen (thanks Bob!):
cpu 0: cpu 1:
ath5k_rx_stop
ath5k_tasklet_rx
sc->rxlink = NULL; /* just in case */
// following doesn't link used
// buffer to prev.
ath5k_rxbuf_setup()
In the case of ath5k_rx_stop() and ath5k_stop_locked() buffers/descriptors are
not changed so rxlink should not be changed as well.
In ath5k_intr() we seem to try to work around a hardware bug, as the comment
(which is copied 1:1 from the HAL) suggests. I don't see how this could help.
Also the HAL does not set rxlink in this case (So where does this code come
from? It has been there since the first import of ath5k). Changed to just
increment a statistics counter.
After this patch rxlink is only set to NULL before we initialize rx descriptors
and updated when the descriptors are linked together.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a patch from Bruno Randolf, attempting useful
work while we are resetting the chip just leads to interface
lockups and bad descriptor data, and possibly DMAing to
freed buffers. Let's suspend all tasklets while
reprogramming the registers in the card to avoid such
problems.
In the future we can convert the tasklets to threaded
interrupt handlers to simplify things.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently trigger a reset via a tasklet when certain error
conditions are detected so that the card will (eventually)
restart. Unfortunately this makes locking complicated since
reset can also be called in process context (e.g. for channel
change). Currently nothing protects against concurrent resets,
which can be the source of corruption bugs.
Reset takes too long to spinlock the whole thing, so this
patch moves deferred resets into the mac80211 workqueue to
enable use of sc->lock mutex.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation, The following chip revisions were never sold:
- AR9280 v1.0
- AR9285 v1.0
- AR9285 v1.1
- AR9287 v1.0
Removing initvals specific to these chip revisions saves around 30k in
binary size (tested on MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must call del_airo_dev() before free_netdev() since we call
add_airo_dev() exactly after alloc_netdev().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the
issue of running out of buffers/descriptors in the tx path if a STA is
deleted while tx status feedback is still pending.
The remaining issue is that the skbs of the buffers are not reclaimed,
leaving a memory leak.
This patch fixes this issue by running the buffers through
ath_tx_complete_buf(), ensuring that the pending frames counter is also
updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's
never used. Remove corresponding arguments of the functions calculating
that value.
Original patch by Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b31fb86815.
pcim_*() managed drivers do not need explicit resource
releasing like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Body of the explanation:
-support 16bit and 32bit bus width.
-add device reset for ks8842/8841 Micrel device.
-set 100Mbps as a default for Micrel device.
-set MAC address in both MAC/Switch layer with different sequence for Micrel
device, as mentioned in data sheet.
-use private data to set options both 16/32bit bus width and Micrel device/
Timberdale(FPGA).
-update Kconfig in order to put more information about ks8842 device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the driver version from the driver. This version
hasn't changed since the driver's inclusion in the kernel and is a
source of confusion for some customers.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the move to phylib (commit e6b043d) I was seeing sporadic "MDIO write
timeout" messages. Measure of the actual time spent showed latency times of
more than 1600us.
This patch uses the MII event indication of the FEC hardware to detect
completion of MDIO transactions.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
xtsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQs.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jazzsonic_open() doesn't check sonic_open() return code. If it is error
we must free requested IRQ.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tc35815_init_one() fails we must unmap mapped regions.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up TX Queue Host Flow Control to cause an Egress Queue Status Update to
be generated when we run out of TX Queue Descriptors. This will, in turn,
allow us to restart a stopped TX Queue.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some of xxx_register_driver() can return error we must unregister
already registered drivers.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use spin_lock_irqsave instead of spin_lock in ax_interrupt because
the interrupt handler can also be invoked from ei_watchdog.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.
Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Large parts of the firmware initialization are shared
between rt2800pci and rt2800usb. Move this code into
rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing
interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and
thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to
TSF_SYNC_ADHOC to better express its purpose and introduce the missing
TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes
that don't need TSF merging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Activating the TBTT interrupt when a beacon interval of 0 is configured
results in an interrupt storm causing the machine to hang. Hence,
initialize the beacon interval to a reasonable default of 100TUs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the set_tim callback without managing the DTIM count and the
broad- and multicast buffering in hw, fw or the driver results in wrong
DTIM count values being sent out in beacons. Since all PCI drivers
fetch new beacons periodically and hence get an updated TIM we can just
remove the set_tim callback from these.
The rt2x00 USB drivers don't update the beacon periodically and thus
rely on the set_tim callback to get a correct TIM for beacon
transmission. USB devices still suffer from the DTIM count being wrong
under some circumstances but removing the set_tim callback from these
would cause more harm then good.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).
Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although mac80211 buffers broad- and mutlicast frames for us in AP mode
we still have to send them out after a DTIM beacon. Implement this
behavior by sending out the buffered frames when the beacondone
interrupt is processed.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all rt2x00 PCI drivers use threaded interrupts now we don't need
to schedule a work just to update the beacon. The only place where the
beacon still gets updated in atomic context is from the set_tim
callback. Hence, move the work scheduling there.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.
The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);
dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"
strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must free priv->eeprom allocated in adm8211_read_eeprom().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This test is off by one because strlen() doesn't include the NULL
terminator.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.
This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not call free_irq() if request_irq() failed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() is called both in net_close() and cleanup_card(). Since it
is requested in at1700_probe1(), leave free_irq() only in cleanup_card()
for balance.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few registers have side effects on reads, eg FIFO pointers that
auto advance or mailboxes which change ownership when read. They are
unsafe to read so exclude them from ethtool register dumps.
Bump ethtool_regs.version to indicate the changed register set.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge error.
See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_rxnfc, get_rxfh_indir, and set_rxfh_indir ethtool
methods for user manipulation of the RSS table. Besides the methods
themselves the rest of the changes here store, initialize, and write
the table contents.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two copies of some resource freeing code, turn it into
a function and call it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to settle on the kind of interrupts we'll be using, a choice that
also impacts the number of queues, before registering and making visible
the net_devices. Move the relevant code up a bit.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.112.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following checkpatch errors:
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
^
ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
^
ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);
ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 52cdf8526f,
entitled "tg3: Prevent a PCIe tx glitch". The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it. The proper place for this code is within the
device's bootcode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is coded to refuse to attach to 5717 serdes devices. Now that the
hardware is better supported, we can relax this restriction. This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets. This patch adds the missing support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt coalescing setup code used the TG3_FLG2_USING_MSIX flag to
determine whether or not to configure the rx coalescing parameters.
This is incorrect for the single MSI-X vector case. This patch changes
the code to look at the TG3_FLG3_ENABLE_RSS instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 2601d8a004. A
spectacular set of coincidences made it look as though the table was
setup incorrectly. The original version was correct.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ 56 was not freed anywhere (neither in i596_open() on error nor in
i596_close()), rx_bufs were not freed if init_i596_mem() fails,
netif_stop_queue() was not called.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_alloc_skb() failed then free already allocated skbs.
remove_rx_bufs() can be called multiple times, so set rbd->skb to NULL
to avoid double free. remove_rx_bufs() was moved upwards to be seen by
init_rx_bufs().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is loaded in guest OS, the pci variables is_virtfn and is_physfn are
both set to 0. This change uses registers in controller to determine the same.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
