mdiobus resources must be released on exit
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael reported that p54* never really entered power
save mode, even tough it was enabled.
It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...
Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids a NULL pointer dereference as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=625889
When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL. So, we need to check the return value and avoid dereferencing it
in that case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>
pcnet_cs:
add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 886275ce41 (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:
~# modprobe libertas_sdio
[ 62.315124] libertas_sdio: Libertas SDIO driver
[ 62.319976] libertas_sdio: Copyright Pierre Ossman
[ 63.020629] DMA misaligned error with device 48
[ 63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
[ 66.005035] libertas: command 0x0003 timed out
[ 66.009826] libertas: Timeout submitting command 0x0003
[ 66.016296] libertas: PREP_CMD: command 0x0003 failed: -110
Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Qlge is freeing the buffers before stopping the card DMA, and
this can cause some severe error, as a EEH event on PPC.
This patch just stop the card and then free the resources.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc
complain:
drivers/net/pxa168_eth.c:657: warning:
cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function changed recently. It now takes a struct
ifreq pointer directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple issues here:
* Some resources weren't released.
* If alloc_etherdev() failed it would have caused a NULL dereference
because "pep" would be null when we checked "if (pep->clk)".
* Also it's better to propagate the error codes from mdiobus_register()
instead of just returning -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"pep->pd" isn't checked consistently in this function. For example it's
dereferenced unconditionally on the next line after the end of the if
condition. This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this error on an s390 allyesconfig build:
linux-2.6/drivers/net/caif/caif_spi.c:98:
undefined reference to `dma_free_coherent'
Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.
The fix is pretty straightforward. This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt. If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function netxen_intr has pointer to nx_host_sds_ring
as second parameter not pointer to netxen_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Bruce Allan <bruce.w.allan@intel.com>
The alternate MAC address feature is only supported by 80003ES2LAN and
82571 LOMs as well as a couple 82571 mezzanine cards. Checking for an
alternate MAC address on other parts can fail leading to the driver not
able to load. This patch limits the check for an alternate MAC address
to be done only for parts that support the feature.
This issue has been around since support for the feature was introduced
to the e1000e driver in 2.6.34.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Fabio Varesano <fax8@users.sourceforge.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the e1000-devel mailing list, Nils Faerber reported latency issues with
the 82573 LOM on a ThinkPad X60. It was found to be caused by ASPM L1;
disabling it resolves the latency. The issue is present in kernels back
to 2.6.34 and possibly 2.6.33.
Reported-by: Nils Faerber <nils.faerber@kernelconcepts.de>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions ll_temac_rx_irq and ll_temac_tx_irq
have pointer to net_device as second parameter not
pointer to temac_local.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: Fix synchronization between HW and SW send queue
When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.
This patch detects such loss of synchronization, and resets the ehea
port when needed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.52.53-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 5000 series of devices, use long monitor timer to check
stuck tx queues.
This modification apply to all the 5000 series including 5300 and others.
Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c96c31e499
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case. Restore the original case.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applying the filter flags directly as done since
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke 3945 under some unknown circumstances, as
reported by Alex.
Since I want to keep the direct application of
filter flags on iwlagn, duplicate the code into
both 3945 and agn and remove committing the
RXON that broke things from the 3945 version.
Cc: stable@kernel.org [2.6.35]
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 5000 and 6000g2b series of devices, use long monitor timer to check
stuck tx queues.
.6000g2b series device, it is WiFi/BT combo device, there are some cases,
tx queues are not move for a period of time because the WiFi/BT coex.
.5000 series device, it is being reported firmware got reload more
often than necessary, so extend the timer to avoid un-necessary reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change the name for monitor timer, also adding define for long monitor
timer; long monitor timer can be used for the type of devices require longer
time to determine the uCode is stuck on tx and needed reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the firmware loading properly
for device ID 7015.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use appropriate command (CMD_TRIGGER_SCAN_TO) instead of scan command
(CMD_SCAN) to configure trigger scan timeout.
This was broken in commit 3a98c30f3e.
This fix address the bug reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=16554
Cc: stable@kernel.org
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The setting of SPI_DATA_POS depending on CONFIG_CAIF_SPI_SYNC
where inverted.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes rx_submit() return an error code, and makes some call sites
that care check the return value. This is important because it lets us properly
handle cases where the device isn't ready to handle URB submissions (e.g., when
it is autosuspended under some drivers); previously, we would attempt and fail
to submit URBs and reschedule ourselves to try and fail again. This patch is
against Linus's 2.6 repo commit 45d7f32c7a.
Signed-Off-By: Elizabeth Jones <ellyjones@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks. I allocated them with kcalloc()
instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov