Because repeatedly typing mSamplesPerSymbol is giving me
carpal tunnel syndrome. Replace with the much shorter,
easier to type, and just as clear name of 'sps'.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
Remove the built time resampling selection and link both options.
Move the normal push/pullBuffer() calls back to the base class and
overload them in the inherited resampling class.
USRP2/N2xx devices are the only devices that require resampling so
return that resampling is necessary on the device open(), which is
the point at which the device type will be known.
The GSM transceiver only operates at a whole number multiple of
the GSM rate and doesn't care about the actual device rate and
if resampling is used. Therefore GSM specific portion of the
transceiver should only need to submit the samples-per-symbol
value to the device interface.
Then, the device should be able to determine the appropriate
sample rate (400 ksps or 270.833 ksps) and if resampling is
appropriate.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
The transceiver only uses a single integer oversampling value,
which is more simply referred to as samples-per-symbol.
mRadioOversampling --> mSPS
mTransceiverOversampling (removed)
Signed-off-by: Thomas Tsou <tom@tsou.cc>
Periodic timing alignment should never be required for UHD devices,
though the mechanism was used as a fallback mechanism should UHD
not properly recover after an underrun - as may occur in old
003.003.000 based revisions. This issue is not a concern in more
recent UHD releases and deprecates this code for legacy USRP1
use only.
Signed-off-by: Thomas Tsou <tom@tsou.cc>
UHD device type was previously detected, but only categorized in
terms of bus type, USB or Ethernet, and sample rate capability.
With the number of supported device increasing, we can no longer
easily group devices since we need to handle more and more
device-specific peculiarities. Some of these factors are managed
internally by the UHD driver, but other factors (e.g. timing
offsets) are specific to a single device.
Start by maintaining an enumerated list of relevant device types
that we can use for applying device specific operations. Also
rename the USB/Ethernet grouping to transmit window type because
that's what it is.
enum uhd_dev_type {
USRP1,
USRP2,
B100,
NUM_USRP_TYPES,
};
Signed-off-by: Thomas Tsou <tom@tsou.cc>
With the introduction of the B100, there is USB support
using UHD devices. The characteristics of the trasmit
side burst submissions are more reflective of the bus
type than the device or driver.
Use a fixed latency interval for network devices and the
adaptive underrun approach for USB devices - regardless
of driver or device type.
The GPMC based transport on the E100 appears unaffected
by either latency scheme, which defaults to network.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2677 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Move push and pull of buffers into a dedicated file. This will
allow us to swap out resampling, non-resampling, and possibly
floating point device interfaces while presenting a single
floating point abstration in the interface itself.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2670 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Remove radio clock and vector interfaces into their own
files. This clears up and simplifies the radio interface
and, additionaly, prepares for a further split of the I/O
portion for optional resampler use.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2669 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Commit e161523c (transceiver: simplify transmit power control)
changed transmit gain control to RF setting only. This was
appropriate for a WBX board with 25 dB of gain control, but
inappropriate for an RFX with fixed transmit gain.
RFX boards will regain the ability to set transmit
attenuation. Since gain is set on the RF side first,
reintroducing digital gain settings should have limited
overall effect on non-RFX daughterboards.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2660 19bc5d8c-e614-43d4-8b26-e1612bc8e597
UHD will internally accept floats with a range of +/-1.0,
which corresponds to a 16-bit signed integer range of
apporximately +/- 32000. Set the default amplitude to .3,
which is a safe value agaist saturation elsewhere in the
transmit chain.
The non-UHD maximum amplitude is unchanged at 13500.
Remove digital gain control because it's unnecessary and
causes extra load on enbedded systems.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2654 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Push the ability to set thread priority out to the 52M
Transceiver interface, because that's where the thread
control exists.
Signed-off-by: Thomas Tsou <ttsou@vt.edu>
git-svn-id: http://wush.net/svn/range/software/public/openbts/trunk@2644 19bc5d8c-e614-43d4-8b26-e1612bc8e597
Thomas Tsou