we've added the modifier to configure Amarisoft eNB channel
model. This patch enables it for srsENB.
Change-Id: I30e65d0431b2d2792986128287caf8b23a22b2c1
Power ramping features were implemented recently for osmo-bts-trx. We
don't want to enable them because it makes phones take longer (if even
at all) to find the network.
Change-Id: I35e2f560b28eddef886ad3b2f8ffb4ff79be77da
this gives higher UL throughput because less resources are reserved for
SR/CQI. For more users we may have to make the value configurable again.
Change-Id: If6c313a1deafffda26e9effeb807ca71064c46bc
we use the otherwise unused QCI 8 as a slightly modified
version of QCI 7 (default RLC UM) with a PDCP discard
timer set to infinity to avoid dropping PDCP SDUs if
packets arive faster than can be processed in the DL
Change-Id: I06b7b583701f90827fba36564f969b5d58c9b9ad
same as for srsEPC this is also required for Amarisoft MME and eNB to support, i.e. 001/01
Note that the 3 digit MNC isn't covered by this.
Change-Id: I80a84e01ec9530c285634452d7c18c17bdd595ce
srsEPC expect zero-padding MNC/MCC in config file. However,
001 and mcc will end up as 1 in the rendered template.
Therefore, they need to be formatted correctly.
Change-Id: Ie63cd1b15b961e493a6dcbd7e5a4fbabe0bb6f33
the default value of 60s is too long to trigger errors in the handling
of this timer. So a 5s timer is more likely to reveal potential issues
during the test execution
Change-Id: Id7a6739487c7875c4f26a47d05978c9ea9f33873
we need to make the rf_port a param in the cell list because for CA with
two cells on different EARFNCs, the RF port is different
for two cells without CA on the same EARFCN the RF port is the same
so we need to be able to configure it
Change-Id: I32e83cc34811588757104c5ce1cae7277402addd
The B200 device being used in the physical setup doesn't support several
RF ports, so let's hardcode it to 0 for now.
Change-Id: Id4c31be2bd0c75f469e2293ade011c7b7ceedb1c
this allows to optionally specify a the GTP bind_address for a enb object
in the resources.conf
this address is then used for binding the listening socket for gtp connections
which, in turn, allows to run the enb and epc on the same host.
when gtp_bind_addr is not specified, addr is used by default
this is especially useful if eNB and EPC run on the same host
and ZMQ is used for RF between eNB and UE. Two eNB addresses
are needed in this case, one bind address and one "remote-accessable"
address for the UEs ZMQ radio to connect to
Change-Id: I4fe38f31401428ed3e74e1d0b64960f0af122d37
Use the ifup script to set up the netns + configure the tun device
created by lteue. Use it also as a hook to know when the UE is attached.
Since tun setup is done by arch-optimized lte-avx(2) binaries, we also
need to give capabilitites to them (instead of allowing inheritance of
caps in general in the setcap script).
Change-Id: I1e228b1296eac8e4cb183c2faa735b0468abe124
the Amarisoft UE seems to be only working with UHD when the bandwidth
param is provided. It seems the set_bandwidth() API is used.
Change-Id: I3f20a5a8ca80c63374f0ad500fd2794e2dc45479
this commit adds basic support for configuring measurements in the
eNB config. It currently support A1, A2, and A3 events.
By default UE measurements are turned off and need to be enabled by
configuring an event with:
+mod-enb-meas-event@{name},{report_type},{value},{hysterisis},{time to trigger}
For example one can update the a2 and a3 event with:
+mod-enb-meas-event@a2,rsrq,-40,2,480+mod-enb-meas-event@a3,rsrp,6,1,512
Change-Id: Ia7657be2396886840570bc41645450a268b4cfff
the num_carriers is parsed as a string in the conf dict and therefore
needs to converted to int before matching
also changed the num_carriers to be of type UINT
Change-Id: I1386812d32e1181ba666720bbb875bf9bbce0f51
the num_cells modifier allows to create multiple cells in a single enb
both cells are by default configured for CA
Change-Id: Ie9f16ce06ee56002c01097f2d338278f09ea4337
* Since license_server_addr logic is generic among all amarisoft
software, let's move it to its own config category "amarisoft", which
all amarisoft classes (amarisoft_{enb,epc}.py as of now) will import
during configure().
* The license server is disabled by default (value 0.0.0.0) since the
usual case is to have a license in the local system.
* the license server can be enabled using scenario
cfg-amarisoft-license@A.B.C.D where A.B.C.D is the address to use.
Change-Id: Id5456ad9497e91370857b80ff9a389111d3611ff
* A new abstract generic base class EPC is created
* srsEPC and AmarisoftEPC inherit from that class
* options are loaded from defaults.conf in cascade. First generic "epc",
afterwards the specific enb type.
* A new scenario is added to select the EPC type to use. srsEPC is the
default unless stated by an scenario.
* AmarisoftEPC delegates setup of the tun IP address to an "ifup"
script. As a result, since we run without root permissions (ony with
CAP_NET_ADMIN), the ifup script itself is unablet o set the IP
address. To solve this, we introduce a new osmo-gsm-tester helper
script which must be installed in the slave node which can be called
through sudo to increase privileges to do so.
With this commit, I can already get srsUE<->amarisoftENB<->amarisoftEPC
to pass ping and iperf3 4g tests.
Change-Id: Ia50ea6a74b63b2d688c8d683aea11416ad40a6d3
* object class expects the amarisoft software to be placed in directory
provided by env var AMARISOFT_PATH_ENB. On local runs, it will run the
software from there. On remote runs it will copy over that directory to
the slave.
* Configuration provided works with 6 PRBs, but probably won't work for
other values (yet).
* ZMQ support not yet available, only UHD.
One can select the Amarisoft ENB by declaring it in resources.conf:
"""
- label: AmarisoftENB-B200
type: amarisoftenb
rf_dev_type: uhd
rf_dev_args: "type=b200,serial=317B9FE,recv_frame_size=9232,send_frame_size=9232"
remote_user: jenkins
addr: 10.12.1.206
"""
And running:
"""
$ export AMARISOFT_PATH_ENB=/path/to/binaries
$ osmo-gsm-tester.py ... -s 4g:amarisoftenb-rftype@uhd+srsue-rftype@UHD+mod-enb-nprb@6 -t ping
"""
Change-Id: I1ddf4962ea6438ad977382ab201b724028ca46b3
this is needed to support the upcoming multi-cell feature in srsENB.
It's required for carrier aggregation (CA) but can also
be used for (currently) two independent 4G cells.
This commit adds baseline support for the parameter. Upcoming
commits will add hooks to configure the cell's EARFCN, etc.
Change-Id: I6d1658bf820163aee03b64b0f4ac68046c243f37
this allows to specify a fixed APN address for each subscriber in the
HLR. If the param is not provided in the resources config, the default
allocation type is used, which is to dynamically allocate an IP in the
supported range.
Change-Id: Ie6fcd7987dc7bc62a686bee3a10c67e3dd813419
Take the change to fix several small things and support recording pcap
in srsENB.
pcap generation can be enabled with scenario cfg-srs-enable-pcap.
Change-Id: Ia096a9be7efb2123f95115c751e2402fb4fec935
Those two BTS backends never had their own MS Power Control Loop, so
they should be using the "osmo" common one. This wrong value "dsp" used
to be accepted for no good reason, but it's no longer the case. Let's
remove the line to let the backend take the default one (osmo).
Change-Id: I842fce2b8185c53d1684747afcfc3ae8fba1afee
WARNING: Invalid PRACH configuration - prach=(2, 8) does not fit into the eNB PRBs=(0, 6).
Consider changing the "prach_freq_offset" value to 0 in the sib.conf file when using 6 PRBs.
Change-Id: Ie4374faca62a4d0289f78674eadec7eb5d045dfd
Latest ENB config file grammar changed and needs to be updated to work
with next versions of srsENB.
Change-Id: I84db30dc57ea9e0b05208fa86d88d42d492b237f
Before this patch, only virtual RF through ZeroMQ was supported.
This patch allows configuring srsUE and srsENB to use a real SDR with
UHD/SoapySDR backend connected through a physical RF network, while
still keeping compatibility to run on virtual RF ZeroMQ network, based
on the resources used (controlled by scenarios). For instance, one can
first run a suite through the phyisical RF (using 2 UHD-controlled SDRs)
and afterwards with ZeroMQ using the following default-suites.conf:
- 4g:srsenb-rftype-uhd+srsue-rftype-uhd
- 4g:srsenb-rftype-zmq+srsue-rftype-zmq
Change-Id: I7dbbe328f4c0225fe74e878bb2da13fe39ccf049
2 tests (iperf3, ping) working against a full srs{UE,ENB,EPC} network
using ZeroMQ backend for RF (so no real RF support yet, that will come
next).
Related: OS##4295, OS#4296
Change-Id: I290c0d79258a9f94f00c7ff2e1c6c5579c0e32f4
Force TRXDv0 when using sysmocell-5k as a TRX, since its implementation
(different than osmo-trx) doesn't support higher versions. Furthermore,
it will crash upon receival of SETFORMAT string. By forcing maximum TRXD
version to 0, osmo-bts-trx won't sent any SETFORMAT message since 0 is
the initial version to use.
Depends: osmo-bts.git I5eb1fdc002f9d7f4acf475356d8fc998dc8f6326
Related: OS#4006
Change-Id: Ic95c38d91dba354ae64c5edbfcea3fbbf34a7de3
In the quest to support multiple testcases we will use a single
script. Parts can be enabled/disabled depending on which tests
we want/need to run.
Change-Id: I8a093671173976eba9215c00a7aea0f6cab467c6
Bind the mobile's to a random (chosen by the kernel) VTY port. The
CLI option was removed and I added a new VTY command to be able to
specify the port in addition to the address.
Change-Id: Ie40a2ba156ba5674d37a15eb30e5b2527e75fbe7
It's very close to the osmo-bts-trx but without osmo-trx. Modify
the suite to make use of this BTS.
Change-Id: I9f5a2501eb4473ccf2287c902ee207c6a45a1bc5
It's always been the default anyway, so no need to explicitly state it.
Furthermore, recently (osmobsc 167cb828665b91ed7d28007abd4a1862ebbb78c9)
force-combined-si was enabled by default for nanoBTS due to issues with
some MS not registering when it's not enabled, so let's osmo-bsc decide
were should it be enabled.
Related: OS#3063
Change-Id: I97b10406a4a0048c66a47aa7d32a113f0c0366d1
Otherwise there's too much output. With debug enabled, iperf3 test from
gprs testsuite generates a 111MB osmo-pcu.log.
Change-Id: I687361f3d6ede9a77531cd71204b1b07e0d1af42
Otherwise there's too much output. With debug enabled, iperf3 test from
gprs testsuite generates a 96MB osmo-pcu.log. With log level set to
info, size drops to 1.4M, which is a lot less after compressing in an
archive.
Change-Id: I008234024b9369db42c90ef5d59a013fd2d22718
VTY cmd "logging level all" is deprecated in favour of "logging level
set-all", but the required behaviour in this case is "logging level
set-all".
Change-Id: Ice54fca6be86f05a02ce4ae783e6e42e6958b95d
2nd TRX arfcn is changed in defaults.conf because multi_arfcn requires
them to be alocated in steps of 4 starting from TRX0.
It is not enabled by default yet on B200 (it must use it to support
several TRX) because current host running osmo-gsm-tester is not
performant enough and cannot keep up with timers due to multi-arfcn CPU
overhead.
Change-Id: I096df82ad1f4cbb41dfbd6a78466a845f34be385
* This commit is a preparation for future commits to add support for
different osmo-trx devices and backends like osmo-trx-lms.
* Drop deprecated osmo-trx-* cmd line params and use VTY cfg to set them.
* As number of osmo-trx related osmo-gsm-tester attributes grow, group
them togther in an "osmo_trx" dictionary.
Change-Id: I77d29413c9e3b600b796627ba366f80c3281b7e1
Since osmo-hlr.git I1d09fab810a6bb9ab02904de72dbc9e8a414f9f9, USSD
processing has been moved to osmo-hlr and prefix routing needs to be
configured, otherwise USSD requested are answered back to the MS with an
error "ss-NotAvailable (18)".
mesage received for extension resolution (*#100#) had its format change,
so update to new format (carriage return at the end was dropped).
Change-Id: I5f75eff0df2d20d7f9b39e69184cffb0e635713d
Avoid being stuck in c7 state and use the c7-any-timeout with a low
value. Do not attempt to store SMS in the home directory (if they
are received).
Change-Id: I4bb59130a04852bc43af9ef3602b129f40e9e170
Andre Puschmann
Pau Espin