This should handle OML channel combinations with CBCH and activate the
CBCH SAPI towards the DSP correspondingly. What is still missing is
sending any actual information over the CBCH in respons to the
PH-RTS.ind coming up from L1.
Read the serial number once and format it as a string. In
case no serial number is present -1 will be returned.
Manually tested with a slightly modified version. serial_nr
was the expected one.
Add new power actions for the sysmoBTS2050. This allows to
switch off the secondary/slave when the system temperature
is too high and back on when the normal level is reached.
Do not allow to switch off the master (so remove the enum
value), do not check if the slave is switching itself off.
Instead of keeping state to remember what was done and needs
to be undone this patch introduces actions that will be executed
when the system is back to normal.
By design the system is considered to be in the normal state
and these actions will be only executed after the system is
coming back to the normal state.
One advantage of this scheme is that an operator can decide
that an overheated systems hould be off duty and requires manual
interaction to be allowed back in service.
The change has only been smoke tested
Fixes: SYS#833
Read the clock calibration from the place that will be read by
the BTS process. Use the standard eeprom code for doing that.
The code assumes that this and the other eeprom code don't
write/invlidate the others reason. If that assumption would not
be true calls to eeprom_free_resources should be added.
For systems without direct access to the PA the best option
is to simply switch off the bts service. This will stop the
transmission which will take load from the DSP/FPGA/RF circuit
and indirectly from the PA as well.
We should introduce "pa-on and bts-on" that can be executed
as "normal" action.
Somebody could decide to switch off the PA in the warning level
already. Support this mode of operation. This means we could have
a config that:
* Enables the PA in the normal level
* Disables it in the critical level
With kdbus or better IPC we could even have the PA and other
parts be represented as service that talk to a bts manager and
then simply execute start/stop requests. This would make the
entire TODO entry irrelevant as state would be managed by
systemd and one can see the time the service was executed.
With "show bts 0" all objects were still listed as dependency.
Once the BTS has been started.. move all the other objects into
the enabled state. Our OpenBSC OML code doesn't care but people
using the VTY to inspect state will be more happy.
One day... we will create proper statemachines inside the BTS
and the BSC instead of changing the state in the BTS impl.
Fixes: ONW#1330
The service file will prevent a re-launch of the sysmobts.service
in case the main process exits with '1'. In case the ethernet is
not available yet the routine would fail and the sysmobts process
will not be restarted.
unable to connect/bind socket: Network is unreachable
<000f> input/ipaccess.c:885 cannot open OML BTS link: Network is unreachable
unable to connect to BSC
root@sysmobts-v2:~# echo $?
2
Fixes: SYS#736
bts_ctrl_lookup.c: In function 'bts_controlif_setup':
bts_ctrl_lookup.c:97:2: warning: implicit declaration of function 'bts_ctrl_cmds_install' [-Wimplicit-function-declaration]
rc = bts_ctrl_cmds_install(bts);
^
libosmo-abis doesn't make it easy to have these parameters
as const.. just declare it non-const in the api. We pass
a static string but we know it will not be modified.
We use the completion call-back from L1 to compare the instructed
TRX board output power with the actual value as reported back from
L1.
Right now we only print an error message in case the values disagree.
In the future we might want to either use that value as part of our
calculation or send an OML alarm report to the BSC.
We do not have the vty test script to do roundtrip testing. There
is no max-initinal-pout, then there was a typo inside 'initial' and
for the relative step size the unit is dB/mdB. Fix both of that.
Back in March 2013, some structures and defines related to decoded
measurement reports have been moved from openbsc to libosmocore
(libosmocore e128f4663104ed64e33e362cff2566f36d65e658) so that they can
be used also from osmo-bts. This finally follows up on that.
You need openbsc 7ff4f0e0fc692bfab829da50edb104e58b271e7e or later.
This sysmobts specific control interface allows for clock calibration
from an external program by means of the "trx.0.clock-info" and
"trx.0.clock-correction" values.
Using this control interface, an external program can request
attentuation of the transmitter for thermal management reasons. The
external application doesn't have to know anthing about the actual
transmit power, but it can just configure a certian value of milli-dB
(1/10000 bel) and update (increase/decrease) that value depending on
the thermal environment.
In order to support transmit power reduction by thermal management
as well as the variety of new internal / external PA configurations
of BTSs, we need a slightly more complex system.
Also, as at high power a single dB can be quite a big difference,
we are now doing all computations in milli-dB(m), i.e. 1/10000 bel.
Ramping is now used both for up and down ramping, as that is useful in
cases where you want to gracefully shut down a cell by shrinking its
radius, gradually handing over subscribers to neighboring cells.
Furthermore, this code is becoming part of the 'common' codebase, as it
is not really specific to how sysmobts is working.
The user can specify a single aggregate value for external system
gain/attenuation. Let's say you have 1dB loss of antenna cable, so you
can put that as 'user-gain -1' into the config, which means that a
'transmit power of 20dBm' will be compensatet for that and the TRX is
instructed to output 21dBm to compensate the cable loss. Similarly,
external PAs can be described by a positive user-gain.
One of the next steps will be to communicate those values and the
nominal power capability of the specific BTS to the BSC, so the BSC will
automatically show correct signal levels in the VTY and log files.
The code includes provisions for future extensions regarding
* an external and an internal PA with calibration tables
* a thermal attenuation setting to be controlled by the site manager
Harald Welte
Holger Hans Peter Freyther