The ip.access nanoBTS appears to send quite broken NTP timestamps in
the RTCP messages might confuse equipment that uses the sender report
of the BTS. Make it easy to experiment by adding an option to drop RTCP.
In case the connection should not be created/accepted release
the channel by sending a RR Release and de-activating the
SACCH. Phones should deal better with that behavior.
In case the call handling starts on a TCH/H switch to a TCH/F
if fullrate is requested. Add a method that is used to determine
if the mode and current channel are compatible with each other.
control_if.c:521:2: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘uint64_t’ [-Wformat]
osmo_bsc_bssap.c:473:3: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 7 has type ‘unsigned int’ [-Wformat]
mgcp_main.c:162:4: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘unsigned int’ [-Wformatt]
We want to have multiple MSCs but we also have some data
that is only present on a per BSC basis. Right now the
MSC data is not allocated with talloc, so we have some
change in the talloc contexts.
osmo_bsc_main.c: In function ‘main’:
osmo_bsc_main.c:398:2: warning: implicit declaration of function ‘bts_init’ [-Wimplicit-function-declaration]
osmo_bsc_main.c:399:2: warning: implicit declaration of function ‘libosmo_abis_init’ [-Wimplicit-function-declaration]
osmo_bsc_main.c:418:2: warning: implicit declaration of function ‘bsc_bootstrap_network’ [-Wimplicit-function-declaration]
osmo_bsc_api.c: In function ‘bsc_cm_update’:
osmo_bsc_api.c:195:2: warning: ‘return’ with a value, in function returning void [enabled by default]
osmo_bsc_api.c:193:28: warning: unused variable ‘sccp’ [-Wunused-variable]
Instead of building complex manual byte-wise parsers, we simply use two
strtok_r loops: one iterating over all the lines, the next one
iterating over the invididual space-separated elements in the first line.
The benefit is that we now accept \r, \n or \r\n, or any multiple of
them as line ending. This works around incompliant MGCP implementations
like that of Zynetix MSC.
Addition: mgcp_analyze_header returns 0 when all out parameters have
been set.
Signed-off-by: Holger Hans Peter Freyther <zecke@selfish.org>
In addition to SI 2 and SI 5, the SI 2ter and 2bis is generated, if
neighbour cells in other bands exist. Also it is indicated in the rest
octets of SI3, that SI 2ter is used. If no neighbour cell in a different
band exists, the SI 2ter and SI 5ter is omitted.
A special case is P-GSM range (channels 1-124). To be compatible with
older phones, SI 2bis and SI 5bis is used. If the BCCH lays inside the
P-GSM band, only neighbour cells of the P-GSM range are included in
SI 2 and SI 5. If neighbour cells exist in the same band (900), but lay
outside the P-GSM range, the SI 2bis and SI 5bis is used to extend the
list of neighbour cells. The extension is also indicated in SI 2 and
SI 5. If the BCCH lays inside the P-GSM range, but no neighbour cell
exists in the same band outside the P-GSM range, the SI 2bis ans SI 5bis
are omitted.
strstr() was used with wrong argument order, causing it to always match,
and causing an invalid response to a variety of different SS and USSD
requests.
This has apparently caused havoc among a number of HTC phones which
issue SS requests without user interaction upon boot, and then trip over
our inappropriate response.
This must have been obsoleted by the move to libosmo-abis.
GCC warning:
bts_ipaccess_nanobts.c: In function ‘ipaccess_drop_oml’:
bts_ipaccess_nanobts.c:509:21: warning: variable ‘line’ set but not used [-Wunused-but-set-variable]
The old BSC code had code to override the payload type, this has
been removed, remove the variable accessing it.
GCC warning:
abis_rsl.c: In function ‘ipa_rtp_pt_for_lchan’:
abis_rsl.c:1590:22: warning: unused variable ‘net’ [-Wunused-variable]
Introduce a SS_CCCH for the paging and the rach load. The paging
code could now start using the signal.
GCC warning:
abis_rsl.c: In function ‘rsl_rx_ccch_load’:
abis_rsl.c:1371:11: warning: variable ‘rach_access_count’ set but not used [-Wunused-but-set-variable]
abis_rsl.c:1370:11: warning: variable ‘rach_busy_count’ set but not used [-Wunused-but-set-variable]
abis_rsl.c:1369:11: warning: variable ‘rach_slot_count’ set but not used [-Wunused-but-set-variable]
attribute get|set <0-255> (.HEX) was never implemented and the
output about the unused attributes clutter the build output, remove
them.
GCC warning:
abis_nm_vty.c: In function ‘oml_attrib_get’:
abis_nm_vty.c:141:25: warning: unused variable ‘oms’ [-Wunused-variable]
abis_nm_vty.c: In function ‘oml_attrib_set’:
abis_nm_vty.c:152:25: warning: unused variable ‘oms’ [-Wunused-variable]
Use LOGP(DNM, LOGL_ERROR, ...); for errors in the
abis_nm_rx_sw_act_req method.
GCC warning:
abis_nm.c: In function ‘abis_nm_rx_sw_act_req’:
abis_nm.c:412:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Assume nothing special needs to be done for the Nokia
*site hardware.
GCC warning:
gsm_data.c: In function ‘gsm_set_bts_type’:
gsm_data.c:342:2: warning: enumeration value ‘GSM_BTS_TYPE_NOKIA_SITE’ not handled in switch [-Wswitch]
I'm sure I read somewhere that it actually was 0..1024, as I kept
wondering how stupid it was to use 10bit+1. However, that source
was incorrect, as GSM TS 05.05 quite clearly states 0..1023
When we get an assignment command from the MSC, we no longer have to
check statically for certain codecs, as we have a vty-configured list of
codecs that is checked just below.
Holger Hans Peter Freyther
Sylvain Munaut
Harald Welte