Verify that CSD ipaccess CRCX/MDCX has the CSD RTP payload type, and
that the RSL_IE_IPAC_RTP_CSD_FMT IE is set with
RSL_IPA_RTP_CSD_TRAU_BTS.
Related: OS#4393
Change-Id: Id0e0c5631d7a36635e1ef49cf5bf554f0336556b
Prepare to test CSD in BSC_Tests.ttcn. After sending a BSSAP assignment
request to the BSC with channel type data, the BSC will send a channel
activation via RSL to the BTS (which is emulated by the testsuite).
Without CSD support in the RSL template, the testsuite is unable to
decode the message, prints "Data remained at the end of the stream
after successful decoding" and the test fails.
Related: OS#4393
Change-Id: Ief2d95c7e9d71afb26fa74da755294226c8e158d
In TTCN-3 it's not possible to store templates in records, so in
f_assignment_codec() we match received RSL_IE_MR_CONFIG against the
value (not template!) stored in g_pars.expect_mr_conf_ie.
Because of that, the length field is not being calculated by TITAN
for us, so we need to calculate it in ts_RSL_MultirateCfg ourselves.
Automatic length calculation only works during encoding/decoding
and when matching against a receive template.
Change-Id: I595be86d69913ba25e965a5a5c6977e00c342e60
The RSL MultiRate configuration IE is all about AMR (Adaptive Multi
Rate) codec, so there is no need for 'amr_' prefix in field names.
Change-Id: If63ee50e8681ad4e0a202f142f2fca2268d55079
New TC_assignment_osmux_bts is added which tests Osmux used only
BTS<->BSC.
Existing TC_assignment_osmux is renamed to TC_assignment_osmux_cn,
and a new TC_assignment_osmux is added which tests using Osmux on both
sides (towards BTS and CN).
Related: SYS#5987
Change-Id: I6e82eb9d995de988b812001e1c4cf6923509de66
This test case verifies the new channel allocation mode, which
is expected to switch between ascending and descending modes
dynamically based on the following two configurable parameters:
* Uplink RxLev threshold (and min number of samples),
* C0 (BCCH carrier) channel load threshold.
The test case scenario includes:
Case a) Unknown Uplink RxLev => fall-back to ascending.
Case b) Not enough RxLev samples => use ascending.
Case c) Uplink RxLev below the threshold => use ascending.
Case d) Uplink RxLev above the threshold => use descending.
Case e) Uplink RxLev above the threshold, but C0 load is not.
Change-Id: Ia522f37c1c001b3a36f5145b8875fbb88311c2e5
Related: SYS#5460
* t_RSL_IE_ActType_PDCH is actually a constant, not a template.
* tr_RSL_CHAN_ACT_PDCH makes no use of parameter 'mode'.
* Accomplish tr_RSL_CHAN_ACT_PDCH with a send template.
* Use 'present' qualifier for receive template parameters.
Change-Id: Ie62a92daaacf4de5f05dd1f3f5b4a2a5e4ee6dd6
So far all handover tests trigger handover via VTY command. This means
that any bugs introduced in measurement report handling and handover
target selection are by definition not caught.
Almost a year ago, fixing a handover oscillation bug for intra-BSC
handover introduced a segfault for inter-BSC handover targets, because
for those the target.bts is NULL. Show this bug.
Related: OS#5324 SYS#5259
Related: I5a3345ab0005a73597f5c27207480912a2f5aae6 (osmo-bsc)
Change-Id: Iba033c32015173f57dbb1c211aefab1a9094e29d
This way functions like f_inet_addr() and f_inet6_addr() can be
used directly without converting between bytes and integers.
Change-Id: I389a8cb95c025c9dddc751789223621c15d9b48f
BSC_Tests_VAMOS.ttcn is separate from BSC_Tests.ttcn in order to
instruct osmo-bts-omldummy to pass BTS_FEAT_VAMOS == true in the OML BTS
attributes.
Add tests:
TC_chan_act_to_vamos()
TC_mode_modify_to_vamos_fr()
TC_mode_modify_to_vamos_hr()
TC_assign_to_secondary_lchan_fr()
TC_assign_to_secondary_lchan_hr()
TC_vamos_multiplex_tch_f_tch_f()
TC_vamos_multiplex_tch_h_tch_h_tch_h_tch_h()
Change-Id: I2c504099163a30ea102cbd26d3615ca2e5ce1e64
This way it's consistent with ts_RSL_ChanMode, and there is
no need to pass dtx_downlink := false as the first param.
Change-Id: I0b87ef87f8cfff1c96b0beead29d549d5fe0b7c6
The testcase TC_meas_res_sign_tchX activates a traffic channel in
signalling mode and checks the RSL resulting measurement reports.
The CHANnel ACTIVation message sets "SDCCH" as "Channel rate and Type"
value. This is invalid, the "Channel Rate and Type" sould be set to "Half /
Full rate TCH Channel Lm / Bm" (while the speech or data indicator is
still set to "Signalling")
Change-Id: I51887b0d0379fcc1f4483d08dfdd6869e7a9f963
Related: OS#4799
Unlike the RSL_IE_MS_Power, where power_level is 5 bit long, in
the RSL_IE_BS_Power it's 4 bit long. Fix this.
Change-Id: Ic0cb2275ef585754b9ae5e3d8077ca652afd9365
On channel establishment the first measurement result may lack the
measurement reports from the MS. This is normal behavior, so lets
tolerate that.
Change-Id: Ib2f511991349ab15e02db9c5e45f0df3645835a4
Related: OS#2975
In this testsuite, we simulate BTS and CBC by attaching to RSL and CBSP
protocol interfaces of the BSC. We then issue a variety of CBSP
commands to the BSC and check for corresponding action on both the BTS-
facing RSL as well as responses on the CBSP side.
Change-Id: Ia6ffac181f50586d06d2f29bca1c57285179e861
osmo-bts does currently not use the signaled lchan BS power level, nor
does it update the BS power IE returned in the measurement results.
Change-Id: If91fb57b4070c60bb277d0b55d69ee3dde47ee48
The idea of this test case (as can bee seen from its name) is to
verify handover RACH detection. What we basically do is:
1. Activate a logical channel on the BTS side (HO_SYNC for now);
2. Switch the MS (e.g. trxcon) to that channel without waiting
for Immediate Assignment and sending Access Burst;
3. Send an Access Burst on that channel using RA = HO_REF;
4. Wait for RSL HANDOver DETected from the BTS;
5. Release a dedicated connection.
There is no way to verify if the Handover Reference received
from the MS matches the one that was sent to the BTS. We can
introduce a separate test case that would just send an Access
Burst with RA != HO_REF.
Change-Id: If2e8d9c9947823df62f4bcc9a7fcd20734ff7858
Depends on: (trxcon) Ia967820a536c99966ba2c60b63d2ea9edb093f46
This test will currently fail due to a MODE MODIFY NACK, even though the
channel mode is not modified.
Related: OS##3750
Change-Id: I4cbea499bb6a331d314e6573548a4540945208b5
Some of our files didn't have a copyright notice at all, let's add
it. Also, update the notices in other files and ensure a SPDX
identifier is present in all but the most trivial files.
Change-Id: If7fa19ce484b415bc645e39b3d0d666b44b5f0fd
The existing code structure could only test for normal messages with a
NULL default, but didn't handle situations where normal and/or schedule
messages were superimposed on top of DEFAULT messages.
Also, prepare the infrastructure for testing both CBCH BASIC and CBCH
EXTENDED.
No new tests are introduced, the code should behave identical before
and after this patch.
Change-Id: I144c7d833b79c648b1ac69a6155f3603025ede5c
Related: OS#4011
Andreas Eversberg
Vadim Yanitskiy
Harald Welte
Oliver Smith
Pau Espin
Neels Hofmeyr
Philipp Maier
Eric Wild