You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
chan-capi/capi.conf

100 lines
6.4 KiB

;
; CAPI config
;
;
; general section
[general]
nationalprefix=0 ; or for example "+49"
internationalprefix=00 ; or for example "+"
;subscriberprefix=+4969 ; prefix including area code (some lines need this)
rxgain=1.0 ;linear receive gain (1.0 = no change)
txgain=1.0 ;linear transmit gain (1.0 = no change)
language=de ;set default language
;ulaw=yes ;set this, if you live in u-law world instead of a-law
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
; interface sections ...
[ISDN1] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;Use one interface section for each ISDN port!
;ntmode=yes ;if the ISDN card operates in NT-mode, set this to 'yes'
isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller ID to that interface for dial-out,
;this caller ID will be used when the dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;CAPI controller number of this interface/port
group=1 ;dialout group
;prefix=0 ;set a prefix to the calling number on incoming calls
softdtmf=on ;enable/disable software DTMF detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed DTMF detection
faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call.
;(default '0' meaning for the whole duration of the call)
faxdestination=custom-fax,fax,1 ;Set custom context, exten and priority to jump to on faxdetect.
;Default is "<current-context>,fax,1".
accountcode= ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=isdn-in ;context for incoming calls
;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and the PBX may
;play MOH.
;immediate=yes ;DID: immediate start of PBX with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start PBX on CONNECT_IND and do not wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable it before you start recording voicemail
;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
;echocancel=yes ;Dialogic(R) Diva(R) (CAPI) echo cancellation (yes=g165)
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
;echocancelpath=1;Dialogic(R) Diva(R) (CAPI) echo cancellation path
;(possible values: default '1' - E.1/T.1/S0, '2' - IP, '3' - both)
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
;incorporate variable gain in the signal path.
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;PBX call group
;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
;language=de ;set language for this device (overwrites default language)
;disallow=all ;RTP codec selection (valid with Dialogic(R) Diva(R) Media Boards only)
;allow=all ;RTP codec selection (valid with Dialogic(R) Diva(R) Media Boards only)
devices=2 ;number of concurrent calls (B-Channels) on this controller
;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number
;divaqsig=on ;enable Diva QSIG and protocol independent implementation
;mwifacptynrtype=0;type of MWI facility party number, 0 - unknown (default), 1 - public
;mwifacptynrton=0 ;MWI facility party number type of number and numbering plan identification
; (coding as for byte 0 of the calling party number).
; This byte is only valid if byte mwifacptynrtype contains the value 1
;mwifacptynrpres=0;MWI facility party number type presentation and screening indicator
; (coding as for byte 1 of the calling party number).
; This byte is only valid if byte mwifacptynrtype contains the value 1
;mwibasicservice=1;MWI basic Service, coded in accordance with ETS 300 196 [D.5]
;mwiinvocation=2 ;MWI invocation mode, 0 - deferred, 1 - immediate, 2 - combined,
; 65535 - suppres invocation code
;mwimailbox=12345 ;',' separated list of mailboxes for MWI in format:
; mailbox[:controlling user number[:controlling user provided number]][@context]
;hlimit=10 ;Do not use this controller for outgoing calls if less than 'hlimit' free channels is
;left on this controller.
;slimit=10 ;Try to use for outgoing calls other controller in group if less than 'slimit' free
;channels is left on this controller. Always try to 'fill up' the controller with
;smalest number in group. Create call if less than 'slimit' free channels left and
;no other controller with respect to free channel count was found in group.