; ; CAPI config ; ; ; general section [general] nationalprefix=0 ; or for example "+49" internationalprefix=00 ; or for example "+" ;subscriberprefix=+4969 ; prefix including area code (some lines need this) rxgain=1.0 ;linear receive gain (1.0 = no change) txgain=1.0 ;linear transmit gain (1.0 = no change) language=de ;set default language ;ulaw=yes ;set this, if you live in u-law world instead of a-law ;jb..... ;with Asterisk 1.4 you can configure jitterbuffer, ;see Asterisk documentation for all jb* setting available. ;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold. ; interface sections ... [ISDN1] ;this example interface gets name 'ISDN1' and may be any ;name not starting with 'g' or 'contr'. ;Use one interface section for each ISDN port! ;ntmode=yes ;if the ISDN card operates in NT-mode, set this to 'yes' isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial) ;when using NT-mode, 'DID' should be set in any case incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any ;defaultcid=123 ;set a default caller ID to that interface for dial-out, ;this caller ID will be used when the dial option 'd' is set. ;controller=0 ;ISDN4BSD default ;controller=7 ;ISDN4BSD USB default controller=1 ;CAPI controller number of this interface/port group=1 ;dialout group ;prefix=0 ;set a prefix to the calling number on incoming calls softdtmf=on ;enable/disable software DTMF detection, recommended for AVM cards relaxdtmf=on ;in addition to softdtmf, you can use relaxed DTMF detection faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or ;outgoing calls. (default='off', possible values: 'incoming','outgoing','both') faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call. ;(default '0' meaning for the whole duration of the call) faxdestination=custom-fax,fax,1 ;Set custom context, exten and priority to jump to on faxdetect. ;Default is ",fax,1". accountcode= ;PBX accountcode to use in CDRs ;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation') context=isdn-in ;context for incoming calls ;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If ;set to 'local' (default value), no hold is done and the PBX may ;play MOH. ;immediate=yes ;DID: immediate start of PBX with extension 's' if no digits were ; received on incoming call (no destination number yet) ;MSN: start PBX on CONNECT_IND and do not wait for SETUP/SENDING-COMPLETE. ; info like REDIRECTINGNUMBER may be lost, but this is necessary for ; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE. ;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable it before you start recording voicemail ;or your files may get choppy. (you can use capicommand(echosquelch|no) for this) ;echocancel=yes ;Dialogic(R) Diva(R) (CAPI) echo cancellation (yes=g165) ;(possible values: 'no', 'yes', 'force', 'g164', 'g165') ;echocancelpath=1;Dialogic(R) Diva(R) (CAPI) echo cancellation path ;(possible values: default '1' - E.1/T.1/S0, '2' - IP, '3' - both) echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers) ;echotail=64 ;echo cancel tail setting (default=0 for maximum) ;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might ;incorporate variable gain in the signal path. ;bridge=yes ;native bridging (CAPI line interconnect) if available ;callgroup=1 ;PBX call group ;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup) ;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to. ;language=de ;set language for this device (overwrites default language) ;disallow=all ;RTP codec selection (valid with Dialogic(R) Diva(R) Media Boards only) ;allow=all ;RTP codec selection (valid with Dialogic(R) Diva(R) Media Boards only) devices=2 ;number of concurrent calls (B-Channels) on this controller ;(2 makes sense for single BRI, 30/23 for PRI/T1) ;jb..... ;with Asterisk 1.4 you can configure jitterbuffer, ;see Asterisk documentation for all jb* setting available. ;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold. ;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant ;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number ;divaqsig=on ;enable Diva QSIG and protocol independent implementation ;mwifacptynrtype=0;type of MWI facility party number, 0 - unknown (default), 1 - public ;mwifacptynrton=0 ;MWI facility party number type of number and numbering plan identification ; (coding as for byte 0 of the calling party number). ; This byte is only valid if byte mwifacptynrtype contains the value 1 ;mwifacptynrpres=0;MWI facility party number type presentation and screening indicator ; (coding as for byte 1 of the calling party number). ; This byte is only valid if byte mwifacptynrtype contains the value 1 ;mwibasicservice=1;MWI basic Service, coded in accordance with ETS 300 196 [D.5] ;mwiinvocation=2 ;MWI invocation mode, 0 - deferred, 1 - immediate, 2 - combined, ; 65535 - suppres invocation code ;mwimailbox=12345 ;',' separated list of mailboxes for MWI in format: ; mailbox[:controlling user number[:controlling user provided number]][@context] ;hlimit=10 ;Do not use this controller for outgoing calls if less than 'hlimit' free channels is ;left on this controller. ;slimit=10 ;Try to use for outgoing calls other controller in group if less than 'slimit' free ;channels is left on this controller. Always try to 'fill up' the controller with ;smalest number in group. Create call if less than 'slimit' free channels left and ;no other controller with respect to free channel count was found in group.