renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs@denx.de>
The Nand flash was unable to read and write properly
due to Nand Chip Select (nCE) setup was in reverse
order. Also, increase the Nand time out value to 60.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.
This patch also removes some dead code.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D)
specifies that BankSel#1 is not connected, while bootloader memory
configuration is (board/amcc/sequoia/sdram.c):
mtsdram(DDR0_10, 0x00000300);
i.e. both Chip Selects used - not correct.
If we change to correct value here:
mtsdram(DDR0_10, 0x00000100);
memory is accessible OK also.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Stefan Roese <sr@denx.de>
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.
Signed-off-by: Andy Fleming <afleming@freescale.com>
old code implemented the QE_ENET10 errata only for Silicon
Revision 2.0. New code reads now the Silicon Revision
register and sets dependend on the Silicon Revision the
values as advised in the QE_ENET10 errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.
Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Clock pin must have input enabled for MMC3 to work.
Also enable pull-ups for cmd/data lines to be consistent
with remaining MMC host pin setup.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds OMAP3 cpu type auto detection based on OMAP3 register
and removes hardcoded values.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.
To handle board differences you can call function beagle_get_revision().
E.g.:
if (beagle_get_revision()) {
/* do special revision C stuff here */
}
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
* Make Overo GPIO114 an input for touchscreen PENDOWN
* Make Overo GPIO144-147 readable
* Make Overo EHCI pinmux match beagle rev c setup
* Adjust pinmux for SMSC911X network chip support
* Remove unnecessary GPIO setup
* Fix merge error in Makefile
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
THe TQM8xxL use a ahnd-optimized linker script to efficiently use the
small boot sectors in the flash. This patch makes some room in the
first sector to prepare for a size increase of lib_generic/vsprintf.o
by a future patch.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch prepares the good old PMC405 board support for
upcoming PMC405V2 patches.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes coding style for PMC405 board support.
Also some unneeded features/code is removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The ecm variable in sdram.c was being declared for all 8548, but only
used by specific 8548 boards, so we make that variable require those
specific boards, too
The nand code was using an index "i" into a table, and then re-using "i"
to set addresses for each upm. However, then it relied on the old value
of i still being there to enable things. Changed the second "i" to "j"
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds the workaround for erratum DDR20 according to MPC8548
Device Errata document, Rev. 1: "CKE signal may not function correctly
after assertion of HRESET". Furthermore, the bug DDR19 is fixed in
processor version 2.1 and the work-around must be removed.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch makes accesses to the system memory cachable by removing the
caching-inhibited and guarded flags from the relevant TLB entries for
the TQM8548_BE and TQM8548_AG modules. FYI, the Freescale MPC85* boards
are configured similarly.
This results in a big averall performace improvement. TFTP downloads,
NAND Flash accesses, kernel boots, etc. are much faster.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
This patch add support for the 1 GiB DDR2-SDRAM on the TQM8548_AG
module.
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
As the reset vector is located at 0xfffffffc, all flash sectors from the
beginning of the U-Boot binary to 0xffffffff must be protected. On the
TQM8548-AG having small sectors at the end of the flash it happened that
the last two sector were not protected and an "erase all" left an
un-bootable system behind:
Bank # 2: CFI conformant FLASH (32 x 16) Size: 32 MB in 270 Sectors
AMD Standard command set, Manufacturer ID: 0xEC, Device ID: 0x257E
Erase timeout: 8192 ms, write timeout: 1 ms
FFFA0000 E RO FFFC0000 RO FFFE0000 RO FFFE4000 RO FFFE8000 RO
FFFEC000 RO FFFF0000 RO FFFF4000 RO FFFF8000 E FFFFC000
The same bug seems to be in drivers/mtd/cfi_flash.c:flash_init() and many
board BSPs as well.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Heiko Schocher