This patch allows U-Boot to use buffered writes to the Spansion NOR
flash installed on this board, and eliminates long delays in network
transfers after the board startup.
Also modify flash layout to embed main and redundant environment
blocks in the U-Boot image.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for booting from 2k page sized NAND device
(e.g. Micron 29F2G08AAC).
Tested on AMCC Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Currently U-Boot crashes in ppc_4xx_eth_init on sequoia
with cache enabled (TLB Parity exeption). This patch
fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently U-Boot crashes on sequoia board in CPU POST if
cache is enabled (CONFIG_4xx_DCACHE defined). The cache
won't be disabled by change_tlb before CPU POST because
there is an insufficient adress range check since
CFG_MEM_TOP_HIDE was introduced. This patch tries to fix
this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Current assembler codes are inconsistent in the way of register jump
instruction usage; some use jr, some use j. Of course GNU as allows both
usages, but as can be expected from `Jump Register' the mnemonic `jr' is
more intuitive than `j'. For example, Linux doesn't have `j <reg>' usage
at all.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
MC13783 is a multifunction IS with an SPI interface to the host. This
driver handles the RTC controller in this chip.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is an SPI driver for i.MX and MXC based SoCs from Freescale. So far
only implemented and tested on i.MX31, can with a modified register layout
and definitions be used for i.MX27, I think, MXC CPUs have similar SPI
controllers too.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Split the arch-specific logic out of the common go code and into a dedicated
weak function called do_go_exec() that lives in cpu directories. This will
need review from i386/nios people to make sure I didn't break them.
Change the bootelf setup function into a dedicated weak function called
do_bootelf_exec. This way ports can control the behavior however they
like before/after calling the ELF entry point.
Rearrange ARM boards in Makefile so that ARM926EJ-S boards
are no longer under ARM92xT header.
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Ack-By Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch removes the board dependent parts from
"drivers/mtd/dataflash.c".
Each board relying on this, will have the appropriate
code in a new file, "partition.c" in the board directory.
board Makefiles updated to use the file.
The dataflash partitions are aligned on sector/page boundaries.
The CONFIG_NEW_DF_PARTITION was used to create named partitions
This is now the default operation, and the CONFIG variable is removed.
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Before new uImage code was merged, bootm code allowed for the kernel image to
get overwritten during decompresion. new uImage introduced a check for image
overwrites and refused to boot the image that got overwritten. This patch
restores the old behavior. It also adds a warning when the image overwriten is
a multi-image file, because in such case accessing componentes other than the
first one will fail.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There are two NAND entries with ID 0xDC and this obviously causes problems.
In the kernel, they punted the first entry, so we should do the same.
See this upstream e-mail for more info:
http://lists.infradead.org/pipermail/linux-mtd/2007-July/018795.html
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cache operations have to take line address (addr), not start_addr.
I noticed this bug when debugging ping failure.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Before the first call of ide_reset(), the level of the IDE reset
signal on the TQM5200 is low (reset asserted). This patch sets the
default value to high (reset not asserted).
Currently this patch fixes no real problem, but it is cleaner to
assert the reset signal only on demand, and not permanently.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
According to the ata (ata5) specification the RESET- signal
shall be asserted for at least 25 us. Without this patch,
the RESET- signal is asserted on some boards for only < 1 us
(e. g. on the TQM5200). This patch adds a general delay of
25 us to the RESET- signal.
Without this patch a Platinum 4 GiB CF card is not recognised
properly on boards with a TQM5200 (STK52xx, TB5200).
Signed-off-by: Martin Krause <martin.krause@tqs.de>
In function 'logbuff_init_ptrs':
cmd_log.c:79: warning: pointer targets in assignment differ in signedness
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
If the hardware watchdog detects a voltage error, the watchdog sets
GPIO62 to low. The watchdog POST has to detect this low level.
Signed-off-by: Sascha Laue <leglas0@legpc180.leg.liebherr.i>
Current libata.h of u-boot is out of sync from linux kernel,
this patch make it be consistent with linux kernel.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Tor Krill <tor@excito.com>
The linux kernel is now mostly ARCH=powerpc, so to make life easier
allow use to use ARCH=powerpc and convert it to ARCH=ppc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It should access with 16-bit instead of 8-bit
Now it uses the generic memcpy with 8-bit access. It means it reads wrong data from OneNAND.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.
Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Replace CONFIG_8xx and CONFIG_MCF532x to CONFIG_MII_INIT in
cmd_init.c. Add CONFIG_MII_INIT to board configuration files
that use mii_init() in cmd_init.c.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Remove test for CONFIG_MPC5200 in drivers/pci/pci_auto.c and define
CONFIG_PCIAUTO_SKIP_HOST_BRIDGE in related board configuration files.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Mike Frysinger