ppc4xx: Big cleanup of PPC4xx defines

This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:

- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
  user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines

Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.

Signed-off-by: Stefan Roese <sr@denx.de>

board/amcc/acadia/acadia.c

@@ -57,7 +57,7 @@ int board_early_init_f(void)
 
 #if !defined(CONFIG_NAND_U_BOOT)
 	/* don't reinit PLL when booting via I2C bootstrap option */
-	mfsdr(SDR_PINSTP, reg);
+	mfsdr(SDR0_PINSTP, reg);
 	if (reg != 0xf0000000)
 		board_pll_init_f();
 #endif
@@ -65,18 +65,18 @@ int board_early_init_f(void)
 	acadia_gpio_init();
 
 	/* Configure 405EZ for NAND usage */
-	mtsdr(sdrnand0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
+	mtsdr(SDR0_NAND0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
-	mfsdr(sdrultra0, reg);
+	mfsdr(SDR0_ULTRA0, reg);
 	reg &= ~SDR_ULTRA0_CSN_MASK;
 	reg |= (SDR_ULTRA0_CSNSEL0 >> CONFIG_SYS_NAND_CS) |
 		SDR_ULTRA0_NDGPIOBP |
 		SDR_ULTRA0_EBCRDYEN |
 		SDR_ULTRA0_NFSRSTEN;
-	mtsdr(sdrultra0, reg);
+	mtsdr(SDR0_ULTRA0, reg);
 
 	/* USB Host core needs this bit set */
-	mfsdr(sdrultra1, reg);
+	mfsdr(SDR0_ULTRA1, reg);
-	mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE);
+	mtsdr(SDR0_ULTRA1, reg | SDR_ULTRA1_LEDNENABLE);
 
 	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */
 	mtdcr(uicer, 0x00000000);	/* disable all ints */

board/amcc/acadia/memory.c

@@ -65,7 +65,7 @@ phys_size_t initdram(int board_type)
 	u32 reg;
 
 	/* don't reinit PLL when booting via I2C bootstrap option */
-	mfsdr(SDR_PINSTP, reg);
+	mfsdr(SDR0_PINSTP, reg);
 	if (reg != 0xf0000000)
 		board_pll_init_f();
 #endif
@@ -81,25 +81,25 @@ phys_size_t initdram(int board_type)
 	gpio_config(CONFIG_SYS_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
 
 	/* 2. EBC in Async mode */
-	mtebc(pb1ap, 0x078F1EC0);
+	mtebc(PB1AP, 0x078F1EC0);
-	mtebc(pb2ap, 0x078F1EC0);
+	mtebc(PB2AP, 0x078F1EC0);
-	mtebc(pb1cr, 0x000BC000);
+	mtebc(PB1CR, 0x000BC000);
-	mtebc(pb2cr, 0x020BC000);
+	mtebc(PB2CR, 0x020BC000);
 
 	/* 3. Set CRAM in Sync mode */
 	cram_bcr_write(0x7012);		/* CRAM burst setting */
 
 	/* 4. EBC in Sync mode */
-	mtebc(pb1ap, 0x9C0201C0);
+	mtebc(PB1AP, 0x9C0201C0);
-	mtebc(pb2ap, 0x9C0201C0);
+	mtebc(PB2AP, 0x9C0201C0);
 
 	/* Set GPIO pins back to alternate function */
 	gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
 	gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
 
 	/* Config EBC to use RDY */
-	mfsdr(sdrultra0, val);
+	mfsdr(SDR0_ULTRA0, val);
-	mtsdr(sdrultra0, val | SDR_ULTRA0_EBCRDYEN);
+	mtsdr(SDR0_ULTRA0, val | SDR_ULTRA0_EBCRDYEN);
 
 	/* Wait a short while, since for NAND booting this is too fast */
 	for (i=0; i<200000; i++)

board/amcc/acadia/pll.c

@@ -51,11 +51,11 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc, 0x0000033c);
+	mtcpr(CPR0_PLLC, 0x0000033c);
-	mtcpr(cprplld, 0x0c010200);
+	mtcpr(CPR0_PLLD, 0x0c010200);
-	mtcpr(cprprimad, 0x04060c0c);
+	mtcpr(CPC0_PRIMAD, 0x04060c0c);
-	mtcpr(cprperd0, 0x000c0000);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(CPC0_PERD0, 0x000c0000);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprclkupd, 0x40000000);
+	mtcpr(CPR0_CLKUP, 0x40000000);
 }
 
 #elif defined(PLLMR0_266_160_80)
@@ -83,13 +83,13 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc, 0x20000238);
+	mtcpr(CPR0_PLLC, 0x20000238);
-	mtcpr(cprplld, 0x03010400);
+	mtcpr(CPR0_PLLD, 0x03010400);
-	mtcpr(cprprimad, 0x03050a0a);
+	mtcpr(CPC0_PRIMAD, 0x03050a0a);
-	mtcpr(cprperc0, 0x00000000);
+	mtcpr(CPC0_PERC0, 0x00000000);
-	mtcpr(cprperd0, 0x070a0707);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(CPC0_PERD0, 0x070a0707);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1, 0x07323200);
+	mtcpr(CPC0_PERD1, 0x07323200);
-	mtcpr(cprclkupd, 0x40000000);
+	mtcpr(CPR0_CLKUP, 0x40000000);
 }
 
 #elif defined(PLLMR0_333_166_83)
@@ -117,12 +117,12 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc, 0x0000033C);
+	mtcpr(CPR0_PLLC, 0x0000033C);
-	mtcpr(cprplld, 0x0a010000);
+	mtcpr(CPR0_PLLD, 0x0a010000);
-	mtcpr(cprprimad, 0x02040808);
+	mtcpr(CPC0_PRIMAD, 0x02040808);
-	mtcpr(cprperd0, 0x02080505);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(CPC0_PERD0, 0x02080505);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1, 0xA6A60300);
+	mtcpr(CPC0_PERD1, 0xA6A60300);
-	mtcpr(cprclkupd, 0x40000000);
+	mtcpr(CPR0_CLKUP, 0x40000000);
 }
 
 #elif defined(PLLMR0_100_100_12)
@@ -143,12 +143,12 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc, 0x000003BC);
+	mtcpr(CPR0_PLLC, 0x000003BC);
-	mtcpr(cprplld, 0x06060600);
+	mtcpr(CPR0_PLLD, 0x06060600);
-	mtcpr(cprprimad, 0x02020004);
+	mtcpr(CPC0_PRIMAD, 0x02020004);
-	mtcpr(cprperd0, 0x04002828);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(CPC0_PERD0, 0x04002828);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1, 0xC8C81600);
+	mtcpr(CPC0_PERD1, 0xC8C81600);
-	mtcpr(cprclkupd, 0x40000000);
+	mtcpr(CPR0_CLKUP, 0x40000000);
 }
 #endif				/* CPU_<speed>_405EZ */
 
@@ -167,12 +167,12 @@ unsigned long get_tbclk(void)
 	/*
 	 * Read PLL Mode registers
 	 */
-	mfcpr(cprplld, cpr_plld);
+	mfcpr(CPR0_PLLD, cpr_plld);
 
 	/*
 	 * Read CPR_PRIMAD register
 	 */
-	mfcpr(cprprimad, cpr_primad);
+	mfcpr(CPC0_PRIMAD, cpr_primad);
 
 	/*
 	 * Determine CPU clock frequency

board/amcc/bamboo/bamboo.c

@@ -487,35 +487,35 @@ int pci_pre_init(struct pci_controller *hose)
 	  | Set priority for all PLB3 devices to 0.
 	  | Set PLB3 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*-------------------------------------------------------------------------+
 	  | Set priority for all PLB4 devices to 0.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*-------------------------------------------------------------------------+
 	  | Set Nebula PLB4 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	return 1;
 }
@@ -695,8 +695,8 @@ void ext_bus_cntlr_init(void)
 	  |
 	  +-------------------------------------------------------------------------*/
 	/* NVRAM - FPGA */
-	mtebc(pb5ap, EBC0_BNAP_NVRAM_FPGA);
+	mtebc(PB5AP, EBC0_BNAP_NVRAM_FPGA);
-	mtebc(pb5cr, EBC0_BNCR_NVRAM_FPGA_CS5);
+	mtebc(PB5CR, EBC0_BNCR_NVRAM_FPGA_CS5);
 
 	/*-------------------------------------------------------------------------+
 	  |
@@ -749,7 +749,7 @@ void ext_bus_cntlr_init(void)
 		case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
 			/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
 			/* Read Serial Device Strap Register1 in PPC440EP */
-			mfsdr(sdr_sdstp1, sdr0_sdstp1);
+			mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
 			boot_selection	= sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
 			ebc_boot_size	= sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
 
@@ -822,7 +822,7 @@ void ext_bus_cntlr_init(void)
 			/* Default Strap Settings 5-7 */
 			/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
 			/* Read Serial Device Strap Register1 in PPC440EP */
-			mfsdr(sdr_sdstp1, sdr0_sdstp1);
+			mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
 			boot_selection	= sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
 			ebc_boot_size	= sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
 
@@ -1013,8 +1013,8 @@ void ext_bus_cntlr_init(void)
 	/*-------------------------------------------------------------------------+
 	  | Initialize EBC CONFIG
 	  +-------------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, EBC0_CFG_EBTC_DRIVEN	   |
+	mtdcr(EBC0_CFGDATA, EBC0_CFG_EBTC_DRIVEN	   |
 	      EBC0_CFG_PTD_ENABLED	  |
 	      EBC0_CFG_RTC_2048PERCLK	  |
 	      EBC0_CFG_EMPL_LOW		  |
@@ -1029,20 +1029,20 @@ void ext_bus_cntlr_init(void)
 	  | Initialize EBC Bank 0-4
 	  +-------------------------------------------------------------------------*/
 	/* EBC Bank0 */
-	mtebc(pb0ap, ebc0_cs0_bnap_value);
+	mtebc(PB0AP, ebc0_cs0_bnap_value);
-	mtebc(pb0cr, ebc0_cs0_bncr_value);
+	mtebc(PB0CR, ebc0_cs0_bncr_value);
 	/* EBC Bank1 */
-	mtebc(pb1ap, ebc0_cs1_bnap_value);
+	mtebc(PB1AP, ebc0_cs1_bnap_value);
-	mtebc(pb1cr, ebc0_cs1_bncr_value);
+	mtebc(PB1CR, ebc0_cs1_bncr_value);
 	/* EBC Bank2 */
-	mtebc(pb2ap, ebc0_cs2_bnap_value);
+	mtebc(PB2AP, ebc0_cs2_bnap_value);
-	mtebc(pb2cr, ebc0_cs2_bncr_value);
+	mtebc(PB2CR, ebc0_cs2_bncr_value);
 	/* EBC Bank3 */
-	mtebc(pb3ap, ebc0_cs3_bnap_value);
+	mtebc(PB3AP, ebc0_cs3_bnap_value);
-	mtebc(pb3cr, ebc0_cs3_bncr_value);
+	mtebc(PB3CR, ebc0_cs3_bncr_value);
 	/* EBC Bank4 */
-	mtebc(pb4ap, ebc0_cs4_bnap_value);
+	mtebc(PB4AP, ebc0_cs4_bnap_value);
-	mtebc(pb4cr, ebc0_cs4_bncr_value);
+	mtebc(PB4CR, ebc0_cs4_bncr_value);
 
 	return;
 }
@@ -1939,10 +1939,10 @@ void configure_ppc440ep_pins(void)
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
 
-		mfsdr(sdr_usb0, sdr0_usb0);
+		mfsdr(SDR0_USB0, sdr0_usb0);
 		sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
 		sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB20D_DEVSEL;
-		mtsdr(sdr_usb0, sdr0_usb0);
+		mtsdr(SDR0_USB0, sdr0_usb0);
 
 		usb2_device_selection_in_fpga();
 	}
@@ -1950,19 +1950,19 @@ void configure_ppc440ep_pins(void)
 	/* USB1.1 Device Selection */
 	if (ppc440ep_core_selection[USB1_DEVICE] == CORE_SELECTED)
 	{
-		mfsdr(sdr_usb0, sdr0_usb0);
+		mfsdr(SDR0_USB0, sdr0_usb0);
 		sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
 		sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB11D_DEVSEL;
-		mtsdr(sdr_usb0, sdr0_usb0);
+		mtsdr(SDR0_USB0, sdr0_usb0);
 	}
 
 	/* USB1.1 Host Selection */
 	if (ppc440ep_core_selection[USB1_HOST] == CORE_SELECTED)
 	{
-		mfsdr(sdr_usb0, sdr0_usb0);
+		mfsdr(SDR0_USB0, sdr0_usb0);
 		sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_LEEN_MASK;
 		sdr0_usb0 = sdr0_usb0 | SDR0_USB0_LEEN_ENABLE;
-		mtsdr(sdr_usb0, sdr0_usb0);
+		mtsdr(SDR0_USB0, sdr0_usb0);
 	}
 
 	/* NAND Flash Selection */
@@ -1971,14 +1971,14 @@ void configure_ppc440ep_pins(void)
 		update_ndfc_ios(gpio_tab);
 
 #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
-		mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL   |
+		mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL   |
 		      SDR0_CUST0_NDFC_ENABLE	|
 		      SDR0_CUST0_NDFC_BW_8_BIT	|
 		      SDR0_CUST0_NDFC_ARE_MASK	|
 		      SDR0_CUST0_CHIPSELGAT_EN1 |
 		      SDR0_CUST0_CHIPSELGAT_EN2);
 #else
-		mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL   |
+		mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL   |
 		      SDR0_CUST0_NDFC_ENABLE	|
 		      SDR0_CUST0_NDFC_BW_8_BIT	|
 		      SDR0_CUST0_NDFC_ARE_MASK	|
@@ -1991,16 +1991,16 @@ void configure_ppc440ep_pins(void)
 	else
 	{
 		/* Set Mux on EMAC */
-		mtsdr(sdr_cust0, SDR0_CUST0_MUX_EMAC_SEL);
+		mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_EMAC_SEL);
 	}
 
 	/* MII Selection */
 	if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
 	{
 		update_zii_ios(gpio_tab);
-		mfsdr(sdr_mfr, sdr0_mfr);
+		mfsdr(SDR0_MFR, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
-		mtsdr(sdr_mfr, sdr0_mfr);
+		mtsdr(SDR0_MFR, sdr0_mfr);
 
 		set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_MII);
 	}
@@ -2009,9 +2009,9 @@ void configure_ppc440ep_pins(void)
 	if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
 	{
 		update_zii_ios(gpio_tab);
-		mfsdr(sdr_mfr, sdr0_mfr);
+		mfsdr(SDR0_MFR, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
-		mtsdr(sdr_mfr, sdr0_mfr);
+		mtsdr(SDR0_MFR, sdr0_mfr);
 
 		set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_RMII);
 	}
@@ -2020,9 +2020,9 @@ void configure_ppc440ep_pins(void)
 	if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
 	{
 		update_zii_ios(gpio_tab);
-		mfsdr(sdr_mfr, sdr0_mfr);
+		mfsdr(SDR0_MFR, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
-		mtsdr(sdr_mfr, sdr0_mfr);
+		mtsdr(SDR0_MFR, sdr0_mfr);
 
 		set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_SMII);
 	}
@@ -2071,13 +2071,13 @@ void configure_ppc440ep_pins(void)
 	/* Packet Reject Function Enable */
 	if (ppc440ep_core_selection[PACKET_REJ_FUNC_EN] == CORE_SELECTED)
 	{
-		mfsdr(sdr_mfr, sdr0_mfr);
+		mfsdr(SDR0_MFR, sdr0_mfr);
 		sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_PKT_REJ_MASK) | SDR0_MFR_PKT_REJ_EN;;
-		mtsdr(sdr_mfr, sdr0_mfr);
+		mtsdr(SDR0_MFR, sdr0_mfr);
 	}
 
 	/* Perform effective access to hardware */
-	mtsdr(sdr_pfc1, sdr0_pfc1);
+	mtsdr(SDR0_PFC1, sdr0_pfc1);
 	set_chip_gpio_configuration(GPIO0, gpio_tab);
 	set_chip_gpio_configuration(GPIO1, gpio_tab);
 

board/amcc/bamboo/flash.c

@@ -94,7 +94,7 @@ unsigned long flash_init(void)
 		 * Boot Settings in IIC EEprom address 0xA8 or 0xA4
 		 * Read Serial Device Strap Register1 in PPC440EP
 		 */
-		mfsdr(sdr_sdstp1, val);
+		mfsdr(SDR0_SDSTP1, val);
 		boot_selection  = val & SDR0_SDSTP1_BOOT_SEL_MASK;
 		ebc_boot_size   = val & SDR0_SDSTP1_EBC_ROM_BS_MASK;
 

board/amcc/bubinga/bubinga.c

@@ -41,9 +41,9 @@ int board_early_init_f(void)
 	 * and enable the internal PCI arbiter if selected
 	 */
 	if (in_8((void *)FPGA_REG1) & FPGA_REG1_PCI_INT_ARB)
-		mtdcr(cpc0_pci, CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
+		mtdcr(CPC0_PCI, CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
 	else
-		mtdcr(cpc0_pci, CPC0_PCI_HOST_CFG_EN);
+		mtdcr(CPC0_PCI, CPC0_PCI_HOST_CFG_EN);
 
 	return 0;
 }

board/amcc/bubinga/flash.c

@@ -106,25 +106,25 @@ unsigned long flash_init(void)
 		/* Re-do sizing to get full correct info */
 
 		if (size_b1) {
-			mtdcr(ebccfga, pb0cr);
+			mtdcr(EBC0_CFGADDR, PB0CR);
-			pbcr = mfdcr(ebccfgd);
+			pbcr = mfdcr(EBC0_CFGDATA);
-			mtdcr(ebccfga, pb0cr);
+			mtdcr(EBC0_CFGADDR, PB0CR);
 			base_b1 = -size_b1;
 			pbcr = (pbcr & 0x0001ffff) | base_b1 |
 			    (((size_b1 / 1024 / 1024) - 1) << 17);
-			mtdcr(ebccfgd, pbcr);
+			mtdcr(EBC0_CFGDATA, pbcr);
-			/*          printf("pb1cr = %x\n", pbcr); */
+			/*          printf("PB1CR = %x\n", pbcr); */
 		}
 
 		if (size_b0) {
-			mtdcr(ebccfga, pb1cr);
+			mtdcr(EBC0_CFGADDR, PB1CR);
-			pbcr = mfdcr(ebccfgd);
+			pbcr = mfdcr(EBC0_CFGDATA);
-			mtdcr(ebccfga, pb1cr);
+			mtdcr(EBC0_CFGADDR, PB1CR);
 			base_b0 = base_b1 - size_b0;
 			pbcr = (pbcr & 0x0001ffff) | base_b0 |
 			    (((size_b0 / 1024 / 1024) - 1) << 17);
-			mtdcr(ebccfgd, pbcr);
+			mtdcr(EBC0_CFGDATA, pbcr);
-			/*            printf("pb0cr = %x\n", pbcr); */
+			/*            printf("PB0CR = %x\n", pbcr); */
 		}
 
 		size_b0 = flash_get_size((vu_long *) base_b0, &flash_info[0]);

board/amcc/canyonlands/canyonlands.c

@@ -475,9 +475,9 @@ int board_early_init_r (void)
 
 	/* Remap the NOR FLASH to 0xcc00.0000 ... 0xcfff.ffff */
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtebc(pb3cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
+	mtebc(PB3CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
 #else
-	mtebc(pb0cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
+	mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
 #endif
 
 	/* Remove TLB entry of boot EBC mapping */

board/amcc/ebony/ebony.c

@@ -41,30 +41,30 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup the external bus controller/chip selects
 	 *-------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(ebccfgd);
+	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfgd, reg | 0x04000000);	/* Set ATC */
+	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
 
-	mtebc(pb1ap, 0x02815480);	/* NVRAM/RTC */
+	mtebc(PB1AP, 0x02815480);	/* NVRAM/RTC */
-	mtebc(pb1cr, 0x48018000);	/* BA=0x480 1MB R/W 8-bit */
+	mtebc(PB1CR, 0x48018000);	/* BA=0x480 1MB R/W 8-bit */
-	mtebc(pb7ap, 0x01015280);	/* FPGA registers */
+	mtebc(PB7AP, 0x01015280);	/* FPGA registers */
-	mtebc(pb7cr, 0x48318000);	/* BA=0x483 1MB R/W 8-bit */
+	mtebc(PB7CR, 0x48318000);	/* BA=0x483 1MB R/W 8-bit */
 
 	/* read FPGA_REG0  and set the bus controller */
 	status = *fpga_base;
 	if ((status & BOOT_SMALL_FLASH) && !(status & FLASH_ONBD_N)) {
-		mtebc(pb0ap, 0x9b015480);	/* FLASH/SRAM */
+		mtebc(PB0AP, 0x9b015480);	/* FLASH/SRAM */
-		mtebc(pb0cr, 0xfff18000);	/* BAS=0xfff 1MB R/W 8-bit */
+		mtebc(PB0CR, 0xfff18000);	/* BAS=0xfff 1MB R/W 8-bit */
-		mtebc(pb2ap, 0x9b015480);	/* 4MB FLASH */
+		mtebc(PB2AP, 0x9b015480);	/* 4MB FLASH */
-		mtebc(pb2cr, 0xff858000);	/* BAS=0xff8 4MB R/W 8-bit */
+		mtebc(PB2CR, 0xff858000);	/* BAS=0xff8 4MB R/W 8-bit */
 	} else {
-		mtebc(pb0ap, 0x9b015480);	/* 4MB FLASH */
+		mtebc(PB0AP, 0x9b015480);	/* 4MB FLASH */
-		mtebc(pb0cr, 0xffc58000);	/* BAS=0xffc 4MB R/W 8-bit */
+		mtebc(PB0CR, 0xffc58000);	/* BAS=0xffc 4MB R/W 8-bit */
 
 		/* set CS2 if FLASH_ONBD_N == 0 */
 		if (!(status & FLASH_ONBD_N)) {
-			mtebc(pb2ap, 0x9b015480);	/* FLASH/SRAM */
+			mtebc(PB2AP, 0x9b015480);	/* FLASH/SRAM */
-			mtebc(pb2cr, 0xff818000);	/* BAS=0xff8 4MB R/W 8-bit */
+			mtebc(PB2CR, 0xff818000);	/* BAS=0xff8 4MB R/W 8-bit */
 		}
 	}
 
@@ -186,7 +186,7 @@ int pci_pre_init(struct pci_controller *hose)
 	 * The ebony board is always configured as the host & requires the
 	 * PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	strap = mfdcr(cpc0_strp1);
+	strap = mfdcr(CPC0_STRP1);
 	if ((strap & 0x00100000) == 0) {
 		printf("PCI: CPC0_STRP1[PAE] not set.\n");
 		return 0;

board/amcc/katmai/katmai.c

@@ -220,9 +220,9 @@ int board_early_init_f (void)
 	mtdcr (uic0sr, 0x00000000);	/* clear all interrupts*/
 	mtdcr (uic0sr, 0xffffffff);	/* clear all interrupts*/
 
-	mfsdr(sdr_mfr, mfr);
+	mfsdr(SDR0_MFR, mfr);
 	mfr |= SDR0_MFR_FIXD;		/* Workaround for PCI/DMA */
-	mtsdr(sdr_mfr, mfr);
+	mtsdr(SDR0_MFR, mfr);
 
 	mtsdr(SDR0_PFC0, CONFIG_SYS_PFC0);
 
@@ -280,7 +280,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The katmai board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *-------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;

board/amcc/luan/luan.c

@@ -42,12 +42,12 @@ int board_early_init_f(void)
 {
 	u32 mfr;
 
-	mtebc( pb0ap,  0x03800000 );	/* set chip selects */
+	mtebc( PB0AP,  0x03800000 );	/* set chip selects */
-	mtebc( pb0cr,  0xffc58000 );	/* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
+	mtebc( PB0CR,  0xffc58000 );	/* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
-	mtebc( pb1ap,  0x03800000 );
+	mtebc( PB1AP,  0x03800000 );
-	mtebc( pb1cr,  0xff018000 );	/* ebc0_b1cr, 1MB at 0xff000000 CS1 */
+	mtebc( PB1CR,  0xff018000 );	/* ebc0_b1cr, 1MB at 0xff000000 CS1 */
-	mtebc( pb2ap,  0x03800000 );
+	mtebc( PB2AP,  0x03800000 );
-	mtebc( pb2cr,  0xff838000 );	/* ebc0_b2cr, 2MB at 0xff800000 CS2 */
+	mtebc( PB2CR,  0xff838000 );	/* ebc0_b2cr, 2MB at 0xff800000 CS2 */
 
 	mtdcr( uic1sr, 0xffffffff );	/* Clear all interrupts */
 	mtdcr( uic1er, 0x00000000 );	/* disable all interrupts */
@@ -67,9 +67,9 @@ int board_early_init_f(void)
 	mtdcr( uic0sr, 0x00000000 );	/* clear all interrupts */
 	mtdcr( uic0sr, 0xffffffff );
 
-	mfsdr(sdr_mfr, mfr);
+	mfsdr(SDR0_MFR, mfr);
 	mfr |= SDR0_MFR_FIXD;		/* Workaround for PCI/DMA */
-	mtsdr(sdr_mfr, mfr);
+	mtsdr(SDR0_MFR, mfr);
 
 	return  0;
 }
@@ -147,7 +147,7 @@ int pci_pre_init( struct pci_controller *hose )
 	 *	The luan board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 

board/amcc/ocotea/ocotea.c

@@ -54,7 +54,7 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------+
 	  | Initialize EBC CONFIG
 	  +-------------------------------------------------------------------------*/
-	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
 	      EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
 	      EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
 	      EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
@@ -63,14 +63,14 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------+
 	  | FPGA. Initialize bank 7 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb7ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
+	mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
 	      EBC_BXAP_BCE_DISABLE|
 	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
 	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
 	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
 	      EBC_BXAP_BEM_WRITEONLY|
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48300000)|
+	mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
 	      EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/* read FPGA base register FPGA_REG0 */
@@ -95,53 +95,53 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------+
 	  | 1 MB FLASH / 1 MB SRAM. Initialize bank 0 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb0ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs0_twt)|
+	mtebc(PB0AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs0_twt)|
 	      EBC_BXAP_BCE_DISABLE|
 	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
 	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
 	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
 	      EBC_BXAP_BEM_WRITEONLY|
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(cs0_base)|
+	mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(cs0_base)|
 	      cs0_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | 8KB NVRAM/RTC. Initialize bank 1 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb1ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
+	mtebc(PB1AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
 	      EBC_BXAP_BCE_DISABLE|
 	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
 	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
 	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
 	      EBC_BXAP_BEM_WRITEONLY|
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000)|
+	mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000)|
 	      EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | 4 MB FLASH. Initialize bank 2 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb2ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs2_twt)|
+	mtebc(PB2AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs2_twt)|
 	      EBC_BXAP_BCE_DISABLE|
 	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
 	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
 	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
 	      EBC_BXAP_BEM_WRITEONLY|
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(cs2_base)|
+	mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(cs2_base)|
 	      cs2_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | FPGA. Initialize bank 7 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb7ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
+	mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
 	      EBC_BXAP_BCE_DISABLE|
 	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
 	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
 	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
 	      EBC_BXAP_BEM_WRITEONLY|
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48300000)|
+	mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
 	      EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/*--------------------------------------------------------------------
@@ -189,9 +189,9 @@ int board_early_init_f (void)
 	mtdcr (uic0pr, 0xfc000000); /* */
 	mtdcr (uic0tr, 0x00000000); /* */
 	mtdcr (uic0vr, 0x00000001); /* */
-	mfsdr (sdr_mfr, mfr);
+	mfsdr (SDR0_MFR, mfr);
 	mfr &= ~SDR0_MFR_ECS_MASK;
-/*	mtsdr(sdr_mfr, mfr); */
+/*	mtsdr(SDR0_MFR, mfr); */
 	fpga_init();
 
 	return 0;
@@ -297,7 +297,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The ocotea board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;
@@ -379,8 +379,8 @@ void fpga_init(void)
 	unsigned long sdr0_cust0;
 	unsigned long pvr;
 
-	mfsdr (sdr_pfc0, sdr0_pfc0);
+	mfsdr (SDR0_PFC0, sdr0_pfc0);
-	mfsdr (sdr_pfc1, sdr0_pfc1);
+	mfsdr (SDR0_PFC1, sdr0_pfc1);
 	group = SDR0_PFC1_EPS_DECODE(sdr0_pfc1);
 	pvr = get_pvr ();
 
@@ -390,8 +390,8 @@ void fpga_init(void)
 		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
 		out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
 		     FPGA_REG2_EXT_INTFACE_ENABLE);
-		mtsdr (sdr_pfc0, sdr0_pfc0);
+		mtsdr (SDR0_PFC0, sdr0_pfc0);
-		mtsdr (sdr_pfc1, sdr0_pfc1);
+		mtsdr (SDR0_PFC1, sdr0_pfc1);
 	} else {
 		sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_ENABLE;
 		switch (group)
@@ -403,8 +403,8 @@ void fpga_init(void)
 			out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
 			     FPGA_REG2_EXT_INTFACE_ENABLE);
 			sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
-			mtsdr (sdr_pfc0, sdr0_pfc0);
+			mtsdr (SDR0_PFC0, sdr0_pfc0);
-			mtsdr (sdr_pfc1, sdr0_pfc1);
+			mtsdr (SDR0_PFC1, sdr0_pfc1);
 			break;
 		case 3:
 		case 4:
@@ -412,8 +412,8 @@ void fpga_init(void)
 		case 6:
 			/* CPU trace B - Over EBMI */
 			sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_CPUTRACE;
-			mtsdr (sdr_pfc0, sdr0_pfc0);
+			mtsdr (SDR0_PFC0, sdr0_pfc0);
-			mtsdr (sdr_pfc1, sdr0_pfc1);
+			mtsdr (SDR0_PFC1, sdr0_pfc1);
 			out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
 			     FPGA_REG2_EXT_INTFACE_DISABLE);
 			break;
@@ -421,8 +421,8 @@ void fpga_init(void)
 	}
 
 	/* Initialize the ethernet specific functions in the fpga */
-	mfsdr(sdr_pfc1, sdr0_pfc1);
+	mfsdr(SDR0_PFC1, sdr0_pfc1);
-	mfsdr(sdr_cust0, sdr0_cust0);
+	mfsdr(SDR0_CUST0, sdr0_cust0);
 	if ( (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) == 4) &&
 	    ((SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII) ||
 	     (SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_TBI)))

board/amcc/redwood/redwood.c

@@ -220,7 +220,7 @@ static void early_init_EBC(void)
 	 * default value :
 	 *      0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
 	 */
-	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
 	      EBC_CFG_PTD_ENABLE |
 	      EBC_CFG_RTC_16PERCLK |
 	      EBC_CFG_ATC_PREVIOUS |
@@ -237,8 +237,8 @@ static void early_init_EBC(void)
 	 * since some board registers values may be needed to determine the
 	 * boot type
 	 */
-	mtebc(pb1ap, EBC_BXAP_FPGA);
+	mtebc(PB1AP, EBC_BXAP_FPGA);
-	mtebc(pb1cr, EBC_BXCR_FPGA_CS3);
+	mtebc(PB1CR, EBC_BXCR_FPGA_CS3);
 
 }
 
@@ -399,12 +399,12 @@ static void early_reinit_EBC(int computed_boot_device)
 		break;
 	}
 
-	mtebc(pb0ap, ebc0_cs0_bxap_value);
+	mtebc(PB0AP, ebc0_cs0_bxap_value);
-	mtebc(pb0cr, ebc0_cs0_bxcr_value);
+	mtebc(PB0CR, ebc0_cs0_bxcr_value);
-	mtebc(pb1ap, ebc0_cs1_bxap_value);
+	mtebc(PB1AP, ebc0_cs1_bxap_value);
-	mtebc(pb1cr, ebc0_cs1_bxcr_value);
+	mtebc(PB1CR, ebc0_cs1_bxcr_value);
-	mtebc(pb2ap, ebc0_cs2_bxap_value);
+	mtebc(PB2AP, ebc0_cs2_bxap_value);
-	mtebc(pb2cr, ebc0_cs2_bxcr_value);
+	mtebc(PB2CR, ebc0_cs2_bxcr_value);
 }
 
 static void early_init_UIC(void)

board/amcc/sequoia/sequoia.c

@@ -46,8 +46,8 @@ int board_early_init_f(void)
 	u32 sdr0_pfc1, sdr0_pfc2;
 	u32 reg;
 
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, 0xb8400000);
+	mtdcr(EBC0_CFGDATA, 0xb8400000);
 
 	/*
 	 * Setup the interrupt controller polarities, triggers, etc.
@@ -107,8 +107,8 @@ int board_early_init_f(void)
 	mtsdr(SDR0_PFC1, sdr0_pfc1);
 
 	/* PCI arbiter enabled */
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);
 
 	/* setup NAND FLASH */
 	mfsdr(SDR0_CUST0, sdr0_cust0);
@@ -144,19 +144,19 @@ int misc_init_r(void)
 	gd->bd->bi_flashoffset = 0;
 
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtdcr(ebccfga, pb3cr);
+	mtdcr(EBC0_CFGADDR, PB3CR);
 #else
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 #endif
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	size_val = ffs(gd->bd->bi_flashsize) - 21;
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtdcr(ebccfga, pb3cr);
+	mtdcr(EBC0_CFGADDR, PB3CR);
 #else
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 #endif
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/*
 	 * Re-check to get correct base address
@@ -309,8 +309,8 @@ int misc_init_r(void)
 	 * This fix will make the MAL burst disabling patch for the Linux
 	 * EMAC driver obsolete.
 	 */
-	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
-	mtdcr(plb4_acr, reg);
+	mtdcr(PLB4_ACR, reg);
 
 	return 0;
 }
@@ -370,35 +370,35 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*
 	 * Set Nebula PLB4 arbiter to fair mode.
 	 */
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 #ifdef CONFIG_PCI_PNP
 	hose->fixup_irq = sequoia_pci_fixup_irq;

board/amcc/taihu/taihu.c

@@ -48,14 +48,14 @@ int board_early_init_f(void)
 	mtdcr(uicsr, 0xFFFFFFFF);	/* clear all ints */
 	mtdcr(uicvcr, 0x00000001);	/* set vect base=0,INT0 highest priority */
 
-	mtebc(pb3ap, CONFIG_SYS_EBC_PB3AP);	/* memory bank 3 (CPLD_LCM) initialization */
+	mtebc(PB3AP, CONFIG_SYS_EBC_PB3AP);	/* memory bank 3 (CPLD_LCM) initialization */
-	mtebc(pb3cr, CONFIG_SYS_EBC_PB3CR);
+	mtebc(PB3CR, CONFIG_SYS_EBC_PB3CR);
 
 	/*
 	 * Configure CPC0_PCI to enable PerWE as output
 	 * and enable the internal PCI arbiter
 	 */
-	mtdcr(cpc0_pci, CPC0_PCI_SPE | CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
+	mtdcr(CPC0_PCI, CPC0_PCI_SPE | CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
 
 	return 0;
 }

board/amcc/taishan/showinfo.c

@@ -33,60 +33,60 @@ void show_reset_reg(void)
 
 	/* read clock regsiter */
 	printf("===== Display reset and initialize register Start =========\n");
-	mfcpr(clk_pllc,reg);
+	mfcpr(CPR0_PLLC,reg);
 	printf("cpr_pllc   = %#010lx\n",reg);
 
-	mfcpr(clk_plld,reg);
+	mfcpr(CPR0_PLLD,reg);
 	printf("cpr_plld   = %#010lx\n",reg);
 
-	mfcpr(clk_primad,reg);
+	mfcpr(CPR0_PRIMAD,reg);
 	printf("cpr_primad = %#010lx\n",reg);
 
-	mfcpr(clk_primbd,reg);
+	mfcpr(CPR0_PRIMBD,reg);
 	printf("cpr_primbd = %#010lx\n",reg);
 
-	mfcpr(clk_opbd,reg);
+	mfcpr(CPR0_OPBD,reg);
 	printf("cpr_opbd   = %#010lx\n",reg);
 
-	mfcpr(clk_perd,reg);
+	mfcpr(CPR0_PERD,reg);
 	printf("cpr_perd   = %#010lx\n",reg);
 
-	mfcpr(clk_mald,reg);
+	mfcpr(CPR0_MALD,reg);
 	printf("cpr_mald   = %#010lx\n",reg);
 
 	/* read sdr register */
-	mfsdr(sdr_ebc,reg);
+	mfsdr(SDR0_EBC,reg);
-	printf("sdr_ebc    = %#010lx\n",reg);
+	printf("SDR0_EBC    = %#010lx\n",reg);
 
-	mfsdr(sdr_cp440,reg);
+	mfsdr(SDR0_CP440,reg);
-	printf("sdr_cp440  = %#010lx\n",reg);
+	printf("SDR0_CP440  = %#010lx\n",reg);
 
-	mfsdr(sdr_xcr,reg);
+	mfsdr(SDR0_XCR,reg);
-	printf("sdr_xcr    = %#010lx\n",reg);
+	printf("SDR0_XCR    = %#010lx\n",reg);
 
-	mfsdr(sdr_xpllc,reg);
+	mfsdr(SDR0_XPLLC,reg);
-	printf("sdr_xpllc  = %#010lx\n",reg);
+	printf("SDR0_XPLLC  = %#010lx\n",reg);
 
-	mfsdr(sdr_xplld,reg);
+	mfsdr(SDR0_XPLLD,reg);
-	printf("sdr_xplld  = %#010lx\n",reg);
+	printf("SDR0_XPLLD  = %#010lx\n",reg);
 
-	mfsdr(sdr_pfc0,reg);
+	mfsdr(SDR0_PFC0,reg);
-	printf("sdr_pfc0   = %#010lx\n",reg);
+	printf("SDR0_PFC0   = %#010lx\n",reg);
 
-	mfsdr(sdr_pfc1,reg);
+	mfsdr(SDR0_PFC1,reg);
-	printf("sdr_pfc1   = %#010lx\n",reg);
+	printf("SDR0_PFC1   = %#010lx\n",reg);
 
-	mfsdr(sdr_cust0,reg);
+	mfsdr(SDR0_CUST0,reg);
-	printf("sdr_cust0  = %#010lx\n",reg);
+	printf("SDR0_CUST0  = %#010lx\n",reg);
 
-	mfsdr(sdr_cust1,reg);
+	mfsdr(SDR0_CUST1,reg);
-	printf("sdr_cust1  = %#010lx\n",reg);
+	printf("SDR0_CUST1  = %#010lx\n",reg);
 
-	mfsdr(sdr_uart0,reg);
+	mfsdr(SDR0_UART0,reg);
-	printf("sdr_uart0  = %#010lx\n",reg);
+	printf("SDR0_UART0  = %#010lx\n",reg);
 
-	mfsdr(sdr_uart1,reg);
+	mfsdr(SDR0_UART1,reg);
-	printf("sdr_uart1  = %#010lx\n",reg);
+	printf("SDR0_UART1  = %#010lx\n",reg);
 
 	printf("===== Display reset and initialize register End   =========\n");
 }
@@ -96,14 +96,14 @@ void show_xbridge_info(void)
 	unsigned long reg;
 
 	printf("PCI-X chip control registers\n");
-	mfsdr(sdr_xcr, reg);
+	mfsdr(SDR0_XCR, reg);
-	printf("sdr_xcr    = %#010lx\n", reg);
+	printf("SDR0_XCR    = %#010lx\n", reg);
 
-	mfsdr(sdr_xpllc, reg);
+	mfsdr(SDR0_XPLLC, reg);
-	printf("sdr_xpllc  = %#010lx\n", reg);
+	printf("SDR0_XPLLC  = %#010lx\n", reg);
 
-	mfsdr(sdr_xplld, reg);
+	mfsdr(SDR0_XPLLD, reg);
-	printf("sdr_xplld  = %#010lx\n", reg);
+	printf("SDR0_XPLLD  = %#010lx\n", reg);
 
 	printf("PCI-X Bridge Configure registers\n");
 	printf("PCIX0_VENDID            = %#06x\n", in16r(PCIX0_VENDID));

board/amcc/taishan/taishan.c

@@ -47,7 +47,7 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------+
 	  | Initialize EBC CONFIG
 	  +-------------------------------------------------------------------------*/
-	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
 	      EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
 	      EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
 	      EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_DEFAULT |
@@ -56,66 +56,66 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------+
 	  | 64MB FLASH. Initialize bank 0 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb0ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(15) |
+	mtebc(PB0AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(15) |
 	      EBC_BXAP_BCE_DISABLE |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1) |
 	      EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) |
 	      EBC_BXAP_TH_ENCODE(3) | EBC_BXAP_RE_DISABLED |
 	      EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+	mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
 	      EBC_BXCR_BS_64MB | EBC_BXCR_BU_RW|EBC_BXCR_BW_32BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | FPGA. Initialize bank 1 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb1ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(5) |
+	mtebc(PB1AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(5) |
 	      EBC_BXAP_BCE_DISABLE |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1) |
 	      EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) |
 	      EBC_BXAP_TH_ENCODE(3) | EBC_BXAP_RE_DISABLED |
 	      EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x41000000) |
+	mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x41000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | LCM. Initialize bank 2 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb2ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(64) |
+	mtebc(PB2AP, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(64) |
 	      EBC_BXAP_BCE_DISABLE |
 	      EBC_BXAP_CSN_ENCODE(3) | EBC_BXAP_OEN_ENCODE(3) |
 	      EBC_BXAP_WBN_ENCODE(3) | EBC_BXAP_WBF_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(7) | EBC_BXAP_RE_DISABLED |
 	      EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0x42000000) |
+	mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0x42000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | TMP. Initialize bank 3 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb3ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(128) |
+	mtebc(PB3AP, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(128) |
 	      EBC_BXAP_BCE_DISABLE |
 	      EBC_BXAP_CSN_ENCODE(3) | EBC_BXAP_OEN_ENCODE(3) |
 	      EBC_BXAP_WBN_ENCODE(3) | EBC_BXAP_WBF_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(7) | EBC_BXAP_RE_DISABLED |
 	      EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
-	mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+	mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
 	      EBC_BXCR_BS_64MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*-------------------------------------------------------------------------+
 	  | Connector 4~7. Initialize bank 3~ 7 with default values.
 	  +-------------------------------------------------------------------------*/
-	mtebc(pb4ap,0);
+	mtebc(PB4AP,0);
-	mtebc(pb4cr,0);
+	mtebc(PB4CR,0);
-	mtebc(pb5ap,0);
+	mtebc(PB5AP,0);
-	mtebc(pb5cr,0);
+	mtebc(PB5CR,0);
-	mtebc(pb6ap,0);
+	mtebc(PB6AP,0);
-	mtebc(pb6cr,0);
+	mtebc(PB6CR,0);
-	mtebc(pb7ap,0);
+	mtebc(PB7AP,0);
-	mtebc(pb7cr,0);
+	mtebc(PB7CR,0);
 
 	/*--------------------------------------------------------------------
 	 * Setup the interrupt controller polarities, triggers, etc.
@@ -164,13 +164,13 @@ int board_early_init_f (void)
 	mtdcr (uic0vr, 0x00000001);	/* */
 
 	/* Enable two GPIO 10~11 and TraceA signal */
-	mfsdr(sdr_pfc0,reg);
+	mfsdr(SDR0_PFC0,reg);
 	reg |= 0x00300000;
-	mtsdr(sdr_pfc0,reg);
+	mtsdr(SDR0_PFC0,reg);
 
-	mfsdr(sdr_pfc1,reg);
+	mfsdr(SDR0_PFC1,reg);
 	reg |= 0x00100000;
-	mtsdr(sdr_pfc1,reg);
+	mtsdr(SDR0_PFC1,reg);
 
 	/* Set GPIO 10 and 11 as output */
 	GpioOdr	= (volatile unsigned int*)(CONFIG_SYS_PERIPHERAL_BASE+0x718);
@@ -230,7 +230,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The ocotea board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;

board/amcc/walnut/flash.c

@@ -102,27 +102,27 @@ unsigned long flash_init(void)
 		/* Re-do sizing to get full correct info */
 
 		if (size_b1) {
-			mtdcr(ebccfga, pb0cr);
+			mtdcr(EBC0_CFGADDR, PB0CR);
-			pbcr = mfdcr(ebccfgd);
+			pbcr = mfdcr(EBC0_CFGDATA);
-			mtdcr(ebccfga, pb0cr);
+			mtdcr(EBC0_CFGADDR, PB0CR);
 			base_b1 = -size_b1;
 			pbcr =
 			    (pbcr & 0x0001ffff) | base_b1 |
 			    (((size_b1 / 1024 / 1024) - 1) << 17);
-			mtdcr(ebccfgd, pbcr);
+			mtdcr(EBC0_CFGDATA, pbcr);
-			/*          printf("pb1cr = %x\n", pbcr); */
+			/*          printf("PB1CR = %x\n", pbcr); */
 		}
 
 		if (size_b0) {
-			mtdcr(ebccfga, pb1cr);
+			mtdcr(EBC0_CFGADDR, PB1CR);
-			pbcr = mfdcr(ebccfgd);
+			pbcr = mfdcr(EBC0_CFGDATA);
-			mtdcr(ebccfga, pb1cr);
+			mtdcr(EBC0_CFGADDR, PB1CR);
 			base_b0 = base_b1 - size_b0;
 			pbcr =
 			    (pbcr & 0x0001ffff) | base_b0 |
 			    (((size_b0 / 1024 / 1024) - 1) << 17);
-			mtdcr(ebccfgd, pbcr);
+			mtdcr(EBC0_CFGDATA, pbcr);
-			/*            printf("pb0cr = %x\n", pbcr); */
+			/*            printf("PB0CR = %x\n", pbcr); */
 		}
 
 		size_b0 = flash_get_size((vu_long *) base_b0, &flash_info[0]);

board/amcc/yosemite/yosemite.c

@@ -40,9 +40,9 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup the external bus controller/chip selects
 	 *-------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(ebccfgd);
+	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfgd, reg | 0x04000000);	/* Set ATC */
+	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
 
 	/*--------------------------------------------------------------------
 	 * Setup the GPIO pins
@@ -101,10 +101,10 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup other serial configuration
 	 *-------------------------------------------------------------------*/
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);	/* PCI arbiter enabled */
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);	/* PCI arbiter enabled */
-	mtsdr(sdr_pfc0, 0x00003e00);	/* Pin function */
+	mtsdr(SDR0_PFC0, 0x00003e00);	/* Pin function */
-	mtsdr(sdr_pfc1, 0x00048000);	/* Pin function: UART0 has 4 pins */
+	mtsdr(SDR0_PFC1, 0x00048000);	/* Pin function: UART0 has 4 pins */
 
 	/*clear tmrclk divisor */
 	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00;
@@ -129,8 +129,8 @@ int misc_init_r (void)
 	int size_val = 0;
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	switch (gd->bd->bi_flashsize) {
 	case 1 << 20:
 		size_val = 0;
@@ -158,8 +158,8 @@ int misc_init_r (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -353,35 +353,35 @@ int pci_pre_init(struct pci_controller *hose)
 	  | Set priority for all PLB3 devices to 0.
 	  | Set PLB3 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*-------------------------------------------------------------------------+
 	  | Set priority for all PLB4 devices to 0.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*-------------------------------------------------------------------------+
 	  | Set Nebula PLB4 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	return 1;
 }

board/amcc/yucca/flash.c

@@ -981,7 +981,7 @@ unsigned long flash_init(void)
 		 * Boot Settings in IIC EEprom address 0xA8 or 0xA0
 		 * Read Serial Device Strap Register1 in PPC440SPe
 		 */
-		mfsdr(sdr_sdstp1, val);
+		mfsdr(SDR0_SDSTP1, val);
 		boot_selection  = val & SDR0_SDSTP1_BOOT_SEL_MASK;
 		ebc_boot_size   = val & SDR0_SDSTP1_EBC_ROM_BS_MASK;
 

board/amcc/yucca/yucca.c

@@ -167,7 +167,7 @@ int board_early_init_f (void)
 	 |	0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
 	 |
 	 +-------------------------------------------------------------------*/
-	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
 			EBC_CFG_PTD_ENABLE |
 			EBC_CFG_RTC_16PERCLK |
 			EBC_CFG_ATC_PREVIOUS |
@@ -188,8 +188,8 @@ int board_early_init_f (void)
 	 | boot type
 	 |
 	 +-------------------------------------------------------------------*/
-	mtebc(pb1ap, EBC_BXAP_FPGA);
+	mtebc(PB1AP, EBC_BXAP_FPGA);
-	mtebc(pb1cr, EBC_BXCR_FPGA_CS1);
+	mtebc(PB1CR, EBC_BXCR_FPGA_CS1);
 
 	/*-------------------------------------------------------------------+
 	 |
@@ -334,10 +334,10 @@ int board_early_init_f (void)
 			break;
 	}
 
-	mtebc(pb0ap, ebc0_cs0_bxap_value);
+	mtebc(PB0AP, ebc0_cs0_bxap_value);
-	mtebc(pb0cr, ebc0_cs0_bxcr_value);
+	mtebc(PB0CR, ebc0_cs0_bxcr_value);
-	mtebc(pb2ap, ebc0_cs2_bxap_value);
+	mtebc(PB2AP, ebc0_cs2_bxap_value);
-	mtebc(pb2cr, ebc0_cs2_bxcr_value);
+	mtebc(PB2CR, ebc0_cs2_bxcr_value);
 
 	/*--------------------------------------------------------------------+
 	 | Interrupt controller setup for the AMCC 440SPe Evaluation board.
@@ -530,9 +530,9 @@ int board_early_init_f (void)
 	mtdcr (uic0sr, 0x00000000);	/* clear all interrupts */
 	mtdcr (uic0sr, 0xffffffff);	/* clear all interrupts */
 
-	mfsdr(sdr_mfr, mfr);
+	mfsdr(SDR0_MFR, mfr);
 	mfr |= SDR0_MFR_FIXD;		/* Workaround for PCI/DMA */
-	mtsdr(sdr_mfr, mfr);
+	mtsdr(SDR0_MFR, mfr);
 
 	fpga_init();
 
@@ -608,7 +608,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The yucca board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *-------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;

board/cray/L1/L1.c

@@ -198,8 +198,8 @@ static void init_sdram (void)
  unsigned long tmp;
 
 	/* write SDRAM bank 0 register */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	mtdcr (memcfgd, 0x00062001);
+	mtdcr (SDRAM0_CFGDATA, 0x00062001);
 
 /* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR.	*/
 /* To set the appropriate timings, we need to know the SDRAM speed.	*/
@@ -212,26 +212,26 @@ static void init_sdram (void)
 	/* divisor = ((mfdcr(strap)>> 28) & 0x3); */
 
 /* write SDRAM timing for 100MHz. */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	mtdcr (memcfgd, 0x0086400D);
+	mtdcr (SDRAM0_CFGDATA, 0x0086400D);
 
 /* write SDRAM refresh interval register */
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	mtdcr (memcfgd, 0x05F00000);
+	mtdcr (SDRAM0_CFGDATA, 0x05F00000);
 	udelay (200);
 
 /* sdram controller.*/
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	mtdcr (memcfgd, 0x90800000);
+	mtdcr (SDRAM0_CFGDATA, 0x90800000);
 	udelay (200);
 
 /* initially, disable ECC on all banks */
 	udelay (200);
-	mtdcr (memcfga, mem_ecccf);
+	mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	tmp &= 0xff0fffff;
-	mtdcr (memcfga, mem_ecccf);
+	mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 
 	return;
 }
@@ -282,18 +282,18 @@ int testdram (void)
 	}
 	printf ("Enable ECC..");
 
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
+	tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 	udelay (600);
 	for (p = (unsigned long) 0; ((unsigned long) p < L1_MEMSIZE); *p++ = 0L)
 		;
 	udelay (400);
-	mtdcr (memcfga, mem_ecccf);
+	mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	tmp |= 0x00800000;
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 	udelay (400);
 	printf ("enabled.\n");
 	return (0);

board/cray/L1/init.S

@@ -87,17 +87,17 @@ ext_bus_cntlr_init:
 	/* Peripheral Bank 0 (Flash) initialization */
 	/*---------------------------------------------------------------------- */
 		/* 0x7F8FFE80 slowest boot */
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0x9B01
 	ori     r4,r4,0x5480
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0xFFC5           /* BAS=0xFFC,BS=0x4(4MB),BU=0x3(R/W), */
 	ori     r4,r4,0x8000          /* BW=0x0( 8 bits) */
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	blr
 
@@ -125,16 +125,16 @@ ext_bus_cntlr_init:
 		/* all reserved bits=0 */
 	/*---------------------------------------------------------------------- */
 	/*---------------------------------------------------------------------- */
-	addi    r4,0,pb1ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0x0185		/* hiword */
 	ori     r4,r4,0x4380	/* loword */
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb1cr
+	addi    r4,0,PB1CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0xF001           /* BAS=0xF00,BS=0x0(1MB),BU=0x3(R/W), */
 	ori     r4,r4,0x8000          /* BW=0x0( 8 bits) */
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	blr

board/csb272/csb272.c

@@ -95,7 +95,7 @@ int board_early_init_f(void)
 	mtdcr (uicvcr, 0x00000001);  /* set vect base=0,INT0 highest priority */
 	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
 
-	mtebc (epcr, 0xa8400000);   /* EBC always driven */
+	mtebc (EBC0_CFG, 0xa8400000);   /* EBC always driven */
 
 	return 0; /* success */
 }
@@ -135,29 +135,29 @@ phys_size_t initdram (int board_type)
 
 	tot_size = 0;
 
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;

board/csb272/init.S

@@ -38,17 +38,17 @@
 
 #define WDCR_EBC(reg,val) \
 	addi    r4,0,reg;\
-	mtdcr   ebccfga,r4;\
+	mtdcr   EBC0_CFGADDR,r4;\
 	addis   r4,0,val@h;\
 	ori     r4,r4,val@l;\
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 #define WDCR_SDRAM(reg,val) \
 	addi    r4,0,reg;\
-	mtdcr   memcfga,r4;\
+	mtdcr   SDRAM0_CFGADDR,r4;\
 	addis   r4,0,val@h;\
 	ori     r4,r4,val@l;\
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 /******************************************************************************
  * Function:	ext_bus_cntlr_init
@@ -106,51 +106,51 @@ ext_bus_cntlr_init:
 	 * SETUP CPC0_CR0
 	 *******************************************************************/
 	LI32(r4, 0x007000c0)
-	mtdcr	cntrl0, r4
+	mtdcr	CPC0_CR0, r4
 
 	/********************************************************************
 	 * Setup CPC0_CR1: Change PCIINT signal to PerWE
 	 *******************************************************************/
-	mfdcr	r4, cntrl1
+	mfdcr	r4, CPC0_CR1
 	ori	r4, r4, 0x4000
-	mtdcr	cntrl1, r4
+	mtdcr	CPC0_CR1, r4
 
 	/********************************************************************
 	 * Setup External Bus Controller (EBC).
 	 *******************************************************************/
-	WDCR_EBC(epcr, 0xd84c0000)
+	WDCR_EBC(EBC0_CFG, 0xd84c0000)
 	/********************************************************************
 	 * Memory Bank 0 (Intel 28F128J3 Flash) initialization
 	 *******************************************************************/
-	/*WDCR_EBC(pb0ap, 0x02869200)*/
+	/*WDCR_EBC(PB1AP, 0x02869200)*/
-	WDCR_EBC(pb0ap, 0x07869200)
+	WDCR_EBC(PB1AP, 0x07869200)
-	WDCR_EBC(pb0cr, 0xfe0bc000)
+	WDCR_EBC(PB0CR, 0xfe0bc000)
 	/********************************************************************
 	 * Memory Bank 1 (Holtek HT6542B PS/2) initialization
 	 *******************************************************************/
-	WDCR_EBC(pb1ap, 0x1f869200)
+	WDCR_EBC(PB1AP, 0x1f869200)
-	WDCR_EBC(pb1cr, 0xf0818000)
+	WDCR_EBC(PB1CR, 0xf0818000)
 	/********************************************************************
 	 * Memory Bank 2 (Epson S1D13506) initialization
 	 *******************************************************************/
-	WDCR_EBC(pb2ap, 0x05860300)
+	WDCR_EBC(PB2AP, 0x05860300)
-	WDCR_EBC(pb2cr, 0xf045a000)
+	WDCR_EBC(PB2CR, 0xf045a000)
 	/********************************************************************
 	 * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
 	 *******************************************************************/
-	WDCR_EBC(pb3ap, 0x0387d200)
+	WDCR_EBC(PB3AP, 0x0387d200)
-	WDCR_EBC(pb3cr, 0xf021c000)
+	WDCR_EBC(PB3CR, 0xf021c000)
 	/********************************************************************
 	 * Memory Bank 4-7 (Unused) initialization
 	 *******************************************************************/
-	WDCR_EBC(pb4ap, 0)
+	WDCR_EBC(PB4AP, 0)
-	WDCR_EBC(pb4cr, 0)
+	WDCR_EBC(PB4CR, 0)
-	WDCR_EBC(pb5ap, 0)
+	WDCR_EBC(PB5AP, 0)
-	WDCR_EBC(pb5cr, 0)
+	WDCR_EBC(PB5CR, 0)
-	WDCR_EBC(pb6ap, 0)
+	WDCR_EBC(PB6AP, 0)
-	WDCR_EBC(pb6cr, 0)
+	WDCR_EBC(PB6CR, 0)
-	WDCR_EBC(pb7ap, 0)
+	WDCR_EBC(PB7AP, 0)
-	WDCR_EBC(pb7cr, 0)
+	WDCR_EBC(PB7CR, 0)
 
 	/* We are all done */
 	mtlr	r0			/* Restore link register */

board/csb472/csb472.c

@@ -63,7 +63,7 @@ int board_early_init_f(void)
 	mtdcr (uicvcr, 0x00000001);  /* set vect base=0,INT0 highest priority */
 	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
 
-	mtebc (epcr, 0xa8400000);   /* EBC always driven */
+	mtebc (EBC0_CFG, 0xa8400000);   /* EBC always driven */
 
 	return 0; /* success */
 }
@@ -103,29 +103,29 @@ phys_size_t initdram (int board_type)
 
 	tot_size = 0;
 
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;

board/csb472/init.S

@@ -38,17 +38,17 @@
 
 #define WDCR_EBC(reg,val) \
 	addi    r4,0,reg;\
-	mtdcr   ebccfga,r4;\
+	mtdcr   EBC0_CFGADDR,r4;\
 	addis   r4,0,val@h;\
 	ori     r4,r4,val@l;\
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 #define WDCR_SDRAM(reg,val) \
 	addi    r4,0,reg;\
-	mtdcr   memcfga,r4;\
+	mtdcr   SDRAM0_CFGADDR,r4;\
 	addis   r4,0,val@h;\
 	ori     r4,r4,val@l;\
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 /******************************************************************************
  * Function:	ext_bus_cntlr_init
@@ -106,47 +106,47 @@ ext_bus_cntlr_init:
 	 * SETUP CPC0_CR0
 	 *******************************************************************/
 	LI32(r4, 0x00c01030)
-	mtdcr	cntrl0, r4
+	mtdcr	CPC0_CR0, r4
 
 	/********************************************************************
 	 * Setup CPC0_CR1: Change PCIINT signal to PerWE
 	 *******************************************************************/
-	mfdcr	r4, cntrl1
+	mfdcr	r4, CPC0_CR1
 	ori	r4, r4, 0x4000
-	mtdcr	cntrl1, r4
+	mtdcr	CPC0_CR1, r4
 
 	/********************************************************************
 	 * Setup External Bus Controller (EBC).
 	 *******************************************************************/
-	WDCR_EBC(epcr, 0xd84c0000)
+	WDCR_EBC(EBC0_CFG, 0xd84c0000)
 	/********************************************************************
 	 * Memory Bank 0 (Intel 28F640J3 Flash) initialization
 	 *******************************************************************/
-	/*WDCR_EBC(pb0ap, 0x03055200)*/
+	/*WDCR_EBC(PB1AP, 0x03055200)*/
-	/*WDCR_EBC(pb0ap, 0x04055200)*/
+	/*WDCR_EBC(PB1AP, 0x04055200)*/
-	WDCR_EBC(pb0ap, 0x08055200)
+	WDCR_EBC(PB1AP, 0x08055200)
-	WDCR_EBC(pb0cr, 0xff87a000)
+	WDCR_EBC(PB0CR, 0xff87a000)
 	/********************************************************************
 	 * Memory Bank 3 (Xilinx XC95144 CPLD) initialization
 	 *******************************************************************/
-	/*WDCR_EBC(pb3ap, 0x07869200)*/
+	/*WDCR_EBC(PB3AP, 0x07869200)*/
-	WDCR_EBC(pb3ap, 0x04055200)
+	WDCR_EBC(PB3AP, 0x04055200)
-	WDCR_EBC(pb3cr, 0xf081c000)
+	WDCR_EBC(PB3CR, 0xf081c000)
 	/********************************************************************
 	 * Memory Bank 1,2,4-7 (Unused) initialization
 	 *******************************************************************/
-	WDCR_EBC(pb1ap, 0)
+	WDCR_EBC(PB1AP, 0)
-	WDCR_EBC(pb1cr, 0)
+	WDCR_EBC(PB1CR, 0)
-	WDCR_EBC(pb2ap, 0)
+	WDCR_EBC(PB2AP, 0)
-	WDCR_EBC(pb2cr, 0)
+	WDCR_EBC(PB2CR, 0)
-	WDCR_EBC(pb4ap, 0)
+	WDCR_EBC(PB4AP, 0)
-	WDCR_EBC(pb4cr, 0)
+	WDCR_EBC(PB4CR, 0)
-	WDCR_EBC(pb5ap, 0)
+	WDCR_EBC(PB5AP, 0)
-	WDCR_EBC(pb5cr, 0)
+	WDCR_EBC(PB5CR, 0)
-	WDCR_EBC(pb6ap, 0)
+	WDCR_EBC(PB6AP, 0)
-	WDCR_EBC(pb6cr, 0)
+	WDCR_EBC(PB6CR, 0)
-	WDCR_EBC(pb7ap, 0)
+	WDCR_EBC(PB7AP, 0)
-	WDCR_EBC(pb7cr, 0)
+	WDCR_EBC(PB7CR, 0)
 
 	/* We are all done */
 	mtlr	r0			/* Restore link register */

board/dave/PPChameleonEVB/PPChameleonEVB.c

@@ -65,9 +65,9 @@ int board_early_init_f (void)
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
 #if 1 /* test-only */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 #else
-	mtebc (epcr, 0x28400000); /* ebc in high-z */
+	mtebc (EBC0_CFG, 0x28400000); /* ebc in high-z */
 #endif
 	return 0;
 }
@@ -101,7 +101,7 @@ int misc_init_r (void)
 	int status;
 	int index;
 	int i;
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
 	if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {

board/dave/PPChameleonEVB/flash.c

@@ -75,9 +75,9 @@ unsigned long flash_init (void)
 	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base = -size;
 	switch (size) {
 	case 1 << 20:
@@ -97,7 +97,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
 
 	/* Monitor protection ON by default */

board/eric/eric.c

@@ -70,7 +70,7 @@ int board_early_init_f (void)
 	mtdcr (uicvcr, 0x00000001);	/* set vect base=0,INT0 highest priority */
 	mtdcr (uicsr, 0xFFFFFFFF);	/* clear all ints */
 
-	mtdcr (cntrl0, 0x00002000);	/* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
+	mtdcr (CPC0_CR0, 0x00002000);	/* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
 
 	out32 (PPC405GP_GPIO0_OR, 0x60000000);	/*fixme is SMB_INT high or low active??; IRQ6 is GPIO23 output */
 	out32 (PPC405GP_GPIO0_TCR, 0x7E400000);

board/eric/flash.c

@@ -105,24 +105,24 @@ unsigned long flash_init (void)
 
 	    if (size_b1)
 	      {
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
-		pbcr = mfdcr(ebccfgd);
+		pbcr = mfdcr(EBC0_CFGDATA);
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
 		base_b1 = -size_b1;
 		pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
+		mtdcr(EBC0_CFGDATA, pbcr);
-		/*          printf("pb1cr = %x\n", pbcr); */
+		/*          printf("PB1CR = %x\n", pbcr); */
 	      }
 
 	    if (size_b0)
 	      {
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
-		pbcr = mfdcr(ebccfgd);
+		pbcr = mfdcr(EBC0_CFGDATA);
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
 		base_b0 = base_b1 - size_b0;
 		pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
+		mtdcr(EBC0_CFGDATA, pbcr);
-		/*            printf("pb0cr = %x\n", pbcr); */
+		/*            printf("PB0CR = %x\n", pbcr); */
 	      }
 
 	    size_b0 = flash_get_size((volatile FLASH_WORD_SIZE *)base_b0, &flash_info[0]);

board/eric/init.S

@@ -76,129 +76,129 @@ ext_bus_cntlr_init:
 	/* Memory Bank 0 (Flash) initialization (from openbios) */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS0_AP@h
 	ori     r4,r4,CS0_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS0_CR@h
 	ori     r4,r4,CS0_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 1 (NVRAM/RTC) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb1ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS1_AP@h
 	ori     r4,r4,CS1_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb1cr
+	addi    r4,0,PB1CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS1_CR@h
 	ori     r4,r4,CS1_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 2 (A/D converter) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb2ap
+	addi    r4,0,PB2AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS2_AP@h
 	ori     r4,r4,CS2_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb2cr
+	addi    r4,0,PB2CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS2_CR@h
 	ori     r4,r4,CS2_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 3 (Ethernet PHY Reset) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb3ap
+	addi    r4,0,PB3AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS3_AP@h
 	ori     r4,r4,CS3_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb3cr
+	addi    r4,0,PB3CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS3_CR@h
 	ori     r4,r4,CS3_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 4 (PC-MIP PRSNT1#) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb4ap
+	addi    r4,0,PB4AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS4_AP@h
 	ori     r4,r4,CS4_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb4cr
+	addi    r4,0,PB4CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS4_CR@h
 	ori     r4,r4,CS4_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 5 (PC-MIP PRSNT2#) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb5ap
+	addi    r4,0,PB5AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS5_AP@h
 	ori     r4,r4,CS5_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb5cr
+	addi    r4,0,PB5CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS5_CR@h
 	ori     r4,r4,CS5_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 6 (CPU LED0) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb6ap
+	addi    r4,0,PB6AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS6_AP@h
 	ori     r4,r4,CS6_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb6cr
+	addi    r4,0,PB6CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS6_CR@h
 	ori     r4,r4,CS5_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	/*----------------------------------------------------------------------- */
 	/* Memory Bank 7 (CPU LED1) initialization */
 	/*----------------------------------------------------------------------- */
 
-	addi    r4,0,pb7ap
+	addi    r4,0,PB7AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS7_AP@h
 	ori     r4,r4,CS7_AP@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb7cr
+	addi    r4,0,PB7CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,CS7_CR@h
 	ori     r4,r4,CS7_CR@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 /*	addis   r4,r0,FPGA_BRDC@h */
 /*	ori     r4,r4,FPGA_BRDC@l */
@@ -229,40 +229,40 @@ sdram_init:
 	/*------------------------------------------------------------------- */
 
 	addi    r4,0,mem_mb0cf
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,MB0CF@h
 	ori     r4,r4,MB0CF@l
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*------------------------------------------------------------------- */
 	/* Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2) */
 	/*------------------------------------------------------------------- */
 
 	addi    r4,0,mem_mb1cf
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,MB1CF@h
 	ori     r4,r4,MB1CF@l
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*------------------------------------------------------------------- */
 	/* Set MB2CF for bank 2. off */
 	/*------------------------------------------------------------------- */
 
 	addi    r4,0,mem_mb2cf
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,MB2CF@h
 	ori     r4,r4,MB2CF@l
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*------------------------------------------------------------------- */
 	/* Set MB3CF for bank 3. off */
 	/*------------------------------------------------------------------- */
 
 	addi    r4,0,mem_mb3cf
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,MB3CF@h
 	ori     r4,r4,MB3CF@l
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*------------------------------------------------------------------- */
 	/* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. */
@@ -276,7 +276,7 @@ sdram_init:
 	/* maybe 133Mhz. */
 	/*------------------------------------------------------------------- */
 
-	mfdcr   r5,strap                 /* determine FBK divider */
+	mfdcr   r5,CPC0_PSR               /* determine FBK divider */
 					  /* via STRAP reg to calc PLB speed. */
 					  /* SDRAM speed is the same as the PLB */
 					  /* speed. */
@@ -306,15 +306,15 @@ sdram_init:
 	/* Set SDTR1 */
 	/*------------------------------------------------------------------- */
 	addi    r4,0,mem_sdtr1
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
-	mtdcr   memcfgd,r6
+	mtdcr   SDRAM0_CFGDATA,r6
 
 	/*------------------------------------------------------------------- */
 	/* Set RTR */
 	/*------------------------------------------------------------------- */
 	addi    r4,0,mem_rtr
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
-	mtdcr   memcfgd,r7
+	mtdcr   SDRAM0_CFGDATA,r7
 
 	/*------------------------------------------------------------------- */
 	/* Delay to ensure 200usec have elapsed since reset. Assume worst */
@@ -333,10 +333,10 @@ sdram_init:
 	/* read/prefetch. */
 	/*------------------------------------------------------------------- */
 	addi    r4,0,mem_mcopt1
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,0x8080             /* set DC_EN=1 */
 	ori     r4,r4,0x0000
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*------------------------------------------------------------------- */
 	/* Delay to ensure 10msec have elapsed since reset. This is */

board/esd/apc405/apc405.c

@@ -92,7 +92,7 @@ int N_AU_IMAGES = (sizeof(au_image) / sizeof(au_image[0]));
 
 int board_revision(void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	unsigned long value;
 
 	/*
@@ -100,8 +100,8 @@ int board_revision(void)
 	 */
 
 	/* Setup GPIO pins (CS2/GPIO11, CS3/GPIO12 and CS4/GPIO13 as GPIO) */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x03800000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03800000);
 	out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x001c0000);
 	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x001c0000);
 
@@ -113,7 +113,7 @@ int board_revision(void)
 	/*
 	 * Restore GPIO settings
 	 */
-	mtdcr(cntrl0, cntrl0Reg);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 	switch (value) {
 	case 0x001c0000:
@@ -166,7 +166,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks
 	 */
-	mtebc(epcr, 0xa8400000); /* ebc always driven */
+	mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	/*
 	 * New boards have a single 32MB flash connected to CS0
@@ -174,12 +174,12 @@ int board_early_init_f (void)
 	 */
 	if (board_revision() >= 8) {
 		/* disable CS1 */
-		mtebc(pb1ap, 0);
+		mtebc(PB1AP, 0);
-		mtebc(pb1cr, 0);
+		mtebc(PB1CR, 0);
 
 		/* resize CS0 to 32MB */
-		mtebc(pb0ap, CONFIG_SYS_EBC_PB0AP_HWREV8);
+		mtebc(PB0AP, CONFIG_SYS_EBC_PB0AP_HWREV8);
-		mtebc(pb0cr, CONFIG_SYS_EBC_PB0CR_HWREV8);
+		mtebc(PB0CR, CONFIG_SYS_EBC_PB0CR_HWREV8);
 	}
 
 	return 0;
@@ -209,7 +209,7 @@ int misc_init_r(void)
 	int status;
 	int index;
 	int i;
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	char *str;
 	uchar *logo_addr;
 	ulong logo_size;
@@ -219,8 +219,8 @@ int misc_init_r(void)
 	/*
 	 * Setup GPIO pins (CS6+CS7 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
 
 	dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
 	if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
@@ -265,7 +265,7 @@ int misc_init_r(void)
 	}
 
 	/* restore gpio/cs settings */
-	mtdcr(cntrl0, cntrl0Reg);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 	puts("FPGA:  ");
 

board/esd/ar405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/ash405/ash405.c

@@ -77,7 +77,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/esd/ash405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/canbt/canbt.c

@@ -52,16 +52,16 @@ const unsigned char fpgadata[] = {
 
 int board_early_init_f (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	int index, len, i;
 	int status;
 
 	/*
 	 * Setup GPIO pins
 	 */
-	cntrl0Reg = mfdcr (cntrl0) & 0xf0001fff;
+	CPC0_CR0Reg = mfdcr (CPC0_CR0) & 0xf0001fff;
-	cntrl0Reg |= 0x0070f000;
+	CPC0_CR0Reg |= 0x0070f000;
-	mtdcr (cntrl0, cntrl0Reg);
+	mtdcr (CPC0_CR0, CPC0_CR0Reg);
 
 #ifdef FPGA_DEBUG
 	/* set up serial port with default baudrate */

board/esd/canbt/flash.c

@@ -64,13 +64,13 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
-	/*          printf("pb1cr = %x\n", pbcr); */
+	/*          printf("PB1CR = %x\n", pbcr); */
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/cms700/cms700.c

@@ -56,7 +56,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	/*
 	 * Reset CPLD via GPIO12 (CS3) pin

board/esd/cms700/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/cpci2dp/cpci2dp.c

@@ -31,13 +31,13 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int board_early_init_f (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/*
 	 * Setup GPIO pins
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg |
+	mtdcr(CPC0_CR0, CPC0_CR0Reg |
 	      ((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED |
 		CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
 
@@ -72,7 +72,7 @@ int board_early_init_f (void)
 
 int misc_init_r (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -81,8 +81,8 @@ int misc_init_r (void)
 	/*
 	 * Select cts (and not dsr) on uart1
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
 
 	return (0);
 }

board/esd/cpci2dp/flash.c

@@ -64,13 +64,13 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
-	/*          printf("pb1cr = %x\n", pbcr); */
+	/*          printf("PB1CR = %x\n", pbcr); */
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/cpci405/cpci405.c

@@ -214,7 +214,7 @@ int ctermm2(void)
 
 int cpci405_host(void)
 {
-	if (mfdcr(strap) & PSR_PCI_ARBIT_EN)
+	if (mfdcr(CPC0_PSR) & PSR_PCI_ARBIT_EN)
 		return -1;		/* yes, board is cpci405 host */
 	else
 		return 0;		/* no, board is cpci405 adapter */
@@ -222,14 +222,14 @@ int cpci405_host(void)
 
 int cpci405_version(void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	unsigned long value;
 
 	/*
 	 * Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
 	out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00180000);
 	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00180000);
 	udelay(1000); /* wait some time before reading input */
@@ -238,7 +238,7 @@ int cpci405_version(void)
 	/*
 	 * Restore GPIO settings
 	 */
-	mtdcr(cntrl0, cntrl0Reg);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 	switch (value) {
 	case 0x00180000:
@@ -261,7 +261,7 @@ int cpci405_version(void)
 
 int misc_init_r (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -283,8 +283,8 @@ int misc_init_r (void)
 		/*
 		 * Setup GPIO pins (CS6+CS7 as GPIO)
 		 */
-		cntrl0Reg = mfdcr(cntrl0);
+		CPC0_CR0Reg = mfdcr(CPC0_CR0);
-		mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+		mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
 
 		dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
 		if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE,
@@ -330,7 +330,7 @@ int misc_init_r (void)
 		}
 
 		/* restore gpio/cs settings */
-		mtdcr(cntrl0, cntrl0Reg);
+		mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 		puts("FPGA:  ");
 
@@ -400,8 +400,8 @@ int misc_init_r (void)
 	/*
 	 * Select cts (and not dsr) on uart1
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
 
 	return 0;
 }

board/esd/cpci405/flash.c

@@ -91,13 +91,13 @@ unsigned long flash_init (void)
 			size_b1 = 1 << 20;
 		}
 		base_b1 = -size_b1;
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
 		pbcr = (pbcr & 0x0001ffff) | base_b1 | (calc_size(size_b1) << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
 #if 0 /* test-only */
-		printf("size_b1=%x base_b1=%x pb1cr = %x\n",
+		printf("size_b1=%x base_b1=%x PB1CR = %x\n",
 		       size_b1, base_b1, pbcr); /* test-only */
 #endif
 	}
@@ -108,13 +108,13 @@ unsigned long flash_init (void)
 			size_b0 = 1 << 20;
 		}
 		base_b0 = base_b1 - size_b0;
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
 		pbcr = (pbcr & 0x0001ffff) | base_b0 | (calc_size(size_b0) << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
 #if 0 /* test-only */
-		printf("size_b0=%x base_b0=%x pb0cr = %x\n",
+		printf("size_b0=%x base_b0=%x PB0CR = %x\n",
 		       size_b0, base_b0, pbcr); /* test-only */
 #endif
 	}

board/esd/cpciiser4/flash.c

@@ -64,13 +64,13 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
-	/*          printf("pb1cr = %x\n", pbcr); */
+	/*          printf("PB1CR = %x\n", pbcr); */
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/dp405/dp405.c

@@ -54,7 +54,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	/*
 	 * Reset CPLD via GPIO13 (CS4) pin

board/esd/dp405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/du405/du405.c

@@ -135,7 +135,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 100 us
 	 */
-	mtebc (epcr, 0xb8400000);
+	mtebc (EBC0_CFG, 0xb8400000);
 
 	return 0;
 }
@@ -143,13 +143,13 @@ int board_early_init_f (void)
 
 int misc_init_r (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/*
 	 * Setup UART1 handshaking: use CTS instead of DSR
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
 
 	return (0);
 }

board/esd/du405/flash.c

@@ -67,25 +67,25 @@ unsigned long flash_init (void)
 	/* Re-do sizing to get full correct info */
 
 	if (size_b1) {
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
 		base_b1 = -size_b1;
 		pbcr = (pbcr & 0x0001ffff) | base_b1 |
 				(((size_b1 / 1024 / 1024) - 1) << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
-		/*          printf("pb1cr = %x\n", pbcr); */
+		/*          printf("PB1CR = %x\n", pbcr); */
 	}
 
 	if (size_b0) {
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
 		base_b0 = base_b1 - size_b0;
 		pbcr = (pbcr & 0x0001ffff) | base_b0 |
 				(((size_b0 / 1024 / 1024) - 1) << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
-		/*            printf("pb0cr = %x\n", pbcr); */
+		/*            printf("PB0CR = %x\n", pbcr); */
 	}
 
 	size_b0 = flash_get_size ((vu_long *) base_b0, &flash_info[0]);

board/esd/du440/du440.c

@@ -45,8 +45,8 @@ int board_early_init_f(void)
 	u32 sdr0_pfc1, sdr0_pfc2;
 	u32 reg;
 
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, 0xb8400000);
+	mtdcr(EBC0_CFGDATA, 0xb8400000);
 
 	/*
 	 * Setup the GPIO pins
@@ -145,8 +145,8 @@ int board_early_init_f(void)
 	mtsdr(SDR0_PFC1, sdr0_pfc1);
 
 	/* PCI arbiter enabled */
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);
 
 	/* setup NAND FLASH */
 	mfsdr(SDR0_CUST0, sdr0_cust0);
@@ -176,12 +176,12 @@ int misc_init_r(void)
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
 	gd->bd->bi_flashoffset = 0;
 
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	size_val = ffs(gd->bd->bi_flashsize) - 21;
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/*
 	 * Re-check to get correct base address
@@ -265,8 +265,8 @@ int misc_init_r(void)
 	 * This fix will make the MAL burst disabling patch for the Linux
 	 * EMAC driver obsolete.
 	 */
-	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
-	mtdcr(plb4_acr, reg);
+	mtdcr(PLB4_ACR, reg);
 
 	/*
 	 * release IO-RST#
@@ -380,35 +380,35 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*
 	 * Set Nebula PLB4 arbiter to fair mode.
 	 */
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	return 1;
 }

board/esd/hh405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/hh405/hh405.c

@@ -374,7 +374,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc(epcr, 0xa8400000); /* ebc always driven */
+	mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/esd/hub405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/hub405/hub405.c

@@ -97,7 +97,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/esd/ocrtc/flash.c

@@ -68,9 +68,9 @@ unsigned long flash_init (void)
 	/* Re-do sizing to get full correct info */
 
 	if (size_b1) {
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
 		base_b1 = -size_b1;
 		switch (size_b1) {
 		case 1 << 20:
@@ -90,14 +90,14 @@ unsigned long flash_init (void)
 			break;
 		}
 		pbcr = (pbcr & 0x0001ffff) | base_b1 | (size_val << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
-		/*          printf("pb1cr = %x\n", pbcr); */
+		/*          printf("PB1CR = %x\n", pbcr); */
 	}
 
 	if (size_b0) {
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		pbcr = mfdcr (ebccfgd);
+		pbcr = mfdcr (EBC0_CFGDATA);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
 		base_b0 = base_b1 - size_b0;
 		switch (size_b1) {
 		case 1 << 20:
@@ -117,8 +117,8 @@ unsigned long flash_init (void)
 			break;
 		}
 		pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-		mtdcr (ebccfgd, pbcr);
+		mtdcr (EBC0_CFGDATA, pbcr);
-		/*            printf("pb0cr = %x\n", pbcr); */
+		/*            printf("PB0CR = %x\n", pbcr); */
 	}
 
 	size_b0 = flash_get_size ((vu_long *) base_b0, &flash_info[0]);

board/esd/ocrtc/ocrtc.c

@@ -57,7 +57,7 @@ int board_early_init_f (void)
 	 * EBC Configuration Register: clear EBTC -> high-Z ebc signals between
 	 * transfers, set device-paced timeout to 256 cycles
 	 */
-	mtebc (epcr, 0x20400000);
+	mtebc (EBC0_CFG, 0x20400000);
 
 	return 0;
 }

board/esd/pci405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/pci405/pci405.c

@@ -67,7 +67,7 @@ const unsigned char fpgadata[] =
 
 int board_revision(void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 	unsigned long value;
 
 	/*
@@ -77,8 +77,8 @@ int board_revision(void)
 	/*
 	 * Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
 	out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00100200);
 	out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00100200);
 	udelay(1000);                   /* wait some time before reading input */
@@ -87,7 +87,7 @@ int board_revision(void)
 	/*
 	 * Restore GPIO settings
 	 */
-	mtdcr(cntrl0, cntrl0Reg);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg);
 
 	switch (value) {
 	case 0x00100200:
@@ -133,7 +133,7 @@ unsigned long fpga_init_state(void)
 
 int board_early_init_f (void)
 {
-	unsigned long cntrl0Reg;
+	unsigned long CPC0_CR0Reg;
 
 	/*
 	 * First pull fpga-prg pin low, to disable fpga logic (on version 1.2 board)
@@ -166,18 +166,18 @@ int board_early_init_f (void)
 	/*
 	 * Setup GPIO pins (IRQ4/GPIO21 as GPIO)
 	 */
-	cntrl0Reg = mfdcr(cntrl0);
+	CPC0_CR0Reg = mfdcr(CPC0_CR0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00008000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00008000);
 
 	/*
 	 * Setup GPIO pins (CS6+CS7 as GPIO)
 	 */
-	mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+	mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
 
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }
@@ -282,11 +282,11 @@ int misc_init_r (void)
 #define PCI0_BRDGOPT1 0x4a
 	pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
 
-#define plb0_acr      0x87
+#define PLB0_ACR      0x87
 	/*
 	 * Enable fairness and high bus utilization
 	 */
-	mtdcr(plb0_acr, 0x98000000);
+	mtdcr(PLB0_ACR, 0x98000000);
 
 	free(dst);
 	return (0);
@@ -313,14 +313,14 @@ int checkboard (void)
 	printf(" (Rev 1.%ld", gd->board_type);
 
 	if (gd->board_type >= 2) {
-		unsigned long cntrl0Reg;
+		unsigned long CPC0_CR0Reg;
 		unsigned long value;
 
 		/*
 		 * Setup GPIO pins (Trace/GPIO1 to GPIO)
 		 */
-		cntrl0Reg = mfdcr(cntrl0);
+		CPC0_CR0Reg = mfdcr(CPC0_CR0);
-		mtdcr(cntrl0, cntrl0Reg & ~0x08000000);
+		mtdcr(CPC0_CR0, CPC0_CR0Reg & ~0x08000000);
 		out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x40000000);
 		out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x40000000);
 		udelay(1000);                   /* wait some time before reading input */

board/esd/plu405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/plu405/plu405.c

@@ -90,7 +90,7 @@ int board_early_init_f(void)
 	 * EBC Configuration Register: set ready timeout to
 	 * 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc(epcr, 0xa8400000); /* ebc always driven */
+	mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/esd/pmc405/pmc405.c

@@ -60,12 +60,12 @@ int board_early_init_f (void)
 	 * EBC Configuration Register:
 	 * set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000);
+	mtebc (EBC0_CFG, 0xa8400000);
 
 	/*
 	 * Setup GPIO pins
 	 */
-	mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_FPGA_INIT |
+	mtdcr(CPC0_CR0, mfdcr(CPC0_CR0) | ((CONFIG_SYS_FPGA_INIT |
 					CONFIG_SYS_FPGA_DONE |
 					CONFIG_SYS_XEREADY |
 					CONFIG_SYS_NONMONARCH |
@@ -73,7 +73,7 @@ int board_early_init_f (void)
 
 	if (!(in_be32((void *)GPIO0_IR) & CONFIG_SYS_REV1_2)) {
 		/* rev 1.2 boards */
-		mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_INTA_FAKE |
+		mtdcr(CPC0_CR0, mfdcr(CPC0_CR0) | ((CONFIG_SYS_INTA_FAKE |
 						CONFIG_SYS_SELF_RST) << 5));
 	}
 

board/esd/pmc405de/pmc405de.c

@@ -127,7 +127,7 @@ int board_early_init_f(void)
 	 * - set ready timeout to 512 ebc-clks -> ca. 15 us
 	 * - EBC lines are always driven
 	 */
-	mtebc(epcr, 0xa8400000);
+	mtebc(EBC0_CFG, 0xa8400000);
 
 	return 0;
 }

board/esd/pmc440/pmc440.c

@@ -64,7 +64,7 @@ struct serial_device *default_serial_console(void)
 	 * Use default console on P4 when strapping jumper
 	 * is installed (bootstrap option != 'H').
 	 */
-	mfsdr(SDR_PINSTP, val);
+	mfsdr(SDR0_PINSTP, val);
 	if (((val & 0xf0000000) >> 29) != 7)
 		return &serial1_device;
 
@@ -100,8 +100,8 @@ int board_early_init_f(void)
 	u32 reg;
 
 	/* general EBC configuration (disable EBC timeouts) */
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, 0xf8400000);
+	mtdcr(EBC0_CFGDATA, 0xf8400000);
 
 	/*
 	 * Setup the GPIO pins
@@ -134,13 +134,13 @@ int board_early_init_f(void)
 	out_be32((void *)GPIO1_ISR3H, 0x00000000);
 
 	/* patch PLB:PCI divider for 66MHz PCI */
-	mfcpr(clk_spcid, reg);
+	mfcpr(CPR0_SPCID, reg);
 	if (pci_is_66mhz() && (reg != 0x02000000)) {
-		mtcpr(clk_spcid, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
+		mtcpr(CPR0_SPCID, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
 
-		mfcpr(clk_icfg, reg);
+		mfcpr(CPR0_ICFG, reg);
 		reg |= CPR0_ICFG_RLI_MASK;
-		mtcpr(clk_icfg, reg);
+		mtcpr(CPR0_ICFG, reg);
 
 		mtspr(SPRN_DBCR0, 0x20000000); /* do chip reset */
 	}
@@ -240,19 +240,19 @@ int misc_init_r(void)
 	gd->bd->bi_flashoffset = 0;
 
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtdcr(ebccfga, pb2cr);
+	mtdcr(EBC0_CFGADDR, PB2CR);
 #else
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 #endif
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	size_val = ffs(gd->bd->bi_flashsize) - 21;
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
 #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-	mtdcr(ebccfga, pb2cr);
+	mtdcr(EBC0_CFGADDR, PB2CR);
 #else
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 #endif
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/*
 	 * Re-check to get correct base address
@@ -424,8 +424,8 @@ int misc_init_r(void)
 	 * This fix will make the MAL burst disabling patch for the Linux
 	 * EMAC driver obsolete.
 	 */
-	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
-	mtdcr(plb4_acr, reg);
+	mtdcr(PLB4_ACR, reg);
 
 #ifdef CONFIG_FPGA
 	pmc440_init_fpga();
@@ -507,35 +507,35 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*
 	 * Set Nebula PLB4 arbiter to fair mode.
 	 */
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 #ifdef CONFIG_PCI_PNP
 	hose->fixup_irq = pmc440_pci_fixup_irq;

board/esd/voh405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/voh405/voh405.c

@@ -99,7 +99,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/esd/vom405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/vom405/vom405.c

@@ -56,7 +56,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	/*
 	 * Reset CPLD via GPIO12 (CS3) pin

board/esd/wuh405/flash.c

@@ -65,9 +65,9 @@ unsigned long flash_init (void)
 	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
 	base_b0 = -size_b0;
 	switch (size_b0) {
 	case 1 << 20:
@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,

board/esd/wuh405/wuh405.c

@@ -75,7 +75,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 
 	return 0;
 }

board/exbitgen/exbitgen.c

@@ -94,29 +94,29 @@ phys_size_t initdram (int board_type)
 
 	tot_size = 0;
 
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;
 	}
 
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 	if (tmp & 0x00000001) {
 		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
 		tot_size += bank_size;

board/exbitgen/init.S

@@ -109,10 +109,10 @@
 
 
 #define WDCR_EBC(reg,val) addi    r4,0,reg;\
-	mtdcr   ebccfga,r4;\
+	mtdcr   EBC0_CFGADDR,r4;\
 	addis   r4,0,val@h;\
 	ori     r4,r4,val@l;\
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 /*---------------------------------------------------------------------
  * Function:     ext_bus_cntlr_init
@@ -164,22 +164,22 @@ ext_bus_cntlr_init:
 	 * Memory Bank 0 (Boot Flash) initialization
 	 *---------------------------------------------------------------
 	 */
-	WDCR_EBC(pb0ap, FLASH_32bit_AP)
+	WDCR_EBC(PB1AP, FLASH_32bit_AP)
-	WDCR_EBC(pb0cr, 0xffe38000)
+	WDCR_EBC(PB0CR, 0xffe38000)
-/*pnc	WDCR_EBC(pb0cr, FLASH_32bit_CR) */
+/*pnc	WDCR_EBC(PB0CR, FLASH_32bit_CR) */
 
 	/*---------------------------------------------------------------
 	 * Memory Bank 5 (CPLD) initialization
 	 *---------------------------------------------------------------
 	 */
-	WDCR_EBC(pb5ap, 0x01010040)
+	WDCR_EBC(PB5AP, 0x01010040)
-/*jsa recommendation:		WDCR_EBC(pb5ap, 0x00010040) */
+/*jsa recommendation:		WDCR_EBC(PB5AP, 0x00010040) */
-	WDCR_EBC(pb5cr, 0x10038000)
+	WDCR_EBC(PB5CR, 0x10038000)
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 6 (not used) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb6cr, 0x00000000)
+	WDCR_EBC(PB6CR, 0x00000000)
 
 	/* Read HW ID to determine whether old H2 board or new generic CPU board */
 	addis	r3, 0,  HW_ID_ADDR@h
@@ -196,24 +196,24 @@ setup_genieboard:
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 1 (Application Flash) initialization for generic CPU board */
 	/*--------------------------------------------------------------- */
-/*	WDCR_EBC(pb1ap, 0x7b015480)	/###* T.B.M. */
+/*	WDCR_EBC(PB1AP, 0x7b015480)	/###* T.B.M. */
-/*	WDCR_EBC(pb1ap, 0x7F8FFE80)	/###* T.B.M. */
+/*	WDCR_EBC(PB1AP, 0x7F8FFE80)	/###* T.B.M. */
-	WDCR_EBC(pb1ap, 0x9b015480)	/* hlb-20020207: burst 8 bit 6 cycles  */
+	WDCR_EBC(PB1AP, 0x9b015480)	/* hlb-20020207: burst 8 bit 6 cycles  */
 
-/*	WDCR_EBC(pb1cr, 0x20098000)	/###* 16 MB */
+/*	WDCR_EBC(PB1CR, 0x20098000)	/###* 16 MB */
-	WDCR_EBC(pb1cr, 0x200B8000)	/* 32 MB */
+	WDCR_EBC(PB1CR, 0x200B8000)	/* 32 MB */
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 4 (Onboard FPGA) initialization for generic CPU board */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb4ap, 0x01010000)	/*  */
+	WDCR_EBC(PB4AP, 0x01010000)	/*  */
-	WDCR_EBC(pb4cr, 0x1021c000)	/*  */
+	WDCR_EBC(PB4CR, 0x1021c000)	/*  */
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 7 (Heathrow chip on Reference board) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb7ap, 0x200ffe80)	/* No Ready, many wait states (let reflections die out) */
+	WDCR_EBC(PB7AP, 0x200ffe80)	/* No Ready, many wait states (let reflections die out) */
-	WDCR_EBC(pb7cr, 0X4001A000)
+	WDCR_EBC(PB7CR, 0X4001A000)
 
 	bl	setup_continue
 
@@ -222,36 +222,36 @@ setup_h2evalboard:
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 1 (Application Flash) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb1ap, 0x7b015480)	/* T.B.M. */
+	WDCR_EBC(PB1AP, 0x7b015480)	/* T.B.M. */
-/*3010	WDCR_EBC(pb1ap, 0x7F8FFE80)	/###* T.B.M. */
+/*3010	WDCR_EBC(PB1AP, 0x7F8FFE80)	/###* T.B.M. */
-	WDCR_EBC(pb1cr, 0x20058000)
+	WDCR_EBC(PB1CR, 0x20058000)
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 2 (Application Flash) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb2ap, 0x7b015480)	/* T.B.M. */
+	WDCR_EBC(PB2AP, 0x7b015480)	/* T.B.M. */
-/*3010	WDCR_EBC(pb2ap, 0x7F8FFE80)	/###* T.B.M. */
+/*3010	WDCR_EBC(PB2AP, 0x7F8FFE80)	/###* T.B.M. */
-	WDCR_EBC(pb2cr, 0x20458000)
+	WDCR_EBC(PB2CR, 0x20458000)
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 3 (Application Flash) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb3ap, 0x7b015480)	/* T.B.M. */
+	WDCR_EBC(PB3AP, 0x7b015480)	/* T.B.M. */
-/*3010	WDCR_EBC(pb3ap, 0x7F8FFE80)	/###* T.B.M. */
+/*3010	WDCR_EBC(PB3AP, 0x7F8FFE80)	/###* T.B.M. */
-	WDCR_EBC(pb3cr, 0x20858000)
+	WDCR_EBC(PB3CR, 0x20858000)
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 4 (Application Flash) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb4ap, 0x7b015480)	/* T.B.M. */
+	WDCR_EBC(PB4AP, 0x7b015480)	/* T.B.M. */
-/*3010	WDCR_EBC(pb4ap, 0x7F8FFE80)	/###* T.B.M. */
+/*3010	WDCR_EBC(PB4AP, 0x7F8FFE80)	/###* T.B.M. */
-	WDCR_EBC(pb4cr, 0x20C58000)
+	WDCR_EBC(PB4CR, 0x20C58000)
 
 	/*--------------------------------------------------------------- */
 	/* Memory Bank 7 (Heathrow chip) initialization */
 	/*--------------------------------------------------------------- */
-	WDCR_EBC(pb7ap, 0x02000280)	/* No Ready, 4 wait states */
+	WDCR_EBC(PB7AP, 0x02000280)	/* No Ready, 4 wait states */
-	WDCR_EBC(pb7cr, 0X4001A000)
+	WDCR_EBC(PB7CR, 0X4001A000)
 
 setup_continue:
 
@@ -294,7 +294,7 @@ sdram_init:
 	/* Read  PLL feedback divider and calculate clock period of local bus in */
 	/* granularity of 10 ps. Save clock period in r30 */
 	/*-------------------------------------------------------------- */
-	mfdcr	r4, pllmd
+	mfdcr	r4, CPC0_PLLMR
 	addi	r9, 0, 25
 	srw	r4, r4, r9
 	andi.	r4, r4, 0x07
@@ -383,8 +383,8 @@ sdram_init:
 	/* Set SDTR1  */
 	/*----------------------------------------------------------- */
 	addi    r5,0,mem_sdtr1
-	mtdcr   memcfga,r5
+	mtdcr   SDRAM0_CFGADDR,r5
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 	/*----------------------------------------------------------- */
 	/* */
@@ -414,8 +414,8 @@ sdram_init:
 	/* Set SDRAM bank 0 register and adjust r6 for next bank */
 	/*------------------------------------------------------ */
 	addi    r7,0,mem_mb0cf
-	mtdcr   memcfga,r7
+	mtdcr   SDRAM0_CFGADDR,r7
-	mtdcr   memcfgd,r6
+	mtdcr   SDRAM0_CFGDATA,r6
 
 	add	r6, r6, r15	/* add bank size to base address for next bank */
 
@@ -425,16 +425,16 @@ sdram_init:
 	bne	b1skip
 
 	addi    r7,0,mem_mb1cf
-	mtdcr   memcfga,r7
+	mtdcr   SDRAM0_CFGADDR,r7
-	mtdcr   memcfgd,r6
+	mtdcr   SDRAM0_CFGDATA,r6
 
 	add	r6, r6, r15	/* add bank size to base address for next bank */
 
 	/* Set SDRAM bank 2 register and adjust r6 for next bank */
 	/*------------------------------------------------------ */
 b1skip:	addi    r7,0,mem_mb2cf
-	mtdcr   memcfga,r7
+	mtdcr   SDRAM0_CFGADDR,r7
-	mtdcr   memcfgd,r6
+	mtdcr   SDRAM0_CFGDATA,r6
 
 	add	r6, r6, r15	/* add bank size to base address for next bank */
 
@@ -444,8 +444,8 @@ b1skip:	addi    r7,0,mem_mb2cf
 	bne	b3skip
 
 	addi    r7,0,mem_mb3cf
-	mtdcr   memcfga,r7
+	mtdcr   SDRAM0_CFGADDR,r7
-	mtdcr   memcfgd,r6
+	mtdcr   SDRAM0_CFGDATA,r6
 b3skip:
 
 	/*----------------------------------------------------------- */
@@ -457,8 +457,8 @@ b3skip:
 	bl	rtr_2
 rtr_1:	addis	r7, 0, 0x03F8
 rtr_2:	addi    r4,0,mem_rtr
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
-	mtdcr   memcfgd,r7
+	mtdcr   SDRAM0_CFGDATA,r7
 
 	/*----------------------------------------------------------- */
 	/* Delay to ensure 200usec have elapsed since reset. Assume worst */
@@ -477,10 +477,10 @@ rtr_2:	addi    r4,0,mem_rtr
 	/* read/prefetch. */
 	/*----------------------------------------------------------- */
 	addi    r4,0,mem_mcopt1
-	mtdcr   memcfga,r4
+	mtdcr   SDRAM0_CFGADDR,r4
 	addis   r4,0,0x80C0             /* set DC_EN=1 */
 	ori     r4,r4,0x0000
-	mtdcr   memcfgd,r4
+	mtdcr   SDRAM0_CFGDATA,r4
 
 
 	/*----------------------------------------------------------- */
@@ -980,9 +980,9 @@ fc07:
 
 /* For CPLD */
 /* 0 + 00000 + 010 + 000 + 00 + 01 + 00 + 00 + 000 + 0 + 0 + 1 + 0 + 00000 */
-/*	WDCR_EBC(pb5ap, 0x01010040) */
+/*	WDCR_EBC(PB5AP, 0x01010040) */
-/*jsa recommendation:		WDCR_EBC(pb5ap, 0x00010040) */
+/*jsa recommendation:		WDCR_EBC(PB5AP, 0x00010040) */
-/*	WDCR_EBC(pb5cr, 0X10018000) */
+/*	WDCR_EBC(PB5CR, 0X10018000) */
 /* Access parms */
 /*   100   3      8          0    0    0 */
 /* 0x100 + 001 + 11 + 00 + 0 0000 0000 0000 = 0x10038000 */
@@ -1003,9 +1003,9 @@ fc07:
 /* Usage:	read/write */
 /* Width:	32 bit */
 
-/* Walnut fpga pb7ap */
+/* Walnut fpga PB7AP */
 /* 0      1      8         1         5         2         8            0 */
 /* 0 + 00000 + 011 + 000 + 00 + 01 + 01 + 01 + 001 + 0 + 1 + 0 + 0 + 00000 */
-/* Walnut fpga pb7cr */
+/* Walnut fpga PB7CR */
 /* 0xF0318000 */
 /*  */

board/g2000/g2000.c

@@ -58,7 +58,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000); /* ebc always driven */
+	mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
 #endif
 
 	return 0;
@@ -114,7 +114,7 @@ int checkboard (void)
 
 long int init_sdram_static_settings(void)
 {
-#define mtsdram0(reg, data)  mtdcr(memcfga,reg);mtdcr(memcfgd,data)
+#define mtsdram0(reg, data)  mtdcr(SDRAM0_CFGADDR,reg);mtdcr(SDRAM0_CFGDATA,data)
 	/* disable memcontroller so updates work */
 	mtsdram0( mem_mcopt1, MEM_MCOPT1_INIT_VAL );
 	mtsdram0( mem_rtr   , MEM_RTR_INIT_VAL   );
@@ -154,15 +154,15 @@ int do_dumpebc(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	ulong ap, cr;
 
 	printf("\nEBC registers for PPC405GP:\n");
-	mfebc(pb0ap, ap); mfebc(pb0cr, cr);
+	mfebc(PB0AP, ap); mfebc(PB0CR, cr);
 	printf("0: AP=%08lx CP=%08lx\n", ap, cr);
-	mfebc(pb1ap, ap); mfebc(pb1cr, cr);
+	mfebc(PB1AP, ap); mfebc(PB1CR, cr);
 	printf("1: AP=%08lx CP=%08lx\n", ap, cr);
-	mfebc(pb2ap, ap); mfebc(pb2cr, cr);
+	mfebc(PB2AP, ap); mfebc(PB2CR, cr);
 	printf("2: AP=%08lx CP=%08lx\n", ap, cr);
-	mfebc(pb3ap, ap); mfebc(pb3cr, cr);
+	mfebc(PB3AP, ap); mfebc(PB3CR, cr);
 	printf("3: AP=%08lx CP=%08lx\n", ap, cr);
-	mfebc(pb4ap, ap); mfebc(pb4cr, cr);
+	mfebc(PB4AP, ap); mfebc(PB4CR, cr);
 	printf("4: AP=%08lx CP=%08lx\n", ap, cr);
 	printf("\n");
 

board/gdsys/compactcenter/compactcenter.c

@@ -215,7 +215,7 @@ int board_early_init_r(void)
 		EBC_BXCR_BS_128MB : EBC_BXCR_BS_64MB;
 
 	/* Remap the NOR FLASH to 0xcn00.0000 ... 0xcfff.ffff */
-	mtebc(pb0cr, CONFIG_SYS_FLASH_BASE_PHYS_L
+	mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L
 		| bxcr_bw
 		| EBC_BXCR_BU_RW
 		| EBC_BXCR_BW_16BIT);

board/gdsys/dlvision/dlvision.c

@@ -48,7 +48,7 @@ int board_early_init_f(void)
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks
 	 * -> ca. 15 us
 	 */
-	mtebc(epcr, 0xa8400000);	/* ebc always driven */
+	mtebc(EBC0_CFG, 0xa8400000);	/* ebc always driven */
 
 	/*
 	 * setup io-latches

board/gdsys/gdppc440etx/gdppc440etx.c

@@ -42,8 +42,8 @@ int board_early_init_f(void)
 	/*
 	 * Setup the external bus controller/chip selects
 	 */
-	mfebc(xbcfg, reg);
+	mfebc(EBC0_CFG, reg);
-	mtebc(xbcfg, reg | 0x04000000);		/* Set ATC */
+	mtebc(EBC0_CFG, reg | 0x04000000);		/* Set ATC */
 
 	/*
 	 * Setup the GPIO pins
@@ -102,10 +102,10 @@ int board_early_init_f(void)
 	/*
 	 * Setup other serial configuration
 	 */
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);	/* PCI arbiter enabled */
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);	/* PCI arbiter enabled */
-	mtsdr(sdr_pfc0, 0x00003e00);	/* Pin function */
+	mtsdr(SDR0_PFC0, 0x00003e00);	/* Pin function */
-	mtsdr(sdr_pfc1, 0x00048000);	/* Pin function: UART0 has 4 pins */
+	mtsdr(SDR0_PFC1, 0x00048000);	/* Pin function: UART0 has 4 pins */
 
 	return 0;
 }
@@ -117,7 +117,7 @@ int misc_init_r(void)
 	uint sz;
 
 	/* Re-do sizing to get full correct info */
-	mfebc(pb0cr, pbcr);
+	mfebc(PB0CR, pbcr);
 
 	if (gd->bd->bi_flashsize > 0x08000000)
 		panic("Max. flash banksize is 128 MB!\n");
@@ -127,7 +127,7 @@ int misc_init_r(void)
 		sz <<= 1;
 
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtebc(pb0cr, pbcr);
+	mtebc(PB0CR, pbcr);
 
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -178,35 +178,35 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*
 	 * Set Nebula PLB4 arbiter to fair mode.
 	 */
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	/* enable 66 MHz ext. Clock */
 	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000);

board/gdsys/neo/neo.c

@@ -43,7 +43,7 @@ int board_early_init_f(void)
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks
 	 * -> ca. 15 us
 	 */
-	mtebc(epcr, 0xa8400000);	/* ebc always driven */
+	mtebc(EBC0_CFG, 0xa8400000);	/* ebc always driven */
 
 	return 0;
 }

board/jse/init.S

@@ -52,8 +52,6 @@
 #include <asm/cache.h>
 #include <asm/mmu.h>
 
-#define cpc0_cr0 0xB1
-
 	.globl	ext_bus_cntlr_init
 ext_bus_cntlr_init:
 	mflr    r4                      /* save link register */
@@ -84,16 +82,16 @@ ext_bus_cntlr_init:
 	/* Memory Bank 0 (Flash) initialization */
 	/*----------------------------------------------------------------- */
 
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0x9B01
 	ori     r4,r4,0x5480
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,0xFFF1           /* BAS=0xFFF,BS=0x0(1MB),BU=0x3(R/W), */
 	ori     r4,r4,0x8000          /* BW=0x0( 8 bits) */
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 	blr

board/jse/jse.c

@@ -62,12 +62,12 @@ int board_early_init_f (void)
 
 	/* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1,
 	   WBN=0, WBF=1, TH=0,  RE=0,  SOR=0, BEM=0, PEN=0 */
-	mtdcr (ebccfga, pb1ap);
+	mtdcr (EBC0_CFGADDR, PB1AP);
-	mtdcr (ebccfgd, 0x01011000);
+	mtdcr (EBC0_CFGDATA, 0x01011000);
 
 	/* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */
-	mtdcr (ebccfga, pb1cr);
+	mtdcr (EBC0_CFGADDR, PB1CR);
-	mtdcr (ebccfgd, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
+	mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
 
 	/* Enable the /PerWE output as /PerWE, instead of /PCIINT. */
 	/* CPC0_CR1 |= PCIPW */

board/jse/sdram.c

@@ -35,60 +35,60 @@ phys_size_t initdram (int board_type)
 	/* Configure the SDRAMS */
 
 	/* disable memory controller */
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	mtdcr (memcfgd, 0x00000000);
+	mtdcr (SDRAM0_CFGDATA, 0x00000000);
 
 	udelay (500);
 
 	/* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
-	mtdcr (memcfga, mem_besra);
+	mtdcr (SDRAM0_CFGADDR, mem_besra);
-	mtdcr (memcfgd, 0xffffffff);
+	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
 
 	/* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
-	mtdcr (memcfga, mem_besrb);
+	mtdcr (SDRAM0_CFGADDR, mem_besrb);
-	mtdcr (memcfgd, 0xffffffff);
+	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
 
 	/* Clear SDRAM0_ECCCFG (disable ECC) */
-	mtdcr (memcfga, mem_ecccf);
+	mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-	mtdcr (memcfgd, 0x00000000);
+	mtdcr (SDRAM0_CFGDATA, 0x00000000);
 
 	/* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
-	mtdcr (memcfga, mem_eccerr);
+	mtdcr (SDRAM0_CFGADDR, mem_eccerr);
-	mtdcr (memcfgd, 0xffffffff);
+	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
 
 	/* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	mtdcr (memcfgd, 0x010a4016);
+	mtdcr (SDRAM0_CFGDATA, 0x010a4016);
 
 	/* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	mtdcr (memcfgd, 0x00084001);
+	mtdcr (SDRAM0_CFGDATA, 0x00084001);
 
 	/* Memory Bank 1 Config == BA=0x04000000, SZ=64M, AM=3, BE=1 */
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	mtdcr (memcfgd, 0x04084001);
+	mtdcr (SDRAM0_CFGDATA, 0x04084001);
 
 	/* Memory Bank 2 Config ==  BE=0 */
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	mtdcr (memcfgd, 0x00000000);
+	mtdcr (SDRAM0_CFGDATA, 0x00000000);
 
 	/* Memory Bank 3 Config ==  BE=0 */
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	mtdcr (memcfgd, 0x00000000);
+	mtdcr (SDRAM0_CFGDATA, 0x00000000);
 
 	/* refresh timer = 0x400  */
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	mtdcr (memcfgd, 0x04000000);
+	mtdcr (SDRAM0_CFGDATA, 0x04000000);
 
 	/* Power management idle timer set to the default. */
-	mtdcr (memcfga, mem_pmit);
+	mtdcr (SDRAM0_CFGADDR, mem_pmit);
-	mtdcr (memcfgd, 0x07c00000);
+	mtdcr (SDRAM0_CFGDATA, 0x07c00000);
 
 	udelay (500);
 
 	/* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) */
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	mtdcr (memcfgd, 0x80e00000);
+	mtdcr (SDRAM0_CFGDATA, 0x80e00000);
 
 	return SDRAM_LEN;
 }
@@ -108,28 +108,28 @@ int testdram (void)
 #ifdef DEBUG
 	printf ("SDRAM Controller Registers --\n");
 
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_CFG   : 0x%08x\n", val);
 
-	mtdcr (memcfga, 0x24);
+	mtdcr (SDRAM0_CFGADDR, 0x24);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_STATUS: 0x%08x\n", val);
 
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_B0CR  : 0x%08x\n", val);
 
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_B1CR  : 0x%08x\n", val);
 
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_TR    : 0x%08x\n", val);
 
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	val = mfdcr (memcfgd);
+	val = mfdcr (SDRAM0_CFGDATA);
 	printf ("    SDRAM0_RTR   : 0x%08x\n", val);
 #endif
 
@@ -137,8 +137,8 @@ int testdram (void)
 	   bit. Really, there should already have been plenty of time,
 	   given it was started long ago. But, best to check. */
 	for (idx = 0; idx < 1000000; idx += 1) {
-		mtdcr (memcfga, 0x24);
+		mtdcr (SDRAM0_CFGADDR, 0x24);
-		val = mfdcr (memcfgd);
+		val = mfdcr (SDRAM0_CFGDATA);
 		if (val & 0x80000000)
 			break;
 	}

board/korat/korat.c

@@ -81,8 +81,8 @@ int board_early_init_f(void)
 	korat_buzzer(0);
 #endif
 
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, 0xb8400000);
+	mtdcr(EBC0_CFGDATA, 0xb8400000);
 
 	/*
 	 * Setup the interrupt controller polarities, triggers, etc.
@@ -157,8 +157,8 @@ int board_early_init_f(void)
 	mtsdr(SDR0_PFC1, sdr0_pfc1);
 
 	/* PCI arbiter enabled */
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);
 
 	return 0;
 }
@@ -359,12 +359,12 @@ int misc_init_r(void)
 	gd->bd->bi_flashstart = CONFIG_SYS_FLASH1_TOP - flash1_size;
 	gd->bd->bi_flashoffset = 0;
 
-	mtdcr(ebccfga, pb1cr);
+	mtdcr(EBC0_CFGADDR, PB1CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	size_val = ffs(flash1_size) - 21;
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb1cr);
+	mtdcr(EBC0_CFGADDR, PB1CR);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/*
 	 * Re-check to get correct base address
@@ -378,12 +378,12 @@ int misc_init_r(void)
 	gd->bd->bi_flashoffset =
 		CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - CONFIG_SYS_FLASH1_ADDR;
 
-	mtdcr(ebccfga, pb1cr);
+	mtdcr(EBC0_CFGADDR, PB1CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	size_val = ffs(gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE) - 21;
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb1cr);
+	mtdcr(EBC0_CFGADDR, PB1CR);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* Monitor protection ON by default */
 #if defined(CONFIG_KORAT_PERMANENT)
@@ -552,8 +552,8 @@ int misc_init_r(void)
 	 * This fix will make the MAL burst disabling patch for the Linux
 	 * EMAC driver obsolete.
 	 */
-	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
-	mtdcr(plb4_acr, reg);
+	mtdcr(PLB4_ACR, reg);
 
 	set_serial_number();
 	set_mac_addresses();
@@ -620,35 +620,35 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*
 	 * Set Nebula PLB4 arbiter to fair mode.
 	 */
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 #if defined(CONFIG_PCI_PNP)
 	hose->fixup_irq = korat_pci_fixup_irq;

board/lwmon5/lwmon5.c

@@ -38,8 +38,8 @@ int board_early_init_f(void)
 	u32 reg;
 
 	/* PLB Write pipelining disabled. Denali Core workaround */
-	mtdcr(plb0_acr, 0xDE000000);
+	mtdcr(PLB0_ACR, 0xDE000000);
-	mtdcr(plb1_acr, 0xDE000000);
+	mtdcr(PLB1_ACR, 0xDE000000);
 
 	/*--------------------------------------------------------------------
 	 * Setup the interrupt controller polarities, triggers, etc.
@@ -90,9 +90,9 @@ int board_early_init_f(void)
 
 	/* PCI arbiter disabled */
 	/* PCI Host Configuration disbaled */
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
 	reg = 0;
-	mtsdr(sdr_pci0, 0x00000000 | reg);
+	mtsdr(SDR0_PCI0, 0x00000000 | reg);
 
 	gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1);
 
@@ -157,7 +157,7 @@ int misc_init_r(void)
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
 	gd->bd->bi_flashoffset = 0;
 
-	mfebc(pb0cr, pbcr);
+	mfebc(PB0CR, pbcr);
 	switch (gd->bd->bi_flashsize) {
 	case 1 << 20:
 		size_val = 0;
@@ -185,7 +185,7 @@ int misc_init_r(void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtebc(pb0cr, pbcr);
+	mtebc(PB0CR, pbcr);
 
 	/*
 	 * Re-check to get correct base address
@@ -249,8 +249,8 @@ int misc_init_r(void)
 	 * This fix will make the MAL burst disabling patch for the Linux
 	 * EMAC driver obsolete.
 	 */
-	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
-	mtdcr(plb4_acr, reg);
+	mtdcr(PLB4_ACR, reg);
 
 	/*
 	 * Init matrix keyboard
@@ -296,35 +296,35 @@ int pci_pre_init(struct pci_controller *hose)
 	  | Set priority for all PLB3 devices to 0.
 	  | Set PLB3 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*-------------------------------------------------------------------------+
 	  | Set priority for all PLB4 devices to 0.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*-------------------------------------------------------------------------+
 	  | Set Nebula PLB4 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	return 1;
 }

board/mpl/common/flash.c

@@ -97,7 +97,7 @@ int get_boot_mode(void)
 {
 	unsigned long pbcr;
 	int res = 0;
-	pbcr = mfdcr (strap);
+	pbcr = mfdcr (CPC0_PSR);
 	if ((pbcr & PSR_ROM_WIDTH_MASK) == 0)
 		/* boot via MPS or MPS mapping */
 		res = BOOT_MPS;
@@ -123,29 +123,29 @@ void setup_cs_reloc(void)
 	/* first findout on which cs the flash is */
 	if(mode & BOOT_MPS) {
 		/* map flash high on CS1 and MPS on CS0 */
-		mtdcr (ebccfga, pb0ap);
+		mtdcr (EBC0_CFGADDR, PB0AP);
-		mtdcr (ebccfgd, MPS_AP);
+		mtdcr (EBC0_CFGDATA, MPS_AP);
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
-		mtdcr (ebccfgd, MPS_CR);
+		mtdcr (EBC0_CFGDATA, MPS_CR);
 		/* we use the default values (max values) for the flash
 		 * because its real size is not yet known */
-		mtdcr (ebccfga, pb1ap);
+		mtdcr (EBC0_CFGADDR, PB1AP);
-		mtdcr (ebccfgd, FLASH_AP);
+		mtdcr (EBC0_CFGDATA, FLASH_AP);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		mtdcr (ebccfgd, FLASH_CR_B);
+		mtdcr (EBC0_CFGDATA, FLASH_CR_B);
 	}
 	else {
 		/* map flash high on CS0 and MPS on CS1 */
-		mtdcr (ebccfga, pb1ap);
+		mtdcr (EBC0_CFGADDR, PB1AP);
-		mtdcr (ebccfgd, MPS_AP);
+		mtdcr (EBC0_CFGDATA, MPS_AP);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		mtdcr (ebccfgd, MPS_CR);
+		mtdcr (EBC0_CFGDATA, MPS_CR);
 		/* we use the default values (max values) for the flash
 		 * because its real size is not yet known */
-		mtdcr (ebccfga, pb0ap);
+		mtdcr (EBC0_CFGADDR, PB0AP);
-		mtdcr (ebccfgd, FLASH_AP);
+		mtdcr (EBC0_CFGDATA, FLASH_AP);
-		mtdcr (ebccfga, pb0cr);
+		mtdcr (EBC0_CFGADDR, PB0CR);
-		mtdcr (ebccfgd, FLASH_CR_B);
+		mtdcr (EBC0_CFGDATA, FLASH_CR_B);
 	}
 }
 
@@ -217,34 +217,34 @@ unsigned long flash_init (void)
 	}
 	if(mode & BOOT_MPS) {
 		/* flash is on CS1 */
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
-		flashcr = mfdcr (ebccfgd);
+		flashcr = mfdcr (EBC0_CFGDATA);
 		/* we map the flash high in every case */
 		flashcr&=0x0001FFFF; /* mask out address bits */
 		flashcr|= ((0-flash_info[0].size) & 0xFFF00000); /* start addr */
 		flashcr|= (i << 17); /* size addr */
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
-		mtdcr(ebccfgd, flashcr);
+		mtdcr(EBC0_CFGDATA, flashcr);
 	}
 	else {
 		/* flash is on CS0 */
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
-		flashcr = mfdcr (ebccfgd);
+		flashcr = mfdcr (EBC0_CFGDATA);
 		/* we map the flash high in every case */
 		flashcr&=0x0001FFFF; /* mask out address bits */
 		flashcr|= ((0-flash_info[0].size) & 0xFFF00000); /* start addr */
 		flashcr|= (i << 17); /* size addr */
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
-		mtdcr(ebccfgd, flashcr);
+		mtdcr(EBC0_CFGDATA, flashcr);
 	}
 #if 0
 	/* enable this (PIP405/MIP405 only) if you want to test if
 	   the relocation has be done ok.
 	   This will disable both Chipselects */
-	mtdcr (ebccfga, pb0cr);
+	mtdcr (EBC0_CFGADDR, PB0CR);
-	mtdcr (ebccfgd, 0L);
+	mtdcr (EBC0_CFGDATA, 0L);
-	mtdcr (ebccfga, pb1cr);
+	mtdcr (EBC0_CFGADDR, PB1CR);
-	mtdcr (ebccfgd, 0L);
+	mtdcr (EBC0_CFGDATA, 0L);
 	printf("CS0 & CS1 switched off for test\n");
 #endif
 	/* patch version_string */

board/mpl/mip405/init.S

@@ -55,7 +55,7 @@
   .globl ext_bus_cntlr_init
 ext_bus_cntlr_init:
   mflr   r4                      /* save link register */
-  mfdcr  r3,strap                /* get strapping reg */
+  mfdcr  r3,CPC0_PSR                /* get strapping reg */
   andi.  r0, r3, PSR_ROM_LOC     /* mask out irrelevant bits */
   bnelr                          /* jump back if PCI boot */
 
@@ -84,9 +84,9 @@ ext_bus_cntlr_init:
 	/*-----------------------------------------------------------------------
 	 * decide boot up mode
 	 *----------------------------------------------------------------------- */
-	addi		r4,0,pb0cr
+	addi		r4,0,PB0CR
-	mtdcr		ebccfga,r4
+	mtdcr		EBC0_CFGADDR,r4
-	mfdcr		r4,ebccfgd
+	mfdcr		r4,EBC0_CFGDATA
 
 	andi.		r0, r4, 0x2000			/* mask out irrelevant bits */
 	beq		0f				/* jump if 8 bit bus width */
@@ -96,18 +96,18 @@ ext_bus_cntlr_init:
    * Memory Bank 0 (16 Bit Flash) initialization
    *---------------------------------------------------------------------- */
 
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,(FLASH_AP_B)@h
 	ori     r4,r4,(FLASH_AP_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	/* BS=0x010(4MB),BU=0x3(R/W), */
 	addis   r4,0,(FLASH_CR_B)@h
 	ori     r4,r4,(FLASH_CR_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 	b				1f
 
 0:
@@ -117,66 +117,66 @@ ext_bus_cntlr_init:
 	* Memory Bank 0 Multi Purpose Socket initialization
 	*----------------------------------------------------------------------- */
 	/* 0x7F8FFE80 slowest boot */
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,(MPS_AP_B)@h
 	ori     r4,r4,(MPS_AP_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	/* BS=0x010(4MB),BU=0x3(R/W), */
 	addis   r4,0,(MPS_CR_B)@h
 	ori     r4,r4,(MPS_CR_B)@l
 
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 
 1:
   /*-----------------------------------------------------------------------
    * Memory Bank 2-3-4-5-6 (not used) initialization
    *-----------------------------------------------------------------------*/
-  addi    r4,0,pb1cr
+  addi    r4,0,PB1CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb2cr
+  addi    r4,0,PB2CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb3cr
+  addi    r4,0,PB3CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb4cr
+  addi    r4,0,PB4CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb5cr
+  addi    r4,0,PB5CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb6cr
+  addi    r4,0,PB6CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb7cr
+  addi    r4,0,PB7CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
   nop				/* pass2 DCR errata #8 */
   blr
 

board/mpl/mip405/mip405.c

@@ -256,16 +256,16 @@ int init_sdram (void)
 	gd->baudrate = 9600;
 	serial_init ();
 	/* set up the pld */
-	mtdcr (ebccfga, pb7ap);
+	mtdcr (EBC0_CFGADDR, PB7AP);
-	mtdcr (ebccfgd, PLD_AP);
+	mtdcr (EBC0_CFGDATA, PLD_AP);
-	mtdcr (ebccfga, pb7cr);
+	mtdcr (EBC0_CFGADDR, PB7CR);
-	mtdcr (ebccfgd, PLD_CR);
+	mtdcr (EBC0_CFGDATA, PLD_CR);
 	/* THIS IS OBSOLETE */
 	/* set up the board rev reg*/
-	mtdcr (ebccfga, pb5ap);
+	mtdcr (EBC0_CFGADDR, PB5AP);
-	mtdcr (ebccfgd, BOARD_AP);
+	mtdcr (EBC0_CFGDATA, BOARD_AP);
-	mtdcr (ebccfga, pb5cr);
+	mtdcr (EBC0_CFGADDR, PB5CR);
-	mtdcr (ebccfgd, BOARD_CR);
+	mtdcr (EBC0_CFGDATA, BOARD_CR);
 #ifdef SDRAM_DEBUG
 	/* get all informations from PLD */
 	serial_puts ("\nPLD Part  0x");
@@ -289,30 +289,30 @@ int init_sdram (void)
 		SDRAM_err ("U-Boot configured for a MIP405 not for a MIP405T!!!\n");
 #endif
 	/* set-up the chipselect machine */
-	mtdcr (ebccfga, pb0cr);		/* get cs0 config reg */
+	mtdcr (EBC0_CFGADDR, PB0CR);		/* get cs0 config reg */
-	tmp = mfdcr (ebccfgd);
+	tmp = mfdcr (EBC0_CFGDATA);
 	if ((tmp & 0x00002000) == 0) {
 		/* MPS Boot, set up the flash */
-		mtdcr (ebccfga, pb1ap);
+		mtdcr (EBC0_CFGADDR, PB1AP);
-		mtdcr (ebccfgd, FLASH_AP);
+		mtdcr (EBC0_CFGDATA, FLASH_AP);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		mtdcr (ebccfgd, FLASH_CR);
+		mtdcr (EBC0_CFGDATA, FLASH_CR);
 	} else {
 		/* Flash boot, set up the MPS */
-		mtdcr (ebccfga, pb1ap);
+		mtdcr (EBC0_CFGADDR, PB1AP);
-		mtdcr (ebccfgd, MPS_AP);
+		mtdcr (EBC0_CFGDATA, MPS_AP);
-		mtdcr (ebccfga, pb1cr);
+		mtdcr (EBC0_CFGADDR, PB1CR);
-		mtdcr (ebccfgd, MPS_CR);
+		mtdcr (EBC0_CFGDATA, MPS_CR);
 	}
 	/* set up UART0 (CS2) and UART1 (CS3) */
-	mtdcr (ebccfga, pb2ap);
+	mtdcr (EBC0_CFGADDR, PB2AP);
-	mtdcr (ebccfgd, UART0_AP);
+	mtdcr (EBC0_CFGDATA, UART0_AP);
-	mtdcr (ebccfga, pb2cr);
+	mtdcr (EBC0_CFGADDR, PB2CR);
-	mtdcr (ebccfgd, UART0_CR);
+	mtdcr (EBC0_CFGDATA, UART0_CR);
-	mtdcr (ebccfga, pb3ap);
+	mtdcr (EBC0_CFGADDR, PB3AP);
-	mtdcr (ebccfgd, UART1_AP);
+	mtdcr (EBC0_CFGDATA, UART1_AP);
-	mtdcr (ebccfga, pb3cr);
+	mtdcr (EBC0_CFGADDR, PB3CR);
-	mtdcr (ebccfgd, UART1_CR);
+	mtdcr (EBC0_CFGDATA, UART1_CR);
 	bc = in8 (PLD_BOARD_CFG_REG);
 #ifdef SDRAM_DEBUG
 	serial_puts ("\nstart SDRAM Setup\n");
@@ -348,8 +348,8 @@ int init_sdram (void)
 	/* trc_clocks is sum of trp_clocks + tras_clocks */
 	trc_clocks = trp_clocks + tras_clocks;
 	/* get SDRAM timing register */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	sdram_tim = mfdcr (memcfgd) & ~0x018FC01F;
+	sdram_tim = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
 	/* insert CASL value */
 	sdram_tim |= ((unsigned long) (cal_val)) << 23;
 	/* insert PTA value */
@@ -369,8 +369,8 @@ int init_sdram (void)
 	/* insert SZ value; */
 	tmp |= ((unsigned long) sdram_table[i].sz << 17);
 	/* get SDRAM bank 0 register */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	sdram_bank = mfdcr (memcfgd) & ~0xFFCEE001;
+	sdram_bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
 	sdram_bank |= (baseaddr | tmp | 0x01);
 
 #ifdef SDRAM_DEBUG
@@ -380,8 +380,8 @@ int init_sdram (void)
 #endif
 
 	/* write SDRAM timing register */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	mtdcr (memcfgd, sdram_tim);
+	mtdcr (SDRAM0_CFGDATA, sdram_tim);
 
 #ifdef SDRAM_DEBUG
 	serial_puts ("mb0cf: ");
@@ -390,23 +390,23 @@ int init_sdram (void)
 #endif
 
 	/* write SDRAM bank 0 register */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	mtdcr (memcfgd, sdram_bank);
+	mtdcr (SDRAM0_CFGDATA, sdram_bank);
 
 	if (get_bus_freq (tmp) > 110000000) {	/* > 110MHz */
 		/* get SDRAM refresh interval register */
-		mtdcr (memcfga, mem_rtr);
+		mtdcr (SDRAM0_CFGADDR, mem_rtr);
-		tmp = mfdcr (memcfgd) & ~0x3FF80000;
+		tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
 		tmp |= 0x07F00000;
 	} else {
 		/* get SDRAM refresh interval register */
-		mtdcr (memcfga, mem_rtr);
+		mtdcr (SDRAM0_CFGADDR, mem_rtr);
-		tmp = mfdcr (memcfgd) & ~0x3FF80000;
+		tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
 		tmp |= 0x05F00000;
 	}
 	/* write SDRAM refresh interval register */
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 	/* enable ECC if used */
 #if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI)
 	if (sdram_table[i].ecc) {
@@ -415,19 +415,19 @@ int init_sdram (void)
 #ifdef SDRAM_DEBUG
 		serial_puts ("disable ECC.. ");
 #endif
-		mtdcr (memcfga, mem_ecccf);
+		mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-		tmp = mfdcr (memcfgd);
+		tmp = mfdcr (SDRAM0_CFGDATA);
 		tmp &= 0xff0fffff;		/* disable all banks */
-		mtdcr (memcfga, mem_ecccf);
+		mtdcr (SDRAM0_CFGADDR, mem_ecccf);
 		/* set up SDRAM Controller with ECC enabled */
 #ifdef SDRAM_DEBUG
 		serial_puts ("setup SDRAM Controller.. ");
 #endif
-		mtdcr (memcfgd, tmp);
+		mtdcr (SDRAM0_CFGDATA, tmp);
-		mtdcr (memcfga, mem_mcopt1);
+		mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-		tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
+		tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
-		mtdcr (memcfga, mem_mcopt1);
+		mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-		mtdcr (memcfgd, tmp);
+		mtdcr (SDRAM0_CFGDATA, tmp);
 		udelay (600);
 #ifdef SDRAM_DEBUG
 		serial_puts ("fill the memory..\n");
@@ -447,19 +447,19 @@ int init_sdram (void)
 		serial_puts ("enable ECC\n");
 #endif
 		udelay (400);
-		mtdcr (memcfga, mem_ecccf);
+		mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-		tmp = mfdcr (memcfgd);
+		tmp = mfdcr (SDRAM0_CFGDATA);
 		tmp |= 0x00800000;		/* enable bank 0 */
-		mtdcr (memcfgd, tmp);
+		mtdcr (SDRAM0_CFGDATA, tmp);
 		udelay (400);
 	} else
 #endif
 	{
 		/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
-		mtdcr (memcfga, mem_mcopt1);
+		mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-		tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80C00000;
+		tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80C00000;
-		mtdcr (memcfga, mem_mcopt1);
+		mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-		mtdcr (memcfgd, tmp);
+		mtdcr (SDRAM0_CFGDATA, tmp);
 		udelay (400);
 	}
 	serial_puts ("\n");
@@ -631,14 +631,14 @@ phys_size_t initdram (int board_type)
 	ds = 0;
 	/* since the DRAM controller is allready set up, calculate the size with the
 	   bank registers    */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	bank_reg[0] = mfdcr (memcfgd);
+	bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	bank_reg[1] = mfdcr (memcfgd);
+	bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	bank_reg[2] = mfdcr (memcfgd);
+	bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	bank_reg[3] = mfdcr (memcfgd);
+	bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
 	TotalSize = 0;
 	for (i = 0; i < 4; i++) {
 		if ((bank_reg[i] & 0x1) == 0x1) {
@@ -648,8 +648,8 @@ phys_size_t initdram (int board_type)
 		} else
 			ds = 1;
 	}
-	mtdcr (memcfga, mem_ecccf);
+	mtdcr (SDRAM0_CFGADDR, mem_ecccf);
-	tmp = mfdcr (memcfgd);
+	tmp = mfdcr (SDRAM0_CFGDATA);
 
 	if (!tmp)
 		printf ("No ");
@@ -687,7 +687,7 @@ int misc_init_r (void)
 	rtc_get (&tm);
 	start=get_timer(0);
 	/* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
-	if (mfdcr(strap) & PSR_ROM_LOC)
+	if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
 	       mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
 
 	return (0);

board/mpl/pip405/init.S

@@ -54,7 +54,7 @@
   .globl ext_bus_cntlr_init
  ext_bus_cntlr_init:
   mflr   r4                      /* save link register */
-  mfdcr  r3,strap                /* get strapping reg */
+  mfdcr  r3,CPC0_PSR                /* get strapping reg */
   andi.  r0, r3, PSR_ROM_LOC     /* mask out irrelevant bits */
   bnelr                          /* jump back if PCI boot */
 
@@ -83,9 +83,9 @@
 	/*-----------------------------------------------------------------------
 	 * decide boot up mode
 	 *----------------------------------------------------------------------- */
-	addi		r4,0,pb0cr
+	addi		r4,0,PB0CR
-	mtdcr		ebccfga,r4
+	mtdcr		EBC0_CFGADDR,r4
-	mfdcr		r4,ebccfgd
+	mfdcr		r4,EBC0_CFGDATA
 
 	andi.		r0, r4, 0x2000			/* mask out irrelevant bits */
 	beq		0f				/* jump if 8 bit bus width */
@@ -95,18 +95,18 @@
    * Memory Bank 0 (16 Bit Flash) initialization
    *---------------------------------------------------------------------- */
 
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,(FLASH_AP_B)@h
 	ori     r4,r4,(FLASH_AP_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	/* BS=0x010(4MB),BU=0x3(R/W), */
 	addis   r4,0,(FLASH_CR_B)@h
 	ori     r4,r4,(FLASH_CR_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 	b				1f
 
 0:
@@ -115,65 +115,65 @@
 	* Memory Bank 0 Multi Purpose Socket initialization
 	*----------------------------------------------------------------------- */
 	/* 0x7F8FFE80 slowest boot */
-	addi    r4,0,pb0ap
+	addi    r4,0,PB1AP
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	addis   r4,0,(MPS_AP_B)@h
 	ori     r4,r4,(MPS_AP_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
-	addi    r4,0,pb0cr
+	addi    r4,0,PB0CR
-	mtdcr   ebccfga,r4
+	mtdcr   EBC0_CFGADDR,r4
 	/* BS=0x010(4MB),BU=0x3(R/W), */
 	addis   r4,0,(MPS_CR_B)@h
 	ori     r4,r4,(MPS_CR_B)@l
-	mtdcr   ebccfgd,r4
+	mtdcr   EBC0_CFGDATA,r4
 
 
 1:
   /*-----------------------------------------------------------------------
    * Memory Bank 2-3-4-5-6 (not used) initialization
    *-----------------------------------------------------------------------*/
-  addi    r4,0,pb1cr
+  addi    r4,0,PB1CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb2cr
+  addi    r4,0,PB2CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb3cr
+  addi    r4,0,PB3CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb4cr
+  addi    r4,0,PB4CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb5cr
+  addi    r4,0,PB5CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb6cr
+  addi    r4,0,PB6CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
 
-  addi    r4,0,pb7cr
+  addi    r4,0,PB7CR
-  mtdcr   ebccfga,r4
+  mtdcr   EBC0_CFGADDR,r4
   addis   r4,0,0x0000
   ori     r4,r4,0x0000
-  mtdcr   ebccfgd,r4
+  mtdcr   EBC0_CFGDATA,r4
   nop				/* pass2 DCR errata #8 */
   blr
 

board/mpl/pip405/pip405.c

@@ -193,10 +193,10 @@ int board_early_init_f (void)
 	unsigned char cal_index, cal_val, spd_version, spd_chksum;
 	unsigned char buf[8];
 	/* set up the config port */
-	mtdcr (ebccfga, pb7ap);
+	mtdcr (EBC0_CFGADDR, PB7AP);
-	mtdcr (ebccfgd, CONFIG_PORT_AP);
+	mtdcr (EBC0_CFGDATA, CONFIG_PORT_AP);
-	mtdcr (ebccfga, pb7cr);
+	mtdcr (EBC0_CFGADDR, PB7CR);
-	mtdcr (ebccfgd, CONFIG_PORT_CR);
+	mtdcr (EBC0_CFGDATA, CONFIG_PORT_CR);
 
 	memclk = get_bus_freq (tmemclk);
 	tmemclk = 1000000000 / (memclk / 100);	/* in 10 ps units */
@@ -361,8 +361,8 @@ int board_early_init_f (void)
 		SDRAM_err ("unsupported SDRAM");
 
 	/* get SDRAM timing register */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	tmp = mfdcr (memcfgd) & ~0x018FC01F;
+	tmp = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
 	/* insert CASL value */
 /*  tmp |= ((unsigned long)cal_val) << 23; */
 	tmp |= ((unsigned long) cal_val) << 23;
@@ -385,8 +385,8 @@ int board_early_init_f (void)
 #endif
 
 	/* write SDRAM timing register */
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 	baseaddr = CONFIG_SYS_SDRAM_BASE;
 	bank_size = (((unsigned long) density) << 22) / 2;
 	/* insert AM value */
@@ -418,8 +418,8 @@ int board_early_init_f (void)
 		SDRAM_err ("unsupported SDRAM");
 	}	/* endswitch */
 	/* get SDRAM bank 0 register */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	bank = mfdcr (memcfgd) & ~0xFFCEE001;
+	bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
 	bank |= (baseaddr | tmp | 0x01);
 #ifdef SDRAM_DEBUG
 	serial_puts ("bank0: baseaddr: ");
@@ -434,12 +434,12 @@ int board_early_init_f (void)
 	sdram_size += bank_size;
 
 	/* write SDRAM bank 0 register */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	mtdcr (memcfgd, bank);
+	mtdcr (SDRAM0_CFGDATA, bank);
 
 	/* get SDRAM bank 1 register */
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	bank = mfdcr (memcfgd) & ~0xFFCEE001;
+	bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
 	sdram_size = 0;
 
 #ifdef SDRAM_DEBUG
@@ -459,12 +459,12 @@ int board_early_init_f (void)
 	serial_puts ("\n");
 #endif
 	/* write SDRAM bank 1 register */
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	mtdcr (memcfgd, bank);
+	mtdcr (SDRAM0_CFGDATA, bank);
 
 	/* get SDRAM bank 2 register */
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	bank = mfdcr (memcfgd) & ~0xFFCEE001;
+	bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
 
 	bank |= (baseaddr | tmp | 0x01);
 
@@ -482,12 +482,12 @@ int board_early_init_f (void)
 	sdram_size += bank_size;
 
 	/* write SDRAM bank 2 register */
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	mtdcr (memcfgd, bank);
+	mtdcr (SDRAM0_CFGDATA, bank);
 
 	/* get SDRAM bank 3 register */
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	bank = mfdcr (memcfgd) & ~0xFFCEE001;
+	bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
 
 #ifdef SDRAM_DEBUG
 	serial_puts ("bank3: baseaddr: ");
@@ -509,13 +509,13 @@ int board_early_init_f (void)
 #endif
 
 	/* write SDRAM bank 3 register */
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	mtdcr (memcfgd, bank);
+	mtdcr (SDRAM0_CFGDATA, bank);
 
 
 	/* get SDRAM refresh interval register */
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	tmp = mfdcr (memcfgd) & ~0x3FF80000;
+	tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
 
 	if (tmemclk < NSto10PS (16))
 		tmp |= 0x05F00000;
@@ -523,14 +523,14 @@ int board_early_init_f (void)
 		tmp |= 0x03F80000;
 
 	/* write SDRAM refresh interval register */
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 
 	/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80E00000;
+	tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80E00000;
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	mtdcr (memcfgd, tmp);
+	mtdcr (SDRAM0_CFGDATA, tmp);
 
 
    /*-------------------------------------------------------------------------+
@@ -619,14 +619,14 @@ phys_size_t initdram (int board_type)
 	/* since the DRAM controller is allready set up,
 	 * calculate the size with the bank registers
 	 */
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	bank_reg[0] = mfdcr (memcfgd);
+	bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	bank_reg[1] = mfdcr (memcfgd);
+	bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	bank_reg[2] = mfdcr (memcfgd);
+	bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	bank_reg[3] = mfdcr (memcfgd);
+	bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
 	TotalSize = 0;
 	for (i = 0; i < 4; i++) {
 		if ((bank_reg[i] & 0x1) == 0x1) {
@@ -668,7 +668,7 @@ int misc_init_r (void)
 	gd->bd->bi_flashoffset=0;
 
 	/* if PIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
-	if (mfdcr(strap) & PSR_ROM_LOC)
+	if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
 	       mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
 
 	return (0);

board/netstal/hcu4/hcu4.c

@@ -92,7 +92,7 @@ int checkboard (void)
 	u16 index      = boardVersReg & 0x0f;
 
 	/* Cannot be done in board_early_init */
-	mtdcr(cntrl0,  CPC0_CR0_VALUE);
+	mtdcr(CPC0_CR0,  CPC0_CR0_VALUE);
 
 	/* Force /RTS to active. The board it not wired quite
 	 *  correctly to use cts/rtc flow control, so just force the

board/netstal/hcu5/hcu5.c

@@ -94,8 +94,8 @@ int board_early_init_f(void)
 	}
 	mtsdr(SDR0_CP440, 0x0EAAEA02);  /* [Nto1] = 1*/
 #endif
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	mtdcr(ebccfgd, 0xb8400000);
+	mtdcr(EBC0_CFGDATA, 0xb8400000);
 
 	/*
 	 * Setup the GPIO pins
@@ -152,8 +152,8 @@ int board_early_init_f(void)
 	mtdcr(uic2tr, 0x00000000);	/* per ref-board manual */
 	mtdcr(uic2vr, 0x00000000);	/* int31 highest, base=0x000 */
 	mtdcr(uic2sr, 0xffffffff);	/* clear all */
-	mtsdr(sdr_pfc0, 0x00003E00);	/* Pin function:  */
+	mtsdr(SDR0_PFC0, 0x00003E00);	/* Pin function:  */
-	mtsdr(sdr_pfc1, 0x00848000);	/* Pin function: UART0 has 4 pins */
+	mtsdr(SDR0_PFC1, 0x00848000);	/* Pin function: UART0 has 4 pins */
 
 	/* setup BOOT FLASH */
 	mtsdr(SDR0_CUST0, 0xC0082350);
@@ -324,7 +324,7 @@ int board_with_pci(void)
 {
 	u32 reg;
 
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
 	return (reg & SDR0_XCR_PAE_MASK);
 }
 
@@ -350,28 +350,28 @@ int pci_pre_init(struct pci_controller *hose)
 	 * Set priority for all PLB3 devices to 0.
 	 * Set PLB3 arbiter to fair mode.
 	 */
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */
+	mtdcr(PLB3_ACR, addr | 0x80000000); /* Sequoia */
 
 	/*
 	 * Set priority for all PLB4 devices to 0.
 	 */
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);  /* Sequoia */
+	mtdcr(PLB4_ACR, addr);  /* Sequoia */
 
 	/*
 	 * As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
 	 * Workaround: Disable write pipelining to DDR SDRAM by setting
 	 * PLB0_ACR[WRP] = 0.
 	 */
-	mtdcr(plb0_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
+	mtdcr(PLB0_ACR, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
 
 	/* Segment1 */
-	mtdcr(plb1_acr, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
+	mtdcr(PLB1_ACR, 0);  /* PATCH HAB: WRITE PIPELINING OFF */
 
 	return board_with_pci();
 }

board/netstal/hcu5/sdram.c

@@ -89,11 +89,11 @@ static int wait_for_dlllock(void)
 	/* -----------------------------------------------------------+
 	 * Wait for the DCC master delay line to finish calibration
 	 * ----------------------------------------------------------*/
-	mtdcr(memcfga, DDR0_17);
+	mtdcr(SDRAM0_CFGADDR, DDR0_17);
 	val = DDR0_17_DLLLOCKREG_UNLOCKED;
 
 	while (wait != 0xffff) {
-		val = mfdcr(memcfgd);
+		val = mfdcr(SDRAM0_CFGDATA);
 		if ((val & DDR0_17_DLLLOCKREG_MASK) ==
 		    DDR0_17_DLLLOCKREG_LOCKED)
 			/* dlllockreg bit on */

board/netstal/mcu25/mcu25.c

@@ -71,8 +71,8 @@ int board_early_init_f (void)
 	mtdcr(uictr, 0x00000000); /* set int trigger levels */
 	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
 
-	mtdcr(cntrl1, CPC0_CR1_VALUE);
+	mtdcr(CPC0_CR1, CPC0_CR1_VALUE);
-	mtdcr(ecr, 0x60606000);
+	mtdcr(CPC0_ECR, 0x60606000);
 	mtdcr(CPC0_EIRR, 0x7C000000);
 	out32(GPIO0_OR,		CONFIG_SYS_GPIO0_OR );
 	out32(GPIO0_TCR,	CONFIG_SYS_GPIO0_TCR);
@@ -103,7 +103,7 @@ int checkboard (void)
 	u16 index      = boardVersReg & 0xf0;
 
 	/* Cannot be done in board_early_init */
-	mtdcr(cntrl0,  CPC0_CR0_VALUE);
+	mtdcr(CPC0_CR0,  CPC0_CR0_VALUE);
 
 	/* Force /RTS to active. The board it not wired quite
 	 * correctly to use cts/rtc flow control, so just force the

board/pcs440ep/pcs440ep.c

@@ -143,9 +143,9 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup the external bus controller/chip selects
 	 *-------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(ebccfgd);
+	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfgd, reg | 0x04000000);	/* Set ATC */
+	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
 
 	/*--------------------------------------------------------------------
 	 * GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c
@@ -174,10 +174,10 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup other serial configuration
 	 *-------------------------------------------------------------------*/
-	mfsdr(sdr_pci0, reg);
+	mfsdr(SDR0_PCI0, reg);
-	mtsdr(sdr_pci0, 0x80000000 | reg);	/* PCI arbiter enabled */
+	mtsdr(SDR0_PCI0, 0x80000000 | reg);	/* PCI arbiter enabled */
-	mtsdr(sdr_pfc0, 0x00000000);	/* Pin function: enable GPIO49-63 */
+	mtsdr(SDR0_PFC0, 0x00000000);	/* Pin function: enable GPIO49-63 */
-	mtsdr(sdr_pfc1, 0x00048000);	/* Pin function: UART0 has 4 pins, select IRQ5 */
+	mtsdr(SDR0_PFC1, 0x00048000);	/* Pin function: UART0 has 4 pins, select IRQ5 */
 
 	return 0;
 }
@@ -444,8 +444,8 @@ int misc_init_r (void)
 	load_ethaddr();
 
 	/* Re-do sizing to get full correct info */
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(ebccfgd);
+	pbcr = mfdcr(EBC0_CFGDATA);
 	switch (gd->bd->bi_flashsize) {
 	case 1 << 20:
 		size_val = 0;
@@ -473,8 +473,8 @@ int misc_init_r (void)
 		break;
 	}
 	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(ebccfga, pb0cr);
+	mtdcr(EBC0_CFGADDR, PB0CR);
-	mtdcr(ebccfgd, pbcr);
+	mtdcr(EBC0_CFGDATA, pbcr);
 
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -571,35 +571,35 @@ int pci_pre_init(struct pci_controller *hose)
 	  | Set priority for all PLB3 devices to 0.
 	  | Set PLB3 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp1, addr);
+	mfsdr(SD0_AMP1, addr);
-	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb3_acr);
+	addr = mfdcr(PLB3_ACR);
-	mtdcr(plb3_acr, addr | 0x80000000);
+	mtdcr(PLB3_ACR, addr | 0x80000000);
 
 	/*-------------------------------------------------------------------------+
 	  | Set priority for all PLB4 devices to 0.
 	  +-------------------------------------------------------------------------*/
-	mfsdr(sdr_amp0, addr);
+	mfsdr(SD0_AMP0, addr);
-	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
-	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	addr = mfdcr(PLB4_ACR) | 0xa0000000;	/* Was 0x8---- */
-	mtdcr(plb4_acr, addr);
+	mtdcr(PLB4_ACR, addr);
 
 	/*-------------------------------------------------------------------------+
 	  | Set Nebula PLB4 arbiter to fair mode.
 	  +-------------------------------------------------------------------------*/
 	/* Segment0 */
-	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
-	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
-	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
-	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
-	mtdcr(plb0_acr, addr);
+	mtdcr(PLB0_ACR, addr);
 
 	/* Segment1 */
-	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
-	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
-	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
-	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
-	mtdcr(plb1_acr, addr);
+	mtdcr(PLB1_ACR, addr);
 
 	return 1;
 }

board/prodrive/alpr/alpr.c

@@ -39,7 +39,7 @@ int board_early_init_f (void)
 	/*-------------------------------------------------------------------------
 	 * Initialize EBC CONFIG
 	 *-------------------------------------------------------------------------*/
-	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
 	      EBC_CFG_PTD_DISABLE | EBC_CFG_RTC_64PERCLK |
 	      EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
 	      EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
@@ -96,7 +96,7 @@ int board_early_init_f (void)
 	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
 
 	/* Setup GPIO/IRQ multiplexing */
-	mtsdr(sdr_pfc0, 0x01a33e00);
+	mtsdr(SDR0_PFC0, 0x01a33e00);
 
 	return 0;
 }
@@ -165,7 +165,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The ocotea board is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;

board/prodrive/p3p440/p3p440.c

@@ -85,14 +85,14 @@ int board_early_init_f(void)
 	/*--------------------------------------------------------------------
 	 * Setup the external bus controller/chip selects
 	 *-------------------------------------------------------------------*/
-	mtdcr(ebccfga, xbcfg);
+	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(ebccfgd);
+	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(ebccfgd, reg | 0x04000000);	/* Set ATC */
+	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
 
 	/*--------------------------------------------------------------------
 	 * Setup pin multiplexing (GPIO/IRQ...)
 	 *-------------------------------------------------------------------*/
-	mtdcr(cpc0_gpio, 0x03F01F80);
+	mtdcr(CPC0_GPIO, 0x03F01F80);
 
 	out32(GPIO0_ODR, 0x00000000);	/* no open drain pins      */
 	out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
@@ -153,12 +153,12 @@ int misc_init_r (void)
 	 * Check if only one FLASH bank is available
 	 */
 	if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
-		mtebc(pb1cr, 0);			/* disable cs */
+		mtebc(PB1CR, 0);			/* disable cs */
-		mtebc(pb1ap, 0);
+		mtebc(PB1AP, 0);
-		mtebc(pb2cr, 0);			/* disable cs */
+		mtebc(PB2CR, 0);			/* disable cs */
-		mtebc(pb2ap, 0);
+		mtebc(PB2AP, 0);
-		mtebc(pb3cr, 0);			/* disable cs */
+		mtebc(PB3CR, 0);			/* disable cs */
-		mtebc(pb3ap, 0);
+		mtebc(PB3AP, 0);
 	}
 
 	return 0;
@@ -185,7 +185,7 @@ int pci_pre_init(struct pci_controller *hose)
 	 *	The P3P440 board is always configured as the host & requires the
 	 *	PCI arbiter to be disabled because it's an PMC module.
 	 *--------------------------------------------------------------------------*/
-	strap = mfdcr(cpc0_strp1);
+	strap = mfdcr(CPC0_STRP1);
 	if (strap & 0x00100000) {
 		printf("PCI: CPC0_STRP1[PAE] set.\n");
 		return 0;

board/sandburst/common/sb_common.c

@@ -322,7 +322,7 @@ int pci_pre_init(struct pci_controller * hose )
 	 *	The metrobox is always configured as the host & requires the
 	 *	PCI arbiter to be enabled.
 	 *--------------------------------------------------------------------------*/
-	mfsdr(sdr_sdstp1, strap);
+	mfsdr(SDR0_SDSTP1, strap);
 	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
 		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
 		return 0;

board/sandburst/karef/karef.c

@@ -67,7 +67,7 @@ int board_early_init_f (void)
 	ppc440_gpio_regs_t *gpio_regs;
 
 	/* Enable GPIO interrupts */
-	mtsdr(sdr_pfc0, 0x00103E00);
+	mtsdr(SDR0_PFC0, 0x00103E00);
 
 	/* Setup access for LEDs, and system topology info */
 	gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
@@ -80,7 +80,7 @@ int board_early_init_f (void)
 	/*--------------------------------------------------------------------+
 	  | Initialize EBC CONFIG
 	  +-------------------------------------------------------------------*/
-	mtebc(xbcfg,
+	mtebc(EBC0_CFG,
 	      EBC_CFG_LE_UNLOCK	   | EBC_CFG_PTD_ENABLE |
 	      EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
 	      EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
@@ -90,7 +90,7 @@ int board_early_init_f (void)
 	/*--------------------------------------------------------------------+
 	  | 1/2 MB FLASH. Initialize bank 0 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb0ap,
+	mtebc(PB0AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -98,12 +98,12 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+	mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
 	/*--------------------------------------------------------------------+
 	  | 8KB NVRAM/RTC. Initialize bank 1 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb1ap,
+	mtebc(PB1AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -111,13 +111,13 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+	mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
 
 	/*--------------------------------------------------------------------+
 	  | Compact Flash, uses 2 Chip Selects (2 & 6)
 	  +-------------------------------------------------------------------*/
-	mtebc(pb2ap,
+	mtebc(PB2AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -125,40 +125,40 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) |
+	mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
 
 	/*--------------------------------------------------------------------+
 	  | KaRef Scan FPGA. Initialize bank 3 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb5ap,
+	mtebc(PB5AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48200000) |
+	mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48200000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+
 	  | MAC A & B for Kamino.  OFEM FPGA decodes the addresses
 	  | Initialize bank 4 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb4ap,
+	mtebc(PB4AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) |
+	mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) |
 	      EBC_BXCR_BS_2MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+
 	  | OFEM FPGA  Initialize bank 5 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb3ap,
+	mtebc(PB3AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
@@ -166,14 +166,14 @@ int board_early_init_f (void)
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
 
-	mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48400000) |
+	mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48400000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 
 	/*--------------------------------------------------------------------+
 	  | Compact Flash, uses 2 Chip Selects (2 & 6)
 	  +-------------------------------------------------------------------*/
-	mtebc(pb6ap,
+	mtebc(PB6AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -181,20 +181,20 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) |
+	mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
 
 	/*--------------------------------------------------------------------+
 	  | BME-32. Initialize bank 7 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb7ap,
+	mtebc(PB7AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) |
+	mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+

board/sandburst/metrobox/metrobox.c

@@ -57,7 +57,7 @@ int board_early_init_f (void)
 	ppc440_gpio_regs_t *gpio_regs;
 
 	/* Enable GPIO interrupts */
-	mtsdr(sdr_pfc0, 0x00103E00);
+	mtsdr(SDR0_PFC0, 0x00103E00);
 
 	/* Setup access for LEDs, and system topology info */
 	gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
@@ -70,7 +70,7 @@ int board_early_init_f (void)
 	/*--------------------------------------------------------------------+
 	  | Initialize EBC CONFIG
 	  +-------------------------------------------------------------------*/
-	mtebc(xbcfg,
+	mtebc(EBC0_CFG,
 	      EBC_CFG_LE_UNLOCK	   | EBC_CFG_PTD_ENABLE |
 	      EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
 	      EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
@@ -80,7 +80,7 @@ int board_early_init_f (void)
 	/*--------------------------------------------------------------------+
 	  | 1/2 MB FLASH. Initialize bank 0 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb0ap,
+	mtebc(PB0AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -88,12 +88,12 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+	mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
 	/*--------------------------------------------------------------------+
 	  | 8KB NVRAM/RTC. Initialize bank 1 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb1ap,
+	mtebc(PB1AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -101,13 +101,13 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+	mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
 
 	/*--------------------------------------------------------------------+
 	  | Compact Flash, uses 2 Chip Selects (2 & 6)
 	  +-------------------------------------------------------------------*/
-	mtebc(pb2ap,
+	mtebc(PB2AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -115,20 +115,20 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) |
+	mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
 
 	/*--------------------------------------------------------------------+
 	  | OPTO & OFEM FPGA. Initialize bank 3 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb3ap,
+	mtebc(PB3AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48200000) |
+	mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48200000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+
@@ -136,34 +136,34 @@ int board_early_init_f (void)
 	  | MAC A & B for Kamino.  OFEM FPGA decodes the addresses
 	  | Initialize bank 4 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb4ap,
+	mtebc(PB4AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) |
+	mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+
 	  | Metrobox MAC B  Initialize bank 5 with default values.
 	  | KA REF FPGA	 Initialize bank 5 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb5ap,
+	mtebc(PB5AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48700000) |
+	mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48700000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+
 	  | Compact Flash, uses 2 Chip Selects (2 & 6)
 	  +-------------------------------------------------------------------*/
-	mtebc(pb6ap,
+	mtebc(PB6AP,
 	      EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
 	      EBC_BXAP_BCE_DISABLE  | EBC_BXAP_CSN_ENCODE(1) |
 	      EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -171,20 +171,20 @@ int board_early_init_f (void)
 	      EBC_BXAP_RE_DISABLED  | EBC_BXAP_BEM_WRITEONLY |
 	      EBC_BXAP_PEN_DISABLED);
 
-	mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) |
+	mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
 
 	/*--------------------------------------------------------------------+
 	  | BME-32. Initialize bank 7 with default values.
 	  +-------------------------------------------------------------------*/
-	mtebc(pb7ap,
+	mtebc(PB7AP,
 	      EBC_BXAP_RE_ENABLED    | EBC_BXAP_SOR_NONDELAYED |
 	      EBC_BXAP_BME_DISABLED  | EBC_BXAP_TWT_ENCODE(3) |
 	      EBC_BXAP_TH_ENCODE(1)  | EBC_BXAP_WBF_ENCODE(0) |
 	      EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
 	      EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
 
-	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) |
+	mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) |
 	      EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
 
 	/*--------------------------------------------------------------------+

board/sbc405/sbc405.c

@@ -52,7 +52,7 @@ int board_early_init_f (void)
 	/*
 	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
-	mtebc (epcr, 0xa8400000);
+	mtebc (EBC0_CFG, 0xa8400000);
 
 	return 0;
 }

board/sc3/init.S

@@ -58,7 +58,7 @@ ext_bus_cntlr_init:
  * We need the current boot up configuration to set correct
  * timings into internal flash and external flash
  */
-		mfdcr r24,strap			/* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
+		mfdcr r24,CPC0_PSR		/* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
 						   0 0 -> 8 bit external ROM
 						   0 1 -> 16 bit internal ROM */
 		addi r4,0,2
@@ -113,8 +113,8 @@ ext_bus_cntlr_init:
  * We only have to change the timing. Mapping is ok by boot-strapping
  *----------------------------------------------------------------------- */
 
-		li r4,pb0ap				/* PB0AP=Peripheral Bank 0 Access Parameters */
+		li r4,PB1AP				/* PB0AP=Peripheral Bank 0 Access Parameters */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		mr r4,r26				/* assume internal fast flash is boot flash */
 		cmpwi r24,0x2000			/* assumption true? ... */
@@ -122,27 +122,27 @@ ext_bus_cntlr_init:
 		mr r4,r25				/* ...no, use the slow variant */
 		mr r25,r26				/* use this for the other flash */
 1:
-		mtdcr ebccfgd,r4			/* change timing now */
+		mtdcr EBC0_CFGDATA,r4			/* change timing now */
 
-		li r4,pb0cr				/* PB0CR=Peripheral Bank 0 Control Register */
+		li r4,PB0CR				/* PB0CR=Peripheral Bank 0 Control Register */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
-		mfdcr r4,ebccfgd
+		mfdcr r4,EBC0_CFGDATA
 		lis r3,0x0001
 		ori r3,r3,0x8000			/* allow reads and writes */
 		or r4,r4,r3
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 /*-----------------------------------------------------------------------
  * Memory Bank 3 (Second-Flash) initialization
  * 0xF0000000...0xF01FFFFF -> 2MB
  *----------------------------------------------------------------------- */
 
-		li r4,pb3ap				/* Peripheral Bank 1 Access Parameter */
+		li r4,PB3AP				/* Peripheral Bank 1 Access Parameter */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
-		mtdcr ebccfgd,r2			/* change timing */
+		mtdcr EBC0_CFGDATA,r2			/* change timing */
 
-		li r4,pb3cr				/* Peripheral Bank 1 Configuration Registers */
+		li r4,PB3CR				/* Peripheral Bank 1 Configuration Registers */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0xF003
 		ori r4,r4,0x8000
@@ -151,7 +151,7 @@ ext_bus_cntlr_init:
  */
 		xori r24,r24,0x2000			/* invert current bus width */
 		or r4,r4,r24
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 /*-----------------------------------------------------------------------
  * Memory Bank 1 (NAND-Flash) initialization
@@ -169,28 +169,28 @@ ext_bus_cntlr_init:
  * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold)
  *----------------------------------------------------------------------- */
 
-		li r4,pb1ap				/* Peripheral Bank 1 Access Parameter */
+		li r4,PB1AP				/* Peripheral Bank 1 Access Parameter */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0x0000
 		ori r4,r4,0x0200
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
-		li r4,pb1cr				/* Peripheral Bank 1 Configuration Registers */
+		li r4,PB1CR				/* Peripheral Bank 1 Configuration Registers */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0x77D1
 		ori r4,r4,0x8000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 
 /* USB init (without acceleration) */
 #ifndef CONFIG_ISP1161_PRESENT
-		li r4,pb4ap				/* PB4AP=Peripheral Bank 4 Access Parameters */
+		li r4,PB4AP				/* PB4AP=Peripheral Bank 4 Access Parameters */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 		lis r4,0x0180
 		ori r4,r4,0x5940
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 #endif
 
 /*-----------------------------------------------------------------------
@@ -204,8 +204,8 @@ ext_bus_cntlr_init:
  A7/A24=0 -> memory cycle
  A7/ /A24=1 -> I/O cycle
 */
-		li r4,pb2ap				/* PB2AP=Peripheral Bank 2 Access Parameters */
+		li r4,PB2AP				/* PB2AP=Peripheral Bank 2 Access Parameters */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 /*
  We emulate an ISA access
 
@@ -226,58 +226,58 @@ ext_bus_cntlr_init:
 		lis r4,0x0100
 		ori r4,r4,0x0340
 #endif
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 #ifdef IDE_USES_ISA_EMULATION
-		li r25,pb5ap				/* PB5AP=Peripheral Bank 5 Access Parameters */
+		li r25,PB5AP				/* PB5AP=Peripheral Bank 5 Access Parameters */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 #endif
 
-		li r25,pb6ap				/* PB6AP=Peripheral Bank 6 Access Parameters */
+		li r25,PB6AP				/* PB6AP=Peripheral Bank 6 Access Parameters */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
-		li r25,pb7ap				/* PB7AP=Peripheral Bank 7 Access Parameters */
+		li r25,PB7AP				/* PB7AP=Peripheral Bank 7 Access Parameters */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
-		li r25,pb2cr				/* PB2CR=Peripheral Bank 2 Configuration Register */
+		li r25,PB2CR				/* PB2CR=Peripheral Bank 2 Configuration Register */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
 
 		lis r4,0x780B
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 /*
  * the other areas are only 1MiB in size
  */
 		lis r4,0x7401
 		ori r4,r4,0xA000
 
-		li r25,pb6cr				/* PB6CR=Peripheral Bank 6 Configuration Register */
+		li r25,PB6CR				/* PB6CR=Peripheral Bank 6 Configuration Register */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
 		lis r4,0x7401
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
-		li r25,pb7cr				/* PB7CR=Peripheral Bank 7 Configuration Register */
+		li r25,PB7CR				/* PB7CR=Peripheral Bank 7 Configuration Register */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
 		lis r4,0x7411
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 #ifndef CONFIG_ISP1161_PRESENT
-		li r25,pb4cr				/* PB4CR=Peripheral Bank 4 Configuration Register */
+		li r25,PB4CR				/* PB4CR=Peripheral Bank 4 Configuration Register */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
 		lis r4,0x7421
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 #endif
 #ifdef IDE_USES_ISA_EMULATION
-		li r25,pb5cr				/* PB5CR=Peripheral Bank 5 Configuration Register */
+		li r25,PB5CR				/* PB5CR=Peripheral Bank 5 Configuration Register */
-		mtdcr ebccfga,r25
+		mtdcr EBC0_CFGADDR,r25
 		lis r4,0x0000
 		ori r4,r4,0x0000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 #endif
 
 /*-----------------------------------------------------------------------
@@ -315,19 +315,19 @@ ext_bus_cntlr_init:
 
 #ifdef CONFIG_ISP1161_PRESENT
 
-		li r4,pb4ap				/* PB4AP=Peripheral Bank 4 Access Parameters */
+		li r4,PB4AP				/* PB4AP=Peripheral Bank 4 Access Parameters */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0x030D
 		ori r4,r4,0x5E80
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
-		li r4,pb4cr				/* PB2CR=Peripheral Bank 4 Configuration Register */
+		li r4,PB4CR				/* PB2CR=Peripheral Bank 4 Configuration Register */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0x77C1
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
 #endif
 
@@ -352,28 +352,28 @@ ext_bus_cntlr_init:
  *
  *----------------------------------------------------------------------- */
 
-		li r4,pb5ap
+		li r4,PB5AP
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 		lis r4,0x040C
 		ori r4,r4,0x0200
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 
-		li r4,pb5cr			/* PB2CR=Peripheral Bank 2 Configuration Register */
+		li r4,PB5CR			/* PB2CR=Peripheral Bank 2 Configuration Register */
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0x7A01
 		ori r4,r4,0xA000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 #endif
 /*
  * External Peripheral Control Register
  */
-		li r4,epcr
+		li r4,EBC0_CFG
-		mtdcr ebccfga,r4
+		mtdcr EBC0_CFGADDR,r4
 
 		lis r4,0xB84E
 		ori r4,r4,0xF000
-		mtdcr ebccfgd,r4
+		mtdcr EBC0_CFGDATA,r4
 /*
  * drive POST code
  */

board/sc3/sc3.c

@@ -199,14 +199,14 @@ int board_start_ide(void)
 static int sc3_cameron_init (void)
 {
 	/* Set up the Memory Controller for the CAMERON version */
-	mtebc (pb4ap, 0x01805940);
+	mtebc (PB4AP, 0x01805940);
-	mtebc (pb4cr, 0x7401a000);
+	mtebc (PB4CR, 0x7401a000);
-	mtebc (pb5ap, 0x01805940);
+	mtebc (PB5AP, 0x01805940);
-	mtebc (pb5cr, 0x7401a000);
+	mtebc (PB5CR, 0x7401a000);
-	mtebc (pb6ap, 0x0);
+	mtebc (PB6AP, 0x0);
-	mtebc (pb6cr, 0x0);
+	mtebc (PB6CR, 0x0);
-	mtebc (pb7ap, 0x0);
+	mtebc (PB7AP, 0x0);
-	mtebc (pb7cr, 0x0);
+	mtebc (PB7CR, 0x0);
 	return 0;
 }
 
@@ -312,18 +312,18 @@ int board_early_init_f (void)
 	mtdcr (uicsr, 0xFFFFFFFF);    /* clear all ints */
 
 	/* setup other implementation specific details */
-	mtdcr (ecr, 0x60606000);
+	mtdcr (CPC0_ECR, 0x60606000);
 
-	mtdcr (cntrl1, 0x000042C0);
+	mtdcr (CPC0_CR1, 0x000042C0);
 
 	if (IS_CAMERON) {
-		mtdcr (cntrl0, 0x01380000);
+		mtdcr (CPC0_CR0, 0x01380000);
 		/* Setup the GPIOs */
 		writel (0x08008000, 0xEF600700);	/* Output states */
 		writel (0x00000000, 0xEF600718);	/* Open Drain control */
 		writel (0x68098000, 0xEF600704);	/* Output control */
 	} else {
-		mtdcr (cntrl0,0x00080000);
+		mtdcr (CPC0_CR0,0x00080000);
 		/* Setup the GPIOs */
 		writel (0x08000000, 0xEF600700);	/* Output states */
 		writel (0x14000000, 0xEF600718);	/* Open Drain control */
@@ -331,13 +331,13 @@ int board_early_init_f (void)
 	}
 
 	/* Code decompression disabled */
-	mtdcr (kiar, kconf);
+	mtdcr (KIAR, KCONF);
-	mtdcr (kidr, 0x2B);
+	mtdcr (KIDR, 0x2B);
 
 	/* CPC0_ER: enable sleep mode of (currently) unused components */
 	/* CPC0_FR: force unused components into sleep mode */
-	mtdcr (cpmer, 0x3F800000);
+	mtdcr (CPMER, 0x3F800000);
-	mtdcr (cpmfr, 0x14000000);
+	mtdcr (CPMFR, 0x14000000);
 
 	/* set PLB priority */
 	mtdcr (0x87, 0x08000000);
@@ -472,19 +472,19 @@ static void printCSConfig(int reg,unsigned long ap,unsigned long cr)
 
 #ifdef SC3_DEBUGOUT
 
-static unsigned int ap[] = {pb0ap, pb1ap, pb2ap, pb3ap, pb4ap,
+static unsigned int ap[] = {PB0AP, PB1AP, PB2AP, PB3AP, PB4AP,
-				pb5ap, pb6ap, pb7ap};
+				PB5AP, PB6AP, PB7AP};
-static unsigned int cr[] = {pb0cr, pb1cr, pb2cr, pb3cr, pb4cr,
+static unsigned int cr[] = {PB0CR, PB1CR, PB2CR, PB3CR, PB4CR,
-				pb5cr, pb6cr, pb7cr};
+				PB5CR, PB6CR, PB7CR};
 
 static int show_reg (int nr)
 {
 	unsigned long ul1, ul2;
 
-	mtdcr (ebccfga, ap[nr]);
+	mtdcr (EBC0_CFGADDR, ap[nr]);
-	ul1 = mfdcr (ebccfgd);
+	ul1 = mfdcr (EBC0_CFGDATA);
-	mtdcr (ebccfga, cr[nr]);
+	mtdcr (EBC0_CFGADDR, cr[nr]);
-	ul2 = mfdcr(ebccfgd);
+	ul2 = mfdcr(EBC0_CFGDATA);
 	printCSConfig(nr, ul1, ul2);
 	return 0;
 }
@@ -500,8 +500,8 @@ int checkboard (void)
 		show_reg (i);
 	}
 
-	mtdcr (ebccfga, epcr);
+	mtdcr (EBC0_CFGADDR, EBC0_CFG);
-	ul1 = mfdcr (ebccfgd);
+	ul1 = mfdcr (EBC0_CFGDATA);
 
 	puts ("\nGeneral configuration:\n");
 
@@ -591,21 +591,21 @@ phys_size_t initdram (int board_type)
 
 	puts("\nSDRAM configuration:\n");
 
-	mtdcr (memcfga, mem_mcopt1);
+	mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
-	ul1 = mfdcr(memcfgd);
+	ul1 = mfdcr(SDRAM0_CFGDATA);
 
 	if (!(ul1 & 0x80000000)) {
 		puts(" Controller disabled\n");
 		return 0;
 	}
 	for (i = 0; i < 4; i++) {
-		mtdcr (memcfga, mbcf[i]);
+		mtdcr (SDRAM0_CFGADDR, mbcf[i]);
-		ul1 = mfdcr (memcfgd);
+		ul1 = mfdcr (SDRAM0_CFGDATA);
 		mems += printSDRAMConfig (i, ul1);
 	}
 
-	mtdcr (memcfga, mem_sdtr1);
+	mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
-	ul1 = mfdcr(memcfgd);
+	ul1 = mfdcr(SDRAM0_CFGDATA);
 
 	printf ("Timing:\n -CAS latency %lu\n", ((ul1 & 0x1800000) >> 23)+1);
 	printf (" -Precharge %lu (PTA) \n", ((ul1 & 0xC0000) >> 18) + 1);
@@ -614,15 +614,15 @@ phys_size_t initdram (int board_type)
 	printf (" -CAS to RAS %lu\n", ((ul1 & 0x1C) >> 2) + 4);
 	printf (" -RAS to CAS %lu\n", ((ul1 & 0x3) + 1));
 	puts ("Misc:\n");
-	mtdcr (memcfga, mem_rtr);
+	mtdcr (SDRAM0_CFGADDR, mem_rtr);
-	ul1 = mfdcr(memcfgd);
+	ul1 = mfdcr(SDRAM0_CFGDATA);
 	printf (" -Refresh rate: %luns\n", (ul1 >> 16) * 7);
 
-	mtdcr(memcfga,mem_pmit);
+	mtdcr(SDRAM0_CFGADDR,mem_pmit);
-	ul2=mfdcr(memcfgd);
+	ul2=mfdcr(SDRAM0_CFGDATA);
 
-	mtdcr(memcfga,mem_mcopt1);
+	mtdcr(SDRAM0_CFGADDR,mem_mcopt1);
-	ul1=mfdcr(memcfgd);
+	ul1=mfdcr(SDRAM0_CFGDATA);
 
 	if (ul1 & 0x20000000)
 		printf(" -Power Down after: %luns\n",
@@ -658,8 +658,8 @@ phys_size_t initdram (int board_type)
 	else
 		puts(" -Memory lines only at write cycles active outputs\n");
 
-	mtdcr (memcfga, mem_status);
+	mtdcr (SDRAM0_CFGADDR, mem_status);
-	ul1 = mfdcr (memcfgd);
+	ul1 = mfdcr (SDRAM0_CFGDATA);
 	if (ul1 & 0x80000000)
 		puts(" -SDRAM Controller ready\n");
 	else
@@ -670,20 +670,20 @@ phys_size_t initdram (int board_type)
 
 	return (mems * 1024 * 1024);
 #else
-	mtdcr (memcfga, mem_mb0cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
-	ul1 = mfdcr (memcfgd);
+	ul1 = mfdcr (SDRAM0_CFGDATA);
 	mems = printSDRAMConfig (0, ul1);
 
-	mtdcr (memcfga, mem_mb1cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
-	ul1 = mfdcr (memcfgd);
+	ul1 = mfdcr (SDRAM0_CFGDATA);
 	mems += printSDRAMConfig (1, ul1);
 
-	mtdcr (memcfga, mem_mb2cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
-	ul1 = mfdcr(memcfgd);
+	ul1 = mfdcr(SDRAM0_CFGDATA);
 	mems += printSDRAMConfig (2, ul1);
 
-	mtdcr (memcfga, mem_mb3cf);
+	mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
-	ul1 = mfdcr(memcfgd);
+	ul1 = mfdcr(SDRAM0_CFGDATA);
 	mems += printSDRAMConfig (3, ul1);
 
 	return (mems * 1024 * 1024);

board/snmc/qs850/flash.c

@@ -104,21 +104,21 @@ unsigned long flash_init (void)
 
 	/* Re-do sizing to get full correct info */
 	if (size_b1) {
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
-		pbcr = mfdcr(ebccfgd);
+		pbcr = mfdcr(EBC0_CFGDATA);
-		mtdcr(ebccfga, pb0cr);
+		mtdcr(EBC0_CFGADDR, PB0CR);
 		base_b1 = -size_b1;
 		pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
+		mtdcr(EBC0_CFGDATA, pbcr);
 	}
 
 	if (size_b0) {
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
-		pbcr = mfdcr(ebccfgd);
+		pbcr = mfdcr(EBC0_CFGDATA);
-		mtdcr(ebccfga, pb1cr);
+		mtdcr(EBC0_CFGADDR, PB1CR);
 		base_b0 = base_b1 - size_b0;
 		pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
+		mtdcr(EBC0_CFGDATA, pbcr);
 	}
 
 	size_b0 = flash_get_size((volatile FLASH_WORD_SIZE *)base_b0, &flash_info[0]);