This fixes a SEGV error that happens the next time the statistics
are updated.
Addresses:
Program terminated with signal 11, Segmentation fault.
#0 0xb7711fa5 in rate_ctr_group_intv (grp=<optimized out>) at
rate_ctr.c:107
107 for (i = 0; i < grp->desc->num_ctr; i++) {
#0 0xb7711fa5 in rate_ctr_group_intv (grp=<optimized out>) at
rate_ctr.c:107
#1 rate_ctr_timer_cb (data=0x0) at rate_ctr.c:129
#2 0xb770ec59 in osmo_timers_update () at timer.c:243
#3 0xb770ef7a in osmo_select_main (polling=0) at select.c:133
#4 0x08049987 in main (argc=3, argv=0xbfba8084) at
gb_proxy_main.c:306
Sponsored-by: On-Waves ehf
Under special circumstances (see below) receiving a NS-RESET leads to
duplicated NS-VC entries.
This happens when the source port of a NS-VC changes to a new one
that has already been used by another NS-VC.
This patch changes gprs_ns_rx_reset() to check for this case and to
use the existing NS-VC object. The NS-VC object that was associated
with the source address before is detached from this source but kept
in the NS-VC list so that it can be reattached when a correspondent
NS-RESET is received later on. Meanwhile it will have a cleared link
layer address which will not match a real link info.
A new counter NS_CTR_REPLACED is incremented each time when the NS-VC
object is replacing another one. A new signal S_NS_REPLACED is added
which gets dispatched in this case, too.
Another new counter NS_CTR_NSEI_CHG is incremented each time when the
NSEI of a NS-VC object (with fixed NSVCI) changes.
Ticket: OW#874
Sponsored-by: On-Waves ehf
Adds the functions gprs_ns_ll_copy() and gprs_ns_ll_clear(). Renames
gprs_ns_format_peer() to gprs_ns_ll_str(). All of these functions
uniformly access the link layer part within the NS-VC objects.
Sponsored-by: On-Waves ehf
Register an osmo signal handler to print a short notice about every
SS_L_NS signal that is generated while processing the tests.
Sponsored-by: On-Waves ehf
The testcase didn't work on Ubuntu 12.04 because vty_create will
directly call vty_event (e.g. not through the plt). This means
that the approach to override vty_event in the testcase failed.
Use the signal interface of libosmocore and make the testcase
use it. The signals can be generally useful as well.
Currently when a NS-RESET is recevied over a link that has not yet
been associated with a NS-VC, the NSEI is used to find an existing
NS-VC. If one is found, the reset procedure is initiated.
This behaviour is not conformant with 3GPP TS 08.16 (see chapter
4.2.3) which allows to use several NS-VC between two endpoints in
parallel.
The patch changes the implementation to use the NSVCI instead
of the NSEI to search for an existing NS-VC object.
Ticket: OW#874
Sponsored-by: On-Waves ehf
According to 3GPP TS 08.16, 7.3 "Reset procedure" the entity
receiving a NS-RESET PDU responds with a NS-RESET-ACK and 'then'
starts the test procedure which essentially means, that a NS-ALIVE
gets sent and a timer is started.
Currently the NS-ALIVE is sent before the NS-RESET-ACK.
This patch fixes the implementation by reversing the order in which
these messages are sent.
Sponsored-by: On-Waves ehf
It started to behave weird on Debian Testing (GCC 4.8), I compiled it
with address sanitizer support and set a breakpoint in
__asan_report_error to get a backtrace.
gb/bssgp_fc_test.c: In function ‘fc_out_cb’:
gb/bssgp_fc_test.c:46:1: warning: no return statement in function returning non-void [-Wreturn-type]
gb/bssgp_fc_test.c: In function ‘fc_in’:
gb/bssgp_fc_test.c:56:1: warning: no return statement in function returning non-void [-Wreturn-type]
gb/bssgp_fc_test.c: In function ‘test_fc’:
gb/bssgp_fc_test.c:79:3: warning: implicit declaration of function ‘usleep’ [-Wimplicit-function-declaration]
This adds the vty_install_default() function that is basically the
install_default() function plus the registration of the commands
'exit' and 'end'. The latter is only provided in subnodes of
ENABLED_NODE and CONFIG_NONE.
The VTY test program is extended to check these commands.
Ticket: OW#952
The number of digits is the number of used octets times two (two
digits per octet). The result has been successfully dissected by
wireshark. It has not been tested with real phones.
Fix type of argument 'argv'.
Addresses:
conv/conv_test.c:358:5: error: second parameter of 'main' (argument
array) must
be of type 'char **'
int main(int argc, char argv[])
The 7bit<->8bit encoding/decoding functions didn't check whether
there is still enough space in the destination buffer. Therefore a
buffer size parameter has been added to each of the functions which
is used to truncate the output if the buffer is too small.
In addition, the return value of the decoding functions has been
changed to number of characters written (excluding \0), so this
value is always equal to strlen(decoded).
The old functions are still available as wrapper functions.
Renamed gsm_7bit_ussd() to test_7bit_ussd() and extended the function
to take the expected binary encoding and eventually added trailing
bytes in the re-decoded text as arguments. These are used to check
assertions of the right behaviour instead of solely relying on
regression data, because the value are determined by the spec and
fixed and it is more obvious this way. Especially concerning the case
with the duplicated \r which can easily be overlooked when it's only
present in the ok file.
Handling 7-bit coding is a little different for USSD, as TS 03.38
states:
To avoid the situation where the receiving entity confuses 7 binary
zero pad bits as the @ character, the carriage return or <CR>
character shall be used for padding in this situation [...].
If <CR> is intended to be the last character and the message
(including the wanted <CR>) ends on an octet boundary, then another
<CR> must be added together with a padding bit 0. The receiving entity
will perform the carriage return function twice, but this will not
result in misoperation as the definition of <CR> [...] is identical to
the definition of <CR><CR>.
The receiving entity shall remove the final <CR> character where the
message ends on an octet boundary with <CR> as the last character.
Jacob has verified the fix with fakeBTS and the wireshark dissector.
Fixes: OW#947
Reviewed-by: Jacob Erlbeck <jerlbeck@sysmocom.de>
Compiled with ubuntu 1204 (precise), where -Wformat-security is enabled by
-Wall.
Test yields ok, but the current implementation doesn't properly support
multi-character separators and end strings. So the test output is truncated.
Addresses:
utils.c: In function 'vty_cmd_string_from_valstr':
utils.c:84:2: warning: format not a string literal and no format arguments [-Wformat-security]
utils.c:84:2: warning: format not a string literal and no format arguments [-Wformat-security]
utils.c:108:2: warning: format not a string literal and no format arguments [-Wformat-security]
utils.c:108:2: warning: format not a string literal and no format arguments [-Wformat-security]
The &buf[3] is unlikely to be aligned properly. Use memcpy instead
of an assignment. Add a small testcase that verifies that I didn't
mess up the conversion.
Alignment trap: osmo-nitb (3293) PC=0x492b7094 Instr=0xe5803003 Address=0xbeb259db FSR 0x801
On Ubuntu 13.04 the build was failing on the OBS with:
/usr/bin/ld: fr_test.o: undefined reference to symbol 'dlsym@@GLIBC_2.2.5'
/usr/bin/ld: note: 'dlsym@@GLIBC_2.2.5' is defined in DSO /lib/x86_64-linux-gnu/libdl.so.2 so try adding it to the linker command line
/lib/x86_64-linux-gnu/libdl.so.2: could not read symbols: Invalid operation
collect2: error: ld returned 1 exit status
The issue about the wrong padding has been found when creating the
testcase in commit 15f740caa3 but the
patch to fix that was never proposed by inclusion by its author.
The issue about about the establish confirm carrying data with
a wrong size is still present.
After reception of SABM, the network responds with UA and enters the
establised multiframe state. If UA is not received by mobile, the SABM
is transmitted again, and the network must respond with UA again, unless
it is from a different mobile.
Add LAPDm collision test (contention resolution on network side).
The log target can be used via log alarms and show alarms.
Why? This feature was proposed/requested at
http://openbsc.osmocom.org/trac/wiki/Tasks/ErrorLogTarget
All messages use the same amount of space, prioritizing simplicity.
The log target can be used via log alarms and show alarms.
Why? This feature was proposed/requested at
http://openbsc.osmocom.org/trac/wiki/Tasks/ErrorLogTarget
All messages use the same amount of space, prioritizing simplicity.
The framerelay code is seldomly used and the socket clean ups introduced
a regression. Create a testcase that will work as a user not having the
right capabilities to create raw sockets.
We have to make sure that this test is working even when not ran as root.
The easiest way to do this is to provide our own socket implementation.
This is done with dlopen/dlsym to convert the raw socket request to an UDP
one.
When building out-of-srcdir, "../../config.h" fails to reach config.h
because the compiler is invoked in $builddir/tests/, not
$builddir/tests/timer/. Use "../config.h" instead; this also works
for in-srcdir builds.
Signed-off-by: Alex Badea <vamposdecampos@gmail.com>
This file is created in ./configure so we shouldn't remove it with make.
Otherwise ./configure && make clean && make check fails with:
make[3]: *** No rule to make target `atconfig', needed by `check-local'.
Stop.
lapd_test.c: In function ‘ms_to_bts_l1_cb’:
lapd_test.c:192:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
lapd_test.c:199:1: warning: no return statement in function returning non-void [-Wreturn-type]
lapd_test.c: In function ‘main’:
lapd_test.c:355:2: warning: implicit declaration of function ‘osmo_init_logging’ [-Wimplicit-function-declaration]
This was found while implementing handover on a sysmobts. When we
receive a channel release request for a channel that was never really
activated (set_lapdm_context() was not called) we segfault in
lapd_recv_dlsap().
We now return early with -EINVAL in rslms_rx_rll() if we receive a
message that assumes set_lapdm_context() was already called.
These are:
* RSL_MT_UNIT_DATA_REQ
* RSL_MT_DATA_REQ
* RSL_MT_SUSP_REQ
* RSL_MT_REL_REQ
A test case was added to trigger the issue.
* Disable color and printing the filename of the stderr log target,
update the results
* Add the .ok, .err and .sh files to the extra_dist
* Execute the shell script from the source directory
Jacob Erlbeck
Harald Welte
Sylvain Munaut