Currently those messages are answered by a NS_STATUS message when
received on an uninitialised (no NS_RESET hat been seen yet) NS_VC
which violates GPP TS 08.16 7.3.1 and 7.4.1.
This patch adds checks to gprs_ns_vc_create() and eventually returns
before the error NS_STATUS message is generated.
Sponsored-by: On-Waves ehf
When a RESET is received on the same link with a different NSVCI from
a BSS on a dynamically created NS connection do not patch the nsvc
object but create a new one instead. Thus the NSVCI is never modified
at a nsvc object after the NS-VC has been established.
Sponsored-by: On-Waves ehf
This modifies the NS stack's behavior to accept RESET and RESET_ACK
NSEI changes for NS-VC dynamically created by RESET messages from
BSSes. This feature is not used for NS-VC configured via VTY or NS-VC
to a SGSN.
Sponsored-by: On-Waves ehf
This changes the implementations for the reception of RESET and
RESET_ACK to be compatible with 3GPP TS 08.16, 7.3.1:
- Just send a RESET_ACK with correct values back to the SGSN when a
RESET with an invalid NSVCI or NSEI has been received.
- Check RESET_ACK for matching NSEI and NSVCI.
- Ignore unexpected RESET_ACKs.
In addition, use RESET_ACK from a BSS to update the BSS source
address based on the NSVCI to be tolerant with changing UDP source
addresses/ports.
Sponsored-by: On-Waves ehf
This fixes a SEGV error that happens the next time the statistics
are updated.
Addresses:
Program terminated with signal 11, Segmentation fault.
#0 0xb7711fa5 in rate_ctr_group_intv (grp=<optimized out>) at
rate_ctr.c:107
107 for (i = 0; i < grp->desc->num_ctr; i++) {
#0 0xb7711fa5 in rate_ctr_group_intv (grp=<optimized out>) at
rate_ctr.c:107
#1 rate_ctr_timer_cb (data=0x0) at rate_ctr.c:129
#2 0xb770ec59 in osmo_timers_update () at timer.c:243
#3 0xb770ef7a in osmo_select_main (polling=0) at select.c:133
#4 0x08049987 in main (argc=3, argv=0xbfba8084) at
gb_proxy_main.c:306
Sponsored-by: On-Waves ehf
This adds a 'nsvc nsvci <0-65535> (block|unblock|reset)' vty
command. It selects the NS-VC based on the nsvci instead of using the
first with a matching NSEI, like it is done when the 'nsei' keyword
is used instead.
Sponsored-by: On-Waves ehf
Under special circumstances (see below) receiving a NS-RESET leads to
duplicated NS-VC entries.
This happens when the source port of a NS-VC changes to a new one
that has already been used by another NS-VC.
This patch changes gprs_ns_rx_reset() to check for this case and to
use the existing NS-VC object. The NS-VC object that was associated
with the source address before is detached from this source but kept
in the NS-VC list so that it can be reattached when a correspondent
NS-RESET is received later on. Meanwhile it will have a cleared link
layer address which will not match a real link info.
A new counter NS_CTR_REPLACED is incremented each time when the NS-VC
object is replacing another one. A new signal S_NS_REPLACED is added
which gets dispatched in this case, too.
Another new counter NS_CTR_NSEI_CHG is incremented each time when the
NSEI of a NS-VC object (with fixed NSVCI) changes.
Ticket: OW#874
Sponsored-by: On-Waves ehf
Adds the functions gprs_ns_ll_copy() and gprs_ns_ll_clear(). Renames
gprs_ns_format_peer() to gprs_ns_ll_str(). All of these functions
uniformly access the link layer part within the NS-VC objects.
Sponsored-by: On-Waves ehf
Currently this first NS-VC with a matching NSEI is always used to
send a UNITDATA message via gprs_ns_sendmsg(). If the NS-VC found is
either dead or blocked, an error is returned.
This patch changes to code to skip blocked or dead NS-VCs while
searching and return the error if no usable NS-VC is found. This
makes it possible to have several NS-VCs per connection group.
Sponsored-by: On-Waves ehf
Register an osmo signal handler to print a short notice about every
SS_L_NS signal that is generated while processing the tests.
Sponsored-by: On-Waves ehf
Currently when a NS-RESET is recevied over a link that has not yet
been associated with a NS-VC, the NSEI is used to find an existing
NS-VC. If one is found, the reset procedure is initiated.
This behaviour is not conformant with 3GPP TS 08.16 (see chapter
4.2.3) which allows to use several NS-VC between two endpoints in
parallel.
The patch changes the implementation to use the NSVCI instead
of the NSEI to search for an existing NS-VC object.
Ticket: OW#874
Sponsored-by: On-Waves ehf
According to 3GPP TS 08.16, 7.3 "Reset procedure" the entity
receiving a NS-RESET PDU responds with a NS-RESET-ACK and 'then'
starts the test procedure which essentially means, that a NS-ALIVE
gets sent and a timer is started.
Currently the NS-ALIVE is sent before the NS-RESET-ACK.
This patch fixes the implementation by reversing the order in which
these messages are sent.
Sponsored-by: On-Waves ehf
This patch refactors gprs_ns_rcvmsg() by moving the parts relevant to
the NS messages into the new functions gprs_ns_vc_create() (nsvc
object creation) and gprs_ns_process_msg() (main NS automaton). These
do not contain code that directly depends on the link layer (they
call other functions that still do). This reduces the gprs_ns_rcvmsg()
function to calling these two functions and optionally setting up the
link layer specific fields of the nsvc.
Sponsored-by: On-Waves ehf
If the BTS tells us to not send any data at all anymore (bucket leak
rate of 0 bits per second), then we should respect this and not run into
a divide-by-zero. However, as this indicates complete overload, we
print a log message to that regard.
Use FreeBSD struct iphdr definition for OSX also. From the commentary in
the source file:
On BSD the IPv4 struct is called struct ip and instead of iXX
the members are called ip_XX. One could change this code to use
struct ip but that would require to define _BSD_SOURCE and that
might have other complications. Instead make sure struct iphdr
is present on FreeBSD.
* add more comments on units of struct members
* make sure to parsre FC-BVC message correctly
* add error message in case user passes PDU larger than bucket size
* add new function to initialize flow control struct
This code is supposed to implement the BSSGP flow control algorithm,
both for the per-BSS and for the per-MS flow control.
The code currently has no test cases, they will come in a separate
commit.
The OpenSUSE build is not happy about the uint8_t to uint8_t*
assignment. As the suspend_ref is a mandatory field we can make
it a plain uint8_t. Increase the LIBVERSION as the ABI has changed.
This is a 24bit integer value, and thus we need to encode the three
least significant octets of the network-byte-order 32bit value, not the
three most significant octets.
This actually allows for the user to override the decision and at the
same time supports compilers that might not be able to use -fPIC at
all.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Jacob Erlbeck
Harald Welte
Sylvain Munaut