Since we have started to use local_amp_id for local AMP
Controller Id it makes sense to rename ctrl_id to remote_amp_id
since it represents remote AMP controller Id.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add processing L2CAP Create Chan Request. When channel is created
save associated high speed link hs_hcon.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving HCI Phylink Complete event run amp_physical_cfm
which initialize BR/EDR L2CAP channel associated with High Speed
link and run l2cap_physical_cfm which shall send L2CAP Create
Chan Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When deciding whether to send EFS configuration response with success,
check rather for existence of High Speed physical link hs_hcon then
ctrl_id. There might be cases when there is ctrl_id but high speed link
is not established yet.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Disconnect logical link for high speed channel hs_hchan
associated with L2CAP channel chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving HCI Event: Command Status for Create Physical Link
with Error code remove AMP hcon.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After physical link is created logical link needs to be created.
The process starts after L2CAP channel is created and L2CAP
Configuration Response with result PENDING is received.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When logical link creation is completed we need to save hs_hchan
which represents logical link instead of hs_hcon representing
physical link. hs_hcon shall be saved when receiving physical link
complete event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
__constant_cpu_to_le*() is the right go here.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For files only using THIS_MODULE and/or EXPORT_SYMBOL, map
them onto including export.h -- or if the file isn't even
using those, then just delete the include.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When refcnt reaches zero disconnect timeout will run and hci_conn
will be disconnected.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add processing for HCI Physical Link Complete event. Upon
successful status received start L2CAP create channel process.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There is helper function used to send EFS Configuration Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Assignment is not needed here since err is always gets value.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes sending an unnecessary HCI_LE_Host_Enable command if
the command has already been sent as part of the default HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When powered on the EIR data gets updated as the last step by mgmt.
Therefore avoid an update when getting a local name update as that's
part of the normal HCI init sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes sending an unnecessary HCI_Write_SSP_Mode command if
the command has already been sent as part of the default HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When we get a successful command complete for HCI_Write_SSP_Mode we need
to update the host feature bits for the hdev struct accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When an adapter is in the LE peripheral role scanning for other devices
or initiating connections to them is not allowed. This patch makes sure
that such attempts will result in appropriate error returns.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a flag to be used for LE GAP Peripheral role. In this
role undirected advertising will be enabled and operations not allowed
in Peripheral role (such as scanning and initiating connections) will be
disallowed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For better code readability and avoiding simple bugs of checking the
wrong byte of the features make use of feature test macros whenever
possible.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds missing feature test macros needed for various use cases
and also sorts the macros according to the feature bit location in the
feature mask (for easy lookup).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When LE has been enabled with the simultaneous BR/EDR & LE parameter set
to true we should also update the host features stored in struct hci_dev
accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch makes sure that settings which are specific for BR/EDR
capable adapters are not allowed for non-BR/EDR (e.g. LE-only) adapters.
Instead, a "not supported" error is returned of such a setting is
attempted to be set for a non-BR/EDR adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch makes sure that we don't send BR/EDR-only commands for
LE-only adapters when they get powered on. Doing this would just cause
command errors.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
le_init() and bredr_init() are now called le_setup() and bredr_setup() to
avoid duplicates names over the tree even if they are all static.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds the reading of the LE advertising channel TX power to
the HCI init sequence of LE-capable controllers. This data will be used
e.g. for inclusion in the advertising data packets when advertising is
enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds setting of the LE event mask to the HCI init procedure
for LE-capable controllers. Right now we only set the default mask which
is good enough for the events available in the 4.0 core specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes the use of le_mtu and le_pkts values in the
HCIGETDEVINFO ioctl for LE-only controllers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch splits off most the HCI init sequence commands from a fixed
set into a conditional one that is sent once the HCI_Read_Local_Features
and HCI_Read_Local_Version_Information commands complete. This is
necessary since many of the current fixed commands are not allowed for
LE-only controllers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
include <linux/export.h> is the right to go here.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Channel moves are triggered by changes to the BT_CHANNEL_POLICY
sockopt when an ERTM or streaming-mode channel is connected.
Moves are only started if enable_hs is true.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Do not retransmit previously-sent data when a "receiver ready" s-frame
with the "final" flag is received during a move.
The ERTM state machines will resynchronize at the end of a channel
move, and the state machine needs to avoid state changes during a
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When operating over BR/EDR, ERTM accounts for the maximum over-the-air
packet size when setting the PDU size. AMP controllers do not use the
same over-the-air packets, so the PDU size should only be based on the
HCI MTU of the AMP controller.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The L2CAP spec recommends specific retransmit and monitor timeouts for
ERTM channels that are on AMP controllers. These timeouts are
calculated from the AMP controller's best effort flush timeout.
BR/EDR controllers use the default retransmit and monitor timeouts.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Outgoing ERTM data is queued during a channel move. The ERTM state
machine is partially reset at the start of a move, and must be
resynchronized with the remote state machine at the end of the move.
Data is not sent so that there are no state transitions between the
partial reset and the resync.
Streaming mode frames are dropped during a move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
AMP controllers expect to transmit only "complete" ACL frames. These
frames have both the "start" and "cont" bits set. AMP does not allow
fragmented ACLs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Several different actions may be taken when an AMP physical link
becomes available. A channel being created on an AMP controller must
continue the connection process. A channel being moved needs to
either send a move request or a move response. A failed physical link
will revert to using a BR/EDR controller if possible.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move confirm response concludes the channel move command sequence.
Receipt of this command indicates that data may begin to flow again.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The logical link confirm callback is executed when the AMP controller
completes its logical link setup. During a channel move, a newly
formed logical link allows a move responder to send a move channel
response. A move initiator will send a move channel confirm. A
failed logical link will end the channel move and send an appropriate
response or confirm command indicating a failure.
If the channel is being created on an AMP controller, L2CAP
configuration is completed after the logical link is set up.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The move response command includes a result code indicating
"pending", "success", or "failure" status. A pending result is
received when the remote address is still setting up a physical link,
and will be followed by success or failure. On success, logical link
setup will proceed. On failure, the move is stopped. The receiver of
a move channel response must always follow up by sending a move
channel confirm command.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
On an AMP controller, hci_chan maps to a logical link. When a channel
is being moved, the logical link may or may not be connected already.
The hci_chan->state is used to determine the existance of a useable
logical link so the link can be either used or requested.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko