This converts arm to the generic pci_set_dma_mask and
pci_set_consistent_dma_mask (removes HAVE_ARCH_PCI_SET_DMA_MASK for
dmabounce).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Looked-over-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.
The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Because original macro can only judge whether current CPU is pxa93x,
rename the macro to correct name.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This should be eventually moved to somewhere closer to the U2D driver,
but is kept here atm so it's easier for USB configuration code to work.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since the same nand controller is shared between ARCH_PXA and ARCH_MMP. Move
the pxa3xx_nand.h from mach directory to plat directoy.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This allows to select either RGB565 (transparency 0) or RGBT555
(transparency 1) from the mode info
Signed-off-by: Pieter Grimmerink <p.grimmerink@inepro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit d2c3706842 ([ARM] pxa:
initialize default interrupt priority and use ICHP for IRQ handling)
broke ISA interrupt support on pxa27x/3xx.
In such a case, PXA_IRQ(0) != 0, and the IRQ number computed from
ICHP must be offset by PXA_IRQ(0).
Tested on an Arcom Zeus (pxa270), with both CONFIG_PXA_HAVE_ISA_IRQS
enabled and disabled.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Tested-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
Add ID 99 for PXA3xx frame buffers and report it in the pxa frame buffer
conditionally, depending on a new flag in struct pxafb_mach_info.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: Dennis Oliver Kropp <dok@directfb.org>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* topic/asoc: (226 commits)
ASoC: au1x: PSC-AC97 bugfixes
ASoC: Fix WM835x Out4 capture enumeration
ASoC: Remove unuused hw_read_t
ASoC: fix pxa2xx-ac97.c breakage
ASoC: Fully specify DC servo bits to update in wm_hubs
ASoC: Debugged improper setting of PLL fields in WM8580 driver
ASoC: new board driver to connect bfin-5xx with ad1836 codec
ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
ASoC: davinci: i2c device creation moved into board files
ASoC: Don't reconfigure WM8350 FLL if not needed
ASoC: Fix s3c-i2s-v2 build
ASoC: Make platform data optional for TLV320AIC3x
ASoC: Add S3C24xx dependencies for Simtec machines
ASoC: SDP3430: Fix TWL GPIO6 pin mux request
ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
OMAP: McBSP: Use textual values in DMA operating mode sysfs files
ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
ASoC: Select core DMA when building for S3C64xx
...
and convert PXA-based devices to gpio_pwdown where possible.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
So, again against latest pxa-linux-2.6/devel, with the following
changes:
* Move to __raw_readl/__raw_writel for FPGA/CPLD register access
* Change Toppoly LCD config to be selectable at run time rather than
compile time.
* Remove currently unused irq device suspend/resume functions.
* Strip out unnecessary/duplicated #includes.
* Some code style cleanups.
Balloon3 (http://balloonboard.org/) base machine support
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for Palm Tungsten|C handheld.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for NAND chip found in PalmTX handheld. Support
is implemented through the gen_nand driver.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NAND feature will be enabled when the appropriate config option is set.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The MMC block needs 3 external datas to work :
- is the MMC card put in "read-only mode" ?
- is a MMC card inserted or removed ?
- enable power towards the MMC card
Several platforms provide these controls through
gpios. Expand the platform_data to request and use these
gpios is set up by board code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Pierre.Ossman <pierre@ossman.eu>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add priority registers and new registers of pxa935.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA93x/950 has additional 64 GPIOs, each is a secondary interrupt
source for IRQ_GPIO_2_x, extend PXA_GPIO_IRQ_{BASE,NUM}.
PXA93x/950 specific IRQ definitions are added as well.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for passing platform data to ac97 bus devices
from PXA2xx-AC97 driver..
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Attepmpt to configure ULPI pins gives the following compile error:
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
make[1]: *** [arch/arm/mach-pxa] Error 2
make: *** [sub-make] Error 2
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
For suspend/resume to work, spitz needs pxa_pm_suspend/resume to be
called. Otherwise PSPR is not set properly, and system will die during
resume.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
As pxa now is the only user of sharpsl_pm we can drop several startup
functions into generic code thus dropping several global functions.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
collie_pm was the only non-PXA user of sharpsl_pm. Now as it's gone we
can merge code into one single file to allow further cleanup.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA processors have several low-power modes. Currently kernel supports
only one of these modes for PM_SUSPEND_MEM.
This patch adds ability to set desired suspend mode for PXA27x based
machines.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The default value is 16 IRQs. Zylonite needs 32, ASIC3 based boards need 70.
My problem is still that due to the way IRQ_GPIO is hardcoded, ASIC3 based boards
need 70 IRQs starting at IRQ_BOARD_START. If I define ASIC3 IRQs similar to LoCoMo
or SA1111, things break as soon as something selects PXA_HAVE_BOARD_IRQS.
Increasing the default number of board IRQs to 70 instead doesn't seem very nice.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Support for Palm LifeDrive's internal harddrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I want to reuse tosa/spitz gpio_reset code, but my board needs the reset
gpio to be driven high during normal operation.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Currently there are two possible platform datas for the PXA AC97 driver:
one supported by the generic AC97 driver only which provides callbacks
to allow board-specific configuration at stream startup and teardown,
and another for pxa2xx-ac97-lib which allows configuration of the reset
GPIO for PXA2xx CPUs.
Obviously this won't actually work when using the generic AC97 driver
since the drivers will attempt to parse the platform data in both
formats. Fix this by merging the two structures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Even they are empty inline functions, the compiler still complains
about the missing variable names.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Daniel Mack <daniel@caiaq.de>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5446/1: ohci-at91: Limit vbus_pin assignment to the size of the array
[ARM] 5445/1: AT91: Remove flexible array from USBH platform data
[ARM] 5447/1: Add SZ_32K
[ARM] omap: fix omap1 clock usecount decrement bug
[ARM] pxa: register AC97 controller devices
[ARM] pxa/csb701: do not register devices on non-csb726 boads
[ARM] pxa/colibri: get rid of set_irq_type()
[ARM] pxa/colibri: provide MAC address from ATAG_SERIAL
[ARM] pxa/cm-x2xx: fix ucb1400 not being registered
[ARM] pxa: Add support for suspend on PalmTX, T5 and LD
[ARM] pxa: PalmTE2 support for battery, UDC, IrDA and backlight
[ARM] pxa: Palm Tungsten E2 basic support
[ARM] pxa/em-x270: add libertas device registration
[ARM] pxa/magician: Enable bq24022 regulator for gpio_vbus and pda_power
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
In commit 47cb035560, the ax88796 driver
learned to take IRQ flags from platform_device definition. Use that here
to get rid of the set_irq_type() hack.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In 67fca028f1, the ax88796 ethernet driver
learned a way to let the platform data hand in the MAC address. Use it
here as the original Colibri bootloader passes in a MAC address via
ATAG_SERIAL.
Reported-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This contains support for keypad, MMC, AC97, LCD and backlight.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
With this patch, the bq24022 battery charger is controlled by the USB
gadget framework (via gpio_vbus) when connected to USB.
To compile, this patch depends on the "regulator: Allow init data to be
supplied for bq24022" patch (queued for next in the regulator tree) to
add the init_data field to struct bq24022_mach_info.
It also depends on the "add optional OTG transceiver and voltage
regulator support to pda_power" patch (queued for next in the power
supply tree) to enable charging when connected to the AC charger.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. add common GPIO handling code into [arch/arm/plat-pxa]
2. common code in <mach/gpio.h> moved into <plat/gpio.h>, new processors
should implement its own <mach/gpio.h>, provide the following required
definitions and '#include <plat/gpio.h>' in the end:
- GPIO_REGS_VIRT for mapped virtual address of the GPIO registers'
physical I/O memory
- macros of GPLR(), GPSR(), GPDR() for constant optimization for
functions gpio_{set,get}_value() (so that bit-bang code can still
have tolerable performance)
- NR_BUILTIN_GPIO for the number of onchip GPIO
- definitions of __gpio_is_inverted() and __gpio_is_occupied(), they
can be either macros or inlined functions
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. introduce folder of 'arch/arm/plat-pxa' for common code across different
PXA processor families
2. initially moved DMA code into plat-pxa
3. common code in <mach/dma.h> moved into <plat/dma.h>, new processors
should implement its own <mach/dma.h>, provide the following required
definitions and '#include <plat/dma.h>' in the end:
- DMAC_REGS_VIRT for mapped virtual address of the DMA registers'
physical I/O memory
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This adds LCD functions for Colibri PXA300 and Colibri PXA320 and
configures a LQ043T3DX02 panel.
Original-code-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
- Move common function for all Colibri PXA3xx boards to the newly
added colibri-pxa3xx.c
- Drop some unnecessary defines from colibri.h
- Make Kconfig reflect the fact that code for colibri 300 module does
also work for the 310 model
- Give up on the huge pin config table which was messed up with lots of
#ifdefs and switch over to locally defined tables for configured
functions
Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch add basic support for Toradex' Colibri PXA300 module.
Ethernet is enabled conditionally, depdending on CONFIG_AX88796.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Namespace cleanup: rename colibri.c to colibri-pxa270.c and change
some names in colibri.h.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The typo was originally fixed by Mike Rapoport and missed. And is
later reported by Matthias Meier.
Signed-off-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The remaining registers are separated into:
- <mach/regs-ost.h>
- <mach/regs-rtc.h>
- <mach/regs-intc.h>
and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:
1. include the specific <mach/regs-*.h> with care (if that's absolutely
necessary)
2. define the registers in the driver, make cleanly defined API to expose
the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This isn't perfect but at least solves the problem of pm.c's dependency
on register definitions in <mach/lubbock.h>, which doesn't make much
sense.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().
By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.
As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.
GPLR GPDR GPSR GPCR GRER GFER GEDR
BANK 0 - 0x0000 0x000C 0x0018 0x0024 0x0030 0x003C 0x0048
BANK 1 - 0x0004 0x0010 0x001C 0x0028 0x0034 0x0040 0x004C
BANK 2 - 0x0008 0x0014 0x0020 0x002C 0x0038 0x0044 0x0050
BANK 3 - 0x0100 0x010C 0x0118 0x0124 0x0130 0x013C 0x0148
BANK 4 - 0x0104 0x0110 0x011C 0x0128 0x0134 0x0140 0x014C
BANK 5 - 0x0108 0x0114 0x0120 0x012C 0x0138 0x0144 0x0150
NOTE:
BANK 3 is only available on PXA27x and later processors.
BANK 4 and 5 are only available on PXA935
1. introduce GPIO_BANK(n) for the offset base of each bank
2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
setings, and saved register values as well, and is dynamically
allocated due to possible bank number ranging from 3 to 6
3. all accesses to GPIO registers are made through 'regbase' within
'pxa_gpio_chip', and register offset
4. introduce several inline functions to simplify the code a bit
5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is part of the work making gpio.c generic enough, the changes
include:
1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)
2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
number for the muxed GPIOs
3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:
<mach/pxa25x.h> - for pxa25x based platforms
<mach/pxa27x.h> - for pxa27x based platforms
<mach/pxa300.h> - for pxa300 based platforms
<mach/pxa320.h> - for pxa320 based platforms
<mach/pxa930.h> - for pxa930 based platforms
NOTE:
1. one header one board file, they are not compatible (i.e. they have
conflicting definitions which won't compile if included together).
2. Unless strictly necessary, the following header files are considered
to be SoC files use _only_, and is not recommended to be included in
board code:
<mach/hardware.h>
<mach/pxa-regs.h>
<mach/pxa2xx-regs.h>
<mach/pxa3xx-regs.h>
<mach/mfp.h>
<mach/mfp-pxa2xx.h>
<mach/mfp-pxa25x.h>
<mach/mfp-pxa27x.h>
<mach/mfp-pxa3xx.h>
<mach/mfp-pxa300.h>
<mach/mfp-pxa320.h>
<mach/mfp-pxa930.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add two more bitfields for the PSP register. As they seem to exist
for PXA3xx only, define them conditionally.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A bit in PXA's SSCR0 register was erroneously named ADC but its name is
in fact ACS (audio clock select).
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the AM300 platform driver which uses the
E-Ink broadsheetfb display driver.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch depends on otg_transceiver support in pxa27x_udc
(which is queued via linux-usb) to work.
It compiles also without it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch provides suupport for the wm9705 AC97 codec on the Toshiba e740.
Note:
The e740 has a hard headphone switch that turns the speaker off and is not
software detectable or controlable. Also both headphone and speaker amps
share a common output enable.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The only exclusive definitions are SSCR0_SCR and SSCR0_SerClkDiv(), loosen
that exclusive #ifdef .. #else .. #endif to allow other definitions to be
visible when slected multiple processors. This helps to pass the building
of pxa-ssp.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch adds support for the wm9712 ac97 codec as used in the Toshiba e800
PDA. It includes support for powering up / down the external headphone and
speaker amplifiers on this machine.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the wm9705 ac97 codec as used in the Toshiba e750
PDA. It includes support for powering up / down the external headphone and
speaker amplifiers on this machine.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
PXA27x and later processors support overlay1 and overlay2 on-top of the
base framebuffer (although under-neath the base is also possible). They
support palette and no-palette RGB formats, as well as YUV formats (only
available on overlay2). These overlays have dedicated DMA channels and
behave in a similar way as a framebuffer.
This heavily simplified and re-structured work is based on the original
pxafb_overlay.c (which is pending for mainline merge for a long time).
The major problems with this pxafb_overlay.c are (if you are interested
in the history):
1. heavily redundant (the control logics for overlay1 and overlay2 are
actually identical except for some small operations, which are now
abstracted into a 'pxafb_layer_ops' structure)
2. a lot of useless and un-tested code (two workarounds which are now
fixed on mature silicons)
3. cursorfb is actually useless, hardware cursor should not be used
this way, and the code was actually un-tested for a long time.
The code in this patch should be self-explanatory, I tried to add minimum
comments. As said, this is basically simplified, there are several things
still on the pending list:
1. palette mode is un-supported and un-tested (although re-using the
palette code of the base framebuffer is actually very easy now with
previous clean-up patches)
2. fb_pan_display for overlay(s) is un-supported
3. the base framebuffer can actually be abstracted by 'pxafb_layer' as
well, which will help further re-use of the code and keep a better
and consistent structure. (This is the reason I named it 'pxafb_layer'
instead of 'pxafb_overlay' or something alike)
See Documentation/fb/pxafb.txt for additional usage information.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
1. introduce var_to_depth() to calculate the color depth including the
transparency bit
2. the conversion from 'fb_var_screeninfo' to LCCR3 BPP bits can be re-
used by overlays (in OVLxC1), thus an individual pxafb_var_to_bpp()
has been separated out.
3. pxafb_setmode() should really set the color bitfields correctly at
begining, introduce a pxafb_set_pixfmt() for this
4. allow user apps to specify color formats within fb_var_screeninfo,
and checking of this in pxafb_check_var() has been simplified as
below:
a) pxafb_var_to_bpp() should pass - which means a basically correct
bits_per_pixel and color depth setting
b) the RGBT bitfields are then forced into supported values by
pxafb_set_pixfmt()
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
Add the palette format support for LCCR4_PAL_FOR_3, and fix the
issue of LCCR4 being never assigned.
Also remove the useless pxafb_set_truecolor().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
dma branching is enabled by extending the current setup_frame_dma()
function to allow a 2nd set of frame/palette dma descriptors to be
used.
As a result, pxafb_dma_buff.dma_desc[], pxafb_dma_buff.pal_desc[]
and pxafb_info.fdadr[] are doubled.
This allows maximum re-use of the current dma setup code, although
the pxafb_info.fdadr[xx] for FBRx register values looks a bit odd.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
The amount of video memory size is decided according to the following
order:
1. <xres> x <yres> x <bits_per_pixel> by default, which is the backward
compatible way
2. size specified in platform data
3. size specified in module parameter 'options' string or specified in
kernel boot command line (see updated Documentation/fb/pxafb.txt)
And now since the memory is allocated from system memory, the pxafb_mmap
can be removed and the default fb_mmap() should be working all right.
Also, since we now have introduced the 'struct pxafb_dma_buff' for DMA
descriptors and palettes, the allocation can be separated cleanly.
NOTE: the LCD DMA actually supports chained transfer (i.e. page-based
transfers), to simplify the logic and keep the performance (with less
TLB misses when accessing from memory mapped user space), the memory
is allocated by alloc_pages_*() to ensures it's physical contiguous.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.
Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Changes made as suggested by Eric Miao (including fix to map_io
silly mistake!).
Originally designed by Intel, now sold by Crossbow (www.xbow.com).
Very little actually on board. The patch includes sensors and
similar as found on commonly occurring daughter boards.
Some of the drivers are not in mainline as yet as they are either
part of the IIO subsystem or need a lot of work before submission.
What is the position wrt to putting them in i2c board configs etc?
Support for these boards has been maintained outside the kernel
for a long time, but now that there is a good da9030 pmic driver
available the last major hurdle no longer exists.
All comments welcomed.
The Imote2's big brother (stargate2) will follow once any problems
with this one have been cleaned up and a few bits and bobs have
been added to the da903x driver. Hopefully the cc2420 driver will
get cleaned up and submitted in the not too distant future as
well.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Some smart panel requires a delay between command sequences, while PXA
LCD controller didn't provide such one, let's emulate this by software.
A software delay marker can be inserted into the command sequence, once
pxafb_smart_queue() detects this, it flushes the previous commands and
delay for a specified number of milliseconds.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
For smart panels (LCD panel with internal framebuffer), the following
LCCR3 register bits have different meanings than the parallel one:
LCCR3_PCP - controls the L_PCLK_WR polarity
LCCR3_HSP - controls the L_LCLK_A0 polarity
LCCR3_VSP - controls the L_FCLK_RD polarity
To keep minimum change to the original parallel timing, the .lcd_conn
flags and 'pxafb_mode_info.sync' are re-used to reflect this:
LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP
sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP}
Signed-off-by: Eric Miao <eric.miao@marvell.com>
FUJITA Tomonori