Assumption so far was that PMBus devices would support TEMP2 and TEMP3 registers
only on page 0, and that only the TEMP1 register would be used/supported
on other pages.
Turns out that is not correct. UCD92xx devices support TEMP1 and TEMP2 on
page 0, and TEMP2 on other pages. So it is necessary to change the core code
such that it does not make a page based assumptions about temperature register
support.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
So far, it seemed like fans would either all be in page 0, or that
there would be one page per fan.
Turns out this was a wrong assumption. There is at least one PMBus
fan controller which supports three pages with four fans each.
Update code to handle this situation.
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
Some PMBus chips do not support the VOUT_MODE register. To make matters worse,
such chips may not return an error when reading the register either, but instead
return 0xff.
Check if the register exists using pmbus_check_byte_register() before reading
its value. In addition, validate the returned value and ignore it if it is 0xff
(which is invalid).
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
EMC6D103S is similar to EMC6D103, only it does not support registers 62[5:7],
6D[0:7], and 6E[0:7]. Register respective sysfs attributes and update affected
registers for all other chips only.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, the driver updates temp_auto_hyst and temp_auto_off if temp_auto_min changes.
This may cause problems if temp_auto_off was not configured before configuring
temp_auto_min, because one of the variables used (off_desired) is not initialized
in this case.
To simplify the code, and for consistency with other drivers, no longer update the delta
between "min" and "off" until the user sets the "off" value again.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADT7463 and ADT7468 optionally support VID5 instead of the standard +12V
measurement input. Use a boolean to identify the chip configuration instead of
hardcoding it several times.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the lis3lv02d SPI driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch initializes register CONFIG3 to a reasonable default PWM frequency
of 25kHz, to prevent audible sound in fan.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
This reverts the parent commit. I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
oom_kill_process() starts with victim_points == 0. This means that
(most likely) any child has more points and can be killed erroneously.
Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm. This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.
Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leverage the commit for ARM by Will Deacon:
- 446a5a8b1e
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2015/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Frederic Weisbecker:
- f72c1a931e
perf: Factorize callchain context handling
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
- 56962b4449
perf: Generalize some arch callchain code
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
- 70791ce9ba
perf: Generalize callchain_store()
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
- c1a65932fd
perf: Drop unappropriate tests on arch callchains
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Peter Zijlstra:
- a4eaf7f146
perf: Rework the PMU methods
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
For MIPSXX, the stopped state is implemented in the way of 1.b as above.
- 33696fc0d1
perf: Per PMU disable
Changes perf_disable() into perf_pmu_disable().
- 24cd7f54a0
perf: Reduce perf_disable() usage
Since the current perf_disable() usage is only an optimization,
remove it for now. This eases the removal of the __weak
hw_perf_enable() interface.
- b0a873ebbf
perf: Register PMU implementations
Simple registration interface for struct pmu, this provides the
infrastructure for removing all the weak functions.
- 51b0fe3954
perf: Deconstify struct pmu
sed -ie 's/const struct pmu\>/struct pmu/g' `git grep -l "const struct pmu\>"`
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commit by Peter Zijlstra:
- e360adbe29
irq_work: Add generic hardirq context callbacks
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
For MIPSXX, we need to call irq_work_run() at the tail of the perf IRQ
handler as described above.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com,
Patchwork: http://patchwork.linux-mips.org/patch/2011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This error was reported by cppcheck:
arch/mips/loongson/common/machtype.c:56: error: Dangerous usage of 'str' (strncpy doesn't always 0-terminate it)
If strncpy copied MACHTYPE_LEN bytes, the destination string str
was not terminated.
The patch adds one more byte to str and makes sure that this byte is
always 0.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2053/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Under some combinations of CONFIG_*, lastpfn in page_is_ram is 'set
but not used'. Mark it as __maybe_unused to quiet the warning/error.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of arch/mips/math-emu/ieee754int.h, the COMPXSP and
COMPXDP macros are used in several places, but a couple of them leave
xs unused. The easiest thing to do is mark it as __maybe_unused to
quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of protected_restore_fp_context{,32}, the variable tmp is
really used. Its use is tricky in that we really care about the side
effects of the __put_user() calls. So we must mark tmp with
__maybe_unused to quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson builds have an ad-hoc cmdline default of "console=ttyS0,115200
root=/dev/hda1". These settings come from a vendor; I remember builds
from Lemote branch requiring a "console=tty" override in order to get a
working console.
At least on Yeeloong, they're particularly useless: there's no external
serial port, and the IDE drive is now recognised as /dev/sda.
Signed-off-by: Robert Millan <rmh@gnu.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sysmips(MIPS_FIXADE, ...) case contains an obvious copy-and-paste
error in the handling of the TIF_LOGADE flag. Fix that
Patchwork: https://patchwork.linux-mips.org/patch/1997/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was reported that GCC-4.3.3 (with CodeSourcery extensions) fails
without this.
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trace.func should be set to the recorded ip of the mcount calling site
in the __mcount_loc section to filter the function entries configured
through the tracing/set_graph_function interface, but before, this is
set to the self_ra(the return address of mcount), which has made
set_graph_function not work as expected.
This fixes it via calculating the right recorded ip in the __mcount_loc
section and assign it to trace.func.
Reported-by: Zhiping Zhong <xzhong86@163.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2017/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
This moves the comments out of ftrace_make_nop() and cleans it. At the
same time, a macro MCOUNT_OFFSET_INSNS is defined for sharing with the
next patch.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2008/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
The old prepare_ftrace_return() for MIPS is confused and have introduced
some problem. This patch cleans up the names of the arguments, variables
and related functions.
For MIPS, the 2nd argument of prepare_ftrace_return() is not really the
'selfpc' described in ftrace-design.txt but instead it is the self
return address. This did break the compatibility of the generic
interface but really reduced one unneeded calculation for to get the
current function name, the parent return address and the self return
address are enough, no need to tranform the self return address to the
self address.
But set_graph_function of function graph tracer is an exception, it does
need the 2nd argument of prepare_ftrace_return() as 'selfpc', for it
will use 'selfpc' to match user's configuration of function graph
entries, but in reality, it doesn't need the 'selfpc' but the recorded
ip address of the mcount calling site in the __mcount_loc section. So,
the 2nd argument of prepare_ftrace_return() is not important, the real
requirement is the right recorded ip address should be calculated and
assign to trace.func, this will be fixed in the next patches.
Reported-by: Zhiping Zhong <xzhong86@163.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2007/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
The old in_module() may not work in some situations(e.g. when module &
kernel are in the same address space when CONFIG_MAPPED_KERNEL=y), The
in_kernel_space() is more generic and it is also easy to be implemented
via cloning the existing core_kernel_text(), so, replace the in_module()
with in_kernel_space().
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2005/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
This simply moves the "ip-=4" statement down to the end of the do { ...
} while (...); loop, which reduces one unneeded subtration and the
subsequent memory loading and comparison.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2006/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: NFSROOT should default to "proto=udp"
nfs4: remove duplicated #include
NFSv4: nfs4_state_mark_reclaim_nograce() should be static
NFSv4: Fix the setlk error handler
NFSv4.1: Fix the handling of the SEQUENCE status bits
NFSv4/4.1: Fix nfs4_schedule_state_recovery abuses
NFSv4.1 reclaim complete must wait for completion
NFSv4: remove duplicate clientid in struct nfs_client
NFSv4.1: Retry CREATE_SESSION on NFS4ERR_DELAY
sunrpc: Propagate errors from xs_bind() through xs_create_sock()
(try3-resend) Fix nfs_compat_user_ino64 so it doesn't cause problems if bit 31 or 63 are set in fileid
nfs: fix compilation warning
nfs: add kmalloc return value check in decode_and_add_ds
SUNRPC: Remove resource leak in svc_rdma_send_error()
nfs: close NFSv4 COMMIT vs. CLOSE race
SUNRPC: Close a race in __rpc_wait_for_completion_task()
