* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits)
DaVinci: DM646x - platform changes for vpif capture and display drivers
davinci: DM355 - platform changes for vpfe capture
davinci: DM644x platform changes for vpfe capture
davinci: audio: move tlv320aic33 i2c setup into board files
DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
DaVinci: DM365: Adding entries for DM365 IRQ's
DaVinci: DM355: Adding PINMUX entries for DM355 Display
davinci: Handle pinmux conflict between mmc/sd and nor flash
davinci: Add NOR flash support for da850/omap-l138
davinci: Add NAND flash support for DA850/OMAP-L138
davinci: Add MMC/SD support for da850/omap-l138
davinci: Add platform support for da850/omap-l138 GLCD
davinci: Macro to convert GPIO signal to GPIO pin number
davinci: Audio support for DA850/OMAP-L138 EVM
davinci: Audio support for DA830 EVM
davinci: Correct the number of GPIO pins for da850/omap-l138
davinci: Configure MDIO pins for EMAC
DaVinci: DM365: Add Support for new Revision of silicon
DaVinci: DM365: Fix Compilation issue due to PINMUX entry
DaVinci: EDMA: Updating default queue handling
...
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
Add support for Dynamic Power Switching (DPS) for the RX51 board.
These scripts are still a work-in-progress. I'll keep sending patches to
update the scripts as they are optimised.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
VPIF display changes (Chaithrika)
Add platform device and resource structures. Also define a platform specific
clock setup function that can be accessed by the driver to configure the clock
and CPLD.
VPIF caputure changes (Murali)
1) Modify vpif_subdev_info to add board_info, routing information and
vpif interface configuration. Remove addr since it is part of
board_info
2) Add code to setup channel mode and input decoder path for vpif
capture driver
Also incorporated comments against version v0 of the patch series and
added a spinlock to protect writes to common registers
Tested on DM6467 on channel 0 using TVP514x. Following bootargs used
for drivers:
vpif_capture.ch0_bufsize=829440 vpif_display.ch2_bufsize=829440
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM355 platform and board setup
This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.
Tested video capture on DM355 using tvp514x
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM644x platform and board setup
This adds platform and board setup changes required to support
vpfe capture driver on DM644x
Tested video capture on DM6446 with tvp514x driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (23 commits)
at_hdmac: Rework suspend_late()/resume_early()
PM: Reset transition_started at dpm_resume_noirq
PM: Update kerneldoc comments in drivers/base/power/main.c
PM: Add convenience macro to make switching to dev_pm_ops less error-prone
hp-wmi: Switch driver to dev_pm_ops
floppy: Switch driver to dev_pm_ops
PM: Trivial fixes
PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
PM/Hibernate: Rework shrinking of memory
PM: Fix typo in label name s/Platofrm_finish/Platform_finish/
PM: Run-time PM platform device bus support
PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
Driver Core: Make PM operations a const pointer
PM: Remove platform device suspend_late()/resume_early() V2
USB: Rework musb suspend()/resume_early()
I2C: Rework i2c-s3c2410 suspend_late()/resume() V2
I2C: Rework i2c-pxa suspend_late()/resume_early()
DMA: Rework txx9dmac suspend_late()/resume_early()
...
Fix trivial conflict in drivers/base/platform.c (due to same
constification patch being merged in both sides, along with some other
PM work in the PM branch)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
This moves the primecell vendor enum definition inside vic.c
out to linux/amba/bus.h where it belongs and replace any
occurances of specific vendor ID:s with the respective enums
instead.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On OMAP platforms, some people want to declare to segment up the memory
between the kernel and a separate application such that there is a hole
in the middle of the memory as far as Linux is concerned. However,
they want to be able to mmap() the hole.
This currently causes problems, because update_mmu_cache() thinks that
there are valid struct pages for the "hole". Fix this by making
pfn_valid() slightly more expensive, by checking whether the PFN is
contained within the meminfo array.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Khasim Syed Mohammed <khasim@ti.com>
* topic/asoc: (226 commits)
ASoC: au1x: PSC-AC97 bugfixes
ASoC: Fix WM835x Out4 capture enumeration
ASoC: Remove unuused hw_read_t
ASoC: fix pxa2xx-ac97.c breakage
ASoC: Fully specify DC servo bits to update in wm_hubs
ASoC: Debugged improper setting of PLL fields in WM8580 driver
ASoC: new board driver to connect bfin-5xx with ad1836 codec
ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
ASoC: davinci: i2c device creation moved into board files
ASoC: Don't reconfigure WM8350 FLL if not needed
ASoC: Fix s3c-i2s-v2 build
ASoC: Make platform data optional for TLV320AIC3x
ASoC: Add S3C24xx dependencies for Simtec machines
ASoC: SDP3430: Fix TWL GPIO6 pin mux request
ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
OMAP: McBSP: Use textual values in DMA operating mode sysfs files
ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
ASoC: Select core DMA when building for S3C64xx
...
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add #inclusions of linux/tracehook.h to those arch files that had the tracehook
call for TIF_NOTIFY_RESUME added when support for that flag was added to that
arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch add support for the 2Big Network LaCie boards.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
sharpsl_pm.c code tries to read battery state very early during
resume, but those battery meters are connected on SPI and that's only
resumed way later.
Replace the check with simple checking of battery fatal signal, that
actually works at this stage.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
HSS usually uses external clocks, so it's not a big deal. Internal clock
is used for direct DTE-DTE connections and when the DCE doesn't provide
it's own clock.
This also depends on the oscillator frequency. Intel seems to have
calculated the clock register settings for 33.33 MHz (66.66 MHz timer
base). Their settings seem quite suboptimal both in terms of average
frequency (60 ppm is unacceptable for G.703 applications, their primary
intended usage(?)) and jitter.
Many (most?) platforms use a 33.333 MHz oscillator, a 10 ppm difference
from Intel's base.
Instead of creating static tables, I've created a procedure to program
the HSS clock register. The register consists of 3 parts (A, B, C).
The average frequency (= bit rate) is:
66.66x MHz / (A + (B + 1) / (C + 1))
The procedure aims at the closest average frequency, possibly at the
cost of increased jitter. Nobody would be able to directly drive an
unbufferred transmitter with a HSS anyway, and the frequency error is
what it really counts.
I've verified the above with an oscilloscope on IXP425. It seems IXP46x
and possibly IXP43x use a bit different clock generation algorithm - it
looks like the avg frequency is:
(on IXP465) 66.66x MHz / (A + B / (C + 1)).
Also they use much greater precomputed A and B - on IXP425 it would
simply result in more jitter, but I don't know how does it work on
IXP46x (perhaps 3 least significant bits aren't used?).
Anyway it looks that they were aiming for exactly +60 ppm or -60 ppm,
while <1 ppm is typically possible (with a synchronized clock, of
course).
The attached patch makes it possible to set almost any bit rate
(my IXP425 533 MHz quits at > 22 Mb/s if a single port is used, and the
minimum is ca. 65 Kb/s).
This is independent of MVIP (multi-E1/T1 on one HSS) mode.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board code was wrongly setting up the reset pin for AC97 on at91sam9263ek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the support of AC97 on the at91sam9263 ek board, so it would
share the code with AVR32.
Plus it removes a typo in at91sam9263_devices.c.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the default config for HP Jornada 700-series handhelds.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's suppose a highmem page is kmap'd with kmap(). A pkmap entry is
used, the page mapped to it, and the virtual cache is dirtied. Then
kunmap() is used which does virtually nothing except for decrementing a
usage count.
Then, let's suppose the _same_ page gets mapped using kmap_atomic().
It is therefore mapped onto a fixmap entry instead, which has a
different virtual address unaware of the dirty cache data for that page
sitting in the pkmap mapping.
Fortunately it is easy to know if a pkmap mapping still exists for that
page and use it directly with kmap_atomic(), thanks to kmap_high_get().
And actual testing with a printk in the added code path shows that this
condition is actually met *extremely* frequently. Seems that we've been
quite lucky that things have worked so well with highmem so far.
Cc: stable@kernel.org
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rewinding each debugfs entries to unregister if an error happens.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device code provides a mapping of omap_hwmod structures into
the platform_device system, and includes some details on external
(board-level) integration. This allows drivers to enable, idle, and
shutdown on-chip device resources, including clocks, regulators, etc.
The resources enabled and idled are dependent on the device's maximum
wakeup latency constraint (if present).
At the moment, omap_device functions are intended to be called from
platform_data function pointers. Ideally in the future these
functions will be called from either subarchitecture-specific
platform_data activate, deactivate functions, or via an custom
bus/device type for OMAP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Connect the omap_hwmod code to the kernel boot. Create some basic
interconnect and device structures for OMAP2/3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP SoCs can be considered a collection of hardware IP blocks
connected by various interconnects. The bus topology and device
integration data is somewhat more complex than platform_device can
encode. This patch creates code and structures to manage information
about OMAP on-chip devices ("hardware modules") and their integration
to the rest of the chip. Hardware module data is intended to be
generated dynamically from the TI hardware database for the OMAP4
chips and beyond, easing Linux support for new chip variants.
This code currently:
- resets and configures all hardware modules upon startup, reducing bootloader
dependencies;
- provides hooks for Linux driver model code to enable, idle, and shutdown
hardware modules (forthcoming patch);
- waits for hardware modules to leave idle once their clocks
are enabled and OCP_SYSCONFIG bits are set appropriately.
- provides a means to pass arbitrary IP block configuration data (e.g.,
FIFO size) to the device driver (via the dev_attr void pointer)
In the future this code is intended to:
- estimate interconnect bandwidth and latency characteristics to
ensure constraints are satisfied during DVFS
- provide *GRPSEL bit data to the powerdomain code
- handle pin/ball muxing for devices
- generate IO mapping information dynamically
- supply device firewall configuration data
- provide hardware module data to other on-chip coprocessor software
- allow the removal of the "disable unused clocks" code in the OMAP2/3
clock code
This patch represents a collaborative effort involving many people from TI,
Nokia, and the Linux-OMAP community.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort. This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all. This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure. The new code will use these new
functions to handle waiting for modules to enable.
Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface. Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.
Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them. Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput(). Jouni signed off on Tero's patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
omap2_init_clk_clkdm() is called as part of the chip architecture-specific
initialization code, so calling it again from the struct clk init pointer
just wastes cycles.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
All MPU-related clocks should be in the mpu_clkdm. This is needed for the
upcoming omap_hwmod patches, which needs to know the clockdomain that arm_fck
is in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The argument 'mpurate' had no effect on the MPU
frequency. This patch fixes the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
