The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU. The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.
This change enables the timer with the minimum period at the point
when the suspension is requested.
Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts. Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.
The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ notify waiters when controller stop completes (fixes 10 second stall
unloading the driver)
2/ make sure phy stop is after port and device stop
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Based on an original implementation by Ed Nadolski and Artur Wojcik
In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init(). Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations). The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().
The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful. In the case of isci we'll just re-init using a subset of the
normal driver load path.
[clean up some unused / mis-indented function definitions in host.h]
Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer. The other BC primitives have been
added to the sci_phy_event_handler()
Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
domain_device ->parent conveys the same information.
Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).
Fix up the rnc warnings to use the state name.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With the exception of the detached field, sg_mutex no longer adds any
locking. detached handling has been broken before and is still broken
and this patch does not seem to make things worse than they were to
begin with.
However, I have observed cases of tasks being blocked for >200s waiting
for sg_mutex. So the removal clearly adds value for very little cost.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sfds is protected by sg_index_lock - except for sg_open(), where it
isn't. Change that and add some documentation.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changes since v1: set_exclude now returns the new value, which gets
rid of the comma expression and the operator precedence bug. Thanks
to Douglas for spotting it.
sdp->exclude was previously protected by the BKL. The sg_mutex, which
replaced the BKL, only semi-protected it, as it was missing from
sg_release() and sg_proc_seq_show_debug(). Take an explicit spinlock
for it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
srp->done is protected by sfp->rq_list_lock everywhere, except for this
one case. Result can be that the wake-up happens before the cacheline
with the changed srp->done has arrived, so the waiter can go back to
sleep and never be woken up again.
The wait_event_interruptible() means that anyone trying to debug this
unlikely race will likely notice everything working fine again, as the
next signal will unwedge things. Evil.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
After sg_release() has been called, noone should be able to actually use
that filedescriptor anymore. So if closed ever made a difference in the
past five years or so, it would have meant a bug. Remove it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
[jejb: fix up checkpatch warnings]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Afaics the use of __wait_event_interruptible() as opposed to
wait_event_interruptible() is purely historic. So let's follow the rest
of the kernel and check the condition before prepare_to_wait() - and
also make the code a bit nicer.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The while (1) construct isn't actually a loop at all. So let's not
pretent and obfuscate the code.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
blocking is de-facto a constant and the now-removed comment wasn't all
that useful either. Without them and the resulting indentation the code
is a bit nicer to read.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dial back the aggressiveness of the controller lockup detection thread.
Currently it will declare the controller to be locked up if it goes
for 10 seconds with no interrupts and no change in the heartbeat
register. Dial back this to 30 seconds with no heartbeat change, and
also snoop the ioctl path and if a firmware flash command is detected,
dial it back further to 4 minutes until the firmware flash command
completes. The reason for this is that during the firmware flash
operation, the controller apparently doesn't update the heartbeat
register as frequently as it is supposed to, and we can get a false
positive.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use spinlocks with finer granularity in the submission and
completion paths to allow concurrent execution for multiple
reply queues. In particular, do not hold a spin lock while
submitting a request to the device, nor during most of the
interrupt handler.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Smart Arrays can support multiple reply queues onto which command
completions may be deposited. It can help performance quite a bit
to arrange for command completions to be processed on the same CPU
from which they were submitted to increase the likelihood of cache
hits.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is in order to smooth the way for upcoming changes to allow use of
multiple reply queues for command completions.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When aborting a command, the tag is supposed to be
specified as 64-bit little endian. However, some smart
arrays expect the tag of the command to be aborted to be
specified in a strange byte order. How to tell which sort
of Smart Array firmware we're dealing with is not obvious.
However, because of the way we construct our tags, the values
of any outstanding tag when specified with the "strange" byte
order will not collide with the value specified in the correct
order. That means we can safely attempt the abort both ways.
Signed-off-by: Stephen M. Cameron <stephenmcameron@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of giving up after 3 immediate retries of driver initiated
commands, back off the rate of retries and retry a bunch more times.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reviewed-by: Andi Shyti <andi.shyti@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In shared SAS configurations we might get a busy status
during driver initiated commands (e.g. during rescan for
devices). We should retry the command in such cases rather
than giving up.
Signed-off-by: Matt Bondurant <Matthew.dav.bondurant@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MSI/MSI-X interrupts can't race the DMA completion they are communicating
so no need to read from controller to flush the DMA to the host if
MSI or MSI-X interrupts are being used.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Default behavior for any CHECK CONDITION excepting a few special cases is to
print out certain parts of the sense buffer and the CDB. Default behavior
should be to print nothing and let the upper layers or applications decide what
to do about these. The same information is already available by setting the
appropriate bits of the scsi_logging_level kernel parameter or via
/proc/sys/dev/scsi/logging_level.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pci_disable_device() disables the bus master bit and pci_enable_device does
not re-enable it. It needs to be enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There was code to skip "disabled" devices which was intended to
skip devices disabled in the BIOS, but it really just checks to
see if the device can write to host memory, which this is disabled
by pci_disable_device on driver unload, so this check has the effect
of preventing subsequent load of the driver. And devices disabled in
the BIOS don't show up at all anyway, so this check never made any
sense to begin with, and should be removed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As Jenx Axboe explained to me: "In earlier times (2.6.18 and pre, iirc), Linux
disabled IO and mem bars on pci_disable_device(). Now in newer kernel it does
not. And in the newer kernels you run into problems if you DON'T disable the
device on exit, since when it later loads the device is already in the enabled
state - and pci_enable_device() then does nothing. This typically screws
MSI/MSI-X." This is what the big scary comment that says pci_disable_device
does "something nasty" to smart arrays was evidently referring to.
If pci_disable_device is not called on driver rmmod, subsequently insmod'ing
the driver may in result in some cases fail to be able to receive interrupts,
esp. if other drivers are loaded between unloading and loading hpsa.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check the domain validation flag on the given device before referencing
scsi_device instance, otherwise if the flag is already set we return without
decrementing the reference count.
Signed-off-by: Mike Maslenkin <mihailm@parallels.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Old version: 2.7.0.3
New version: 2.7.2.2
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This will set the target can_queue limit to the number of preallocated
session tasks set during creation.
"Could not send nopout" messages were observed without this when the
iSCSI connection experiences dropped frames under heavy I/O stress.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a followup to a patch provided by Jack Wang on September 21 2011.
After increasing the CAN_QUEUE to 510 in pm8001 we discovered some performance
degredation from time to time. We needed to increase the MPI queue to
compensate and ensure we never hit that limit. We also needed to double
the margin to support event and administrivial commands that take from
the pool resulting in an occasional largely unproductive command completion
with soft error to the caller when the command pool is overloaded temporarily.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
UTP Transfer request list base registers UTRLBA and UTRLBAU
must be assigned, lower-32 and upper-32 bits of UTRLD list
physical base addresses respectively.
Currently UTRLBAU is being assigned lower-32 bits of UTRLD
physical base address. This will cause an issue with
controllers that can support 64-bit addressing.
This patch correctly assigns upper-32 bits of UTRLD physical
base address to UTRLBAU.
Reported-by: Rene De Jong <rene.dejong@arm.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Reviewed-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We moved the locking in dd060e74fb "[SCSI] fcoe: remove frame dropping
code from fcoe_percpu_clean" but this unlock was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC-BB-6 v1.04 7.9.8.14 N_Port_ID Beacon:
"A N_Port_ID Beacon is multicast and uses the VN_Port MAC address as source
address."
Currently, libfcoe is using ENode MAC, this seems ok and functionality wise
not a problem in my back to back testing setup, however, just fix this to
make libfcoe VN2VN support more spec compliant.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The rtnl_mutex was held to protect calls to dev_uc_add
and dev_uc_del. Holding rtnl is not required as those
functions make use of the netif_addr_lock* API to
protect the MAC changing.
This change fixes the following regression by removing
the rtnl usage when fcoe_update_src_mac is called.
https://bugzilla.kernel.org/show_bug.cgi?id=42918
the existing dependency chain (in reverse order) is:
-> #1 (&fip->ctlr_mutex){+.+...}:
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<f8970c32>] fcoe_ctlr_link_up+0x22/0x180 [libfcoe]
[<f894620e>] fcoe_create+0x47e/0x6e0 [fcoe]
[<f8973dd3>] fcoe_transport_create+0x143/0x250 [libfcoe]
[<c10527e0>] param_attr_store+0x30/0x60
[<c1052696>] module_attr_store+0x26/0x40
[<c11a201e>] sysfs_write_file+0xae/0x100
[<c11449df>] vfs_write+0x8f/0x160
[<c1144cbd>] sys_write+0x3d/0x70
[<c147a0c4>] syscall_call+0x7/0xb
-> #0 (rtnl_mutex){+.+.+.}:
[<c109164b>] __lock_acquire+0x140b/0x1720
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<c13a10c4>] rtnl_lock+0x14/0x20
[<f89445ac>] fcoe_update_src_mac+0x2c/0xb0 [fcoe]
[<f8971712>] fcoe_ctlr_timer_work+0x712/0xb60 [libfcoe]
[<c104fb69>] process_one_work+0x179/0x5d0
[<c10502f1>] worker_thread+0x121/0x2d0
[<c10550ed>] kthread+0x7d/0x90
[<c1481a82>] kernel_thread_helper+0x6/0x10
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
*** DEADLOCK ***
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fcoe controller has back references, therefore defer
releasing master lport which gets freed along scsi_host_put
and then free it once fcoe interface is fully cleaned.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove lport from net device and then do synchronize net device to flush
inflight rx frames for the lport before doing fcoe_percpu_clean.
In case of master lport, remove all rx packet handlers completely and
then only do fcoe_percpu_clean. This required splitting fcoe_interface_cleanup
to do remove part separately and for that added func fcoe_interface_remove
and then call it from fcoe_if_destory before doing fcoe_percpu_clean.
However if fcoe_interface_remove() is already called then
don't call again from fcoe_interface_cleanup() to preserve its
existing flows.
This patch along with Neil's other patch to avoid soft irq context
on ingress will avoid passing up frames on disabled lport as
discussed in this mail thread:-
http://lists.open-fcoe.org/pipermail/devel/2012-February/011947.html
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While interpreting the result of UTP task completion status,
by using boolean &&, the evaluation would fail when the
UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED was received.
Either UPIU_TASK_MANAGEMENT_FUNC_COMPL or
UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED should be
considered as a success result.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When scsi_add_host fails the scsi_host_put should be called.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a rport is added back or the role is changed the fc class
will queue a scan and then call scsi_target_unblock. The problem
with this is if the devices are in the SDEV_OFFLINE state and
the scan is run before the scsi_target_unblock, then the scan
will see LUN0 as offline and the scan will fail. This patch moves
the unblock call to before the scan, so we know the device state
will be set correctly when the scan is run.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is a memory leak in the st driver when sending large enough reads or
writes using st's direct I/O path. As part of mapping the application's
memory, a buffer to hold page pointers is allocated and the count of mapped
pages is stored in field do_dio. A non-zero do_dio marks that direct I/O is
in use.
But do_dio is only 1 byte in size. Mapping 256 4k pages overflows
do_dio and causes it to be set to 0, like direct I/O option was not
used. When the I/O completes, the buffer to hold the page pointers is
not freed, and the page counts of the mapped pages are not reduced.
Every I/O of this size then leaks memory.
The size of do_dio needs to be increased to prevent it wrapping around.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix a use-after-free in the TMF path, where cmd may have been already
freed by virtscsi_complete_free when wait_for_completion restarts
executing virtscsi_tmf. Technically a race, but in practice the command
will always be freed long before the completion waiter is awoken.
The fix is to make callers specifying a completion responsible for
freeing the command in all cases.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 6f381fa344
Author: Lin Ming <ming.m.lin@intel.com>
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
Caused a regression where we oops in every legacy mode SCSI host driver
because they supply a NULL pointer to scsi_add_host(). Fix this by checking
for the NULL in scsi_add_host_with_dma() and changing the DMA device to being
the platform_bus in that case (which replicates the original behaviour).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
release_firmware() checks for NULL pointers internally so checking
before calling the function is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
release_firmware() checks for NULL pointers internally, so checking
before calling the function is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Made changes to have the same logging level for Logical port
online and offline events, to display these events in pairs.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make changes to remove unsupported model numbers from the sysfs
model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to avoid queuing the vport delete work to IM driver
work queue in the bfa_fcb_lport_delete() - since at this stage we
are not completely done with using the vport structure as we are
still waiting for the LOGO response from the fw in online state or
just doing some cleanup. Since queuing up the vport delete work at
this stage will result in the FC transport layer to clean up the vport
before we get the response from firmware.
Made changes to queue the port delete work to the IM driver work queue -
from the bfa_fcs_vport_free() function since at this state we are done
with using the vport data structure and the FCS state machine is completely
cleaned up.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hyper-V cannot process some commands like ATA_12 and ATA_16. It also returns a
very generic error when this happens (SRB_STATUS_ERROR). Most of the time we
treat SRB_STATUS_ERROR as DID_TARGET_FAILURE which causes error handler retry,
but in the case of pass through commands, they'll never succeed (and the error
handler will offline the device), so put a discriminating block in the command
completion routing and send the SRB_STATUS_ERROR upwards with DID_PASSTHROUGH
for commands we know should not be retried.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement ISCSI_HOST_PARAM_PORT_STATE and ISCSI_HOST_PARAM_PORT_SPEED
to get the Adapter port state and port name
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to set/ delete static IP and enable /disable
DHCP.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement the ISCSI_HOST_PARAM_INITIATOR_NAME for .get_host_param
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The async handle corresponding to unknown Opcode was not freed
earlier. This code does the fix for that.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For each ASYNC PDU received there is an HDR and DATA handle for it.
There will be only 1 HDR ASYNC Handle, but DATA Handle can be more
than 1 for each ASYNC PDU received. Checking if the ASYNC Handle
correspongs to HDR or DATA while returning the Handle to the free list.
hwi_free_async_msg just return the handles to the free list. No return
values are needed so changing the return type to void.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change MODULE_AUTHOR, driver name and other external print strings from
Serverengines to Emulex.
Signed-off-by: Minh Tran <MinhDuc.Tran@Emulex.Com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of MCC_Q creation failed, the MCCQ info memory is freed
from be_mcc_queues_destroy and be_mcc_queues_create. This caused
kernel to panic because of double free.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The WRB and SGL Handle allocated for Login task were not freed
back to the pool after the login process was done. This code
releases the WRB and SGL Handle after the login process.
v2:
- Fix up locking so bh calls are not done when not needed.
- Make beiscsi_cleanup_task static.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
[various fixes]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removing code duplication during the WRB_Handle and WRB
initialization.
Added memory allocation failure handling code during WRB
initialization.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The buffer length passed for processing the ASYNC PDU
was not proper.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set the ASYNC PDU Handle pBuffer for Data ring with the VA/PA
of the allocated memory for it.
To get the correct ASYNC PDY Handle iterate the list and compare
the PA set during initialization with the passed PHY Address.
The buffer_size and num_enteries are common for HDR and Data ring
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.
This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check_signature to find a signature in the mmio address.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch 116046127d "[SCSI] aacraid: Added
Sync.mode to support series 7/8/9 controllers" removed an iounmap call from
aac_src_ioremap. Before that, the iounmap has been called twice with the same
value (dev->base and dev->regs.src.bar0) and the iounmap complained about it
(iounmap: bad address ...).
The proper solution is a change the paremeter from bar0 to bar1.
Fix this by adding a an iounmap(dev->regs.src.bar1) call.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Achim Leubner <achim_leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch optimizes the set target port group(STPG) command. During our
testing, we found that it is not optimal to send stpg command every time
the path group switch happens. This patch uses PREF (preferred target port)
bit with combination of flags passed by multipath user level tool to
optimize this behaviour. If PREF bit is set then it issues a STPG command,
otherwise it will let implicit transfer take place.
By default there is no change in the behaviour. User tool needs to pass the
parameter to make this change take effect. Patch has been tested on NetApp
E series storage.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
PREF bit indicates preferred target port group for accessing a logical
unit. This bit is used to optimize the STPG command handling.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Handler expects only one parameter to set the flag ALUA_OPTIMIZE_STPG.
This flag is used to optimize the STPG behaviour. There is no change in
behaviour by default.
For example, to set the flag pass the following parameters from multipath.conf
hardware_handler "2 alua 1"
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset. The problem in _base_get_ioc_facts is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.
Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Following the host reset, the firmware discovery is reassigning another hard
drive in the topology to the same device handle as that device is getting hot
removed. Until the driver device removal routine is called, there will be two
hard drive with the matching device handle in the internal device link
list. In the device removal routine, a separate function which moves the
device from BLOCKED into OFFLINE state. Since this routine is passed with the
device handle passed as input parameter, the routine will be traversing the
internal device link list searching for matching device handle. This results
in two devices with matching device handle, therefore both devices goes
OFFLINE.
To fix this issue,the input parameter is changed from device handle to SAS
address, therefore only the device that is hot unplugged will be placed in
OFFLINE state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The phy_identifier inside the routine _transport_set_identify()
is set to sas_device_page_zero->PhyNum. This returns the
phy number of the parent device this device is linked to.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The port number is changing after disabling/enabling phys using the SysFS
interface This is because the firmware behavour changed where it would read
the the port number then set it to some different value even though Auto Port
Config is turned on. With this change of behavour in FW, it is possible that
the expanders are moved from one port to another after disabling /enabling
phys. This is occuring because the port number in sas iounit page 1 is not
matching up to the current port in page 0. In order to fix this the driver is
modified to read the current port number from sas iounit page 0 instead of
page 1. Also copy the port and phy flags over from page 0 to page 1.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix several endian issues found by runing sparse.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Modified the source code as per the findings reported by the source
code analysis tool. Source code for the following functionalities
has been touched. None of the driver functionalities has changed.
- SMP Passthrough IOCTL
- Debug messages for MPT Replies (i.e. bit 9 of Logging Level)
- Task Management using sysfs
- Device removal, i.e. when a target device (including any PD within a volume)
is removed, and Volume Deletion.
- Trace Buffer
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.
Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list. Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter. This is a bitmask used
to identify which devices need blocking when there is device loss. This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support for Block IO requests with multiple segments (vectors) in
the SMP handler of the SAS Transport Class. This is required by the
BSG driver. Multisegment support added for both, Request and Response.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the lock_kernel and unlock_kernel routines were removed in the
2.6.39 kernel, a global mutex was added on top of the existing mutex
which already existed. With this implementation, only one IOCTL
will be active at any time no matter how many ever controllers
are present. This causes poor performance.
Removed the global mutex so that the driver can work with the existing
semaphore that was already part of the existing code.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changeset in MPI headers:
1) Bumped MPI2_HEADER_VERSION_UNIT
2) Added 4K sectors supported bit to CapabilitiesFlags field of IOC Page 6.
3) Added UEFIVersion field to BIOS Page 1 and defined additional
BiosOptions bits to control UEFI behavior.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the driver version to
v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas fixes the fastpath code decision
logic to use fpRead/WriteCapable, fpRead/WriteAcrossStripe flags
instead of the old logic. This fixes a bug where fastpath writes
could be sent to a read only LD.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas removes an incorrect comment and
optimizes the setting of HostMSIxVectors. This was found during a
code review by Tomas Henzl @ RedHat.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Data type of the 'tag' field of 'fw_flash_Update_resp' should be __le32.
Data type of 'pHeader' should be __le32. Remove 2nd cast to 'piomb'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit a692b0eec5.
Tom reports:
[ 8.741033] ------------[ cut here ]------------
[ 8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[ 8.741040] Hardware name: To Be Filled By O.E.M.
[ 8.741041] sysfs: cannot create duplicate filename
...and missing 2 out of 4 drives connected to mvsas. Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique. However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas. So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7. The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: Tom Rini <trini@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover(). The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change. When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled. So change
the code to skip the sas_address and change count updates when ata_eh is
active.
Cc: Jack Wang <jack_wang@usish.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 899fcf4 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]
...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It was documented in Documentation/m68k/kernel-options.txt and
Documentation/scsi/scsi-parameters.txt, but the implementation was
missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitzmic@googlemail.com>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.
Since commit d139b9b([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.
Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
Jeff Skirvin