Correct spelling "occured" to "occurred" in
drivers/scsi/qla2xxx/qla_mbx.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Optimized queuecommand handler's to eliminate double head-room checks.
The checks are moved inside the 1st if-loop otherwise you would end up checking twice when there is
enough head room.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Reviewed-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Replace "Inconisistent" with "Inconsistent" in drivers/scsi/qla2xxx/qla_init.c
Signed-off-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For scsi devices which use scsi bus runtime callback, runtime suspend
will call scsi_dev_type_suspend, and if the drv->suspend failed, the
device will still be in active state. But since scsi_device_quiesce is
called, the device will not be able to respond any more commands.
So add a check here to see if err occured, if so, bring the device back
to normal state with scsi_device_resume.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to set the fc_host sysfs entries supported_speeds,
supported_classes etc., during the vport creation from the
FC transport template.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the task management IO times out, or a flush operation is performed while
task management IO is pending, driver is not cleaning up the IO. This patch
cleans up the IO for the above cases.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When IO abort times out during eh_abort or a flush operation is performed while
abort is pending, the driver is not cleaning up the IO and thus not reducing
the IO reference count. With this change, as part of explicit logout, the IO is
cleaned up.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 907c07d451 added more cases to do FLOGI
retry on receiving bad response. Remove the code that drops the packet and
allow the stack to handle bad FLOGI response.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPuiSaAAoJEDeqqVYsXL0MJ8wH/2QYwxCtTzwgBE4DSUrZ/mnO
ygiiausG7gNY845hAmXhoEqhYBe1GA/fvfSXOdurAPrFmfu2HvvPEyKmu3soWxLM
rrXP7JNRjHOSz+GIktZECg6K9iobldl0zCxdn515ATnBEOZVom5v+uBE13sfg5uP
iOS73JF7h2VRcAYuw8jsVTdc/rnH2nG4TsbW2B+Hp3Ti1pFSnyHbbNuE2FJ9bEX4
gTBtsYYRZPWl24WuhmmS6LHyGqL+rcU/wKj4+rAdNQwsh+MBgcMDhGQ1UWg/3OGN
N8wur7AEQnyvsYdufjFNmHBux4TcdCVZISsWYb3frctJ5XVtYViMjlbmMMy1T7s=
=rxQP
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI misc update from James Bottomley:
"The patch contains the usual assortment of driver updates (be2iscsi,
bfa, bnx2i, fcoe, hpsa, isci, lpfc, megaraid, mpt2sas, pm8001, sg)
plus an assortment of other changes and fixes. Also new is the fact
that the isci update is delivered as a git merge (with signed tag)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (158 commits)
isci: End the RNC resumption wait when the RNC is destroyed.
isci: Fixed RNC bug that lost the suspension or resumption during destroy
isci: Fix RNC AWAIT_SUSPENSION->INVALIDATING transition.
isci: Manage the IREQ_NO_AUTO_FREE_TAG under scic_lock.
isci: Remove obviated host callback list.
isci: Check IDEV_GONE before performing abort path operations.
isci: Restore the ATAPI device RNC management code.
isci: Don't wait for an RNC suspend if it's being destroyed.
isci: Change the phy control and link reset interface for HW reasons.
isci: Added timeouts to RNC suspensions in the abort path.
isci: Add protocol indicator for TMF requests.
isci: Directly control IREQ_ABORT_PATH_ACTIVE when completing TMFs.
isci: Wait for RNC resumption before leaving the abort path.
isci: Fix RNC suspend call for SCI_RESUMING state.
isci: Manage tag releases differently when aborting tasks.
isci: Callbacks to libsas occur under scic_lock and are synchronized.
isci: When in the abort path, defeat other resume calls until done.
isci: Implement waiting for suspend in the abort path.
isci: Make sure all TCs are terminated and cleaned in LUN reset.
isci: Manage the LLHANG timer enable/disable per-device.
...
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Setup CROSS_COMPILE at the top
m68k: Correct the Atari ALLOWINT definition
m68k/video: Create <asm/vga.h>
m68k: Make sure {read,write}s[bwl]() are always defined
m68k/mm: Port OOM changes to do_page_fault()
scsi/atari: Make more functions static
scsi/atari: Revive "atascsi=" setup option
net/ariadne: Improve debug prints
m68k/atari: Change VME irq numbers from unsigned long to unsigned int
m68k/amiga: Use arch_initcall() for registering platform devices
m68k/amiga: Add error checks when registering platform devices
m68k/amiga: Mark z_dev_present() __init
m68k: Remove unused MAX_NOINT_IPL definition
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HYvO
-----END PGP SIGNATURE-----
Merge tag 'isci-for-3.5' into misc
isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes the MCA specific SCSI drivers, and the
MCA specific portions of code in dual role ISA/MCA drivers.
Also, the MCA specific SCSI documentation is removed.
Cc: James Bottomley <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
While the RNC is suspended for I/O cleanup, the remote device can be
stopped and the RNC setup for destruction. These changes accomodate that
case in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fix corrects the saving of resume parameters when the destruction
of the RNC has already been directed, and makes sure not to overwrite
the RNC destruction callbacks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RNC state machine would incorrectly transition from
SCI_RNC_AWAIT_SUSPENSION directly to SCI_RNC_INVALIDATING when a destruct
request was made. This would skip the increment of the suspension count
and the abort of pending TCs (although the invalidating state would at
least cleanup outstanding TCs).
Instead, the RNC will transition to SCI_RNC_SUSPENDED and then start the
destruction process.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since there is a possibilty of a timeout waiting for the RNC suspension,
handle the exit case from the task termination under scic_lock, and leave
the tag allocated if the termination timed-out.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since the callbacks to libsas now occur under scic_lock, there is no
longer any reason to save the completed requests in a separate list
for completion to libsas.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the link fail path, set IDEV_GONE for every device on the domain
when the last link in the port fails.
In the abort path functions like isci_reset_device, make sure that
there has not already been a detected domain failure with the device
by checking IDEV_GONE, before performing any kind of hard reset, SMP
phy control, or TMF operation.
The check for IDEV_GONE makes sure that the device in the abort path
really has control of the port with which it is associated. This
prevents starting hard resets at incorrect times and scheduling
unnecessary LUN resets for SATA devices.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ATAPI specific and STP general RNC suspension code had been
incorrectly removed from the remote device code.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Make sure that the wait for suspend can handle the RNC destruction case.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is an apparent HW lockup caused when the PE is disabled while there
is an outstanding TC in progress. This change puts the link into OOB to
force the TC to end before the PE is disabled.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This change adds timeouts to the RNC suspension wait. It makes the
suspend and resume timeouts the same.
The previous resume timeout of 5 ms was too short, and timeouts were
seen in resumptions of devices in the abort task/LUN reset path - which
would receive an RNC resumed message within a tenth of a second later.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Requests contructed as task management requests need to have the protocol
indicator set so the completion decode can observe any RNC suspension
conditions.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TMF requests, unlike normal I/O requests, need to handle I/O management
conditions in the completion function because TMFs are not handled in the
completion tasklet.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of TMF execution, or device resets, wait for the RNC to fully
resume before returning to the caller. This ensures that the remote
device will not fail I/O requests while waiting for the RNC resumption to
complete.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instead of immediately transitioning to the SCI_RNC_AWAIT_SUSPENSION
state, handle the SCI_RNC_RESUMING suspend transition from the
SCI_RNC_READY state like the SCI_RNC_INVALIDATING --> SCI_RNC_POSTING
transitions do now, by setting the destination state for the entry
into the READY state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When an individual request is being terminated, the request's tag
is managed in the terminate function.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch changes the callback mechanism to libsas to only occur while
the scic_lock is held; the abort path cleanup of I/Os also checks to make
sure IREQ_ABORT_PATH_ACTIVE is clear before proceding.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Completion of I/Os during the one of the abort path interface calls
from libsas can drive remote device state changes and the resumption
of the device RNC. This is a problem when the abort path is
attempting to cleanup outstanding I/O at the same time - the resumption
can prevent the termination from occuring correctly.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In order to prevent a device from receiving an I/O request while still
in an RNC suspending or resuming state (and therefore failing that
I/O back to libsas with a reset required status) wait for the RNC state
change before proceding in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the libsas error path, SATA disks require extra handling in
libata to recover operation. However, libsas expects to be able
to immediately recover all outstanding I/O once the error handler
escalation stops. This patch fixes the condition where the libata
error handler is scheduled for operation but libsas has already
deleted the outstanding sas_tasks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The LLHANG timer should be enabled once per device. This patch corrects
both the timer enable and the timer disable for the remote device.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of a suspend call while in SCI_RNC_POSTING or INVALIDATING
states, the LLHANG detect needed to be saved so the upcoming suspension
would enable it correctly. The unused suspend callback parameters were
removed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This addresses a regression from the commit "isci: Redesign
device suspension, abort, cleanup." in which the sas_task end
condition for terminated I/Os was made to call back on
sas_task_abort()".
This commit will be rolled into the original.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For NCQ error conditions among others, there is no need to enable
the link layer hang detect timer.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RNC can be any of the states in the loop from suspended to
ready when the API "suspend" or "resume" are called. This change
adds destination states parameters that control the suspension /
resumption action of the RNC statemachine for those transition states.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This commit changes the means by which outstanding I/Os are handled
for cleanup.
The likelihood is that this commit will be broken into smaller pieces,
however that will be a later revision. Among the changes:
- All completion structures have been removed from the tmf and
abort paths.
- Now using one completed I/O list, with the I/O completed in host bit being
used to select error or normal callback paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If LUN reset sees that the device is gone, it returns TMF_RESP_FUNC_FAILED
to cause libsas to escalate to an I_T_Nexus_Reset.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixing the remote device state machine to suspend and terminate
all outstanding I/O before the device stopped state is reached.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the remote device enters the NCQ error state, the device must
be suspended so that the I/O terminations can take place.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must be terminated only while the RNC is suspended. This commit
adds remote device suspensions and resumptions in the abort, reset and
termination paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must only be terminated when RNCs are suspended.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add comprehensive decode for all TC completions that generate RNC
suspensions.
Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU. The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.
This change enables the timer with the minimum period at the point
when the suspension is requested.
Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts. Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.
The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ notify waiters when controller stop completes (fixes 10 second stall
unloading the driver)
2/ make sure phy stop is after port and device stop
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Based on an original implementation by Ed Nadolski and Artur Wojcik
In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init(). Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations). The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().
The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful. In the case of isci we'll just re-init using a subset of the
normal driver load path.
[clean up some unused / mis-indented function definitions in host.h]
Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer. The other BC primitives have been
added to the sci_phy_event_handler()
Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
domain_device ->parent conveys the same information.
Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).
Fix up the rnc warnings to use the state name.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With the exception of the detached field, sg_mutex no longer adds any
locking. detached handling has been broken before and is still broken
and this patch does not seem to make things worse than they were to
begin with.
However, I have observed cases of tasks being blocked for >200s waiting
for sg_mutex. So the removal clearly adds value for very little cost.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sfds is protected by sg_index_lock - except for sg_open(), where it
isn't. Change that and add some documentation.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changes since v1: set_exclude now returns the new value, which gets
rid of the comma expression and the operator precedence bug. Thanks
to Douglas for spotting it.
sdp->exclude was previously protected by the BKL. The sg_mutex, which
replaced the BKL, only semi-protected it, as it was missing from
sg_release() and sg_proc_seq_show_debug(). Take an explicit spinlock
for it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
srp->done is protected by sfp->rq_list_lock everywhere, except for this
one case. Result can be that the wake-up happens before the cacheline
with the changed srp->done has arrived, so the waiter can go back to
sleep and never be woken up again.
The wait_event_interruptible() means that anyone trying to debug this
unlikely race will likely notice everything working fine again, as the
next signal will unwedge things. Evil.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
After sg_release() has been called, noone should be able to actually use
that filedescriptor anymore. So if closed ever made a difference in the
past five years or so, it would have meant a bug. Remove it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
[jejb: fix up checkpatch warnings]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Afaics the use of __wait_event_interruptible() as opposed to
wait_event_interruptible() is purely historic. So let's follow the rest
of the kernel and check the condition before prepare_to_wait() - and
also make the code a bit nicer.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The while (1) construct isn't actually a loop at all. So let's not
pretent and obfuscate the code.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
blocking is de-facto a constant and the now-removed comment wasn't all
that useful either. Without them and the resulting indentation the code
is a bit nicer to read.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dial back the aggressiveness of the controller lockup detection thread.
Currently it will declare the controller to be locked up if it goes
for 10 seconds with no interrupts and no change in the heartbeat
register. Dial back this to 30 seconds with no heartbeat change, and
also snoop the ioctl path and if a firmware flash command is detected,
dial it back further to 4 minutes until the firmware flash command
completes. The reason for this is that during the firmware flash
operation, the controller apparently doesn't update the heartbeat
register as frequently as it is supposed to, and we can get a false
positive.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Giridhar Malavali