Initialize caldata to avoid compilation warning.
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_main.o
drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"def_bool n" without prompt is pointless, this should be just "bool".
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was incorrectly introduced in d2730b2a6a. We
have already fixed function to use correct define, but forgot remove old one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 59eb21a650 "cfg80211: Extend channel to frequency mapping for 802.11j"
changed the definition of the ieee80211_channel_to_frequency; so fix its
usage in brcmfmac.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If any of the p54-based drivers are built with CONFIG_P54_LEDS not
defined, the following warning is generated:
CC [M] drivers/net/wireless/p54/main.o
drivers/net/wireless/p54/main.c: In function ‘p54_register_common’:
drivers/net/wireless/p54/main.c:614:21: warning: unused variable ‘priv’
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes pointed out the mess of external function prototypes in the
mac80211-ops.c file. Woe to anyone who changes these functions...
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb_wait_bit was designed for only one-bit bitmasks.
People start using it for multi-bit bitmasks. Make the "set" case
is safe for this. The "unset" case is already safe.
This does not change behavior of the current code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As warned by checkpatch.pl, use #include <linux/uaccess.h> instead of
<asm/uaccess.h>.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the new connection update parameter are accepted, the LE master
host sends the LE Connection Update Command to its controller informing
the new requested parameters.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.
2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make /sys/class/bluetooth/hciX a symlink to
path under corresponding tty.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the fail happens the HCI del_timer may timeout after the the hci dev
unregister. This lead to a kernel crash.
Reported-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Implements L2CAP Connection Parameter Update Response defined in
the Bluetooth Core Specification, Volume 3, Part A, section 4.21.
Address the LE Connection Parameter Procedure initiated by the slave.
Connection Interval Minimum and Maximum have the same range: 6 to
3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum.
The Slave Latency field shall have a value in the range of 0 to
((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall
be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms.
Multiplier field shall have a value in the range of 10 to 3200.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch splits the L2CAP command handling function in order to
have a clear separation between the commands related to BR/EDR and
LE. Commands and responses in the LE signaling channel are not being
handled yet, command reject is sent to all received requests. Bluetooth
Core Specification, Volume 3, Part A, section 4 defines the signaling
packets formats and allowed commands/responses over the LE signaling
channel.
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Separate LE and ACL timeouts. Othervise ACL connections
on non LE hw will time out after 45 secs.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix LE connections not being marked as master.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap over LE links can be disconnected without sending
disconnect command first.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add support for LE server sockets.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add basic LE connection support to L2CAP. LE
connection can be created by specifying cid
in struct sockaddr_l2
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth V4.0 adds support for Low Energy (LE) connections.
Specification introduces new set of hci commands to control LE
connection. This patch adds logic to create, cancel and disconnect
LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add needed HCI command and event structs to
create LE connections.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_load() was added to trigger l2cap.ko module loading from the RFCOMM
and BNEP modules. Now that L2CAP module is gone, we don't need it anymore.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
WFA certification and the WMM spec require that we
always reply to unicast probe requests, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit: "p54: enhance rssi->dBm database import"
changed the way how the driver deals with the
rssical data. A new data format was necessary
and hence this patch.
NOTE: (for users with a custom eeprom binary)
I spent some time updating p54tools to support
the new format too: => (git available from)
http://git.kernel.org/?p=linux/kernel/git/chr/p54tools.git
It now comes with a simplistic script "n800_rssi2v2.sh"
which can be used to automate the conversion.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes several shortcomings of the
previous implementation. Features of the
rewrite include:
* handles undocumented "0x0000" word at the
start of the frequency table.
(Affected some early? DELL 1450 USB devices
and my Symbol 5GHz miniPCI card.)
* supports more than just one reference point
per band. (Also needed for the Symbol card.)
* ships with default values in case the eeprom
data is damaged, absent or unsupported.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some channel indices of the low 5GHz band clash with
those of the 2.4GHz band. Therefore we should go
with the channel's center frequency.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Case assert is violated should be quite unlikely.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.
This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.
It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_h_check returned RX_DROP_MONITOR in case the if statement
in question was true but the same return value is also used directly
after the if clause. Hence, we can just drop the whole if clause and as
such simplify the code.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan