Under load, my SysKonnect SK-9S22 sees duplicate checksums from
earlier packets. Doesn't happen on other platforms so just disable
receive checksum there.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Turn symmetric flow control on by default. This was an oversight
in the initial versions.
Signed-off-by: Stephen HEmminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a couple more prefetches to where we walk the rings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Put more logic in to try and handle transmit timeout recovery.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adjust interrupt deferral values for better performance and avoid
starvation issues under stress.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Optimize poll routine by not clearing interrupt till after
processing, and checking for more work before re-enable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change transmit complete handling to use the status values
in the poll list because they are in-cache, rather than reading
non-cached memory for chips status.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some transmit side small fixes:
* When computing number of list elements per transmit, do full
comparision to check for checksuming.
* Get rid of racy check for tx_complete
* Change stop test to match wake condition.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Split Tx and Rx ring into two different data structures.
Tx needs the next value (to handle partial status), and
Rx always needs the mapaddr (to handle resubmitting same buffer).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to keep track of mapping length in ring structure
because we can get the same info from other info.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to disable interrupts during the transmit routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do phy processing in a work queue rather than a tasklet.
This means we can let bottom halves run.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for get/set the interrupt coalescing settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make the copy threshold a module parameter for those who
may want to turn it off.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It is a useful optimization to rearrange the structure
slightly to align receive and transmit portions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There maybe new versions of Yukon2 in the future, so make the
driver more robust to handle this.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This reverts commit 1b0997f561, which in
turn reverted 34ea80ec6a (which is thus
re-instated).
Quoth James Bottomley:
"All it's doing is deferring the device_put() from the
scsi_put_command() to after the scsi_run_queue(), which doesn't fix
the sleep while atomic problem of the device release method. In both
cases we still get the semaphore in atomic context problem which is
caused by scsi_reap_target() doing a device_del(), which I assumed
(wrongly) was valid from atomic context."
who also promised to fix scsi_reap_target().
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The raid5 stripe cache was recently changed from fixed size (NR_STRIPES) to
variable size (conf->max_nr_stripes). However there are two places that still
use the constant and as a result, reducing the size of the stripe cache can
result in a deadlock.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Who would submit code with a FIXME like that in it !!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_MAX_RAW_DEVS should appear immediately after CONFIG_RAW_DRIVER.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has been broken for months. On resume, we call acpi_pci_link_set()
with interrupts off, so we get a warning when we try to do a kmalloc of non
atomic memory. The actual allocation is just 2 long's (plus extra byte for
some reason I can't fathom), so a simple conversion to GFP_ATOMIC is
probably the safest way to fix this.
The error looks like this..
Debug: sleeping function called from invalid context at mm/slab.c:2486
in_atomic():0, irqs_disabled():1
[<c0143f6c>] kmem_cache_alloc+0x40/0x56
[<c0206a2e>] acpi_pci_link_set+0x3f/0x17f
[<c0206f96>] irqrouter_resume+0x1e/0x3c
[<c0239bca>] __sysdev_resume+0x11/0x6b
[<c0239e88>] sysdev_resume+0x34/0x52
[<c023de21>] device_power_up+0x5/0xa
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hitting BUG_ON() in __alloc_bootmem_core() when there is no free page
available in the first node's memory. For the case of kdump on PPC64
(Power 4 machine), the captured kernel is used two memory regions - memory
for TCE tables (tce-base and tce-size at top of RAM and reserved) and
captured kernel memory region (crashk_base and crashk_size). Since we
reserve the memory for the first node, we should be returning from
__alloc_bootmem_core() to search for the next node (pg_dat).
Currently, find_next_zero_bit() is returning the n^th bit (eidx) when there
is no free page. Then, test_bit() is failed since we set 0xff only for the
actual size initially (init_bootmem_core()) even though rounded up to one
page for bdata->node_bootmem_map. We are hitting the BUG_ON after failing
to enter second "for" loop.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I realized ZONE_DMA32 has a trivial bug at Kconfig for ia64. In
include/linux/gfp.h on 2.6.15-rc5-mm1, CONFIG is define like followings.
#ifdef CONFIG_DMA_IS_DMA32
#define __GFP_DMA32 ((__force gfp_t)0x01) /* ZONE_DMA is ZONE_DMA32
*/
:
:
So, CONFIG_"ZONE"_DMA_IS_DMA32 is clearly wrong.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The bd62266319 commit broke the UCB1x00
touchscreen driver since the idev structure was assumed to be into the ts
structure, simply casting the former to the later in a couple places.
This patch fixes those, and also cache the idev pointer between multiple
calls to input_report_abs() to avoid growing the compiled code needlessly.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Spotted by a Fedora user. Compiling with DEBUG_PARPORT set fails due to
the broken cast.
Just remove it.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For Kprobes critical path is the path from debug break exception handler
till the control reaches kprobes exception code. No probes can be
supported in this path as we will end up in recursion.
This patch prevents this by moving the below function to safe __kprobes
section onto which no probes can be inserted.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IPMI specifcation says the generator ID is 0x20, but that is for bits
7-1. Bit 0 is set to specify it is a software event. The correct value is
0x41. Without this fix, panic events written into the System Event Log
appear to come from an "unknown" generator, rather than from the kernel.
Signed-off-by: Jordan Hargrave <Jordan_Hargrave@dell.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The Pinnacle PCTV Stereo needs tda9887 port2 set to 1
- Without this patch, mt20xx tuner is not detected and the board
doesn't tune.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Page count should be initialized to 1 on each of the MIPS empty zero pages,
to avoid a bad_page warning whenever one of them is freed from all mappings.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kauditd was causing suspends to fail because it refused to freeze. Adding
a try_to_freeze() to its sleep loop solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/um/kernel/tt/uaccess.c: In function `copy_from_user_tt':
arch/um/kernel/tt/uaccess.c:11: error: `FIXADDR_USER_START' undeclared (first use in this function)
arch/um/kernel/tt/uaccess.c:11: error: (Each undeclared identifier is reported only once
arch/um/kernel/tt/uaccess.c:11: error: for each function it appears in.)
I get the compile error when I disable CONFIG_MODE_SKAS.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The below patch lets userspace have more control over the inodes that
inotify will watch. It introduces two new flags.
IN_ONLYDIR -- only watch the inode if it is a directory.
This is needed to avoid the race that can occur when we want to be
sure that we are watching a directory.
IN_DONT_FOLLOW -- don't follow a symlink. In combination
with IN_ONLYDIR we can make sure that we don't watch the target of
symlinks.
The issues the flags fix came up when writing the gnome-vfs inotify
backend. Default behaviour is unchanged.
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org>
Acked-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This undoes the put_disk patch I sent in before.
If I had been paying attention I would have seen that we call put_disk
from free_hba during driver unload. That's the only time we want to
call it. If it's called from deregister disk we may remove the
controller (cNd0) unintentionally.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When registering multiple kprobes at the same address, we leave a small
window where the kprobe hlist will not contain a reference to the
registered kprobe, leading to potentially, a system crash if the breakpoint
is hit on another processor.
Patch below now automically relpace the old kprobe with the new
kprobe from the hash list.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add list_replace_rcu: replace old entry by new one.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a timestamp field to the events sent via the process event
connector. The timestamp allows listeners to accurately account the
duration(s) between a process' events and offers strong means with which
to determine the order of events with respect to a given task while also
avoiding the addition of per-task data.
This alters the size and layout of the event structure and hence would
break compatibility if process events connector as it stands in 2.6.15-rc2
were released as a mainline kernel.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are several functions that might seem appropriate for a timestamp:
get_cycles()
current_kernel_time()
do_gettimeofday()
<read jiffies/jiffies_64>
Each has problems with combinations of SMP-safety, low resolution, and
monotonicity. This patch adds a new function that returns a monotonic SMP-safe
timestamp with nanosecond resolution where available.
Changes:
Split timestamp into separate patch
Moved to kernel/time.c
Renamed to getnstimestamp
Fixed unintended-pointer-arithmetic bug
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit f549d6c18c introduced a generic
fallback for security xattrs, but appears to include a subtle bug.
Gentoo users with kernels with selinux compiled in, and coreutils compiled
with acl support, noticed that they could not copy files on tmpfs using
'cp'.
cp (compiled with acl support) copies the file, lists the extended
attributes on the old file, copies them all to the new file, and then
exits. However the listxattr() calls were failing with this odd behaviour:
llistxattr("a.out", (nil), 0) = 17
llistxattr("a.out", 0x7fffff8c6cb0, 17) = -1 ERANGE (Numerical result out of
range)
I believe this is a simple problem in the logic used to check the buffer
sizes; if the user sends a buffer the exact size of the data, then its ok
:)
This change solves the problem.
More info can be found at http://bugs.gentoo.org/113138
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Accessing nohz_cpu_mask before incrementing rcp->cur is racy. It can cause
tickless idle CPUs to be included in rsp->cpumask, which will extend
graceperiods unnecessarily.
Fix this race. It has been tested using extensions to RCU torture module
that forces various CPUs to become idle.
Signed-off-by: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
