This effectively reverts commit 61d047be99.
Disabling the IOMMU can potetially allow DMA transactions to
complete without being translated. Leave it enabled, and allow
crash kernel to do the IOMMU reinitialization properly.
Cc: stable@kernel.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
To catch future potential issues we can add a warning whenever we issue
a command before the command buffer is fully initialized.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Hit another kdump problem as reported by Neil Horman. When initializaing
the IOMMU, we attach devices to their domains before the IOMMU is
fully (re)initialized. Attaching a device will issue some important
invalidations. In the context of the newly kexec'd kdump kernel, the
IOMMU may have stale cached data from the original kernel. Because we
do the attach too early, the invalidation commands are placed in the new
command buffer before the IOMMU is updated w/ that buffer. This leaves
the stale entries in the kdump context and can renders device unusable.
Simply enable the IOMMU before we do the attach.
Cc: stable@kernel.org
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The Microblaze dynamic ftrace code assumes a call ordering that is not met
in all scenarios. Specifically, executing a command similar to:
echo 105 > /sys/kernel/debug/tracing/set_ftrace_pid
before any other tracing-related commands results in a kernel panic:
BUG: failure at arch/microblaze/kernel/ftrace.c:198/ftrace_update_ftrace_func()!
Recoding ftrace_update_ftrace_func() to use &ftrace_caller directly eliminates
the need to capture its address elsewhere (and thus rely on a particular call
sequence).
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
According to Intel Software Devel Manual Volume 3B, the
Nehalem-EX PMU is just like regular Nehalem (except for the
uncore support, which is completely different).
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <alpine.DEB.2.00.1004060956580.1417@cl320.eecs.utk.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ 29 has two possible interrupts DDRINT and RTC, but having both in
the default priority table is confusing (and triggers a warning from
sparse.)
This patch removes the lower priority DDRINT from the default priority
table leaving the RTC setting as the default.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes an issue where a DMA channel can erroneously process an
event generated by a previous transfer. A failure case is where DMA is
being used for SPI transmit and receive channels on OMAP L138. In this
case there is a single bit that controls all event generation from the
SPI peripheral. Therefore it is possible that between when edma_stop()
has been called for the transmit channel on a previous transfer and
edma_start() is called for the transmit channel on a subsequent transfer,
that a transmit event has been generated.
The fix is to clear events in edma_start(). This prevents false events
from being processed when events are enabled for that channel.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.
This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.
Reported-by: Shanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da830, when the same timer is used for clocksource and clockevent,
the timer can be started before the clockevent is
registered/initialzed. This creates a window where a timer
interrupt might fire before the clockevent handler has been
setup and causes a crash.
This patch moves the actual enable/start of the timer after
the clockevent has ben registered.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Always build the powerpc perf_arch_fetch_caller_regs version
perf: Always build the stub perf_arch_fetch_caller_regs version
perf, probe-finder: Build fix on Debian
perf/scripts: Tuple was set from long in both branches in python_process_event()
perf: Fix 'perf sched record' deadlock
perf, x86: Fix callgraphs of 32-bit processes on 64-bit kernels
perf, x86: Fix AMD hotplug & constraint initialization
x86: Move notify_cpu_starting() callback to a later stage
x86,kgdb: Always initialize the hw breakpoint attribute
perf: Use hot regs with software sched switch/migrate events
perf: Correctly align perf event tracing buffer
We provide regs->tstate, regs->tpc, regs->tnpc and
regs->u_regs[UREG_FP].
regs->tstate is necessary for:
user_mode() (via perf_exclude_event())
perf_misc_flags() (via perf_prepare_sample())
regs->tpc is necessary for:
perf_instruction_pointer() (via perf_prepare_sample())
and regs->u_regs[UREG_FP] is necessary for:
perf_callchain() (via perf_prepare_sample())
The regs->tnpc value is provided just to be tidy.
Signed-off-by: David S. Miller <davem@davemloft.net>
vmemmap_populate() attempts to report the used index and total size of
vmemmap_table, but it wrongly shifts the total size so that it is
always shown as 0.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that software events use perf_arch_fetch_caller_regs() too, we
need the powerpc version to be always built.
Fixes the following build error:
(.text+0x3210): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x3324): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x33bc): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x33ec): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0xd4a0): undefined reference to `perf_arch_fetch_caller_regs'
arch/powerpc/kernel/built-in.o:(.text+0xd528): more undefined references to `perf_arch_fetch_caller_regs' follow
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/5200: in lpbfifo, flag DMA irqs as enabled after requesting them
powerpc/fsl: add device tree binding for QE firmware
of/flattree: Fix unhandled OF_DT_NOP tag when unflattening the device tree
Jan Grossmann reported kernel boot panic while booting SMP
kernel on his system with a single core cpu. SMP kernels call
enable_IR_x2apic() from native_smp_prepare_cpus() and on
platforms where the kernel doesn't find SMP configuration we
ended up again calling enable_IR_x2apic() from the
APIC_init_uniprocessor() call in the smp_sanity_check(). Thus
leading to kernel panic.
Don't call enable_IR_x2apic() and default_setup_apic_routing()
from APIC_init_uniprocessor() in CONFIG_SMP case.
NOTE: this kind of non-idempotent and assymetric initialization
sequence is rather fragile and unclean, we'll clean that up
in v2.6.35. This is the minimal fix for v2.6.34.
Reported-by: Jan.Grossmann@kielnet.net
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <jbarnes@virtuousgeek.org>
Cc: <david.woodhouse@intel.com>
Cc: <weidong.han@intel.com>
Cc: <youquan.song@intel.com>
Cc: <Jan.Grossmann@kielnet.net>
Cc: <stable@kernel.org> # [v2.6.32.x, v2.6.33.x]
LKML-Reference: <1270083887.7835.78.camel@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When profiling a 32-bit process on a 64-bit kernel, callgraph tracing
stopped after the first function, because it has seen a garbage memory
address (tried to interpret the frame pointer, and return address as a
64-bit pointer).
Fix this by using a struct stack_frame with 32-bit pointers when the
TIF_IA32 flag is set.
Note that TIF_IA32 flag must be used, and not is_compat_task(), because
the latter is only set when the 32-bit process is executing a syscall,
which may not always be the case (when tracing page fault events for
example).
Signed-off-by: Török Edwin <edwintorok@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
LKML-Reference: <1268820436-13145-1-git-send-email-edwintorok@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 3f6da39 ("perf: Rework and fix the arch CPU-hotplug hooks") moved
the amd northbridge allocation from CPUS_ONLINE to CPUS_PREPARE_UP
however amd_nb_id() doesn't work yet on prepare so it would simply bail
basically reverting to a state where we do not properly track node wide
constraints - causing weird perf results.
Fix up the AMD NorthBridge initialization code by allocating from
CPU_UP_PREPARE and installing it from CPU_STARTING once we have the
proper nb_id. It also properly deals with the allocation failing.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ robustify using amd_has_nb() ]
Signed-off-by: Stephane Eranian <eranian@google.com>
LKML-Reference: <1269353485.5109.48.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Because we need to have cpu identification things done by the time we run
CPU_STARTING notifiers.
( This init ordering will be relied on by the next fix. )
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1269353485.5109.48.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some larger systems require more than 512 nodes, so increase the
maximum CONFIG_NODES_SHIFT to 10 for a new max of 1024 nodes.
This was tested with numa=fake=64M on systems with more than
64GB of RAM. A total of 1022 nodes were initialized.
Successfully builds with no additional warnings on x86_64
allyesconfig.
( No effect on any existing config. Newly enabled CONFIG_MAXSMP=y
will see the new default. )
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1003251538060.8589@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sh/for-2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up the SH-3 build for recent TLB changes.
sh: export return_address() symbol.
sh: Enable the mmu in start_secondary()
sh: Fix FDPIC binary loader
arch/sh/kernel: Use set_cpus_allowed_ptr
sh: Update ecovec_defconfig
USB gadget r8a66597-udc.c: duplicated include
sh: update the TLB replacement counter for entry wiring.
While the MMUCR.URB and ITLB/UTLB differentiation works fine for all SH-4
and later TLBs, these features are absent on SH-3. This splits out
local_flush_tlb_all() in to SH-4 and PTEAEX copies while restoring the
old SH-3 one, subsequently fixing up the build.
This will probably want some further reordering and tidying in the
future, but that's out of scope at present.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows arch code could decide the way to reserve the ibft.
And we should reserve ibft as early as possible, instead of BOOTMEM
stage, in case the table is in RAM range and is not reserved by BIOS
(this will often be the case.)
Move to just after find_smp_config().
Also when CONFIG_NO_BOOTMEM=y, We will not have reserve_bootmem() anymore.
-v2: fix typo about ibft pointed by Konrad Rzeszutek Wilk <konrad@darnok.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4BB510FB.80601@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Jones <pjones@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
CC: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We think there exists a bug in the HPET code that emulates the RTC.
In the normal case, when the RTC frequency is set, the rtc driver tells
the hpet code about it here:
int hpet_set_periodic_freq(unsigned long freq)
{
uint64_t clc;
if (!is_hpet_enabled())
return 0;
if (freq <= DEFAULT_RTC_INT_FREQ)
hpet_pie_limit = DEFAULT_RTC_INT_FREQ / freq;
else {
clc = (uint64_t) hpet_clockevent.mult * NSEC_PER_SEC;
do_div(clc, freq);
clc >>= hpet_clockevent.shift;
hpet_pie_delta = (unsigned long) clc;
}
return 1;
}
If freq is set to 64Hz (DEFAULT_RTC_INT_FREQ) or lower, then
hpet_pie_limit (a static) is set to non-zero. Then, on every one-shot
HPET interrupt, hpet_rtc_timer_reinit is called to compute the next
timeout. Well, that function has this logic:
if (!(hpet_rtc_flags & RTC_PIE) || hpet_pie_limit)
delta = hpet_default_delta;
else
delta = hpet_pie_delta;
Since hpet_pie_limit is not 0, hpet_default_delta is used. That
corresponds to 64Hz.
Now, if you set a different rtc frequency, you'll take the else path
through hpet_set_periodic_freq, but unfortunately no one resets
hpet_pie_limit back to 0.
Boom....now you are stuck with 64Hz RTC interrupts forever.
The patch below just resets the hpet_pie_limit value when requested freq
is greater than DEFAULT_RTC_INT_FREQ, which we think fixes this problem.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <201003112200.o2BM0Hre012875@imap1.linux-foundation.org>
Signed-off-by: Daniel Hecht <dhecht@vmware.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On Wed, Feb 24, 2010 at 03:37:04PM -0800, Justin Piszcz wrote:
> Hello,
>
> Again, on the Intel DP55KG board:
>
> # uname -a
> Linux host 2.6.33 #1 SMP Wed Feb 24 18:31:00 EST 2010 x86_64 GNU/Linux
>
> [ 1.237600] ------------[ cut here ]------------
> [ 1.237890] WARNING: at arch/x86/kernel/hpet.c:404 hpet_next_event+0x70/0x80()
> [ 1.238221] Hardware name:
> [ 1.238504] hpet: compare register read back failed.
> [ 1.238793] Modules linked in:
> [ 1.239315] Pid: 0, comm: swapper Not tainted 2.6.33 #1
> [ 1.239605] Call Trace:
> [ 1.239886] <IRQ> [<ffffffff81056c13>] ? warn_slowpath_common+0x73/0xb0
> [ 1.240409] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.240699] [<ffffffff81056cb0>] ? warn_slowpath_fmt+0x40/0x50
> [ 1.240992] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241281] [<ffffffff81041ad0>] ? hpet_next_event+0x70/0x80
> [ 1.241573] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241859] [<ffffffff81078e32>] ? tick_handle_oneshot_broadcast+0xe2/0x100
> [ 1.246533] [<ffffffff8102a67a>] ? timer_interrupt+0x1a/0x30
> [ 1.246826] [<ffffffff81085499>] ? handle_IRQ_event+0x39/0xd0
> [ 1.247118] [<ffffffff81087368>] ? handle_edge_irq+0xb8/0x160
> [ 1.247407] [<ffffffff81029f55>] ? handle_irq+0x15/0x20
> [ 1.247689] [<ffffffff810294a2>] ? do_IRQ+0x62/0xe0
> [ 1.247976] [<ffffffff8146be53>] ? ret_from_intr+0x0/0xa
> [ 1.248262] <EOI> [<ffffffff8102f277>] ? mwait_idle+0x57/0x80
> [ 1.248796] [<ffffffff8102645c>] ? cpu_idle+0x5c/0xb0
> [ 1.249080] ---[ end trace db7f668fb6fef4e1 ]---
>
> Is this something Intel has to fix or is it a bug in the kernel?
This is a chipset erratum.
Thomas: You mentioned we can retain this check only for known-buggy and
hpet debug kind of options. But here is the simple workaround patch for
this particular erratum.
Some chipsets have a erratum due to which read immediately following a
write of HPET comparator returns old comparator value instead of most
recently written value.
Erratum 15 in
"Intel I/O Controller Hub 9 (ICH9) Family Specification Update"
(http://www.intel.com/assets/pdf/specupdate/316973.pdf)
Workaround for the errata is to read the comparator twice if the first
one fails.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20100225185348.GA9674@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com>
Cc: <stable@kernel.org>
We found a system where the MP table MPC and MPF structures overlap.
That doesn't really matter because the mptable is not used anyways with ACPI,
but it leads to a panic in the early allocator due to the overlapping
reservations in 2.6.33.
Earlier kernels handled this without problems.
Simply change these reservations to reserve_early_overlap_ok to avoid
the panic.
Reported-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100329074111.GA22821@basil.fritz.box>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Word copying is used only for aligned addresses.
Here is space for improving to use any better copying technique.
Look at memcpy implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
TLB size was hardcoded in asm code. This patch brings ability
to change TLB size only in one place. (mmu.h).
Signed-off-by: Michal Simek <monstr@monstr.eu>
When the system has no lmb bram, main memory should be start from
zero because of microblaze vectors.
DTS fragment could look like:
DDR2_SDRAM: memory@0 {
device_type = "memory";
reg = < 0x0 0x10000000 >;
} ;
Then you have to setup CONFIG_KERNEL_BASE_ADDR=0 which caused
that kernel physical start address will be zero. On reset vector place
will be jump to 0x100 and on 0x100 starts kernel text.
You have to solve how to load the kernel before cpu starts.
Tested with XMD.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Here is small regression on dhrystone tests and I think
that on all benchmarking tests. It is due to better checking
mechanism in put_user macro
Signed-off-by: Michal Simek <monstr@monstr.eu>
This is the first patch which does uaccess unification.
I choosed to do several patches to be able to use bisect
in future if any fault happens.
Signed-off-by: Michal Simek <monstr@monstr.eu>
If CONFIG_INITRAMFS_SOURCE is set, "scripts/gen_initramfs_list.sh"
checks if the cpio image exists. Remove the duplicate check from the
Makefile.
Remove the "clean-kernel" variable which is unused in the Makefile and
is not used by the Kbuild.
Signed-off-by: Arun Bhanu <arun@bhanu.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
'make clean' does not to delete the following build generated file:
arch/microblaze/boot/linux.bin.ub
'make mrproper' does not to delete the following build generated files:
arch/microblaze/boot/simpleImage.*
Fix the Makefile to delete these build generated files.
See [1] for a discussion on why simpleImage.* files are deleted with 'make
mrproper' and not with 'make clean'.
[1] http://lkml.org/lkml/2010/3/12/96
Signed-off-by: Arun Bhanu <arun@bhanu.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
'make ARCH=microblaze help' fails with the following error due to a
missing single quote.
/bin/sh: -c: line 0: unexpected EOF while looking for matching `''
/bin/sh: -c: line 1: syntax error: unexpected end of file
make: *** [help] Error 2
Signed-off-by: Arun Bhanu <arun@bhanu.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The "kstack=" command line parameter is not parsed correctly.
All proper values are interpreted as zero.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
It is required to call hw_breakpoint_init() on an attr before using it
in any other calls. This fixes the problem where kgdb will sometimes
fail to initialize on x86_64.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: 2.6.33 <stable@kernel.org>
LKML-Reference: <1269975907-27602-1-git-send-email-jason.wessel@windriver.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Scheduler's task migration events don't work because they always
pass NULL regs perf_sw_event(). The event hence gets filtered
in perf_swevent_add().
Scheduler's context switches events use task_pt_regs() to get
the context when the event occured which is a wrong thing to
do as this won't give us the place in the kernel where we went
to sleep but the place where we left userspace. The result is
even more wrong if we switch from a kernel thread.
Use the hot regs snapshot for both events as they belong to the
non-interrupt/exception based events family. Unlike page faults
or so that provide the regs matching the exact origin of the event,
we need to save the current context.
This makes the task migration event working and fix the context
switch callchains and origin ip.
Example: perf record -a -e cs
Before:
10.91% ksoftirqd/0 0 [k] 0000000000000000
|
--- (nil)
perf_callchain
perf_prepare_sample
__perf_event_overflow
perf_swevent_overflow
perf_swevent_add
perf_swevent_ctx_event
do_perf_sw_event
__perf_sw_event
perf_event_task_sched_out
schedule
run_ksoftirqd
kthread
kernel_thread_helper
After:
23.77% hald-addon-stor [kernel.kallsyms] [k] schedule
|
--- schedule
|
|--60.00%-- schedule_timeout
| wait_for_common
| wait_for_completion
| blk_execute_rq
| scsi_execute
| scsi_execute_req
| sr_test_unit_ready
| |
| |--66.67%-- sr_media_change
| | media_changed
| | cdrom_media_changed
| | sr_block_media_changed
| | check_disk_change
| | cdrom_open
v2: Always build perf_arch_fetch_caller_regs() now that software
events need that too. They don't need it from modules, unlike trace
events, so we keep the EXPORT_SYMBOL in trace_event_perf.c
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
We have to adjust 'reg_window' down by 16 becuase the 'pos' iterator
we'll use to index into the stack slots will be between 16 and 32.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty found on lguest with trim_bios_range, max_pfn is not right anymore, and
looks e820_remove_range does not work right.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] LGUEST: 0000000000000000 - 0000000004000000 (usable)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
[ 0.000000] DMI not present or invalid.
[ 0.000000] last_pfn = 0x3fa0 max_arch_pfn = 0x100000
[ 0.000000] init_memory_mapping: 0000000000000000-0000000003fa0000
root cause is: the e820_remove_range doesn't handle the all covered
case. e820_remove_range(BIOS_START, BIOS_END - BIOS_START, ...)
produces a bogus range as a result.
Make it match e820_update_range() by handling that case too.
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <4BB18E55.6090903@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The enable bit for dpll4_m4x2 clock should be OMAP3430_PWRDN_DSS1_SHIFT.
The code erroneously uses OMAP3430_PWRDN_CAM_SHIFT which is meant for
dpll4_m5x2 clock.
This came into notice during a recent review of the clock tree.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes usage of bitwise OR in if conditions, and instead
uses logical OR.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Abhijit Pagare <abhijitpagare@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch corrects the width of sysc_flags in hwmod sysconfig structure
where the values to be stored to this variable exceed the current
field width.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: edited to apply; rearranged structure members to pack]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds check for presence of clockdomain structure in the API
omap_hwmod_get_pwrdm before trying to access the powerdomain structure.
This will prevent unnecessary crashing of the system in case of a
clock node with out an associated clockdomain.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Colin King reported a strange oops in S4 resume code path (see below). The test
system has i5/i7 CPU. The kernel doesn't open PAE, so 4M page table is used.
The oops always happen a virtual address 0xc03ff000, which is mapped to the
last 4k of first 4M memory. Doing a global tlb flush fixes the issue.
EIP: 0060:[<c0493a01>] EFLAGS: 00010086 CPU: 0
EIP is at copy_loop+0xe/0x15
EAX: 36aeb000 EBX: 00000000 ECX: 00000400 EDX: f55ad46c
ESI: 0f800000 EDI: c03ff000 EBP: f67fbec4 ESP: f67fbea8
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
...
...
CR2: 00000000c03ff000
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <20100305005932.GA22675@sli10-desk.sh.intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Do not free zero sized per cpu areas
x86: Make sure free_init_pages() frees pages on page boundary
x86: Make smp_locks end with page alignment
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Including slab.h from x86 pgtable_32.h creates a troublesome
dependency chain w/ ftrace enabled. The following chain leads to
inclusion of pgtable_32.h from define_trace.h.
trace/define_trace.h
trace/ftrace.h
linux/ftrace_event.h
linux/ring_buffer.h
linux/mm.h
asm/pgtable.h
asm/pgtable_32.h
slab.h itself defines trace hooks via
linux/sl[aou]b_def.h
linux/kmemtrace.h
trace/events/kmem.h
If slab.h is not included before define_trace.h is included, this
leads to duplicate definitions of kmemtrace hooks or other include
dependency problems.
pgtable_32.h doesn't need slab.h to begin with. Don't include it from
there.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
This add USB Host capability. The Armadillo 500 board is supplied
with two USB Host connectors driven by the USB OTG and USB Host 2
ports, through two NXP isp 1504 transceivers.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch/arm/mach-mx3/mx31lite-db.c: linux/platform_device.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch/arm/mach-mx3/mach-pcm037.c: linux/fsl_devices.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for build-in watchdog device found on
Freescale imx31 and imx35 SoCs.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Properly truncate pt_regs framepointer in perf callback.
arch/sparc/kernel: Use set_cpus_allowed_ptr
sparc: Fix use of uid16_t and gid16_t in asm/stat.h
For 32-bit processes, we save the full 64-bits of the regs in pt_regs.
But unlike when the userspace actually does load and store
instructions, the top 32-bits don't get automatically truncated by the
cpu in kernel mode (because the kernel doesn't execute with PSTATE_AM
address masking enabled).
So we have to do it by hand.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NO_BOOTMEM=y, it could use memory more effiently, or
in a more compact fashion.
Example:
Allocated new RAMDISK: 00ec2000 - 0248ce57
Move RAMDISK from 000000002ea04000 - 000000002ffcee56 to 00ec2000 - 0248ce56
The new RAMDISK's end is not page aligned.
Last page could be shared with other users.
When free_init_pages are called for initrd or .init, the page
could be freed and we could corrupt other data.
code segment in free_init_pages():
| for (; addr < end; addr += PAGE_SIZE) {
| ClearPageReserved(virt_to_page(addr));
| init_page_count(virt_to_page(addr));
| memset((void *)(addr & ~(PAGE_SIZE-1)),
| POISON_FREE_INITMEM, PAGE_SIZE);
| free_page(addr);
| totalram_pages++;
| }
last half page could be used as one whole free page.
So page align the boundaries.
-v2: make the original initramdisk to be aligned, according to
Johannes, otherwise we have the chance to lose one page.
we still need to keep initrd_end not aligned, otherwise it could
confuse decompressor.
-v3: change to WARN_ON instead, suggested by Johannes.
-v4: use PAGE_ALIGN, suggested by Johannes.
We may fix that macro name later to PAGE_ALIGN_UP, and PAGE_ALIGN_DOWN
Add comments about assuming ramdisk start is aligned
in relocate_initrd(), change to re get ramdisk_image instead of save it
to make diff smaller. Add warning for wrong range, suggested by Johannes.
-v6: remove one WARN()
We need to align beginning in free_init_pages()
do not copy more than ramdisk_size, noticed by Johannes
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1269830604-26214-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit b26b2d494b ("resource/PCI: align functions now return start
of resource") added lines with missing semicolons.
Add the missing semicolons to the FRV and CRIS arch code.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: linux@dominikbrodowski.net
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When compiling the kernel to Thumb-2, using a 16-bit NOP in the
memmove() implementation causes the preceding ADD PC instruction to
branch incorrectly in the middle of a 32-bit LDR or STR instruction. The
memmove() code is now similar to the memcpy() template.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current implementation of jprobes allocates empty pt_regs from the
stack which is then passed to kprobe_handler() and eventually to
singlestep(). Now when instruction being simulated is STMFD (like
in normal function prologues without CONFIG_FRAME_POINTER), stores
using SP actually write over top of the fabricated pt_regs
structure.
This can be reproduced for example by using LKDTM module:
# modprobe lkdtm
# mount -t debugfs none /sys/kernel/debug
# echo PANIC > /sys/kernel/debug/provoke-crash/INT_HW_IRQ_EN
after this, it fails with corrupted registers (before the requested crash would occur):
lkdtm: Crash point INT_HW_IRQ_EN of type PANIC hit, trigger in 9 rounds
lkdtm: Crash point INT_HW_IRQ_EN of type PANIC hit, trigger in 8 rounds
Internal error: Oops - undefined instruction: 0 [#1]
last sysfs file: /sys/devices/platform/serial8250.0/sleep_timeout
Modules linked in: lkdtm
CPU: 0 Not tainted (2.6.34-rc2 #69)
PC is at irq_desc+0x1638/0xeeb0
LR is at 0x25
pc : [<c050b428>] lr : [<00000025>] psr: c80a0013
sp : ce94bd60 ip : c050b3e8 fp : a0000013
r10: c0aa453c r9 : cf5d4000 r8 : ce9a1822
r7 : c050b424 r6 : 00000025 r5 : c039d8f8 r4 : c050b3e8
r3 : 00000001 r2 : cf4d0440 r1 : c039d8f8 r0 : 00000020
Flags: NZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 8e804019 DAC: 00000015
Process sh (pid: 496, stack limit = 0xce94a2e8)
Stack: (0xce94bd60 to 0xce94c000)
[...]
Code: 000002cd 00000000 00000000 00000001 (dead4ead)
---[ end trace 2b46d5f2b682f370 ]---
Kernel panic - not syncing: Fatal exception in interrupt
This patch allocates enough space (2 * sizeof(struct pt_regs)) from
the stack to prevent such corruption.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clkdev.h is using struct device *. Due to this compilation
warning is comming. Removing this warning.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq.h is using struct pt_regs *. Due to this compilation
warning is comming. Removing this warning by adding declaration
of struct pt_regs.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ensure that the aux table is properly initialized, even when optional
features are missing. Without this, the FDPIC loader did not work.
Signed-off-by: Andrew Stubbs <ams@codesourcery.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A CPU has VFPv3 hardware if the FPSID[19:16] bits are 2 or more.
Currently Linux was only checking for 3 or more.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids unbalanced enable/disable messages for the DMA
interrupts when running the 5200 platform SCLPC/BestComm driver in DMA
mode.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
x86/PCI: for host bridge address space collisions, show conflicting resource
frv/PCI: remove redundant warnings
x86/PCI: remove redundant warnings
PCI: don't say we claimed a resource if we failed
PCI quirk: Disable MSI on VIA K8T890 systems
PCI quirk: RS780/RS880: work around missing MSI initialization
PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
PCI: complain about devices that seem to be broken
PCI: print resources consistently with %pR
PCI: make disabled window printk style match the enabled ones
PCI: break out primary/secondary/subordinate for readability
PCI: for address space collisions, show conflicting resource
resources: add interfaces that return conflict information
PCI: cleanup error return for pcix get and set mmrbc functions
PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
PCI: kill off pci_register_set_vga_state() symbol export.
PCI: fix return value from pcix_get_max_mmrbc()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Restrict usage of c1e_idle()
x86: Fix placement of FIX_OHCI1394_BASE
x86: Handle legacy PIC interrupts on all the cpu's
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
powerpc/perf_events: Fix call-graph recording, add perf_arch_fetch_caller_regs
perf top: Add missing initialization to zero
perf probe: Use original address instead of CU-based address
perf probe: Fix offset to allow signed value
perf top: Improve the autosizing of column lenghts
perf probe: Fix need_dwarf flag if lazy matching is used
perf probe: Fix probe_point buffer overrun
Presently the TLB wiring code depends on MMUCR.URB for working out where
to place the wired entry, but fails to take the replacment counter in to
consideration. This fixes up the wiring logic and ensures that wired
entries remain so.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The mandatory barriers (mb, rmb, wmb) are used even on uniprocessor
systems for things like ordering Normal Non-cacheable memory accesses
with DMA transfer (via Device memory writes). The current implementation
uses dmb() for mb() and friends but this is not sufficient. The DMB only
ensures the relative ordering of the observability of accesses by other
processors or devices acting as masters. In case of DMA transfers
started by writes to device memory, the relative ordering is not ensured
because accesses to slave ports of a device are not considered
observable by the DMB definition.
A DSB is required for the data to reach the main memory (even if mapped
as Normal Non-cacheable) before the device receives the notification to
begin the transfer. Furthermore, some L2 cache controllers (like L2x0 or
PL310) buffer stores to Normal Non-cacheable memory and this would need
to be drained with the outer_sync() function call.
The patch also allows platforms to define their own mandatory barriers
implementation by selecting CONFIG_ARCH_HAS_BARRIERS and providing a
mach/barriers.h file.
Note that the SMP barriers are unchanged (being DMBs as before) since
they are only guaranteed to work with Normal Cacheable memory.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L2x0 cache controllers need to explicitly drain their write buffer
even for Normal Noncacheable memory accesses.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces the outer_cache_fns.sync function pointer together
with the OUTER_CACHE_SYNC config option that can be used to drain the
write buffer of the outer cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To avoid #include collisions with subsequent patches in the series, this
patch moves the outer_cache definitions to a separate asm/outercache.h
file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Yanko's GA-MA78GM-S2H (BIOS F11) reports the following resource in a PCI
host bridge _CRS:
[07] 32-Bit DWORD Address Space Resource
Min Relocatability : MinFixed
Max Relocatability : MaxFixed
Address Minimum : CFF00000 (_MIN)
Address Maximum : FEBFFFFF (_MAX)
Address Length : 3EE10000 (_LEN)
This is invalid per spec (ACPI 4.0, 6.4.3.5) because it's a fixed size,
fixed location descriptor, but _LEN != _MAX - _MIN + 1.
Based on https://bugzilla.kernel.org/show_bug.cgi?id=15480#c15, I think
Windows handles this by truncating the window so it fits between _MIN and
_MAX. I also verified this by modifying the SeaBIOS DSDT and booting
Windows 2008 R2 with qemu.
This patch makes Linux truncate the window, too, which fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=15480
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With insert_resource_conflict(), we can learn what the actual conflict is,
so print that info for debugging purposes.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_claim_resource() already prints more detailed error messages, so these
are really redundant.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_claim_resource() already prints more detailed error messages, so these
are really redundant.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Power Gates must to be always enabled.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the using of Bad Block Table is not constantly a good behave
I had made it configurable.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to imx31 reference manual the signal from external low
frequency clock is sent to RTC clock.
The patch makes redundant the previously defined mxc_rtc clock.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'sh/for-2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Silence unintialized variable warnings in dwarf unwinder.
sh: Tidy up a couple of section mismatches.
sh: Fix build after dynamic PMB rework
sh: Replace unsafe manipulation of MMUCR
sh: Flush ITLB too in PTEAEX's flush_tlb_page()
sh64: Remove long unused mid_sched macro
SH: remove superfluous warning from the serial driver
SH: fix SCIFA SCASCR register bit definitions
serial: sh-sci: fix SH-Mobile SH breakage
sh: Add watch-dog register address for SH7722/SH7723/SH7724
sh: ms7724: Add tiny-document for sound
sh: mach-ecovec24: Add i2c_put_adapter on sh_eth_init
Fix two bugs with the kernel image compression:
1) reset the bss section of the compressed vmlinux
2) clear the high half of the registers for 64 bit early enough
for the decompression step
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 024914477e "memcg: move charges of anonymous
swap" revealed that the 1 byte and 2 byte cmpxchg is currently broken:
arch/s390/include/asm/system.h: Assembler messages:
arch/s390/include/asm/system.h:241: Error: junk at end of line: `(%r5)'
make[1]: *** [mm/page_cgroup.o] Error 1
make[1]: *** Waiting for unfinished jobs....
It turned out that commit 987bcdacb1 ([S390] use
inline assembly contraints available with gcc 3.3.3) broke the inline assembly.
The or operands are now in constraint 3 and 4 instead of 2 and 3.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The intermediate lowcore for CONFIG_SMP is allocated using a call to
__alloc_bootmem() with a goal of 0. That however doesn't guarantee that
the allocated piece of memory is below 2GB.
Instead we should call __alloc_bootmem_low().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To save the registers for all CPUs a sigp "store status" is done that
stores the registers to address absolute zero. To access storage at
absolute zero, normally the address of the prefix register of the
accessing CPU has to be used. This does not work when large pages are
active (currently only under LPAR). In order to fix that problem,
instead of memcpy memcpy_real is used, which switches to real mode
where prefixing works.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
"Input: add KEY_WPS_BUTTON definition" introduced
a generic keycode for WPS input events.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Commit "Input: add KEY_WPS_BUTTON definition"
added a generic keycode for WPS button.
Let's use it, instead of "F1" mapping.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The parent rb_node needs to be initialized to shut up the compiler, even
though we're unlikely to ever hit this issue at run time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
select_idle_routine() and register_sh_pmu() both needed their annotations
fixed up to silence section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_pmb_entry() is now only used by a function that is wrapped in #ifdef
CONFIG_PM, so wrap set_pmb_entry() in CONFIG_PM too.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Setting the TI in MMUCR causes all the TLB bits in MMUCR to be
cleared. Unfortunately, the TLB wired bits are also cleared when setting
the TI bit, causing any wired TLB entries to become unwired.
Use local_flush_tlb_all() which implements TLB flushing in a safer
manner by using the memory-mapped TLB registers. As each CPU has its own
PMB the modifications in pmb_init() only affect the local CPU, so only
flush the local CPU's TLB.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_tlb_page() can be used to flush TLB entries that map executable
pages. Therefore, we need to ensure that the ITLB is also flushed in
local_flush_tlb_page().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
interruptible_sleep_on() is referenced for use in the mid_sched macro
which is not used anywhere. Remove reference and macro as well as the
comment which appears to belong with them.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
i2c_put_adapter is needed after i2c_get_adapter
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 3f6da39053
(perf: Rework and fix the arch CPU-hotplug hooks) broke suspend to
RAM on my HP nx6325 (and most likely on other AMD-based boxes too)
by allowing amd_pmu_cpu_offline() to be executed for CPUs that are
going offline as part of the suspend process. The problem is that
cpuhw->amd_nb may be NULL already, so the function should make sure
it's not NULL before accessing the object pointed to by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a warning when booting 2.6.34-rc2:
[ 26.619814] ------------[ cut here ]------------
[ 26.624604] WARNING: at fs/proc/generic.c:316 __xlate_proc_name+0xac/0xc0()
[ 26.631555] name 'on/off button'
[ 26.634753] Modules linked in:
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The function locomo_m62332_senddata sends a three byte i2c message to
a M62332 DAC. This entire function is guarded with a spin_lock_irqsave
at the start of the function and a spin_unlock_irqrestore at the end.
As each byte is transferred, the i2c ACK from the DAC is checked.
Currently, if the ACK is missing the function simply returns without
the unlock. It also leaves the i2c bus in an invalid state since the
last byte transferred did not have a "stop" condition and leave the
bus idle.
Fix this by adding an exit path using goto.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The locomo spi registers are all defined in locomo.h as offsets
from the first spi register LOCOMO_SPI (0x60), which is itself
an offset from the locomo base address. To correctly access
these registers LOCOMO_SPI must always be included in the
address calculation.
There are two places in locomo.c where this is not done. The
first one, in locomo_suspend, actually results in a write to
LOCOMO_ST instead of LOCOMO_SPICT. The second is in __locomo_probe
and results in a write to LOCOMO_MCSX2 instead of LOCOMO_SPIIE.
Fix these by including LOCOMO_SPI in the calculation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
sharpsl_pm.c actually depends on max1111 driver being built-in when
not using legacy ssp code.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
One to many close parens.
In file included from arch/arm/include/asm/page.h:202,
from include/linux/mm_types.h:15,
from include/linux/sched.h:63,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function 'virt_to_bus':
arch/arm/include/asm/memory.h:214: error: expected ';' before ')' token
arch/arm/include/asm/memory.h:214: error: expected statement before ')' token
arch/arm/include/asm/memory.h: In function 'bus_to_virt':
arch/arm/include/asm/memory.h:219: error: expected ';' before ')' token
arch/arm/include/asm/memory.h:219: error: expected statement before ')' token
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Currently c1e_idle returns true for all CPUs greater than or equal to
family 0xf model 0x40. This covers too many CPUs.
Meanwhile a respective erratum for the underlying problem was filed
(#400). This patch adds the logic to check whether erratum #400
applies to a given CPU.
Especially for CPUs where SMI/HW triggered C1e is not supported,
c1e_idle() doesn't need to be used. We can check this by looking at
the respective OSVW bit for erratum #400.
Cc: <stable@kernel.org> # .32.x .33.x
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100319110922.GA19614@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix compile errors in dma-mapping-common.h
alpha: remove trailing spaces in messages
alpha: use __ratelimit
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Remove IOMMU_VMERGE config option
powerpc: Fix swiotlb to respect the boot option
powerpc: Do not call prink when CONFIG_PRINTK is not defined
powerpc: Use correct ccr bit for syscall error status
powerpc/fsl-booke: Get coherent bit from PTE
powerpc/85xx: Make sure lwarx hint isn't set on ppc32
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The description says:
Cause IO segments sent to a device for DMA to be merged virtually
by the IOMMU when they happen to have been allocated contiguously.
This doesn't add pressure to the IOMMU allocator. However, some
drivers don't support getting large merged segments coming back
from *_map_sg().
Most drivers don't have this problem; it is safe to say Y here.
It's out of date. Long ago, drivers didn't have a way to tell IOMMUs
about their segment length limit (that is, the maximum segment length
that they can handle). So IOMMUs merged as many segments as possible
and gave too large segments to drivers.
dma_get_max_seg_size() was introduced to solve the above
problem. Device drives can use the API to tell IOMMU about the maximum
segment length that they can handle. In addition, the default limit
(64K) should be safe for everyone.
So this config option seems to be unnecessary.
Note that this config option just enables users to disable the virtual
merging by default. Users can still disable the virtual merging by the
boot parameter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc initializes swiotlb before parsing the kernel boot options so
swiotlb options (e.g. specifying the swiotlb buffer size) are ignored.
Any time before freeing bootmem works for swiotlb so this patch moves
powerpc's swiotlb initialization after parsing the kernel boot
options, mem_init (as x86 does).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When printk() is disabled (CONFIG_PRINTK) at menu item
General setup
-> Configure standard kernel features (for small systems)
-> Enable support for printk
then there should be no printk() calls at all.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc implementations of syscall_get_error and
syscall_set_return_value should use CCR0:S0 (0x10000000) for testing
and setting syscall error status. Fortunately these APIs don't seem
to be used at the moment.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The commit c186caca3d leads to the
following errors with CONFIG_ALPHA_{TSUNAMI, TITAN, RAWHIDE, MARVEL}:
/home/fujita/git/linux-2.6/include/asm-generic/dma-mapping-common.h: In
function `dma_map_sg_attrs':
/home/fujita/git/linux-2.6/include/asm-generic/dma-mapping-common.h:49:
error: implicit declaration of function `for_each_sg'
/home/fujita/git/linux-2.6/include/asm-generic/dma-mapping-common.h:50:
error: syntax error before "kmemcheck_mark_initialized"
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Replace open-coded rate limiting logic with __ratelimit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (96 commits)
Blackfin: stop cleaning include/asm/asm-offsets.h
Blackfin: scale calibration when cpu freq changes
Blackfin: eat spurious space in asm/dpmc.h
Blackfin: fix anomaly 283 handling with exact hardware error
Blackfin: bf537-stamp: add example ADXL346 orientation resources
Blackfin: bf537-stamp: add example AD2S1210 IIO resources
Blackfin: don't support keypad wakeup from hibernate
Blackfin: bf537-stamp: add example AD7416 IIO resources
Blackfin: bf537-stamp: add example ADP8860 backlight/led resources
Blackfin: bf537-stamp: add example AD7414 temp sensor resources
Blackfin: rename AD1836 to AD183X in board files
Blackfin: bf537-stamp: add example AD2S120x resources
Blackfin: add support for the on-chip MAC status interrupts
Blackfin: asm/page.h: pull in asm-generic headers
Blackfin: mark gpio lib functions static
Blackfin: bf537-stamp: add example ADAU1361 resources
Blackfin: GPIO: implement to_irq handler
Blackfin: bf537-stamp: add example ADP122/ADP150 power regulator resources
Blackfin: bf537-stamp: add example AD2S90 resources
Blackfin: bf537-stamp: add example AD5398 power regulator resources
...
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
ARM/OMAP: Remove the +x bit from a couple of source files
omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values
OMAP4: fix temporary hacks that break multi-omap PM
OMAP2: cpu_is_omap2*: fix compile-time removal of unused code
omap3: pandora: add missing i2c3 board_info
omap: mach-omap2/io.c: fix function declarations
omap: Fix gpio_resume_after_retention
omap3: Fix support for the LEDs connected to GPIO outputs on IGEP v2board
omap: Checkpatch cleanup for blizzard.h
omap: pass the reboot command to the boot loader
omap2/3/4: mailbox: remove compiler warning
OMAP2: serial.c: Fix number of uarts in early_init
omap: Enable PM_RUNTIME in defconfigs to avoid USB compile errors
omap2: Update n8x0 defconfig to test multi-omap and DMA api changes
omap2: add USB initialization for tusb6010
omap4: Fix build break by moving omap_smc1 into a separate .S
omap2/3/4: ehci: avoid compiler error with touchbook
omap3: Fix compile for Touch Book early_param
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (27 commits)
microblaze: entry.S use delay slot for return handlers
microblaze: Save current task directly
microblaze: Simplify entry.S - save/restore r3/r4 - ret_from_trap
microblaze: PCI early support for noMMU system
microblaze: Fix dma alloc and free coherent dma functions
microblaze: Add consistent code
microblaze: pgtable.h: move consistent functions
microblaze: Remove ancient Kconfig option for consistent mapping
microblaze: Remove VMALLOC_VMADDR
microblaze: Add define for ASM_LOOP
microblaze: Preliminary support for dma drivers
microblaze: remove trailing space in messages
microblaze: Use generic show_mem()
microblaze: Change temp register for cmdline
microblaze: Preliminary support for dma drivers
microblaze: Move cache function to cache.c
microblaze: Add support from PREEMPT
microblaze: Add support for Xilinx PCI host bridge
microblaze: Enable PCI, missing files
microblaze: Add core PCI files
...
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (35 commits)
perf: Fix unexported generic perf_arch_fetch_caller_regs
perf record: Don't try to find buildids in a zero sized file
perf: export perf_trace_regs and perf_arch_fetch_caller_regs
perf, x86: Fix hw_perf_enable() event assignment
perf, ppc: Fix compile error due to new cpu notifiers
perf: Make the install relative to DESTDIR if specified
kprobes: Calculate the index correctly when freeing the out-of-line execution slot
perf tools: Fix sparse CPU numbering related bugs
perf_event: Fix oops triggered by cpu offline/online
perf: Drop the obsolete profile naming for trace events
perf: Take a hot regs snapshot for trace events
perf: Introduce new perf_fetch_caller_regs() for hot regs snapshot
perf/x86-64: Use frame pointer to walk on irq and process stacks
lockdep: Move lock events under lockdep recursion protection
perf report: Print the map table just after samples for which no map was found
perf report: Add multiple event support
perf session: Change perf_session post processing functions to take histogram tree
perf session: Add storage for seperating event types in report
perf session: Change add_hist_entry to take the tree root instead of session
perf record: Add ID and to recorded event data when recording multiple events
...
mpc52xx_gpt_wdt_setup is defined as 0, which causes the following build
failure with gcc 4.5, since it's built with -Werror.
arch/powerpc/platforms/52xx/mpc52xx_gpt.c:761:3: error: statement with no effect
Changing it to a static inline fixes the problem.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This implements a powerpc version of perf_arch_fetch_caller_regs
to get correct call-graphs.
It's implemented in assembly because that way we can be sure there isn't
a stack frame for perf_arch_fetch_caller_regs. If it was in C, gcc might
or might not create a stack frame for it, which would affect the number
of levels we have to skip.
With this, we see results from perf record -e lock:lock_acquire like
this:
# Samples: 24878
#
# Overhead Command Shared Object Symbol
# ........ .............. ................. ......
#
14.99% perf [kernel.kallsyms] [k] ._raw_spin_lock
|
--- ._raw_spin_lock
|
|--25.00%-- .alloc_fd
| (nil)
| |
| |--50.00%-- .anon_inode_getfd
| | .sys_perf_event_open
| | syscall_exit
| | syscall
| | create_counter
| | __cmd_record
| | run_builtin
| | main
| | 0xfd2e704
| | 0xfd2e8c0
| | (nil)
... etc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: anton@samba.org
Cc: linuxppc-dev@ozlabs.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100318050513.GA6575@drongo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
perf_arch_fetch_caller_regs() is exported for the overriden x86
version, but not for the generic weak version.
As a general rule, weak functions should not have their symbol
exported in the same file they are defined.
So let's export it on trace_event_perf.c as it is used by trace
events only.
This fixes:
ERROR: ".perf_arch_fetch_caller_regs" [fs/xfs/xfs.ko] undefined!
ERROR: ".perf_arch_fetch_caller_regs" [arch/powerpc/platforms/cell/spufs/spufs.ko] undefined!
-v2: And also only build it if trace events are enabled.
-v3: Fix changelog mistake
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1268697902-9518-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We shouldn't be always setting 'M' in the TLB entry since its reasonable
for somethings to be mapped non-coherent. The PTE should have 'M' set
properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500v1/v2 based chips will treat any reserved field being set in an
opcode as illegal. Thus always setting the hint in the opcode is
a bad idea.
Anton should be kept away from the powerpc opcode map.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ever for 32-bit with sufficiently high NR_CPUS, and starting
with commit 789d03f584 also for
64-bit, the statically allocated early fixmap page tables were
not covering FIX_OHCI1394_BASE, leading to a boot time crash
when "ohci1394_dma=early" was used. Despite this entry not being
a permanently used one, it needs to be moved into the permanent
range since it has to be close to FIX_DBGP_BASE and
FIX_EARLYCON_MEM_BASE.
Reported-bisected-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=14487
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <stable@kernel.org> # [as far back as long as it still applies]
LKML-Reference: <4B9E15D30200007800034D23@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar reported that with the recent changes of not
statically blocking IRQ0_VECTOR..IRQ15_VECTOR's on all the
cpu's, broke an AMD platform (with Nvidia chipset) boot when
"noapic" boot option is used.
On this platform, legacy PIC interrupts are getting delivered to
all the cpu's instead of just the boot cpu. Thus not
initializing the vector to irq mapping for the legacy irq's
resulted in not handling certain interrupts causing boot hang.
Fix this by initializing the vector to irq mapping on all the
logical cpu's, if the legacy IRQ is handled by the legacy PIC.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
[ -v2: io-apic-enabled improvement ]
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1268692386.3296.43.camel@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 4e6d488af3 either missed out the
following machine files or somehow managed to clash between merges.
Fixup the three files missing the second parameter to addruart macro
to allow them to build.
Fixes the following warnings in arch/arm/kernel/debug.c:
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:167: Error: too many positional arguments
arch/arm/kernel/debug.S:183: Error: too many positional arguments
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The decleration of error() as static in the platform specific uncompress
code in arch/arm/plat-samsung/include/plat/uncomopress.h causes the build
of the uncompressor to break. Remove it, as it is no longer needed.
arch/arm/boot/compressed/decompress.o: In function `gunzip':
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:67: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:73: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:80: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:95: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:152: undefined reference to `error'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reset period_ns and duty_ns values in suspend handler to avoid skip of
configuration if same values passed to pwm_config;
Restore invertion bit in resume handler.
Without this patch PWM works incorrectly after resume from suspend.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch/arm/boot/compressed/decompress.o: In function `do_decompress':
decompress.c:(.text+0x26e8): undefined reference to `error'
decompress.c:(.text+0x2760): undefined reference to `error'
decompress.c:(.text+0x27d8): undefined reference to `error'
decompress.c:(.text+0x2824): undefined reference to `error'
decompress.c:(.text+0x28f0): undefined reference to `error'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is now changed to PLAT8250_DEV_PLATFORM (= 0), because
it's the only port that's going to be initialized in
Zoom 2/3 boards.
So, it doesn't make sense to keep the hardcoded 3 value anymore.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
This is useless, since in Zoom2/3 boards, the ports aren't even
physically accessible.
They must be explicitly initted in the board-zoom2.c, board-zoom3.c
and board-3630sdp.c files instead.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
As we have a struct device populated at the time we are
printing the errors, using dev_* macros makes more sense,
as could give a better idea where the error/warning came from.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
This is for protecting a wrong mapping attempt of a zero-based
physical address.
The result is that, no serial port will be attempted to be mapped.
Also add an additional protection for NULL clocks before attempting
to enable them (if above condition applies)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
ARMv5T and earlier require that a ldm {}^ instruction is not followed
by an instruction that accesses banked registers. This patch restores
the nop that was lost in commit b86040a59f.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To support SMP platforms, KGDB requires the architecture backend to
implement the kgdb_roundup_cpus function.
This patch, taken against 2.6.33, implements the function for ARM based
on the MIPS port.
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Jean-Michel Hautbois <jhautbois@gmail.com>
Cc: KGDB Mailing List <kgdb-bugreport@lists.sourceforge.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
