The Freescale PCI-e RC poses as a transparent bridge, but does not
implement the IO_BASE or IO_LIMIT registers in the config space. This
means that the code which initializes the bridge resources ends up
setting the IO resources erroneously. Add quick_fsl_pcie_transparent()
to handle this.
This change sets RC of mpc8641 to be a transparent bridge
for legacy I/O access and initializes the RC bridge resources
from the device tree.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In pcibios_fixup_bus(), bridges that are subordinate
to transparent bridges were still relocating their
IORESOURCE_IO and IO_RESOURCE_MEM start and end values.
Fix this by preventing the transparent bridge from
relocating the start and end values, thus allowing the
subordinate non-transparent bridge full molestation rights.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set IDE in ULI1575 to not 100% native mode, which forces
the IDE driver to probe the irq itself.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We check the Link Training and State Status register to make sure we
are at least at the L0 state.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hose->bus_offset is only used for PCI config cycles and the 52xx PCI
config code doesn't actually ever set bus_offset to a non-zero value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSI108 code and the 32 bit powermac and chrp platforms
have dependency on PCI that is not easy or desirable to get rid
of.
The easiest fix is to always select CONFIG_PCI if one of those
platforms is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cores used in the MPC82xx/83xx/86xx embedded controllers are very similar
to those in the 32 bit general-purpose processors, so it makes sense to
treat them as the same CPU family.
Choosing between the embedded platforms and the multiplatform code is
now done in the platform menu, but functionally everything stays the
same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all the world is an i386. Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer. Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.
Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely. In fact, ARM already had that, but called it
sys_arm_sync_file_range. Move it to fs/sync.c and rename it, then implement
the needed compatibility routine. And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.
Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2e60161337 split up
arch/powerpc/boot/of.c so that some OF functions can be used on
platforms that don't want to use the overall OF platform boot code.
This is useful on things like PReP which can have an OF implementation
which is useful for debugging output, but inadequate for booting.
However, that commit didn't export quite enough things to make a
usable OF console on a non-OF system. In particular, the device tree
manipulation performed to initialize the OF console code must
explicitly use the OF device tree, rather than the flattened device
tree, even if the system is otherwise booting using a flattened device
tree. This makes it so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 3d5134ee83 left debugging turned on
in arch/powerpc/kernel/pci_64.c. This turns it off again.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently iSeries will recalibrate the cputime_factors in the first
settimeofday() call.
It seems the reason for doing this is to ensure a resaonable time delta after
time_init(). On current kernels (with udev), this call is made 40-60 seconds
into the boot process, by moving it to a late initcall it is called
approximately 5 seconds after time_init() is called. This is sufficient to
recalibrate the timebase.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for storage devices to the device probe code.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add storage driver core support for the PS3.
PS3 storage devices are a special kind of PS3 system bus device.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Preallocate 256 KiB of bootmem memory for the PS3 FLASH ROM storage driver.
This can be disabled by passing `ps3flash=off' on the kernel command line.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 uses the kernel's hotplug memory support, so make sure it is
always enabled when building for PS3.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the convenience of custom platform code make the powerpc
bootwrapper typdef kernel_entry_t global in scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes the constantness of the powerpc bootwrapper's console_ops.write
routine. Allows printing of constant strings.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for the 'll' (long long) printf qualifier in the powerpc zImage
bootwrapper. This is useful for bootwrapper debugging on 64 bit platforms.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add signed types to the powerpc zImage bootwrapper. These are needed by the
PS3 hcall interface.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove references to pSeries and OpenFirmware in the __secondary_hold
usage comment. __secondary_hold is a generic routine and can be used
by other platforms.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a printout of the params value to early_init_devtree.
This value is handy to have for comparison when debugging the
bootwrapper code.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the inline asm with bitops in the PS3 interrupt
chip mask routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the PS3 static symbols node to ppe_id and cpu to thread_id
to clarify usage.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add routines to probe devices present on the system
and to register those devices with the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the ps3fb device from a platform device to a PS3 system bus device.
Fix the remove and shutdown methods to support kexec and to make ps3fb a
loadable module.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 vuart updates to reflect the new PS3 unified device support.
- Move vuart devices to the PS3 system bus.
- Replace use of ps3_vuart_port_device with ps3_system_bus_device.
- Make the PS3 vuart bus driver a loadable module.
- Add remove() and shutdown() routines.
- Move ps3_vuart_work into ps3_vuart_port_priv.tx_list.
- Remove redundant spinlock ps3_vuart_work.lock.
- No longer free ps3_vuart_port_device.priv on shutdown.
- Cleanup Kconfig defs.
- Export symbols needed for modular port drivers.
- Arrange to use port numbers found in repository.
- Fix bugs in ps3_vuart_read_async() and polled reading
- Cleanup handling of shared interrupt with ps3_vuart_bus_interrupt_get()
and ps3_vuart_bus_interrupt_put()
- Add more comments to vuart.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repository updates:
- Extract ps3_repository_find_bus() from ps3_repository_find_device(), as the
storage driver needs it.
- Make ps3_repository_find_device() return -ENODEV if a device is not found,
just like if a bus is not found.
- Add ps3_repository_read_vuart_sysmgr_port() and
ps3_repository_read_vuart_av_port() to get vuart port info.
- Add device enumeration routines ps3_repository_find_device() and
ps3_repository_find_devices().
- Cleanup debug routines.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add modinfo attribute to ps3_system_bus devices. Also make them all
children of the same ps3_system_bus 'device' so they appear in a
corresponding subdirectory under /sys/devices.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow userspace to automatically load modules, we need to hook up
uevent for ps3_system_bus devices. I've used the form 'ps3:%d' with
the ps3_match_id, since that's what we use for matching drivers.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework the PS3 system bus to unify device support.
- DMA region sizes must be a power of two
- storage bus DMA updates:
- Small fixes for the PS3 DMA core:
o fix alignment bug
o kill superfluous test
o indentation
o spelling
o export ps3_dma_region_{create,free}()
- ps3_dma_region_init():
o Add `addr' and `len' parameters, so you can create a DMA region that
does not cover all memory (use `NULL' and `0' to cover all memory).
This is needed because there are not sufficient IOMMU resources to have
all DMA regions cover all memory.
o Uninline
- Added remove and shutdown routines to all drivers.
- Added loadable module support to all drivers.
- Added HV calls for iopte management (needed by sound driver).
Signed-off-by: MOKUNO Masakazu <mokuno@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixup the core platform parts needed for kexec to work on the PS3.
- Setup ps3_hpte_clear correctly.
- Mask interrupts on irq removal.
- Release all hypervisor resources.
- Create new routine ps3_shutdown_IRQ()
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This just moves the definitions of the PS3 chip_mask routines up
above the irq setup routines. This change is needed for the
kexec updates that follow. Also adds some inline documentation
to the routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix some PS3 build warnings reported by `make C=1'. You need to
install sparse:
git://git.kernel.org/pub/scm/devel/sparse/sparse.git
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use ioremap_flags() to map SPU regions as non-guarded.
Change the use of _ioremap() to ioremap_flags().
CC: Arnd Bergmann <arnd.bergmann@de.ibm.com>
CC: Masato Noguchi <Masato.Noguchi@jp.sony.com>
CC: Takao Shinohara <shin@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 debug routines from using the GCC specific
'__attribute__ ((unused))' to the preprocessor macro
__maybe_unused.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the PS3 static symbol virqs to ps3_ipi_virqs to aid in
debugging.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a shutdown method to spu_sysdev_class to allow proper spu resource
cleanup on system shutdown. This is needed to support kexec on the PS3
platform.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug which can cause corruption of the floating-point state
on return from a signal handler. If we have a signal handler that has
used the floating-point registers, and it happens to context-switch to
another task while copying the interrupted floating-point state from the
user stack into the thread struct (e.g. because of a page fault, or
because it gets preempted), the context switch code will think that the
FP registers contain valid FP state that needs to be copied into the
thread_struct, and will thus overwrite the values that the signal return
code has put into the thread_struct.
This can occur because we clear the MSR bits that indicate the presence
of valid FP state after copying the state into the thread_struct. To fix
this we just move the clearing of the MSR bits to before the copy. A
similar potential problem also occurs with the Altivec state, and this
fixes that in the same way.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Consider the prototype for gettimeofday():
int gettimofday(struct timeval *tv, struct timezone *tz);
Although it is valid to call with /either/ tv or tz being NULL, and
the C version of sys_gettimeofday() supports this, the current version
of gettimeofday() in the VDSO will SEGV if called with a NULL tv.
This adds a check for tv being NULL so that it doesn't SEGV.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the g5_defconfig with default settings.
This is to keep things up to date, and specifically to ensure that the
CONFIG_MACINTOSH_DRIVERS option is enabled. This also turns on
CONFIG_MSI.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Power machines supporting VRMA, Kexec/Kdump does not work.
VRMA (virtual real-mode area) means that accesses with IR/DR = 0
(i.e. the MMU "off") actually still go through the hash table,
using entries put there by the hypervisor.
This means that when we clear out the hash table on kexec, we need to
make sure these entries are left untouched.
This also adds plpar_pte_read_raw() on the lines of
plpar_pte_remove_raw().
Signed-off-by : Sachin Sant <sachinp@in.ibm.com>
Signed-off-by : Mohan Kumar M <mohan@in.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some of the PPC970 based systems, interrupt would be distributed to
offline cpus also even when booted with "maxcpus=1". So check whether
cpu online map and cpu present map are equal or not. If they are equal
default_distrib_server is used as interrupt server otherwise boot cpu
(default_server) used as interrupt server.
In addition to this, if an interrupt is assigned to a specific cpu (ie
smp affinity) and if that cpu is not online, the earlier code used to
return the default_distrib_server as interrupt server. This
introduces an additional parameter to the get_irq function, called
strict_check. Based on this parameter, if the cpu is not online
either default_distrib_server or -1 is returned.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On pSeries the firmware features are not setup until ppc_md.init_early,
so we can't do the firmware feature sections fixups till after this.
Currently firmware feature sections is only used on iSeries which inits
the firmware features much earlier. This is a bug in waiting on
pSeries.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For POWERPC, stolen time accounts for cycles lost to the hypervisor or
PURR cycles attributed to the other SMT thread. Hence, when a PURR is
available, we should still calculate stolen time, irrespective of being
virtualised.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Specifying 'console=ttyMM0' on the cmdline for the prmpc2800 is no
longer necessary.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a Marvell MPSC (serial controller) port is the specified
/chosen/stdout-path device, call 'add_preferred_console()' so the user
doesn't have to specify a 'console=ttyMMx' cmdline argument.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds irq_create_direct_mapping(). This routine is
an alternative to irq_create_mapping(), for irq controllers that
can use linux virq numbers directly as hardware numbers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A future patch will need the logic at the end of irq_create_mapping()
which setups a virq and installs it in the irq_map. So split it out
into a new function irq_setup_virq().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Uninline virq_to_hw and export it so modules can use it. The alternative
would be to export the irq_map array instead, but it's an infrequently
called function, and keeping the array unexported seems considerably
cleaner.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The holly support currently has separate rules to wrap its device tree
with its zImage. This can now be done automatically without the extra
rules so update holly support to use the automatic feature.
Signed-off-by: Mark A. Greer <mgreer@mista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 2 config options that indicate whether the platform being built
has a device tree source file associated with it. Namely,
CONFIG_WANT_DEVICE_TREE and CONFIG_DEVICE_TREE. When CONFIG_WANT_DEVICE_TREE
is 'y' and CONFIG_DEVICE_TREE isn't an empty string, automatically wrap
the specified device tree with the zImage being built.
To achieve this, the 'dts' variable will only be set when the conditions
above are true. The changes to the zImage.initrd.% and zImage.% rules
cause the device tree to be wrapped when 'dts' is set; otherwise, they
will work as they previosly did (i.e., build a zImage with no device tree).
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Being able to selectively wrap a device tree with the zIimage at build
time has been deemed unnecessary, so this removes Makefile support for
that feature.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
cpu_purr_data is a per-cpu array used to account for stolen time on
partitioned systems. It used to be the case that cpus accessed each
others' cpu_purr_data, so each entry was protected by a spinlock.
However, the code was reworked ("Simplify stolen time calculation")
with the result that each cpu accesses its own cpu_purr_data and not
those of other cpus. This means we can get rid of the spinlock as
long as we're careful to disable interrupts when accessing
cpu_purr_data in process context.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With both generic rtc and powerpc timer suspend / resume code now in the
(powerpc.git) tree, powerpc platforms using the generic timer and enabling
power management will have timer.o linked in the kernel, which they don't
need. Moreover, it will likely WARN_ON(!ppc_md.get_rtc_time), save
zero-time and return no error on suspend...
As a possible solution we can choose not to build timer.o when RTC_CLASS
is enabled. However, I can imagine systems with 2 rtc's, one served by the
ppc-rtc, another one generic built as a module, in which case using the
ppc-rtc for suspend / resume will be impossible. Not to say, that such a
configuration would be ugly...
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Glue code to hook up the pata_platform on the PA Semi Electra eval board.
CFE sets up device tree entries for the IDE interface, with device type
'ide' and compatible field 'electra-ide'.
We unfortunately need to modify the resources before calling the generic
platform driver, since the device tree only has one register window in
it and the driver expects two. Adding this as an of_platform driver
instead doesn't give us any benefit, it just adds one more layer of
register/probe functions.
Since CONFIG_PATA_PLATFORM depends on CONFIG_EMBEDDED, add that as a
default for PPC_PASEMI.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the timer sysdev use mktime instead of rtc_tm_to_time,
since rtc_tm_to_time just calls mktime anyway, and this means we
don't have a dependency on rtc-lib.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this, when kexec-ing, we copy the code and start the slaves on
their journey to the next kernel's spin loop as soon as we copy the
kexec image into place.
The kernel doesn't know exactly which slaves are spinning in
kexec_wait. This allows us to pass more than max-cpus to the
next kernel. But it also means that we might leave some behind.
Moving the code here means they have the time it takes us to
clear the hash table to wake up and move on. Moving the code
any earlier would reuqire walking the image description to
search for the code, which could span multiple pages.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current ppc64_defconfig kernel fails to boot on iSeries, dying with:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc00000000071b258
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=32 iSeries
<snip>
NIP [c00000000071b258] .iSeries_src_init+0x34/0x64
LR [c000000000701bb4] .kernel_init+0x1fc/0x3bc
Call Trace:
[c000000007d0be30] [0000000000008000] 0x8000 (unreliable)
[c000000007d0bea0] [c000000000701bb4] .kernel_init+0x1fc/0x3bc
[c000000007d0bf90] [c0000000000262d4] .kernel_thread+0x4c/0x68
Instruction dump:
e922cba8 3880ffff 78840420 f8010010 f821ff91 60000000 e8090000 78095fe3
4182002c e922cb58 e862cbb0 e9290140 <e8090000> f8410028 7c0903a6 e9690010
Kernel panic - not syncing: Attempted to kill init!
This happens because some powermac code unconditionally sets
ppc_md.progress to NULL. This patch makes sure the powermac late
initcall is only run on powermac machines.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "is_exec" branch of the protection check in do_page_fault()
didn't do anything on 32-bit PowerPC. So if a userland program
jumps to a page with Linux protection flags "---p", all the tests
happily fall through, and handle_mm_fault() is called, which in
turn calls handle_pte_fault(), which calls update_mmu_cache(),
which goes flush the dcache to a page with no access rights.
Boom.
This fixes it.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch adds fragments caused by rh_alloc_align() back to free list, instead
of allocating the whole chunk of memory. This will greatly improve memory
utilization managed by rheap.
It solves MURAM not enough problem with 3 UCCs enabled on MPC8323.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards. This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.
- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property. This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect. Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY. This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself. This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
- The compatible properties on a number of nodes in the device
tree are insufficiently precise. In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter. The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense. The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the Holly device tree includes a bootargs property in
/chosen, which gives a commandline. This is somewhat inconvenient,
because it means an alternative default command line can't be given in
the kernel config - the value obtained from the dts via the
bootwrapper will always override CONFIG_CMDLINE.
This removes the command line from the dts, and instead puts the
same command line as a default in holly_defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The various cuboot platforms (i.e. pre-device tree aware u-boot for
83xx, 85xx and Ebony) share a certain amount of code for parsing the
boot parameters. To a certain extent that's inevitable, since they
platforms have different definitions of the bd_t structure. However,
with some macro work and a helper function, this patch improves the
situation a bit.
In the process, this fixes a bug on Ebony, which was incorrectly
handling the parameters passed form u-boot for the command line (the
bug was copied from 83xx and 85xx which have subsequently been fixed).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB. At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.
This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them. This should make the zImage and kernel more
robust to changes in firmware configuration. In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space. With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ebony_exit() function which resets the Ebony board should in fact
be common to most if not all 44x boards. This moves the function out
into 44x.c, renaming it, so it can be used by other 44x platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t"). On ppc32 we
also have such a typedef for the BATs ("BAT").
This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In arch/powerpc/mm/pgtable_32.c, the variable io_bat_index and the
macro is_power_of_4() no longer have any users. This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be. Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.
A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These old-fashioned IO mapping functions no longer have any callers in
code which remains relevant on arch/powerpc. Therefore, this removes
them from arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all OF-related code in the bootloader is contained in of.c.
of.c also provides the platform specific things necessary to boot on
an OF platform.
However, there are platforms (such as PReP) which can include an OF
implementation, but are not bootable as pure OF systems. For use by
such platforms, this patch splits out the low-level parts of the OF
code (call_prom() and various wrappers thereof) into a new oflib.c
file. In addition, the code related to bootwrapper console output via
OF are moved to a new ofconsole.c file. Both these files are included
in the wrapper.a library where they can be used by both full-OF and
partial OF platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A lot of the options in arch/powerpc/Kconfig deal with the CPU menu,
and my next patches add more to them. Moving them to a new
arch/powerpc/platforms/Kconfig.cputype file makes it easier to
follow.
There are no functional changes in here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a
bad state, whereas killing the entire process group would allow for
the application to restart, or be otherwise handled, and makes it very
obvious that something has gone wrong.
This change allows the entire process group to be taken down, rather than
just the one thread.
lightly tested on powerpc
Signed-off-by: Will <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).
This enables that to work properly on P6.
This just involves setting a bit in the CAS structure as well as the
VPA. To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA. Then call H_CEDE.
The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.
Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves things around a little bit in the new common signal.c
and signal.h files to remove the last #ifdef in the middle of the
common do_signal().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
set_dabr() and thread.dabr exist on 32 bits as well nowadays (they
actually may do something even, depending on what CPU you have).
So this removes the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for creating signal frames was still duplicated and split
in strange ways between 32 and 64 bits, including the SA_ONSTACK
handling being in do_signal on 32 bits but inside handle_rt_signal
on 64 bits etc...
This moves the 64 bits get_sigframe() to the generic signal.c,
cleans it a bit, moves the access_ok() call done by all callers to
it as well, and adapts/cleanups the 3 different signal handling cases
to use that common function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc signal code still had some obsolete freezer bits that
have long been removed from x86 (it's now done in generic code).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
do_signal has exactly the same behaviour on 32bit and 64bit and 32bit
compat on 64bit for handling 32bit signals. Consolidate all these
into one common function in signal.c. The only odd left over is
the try_to_free in the 32bit version that no other architecture has
in mainline (only in i386 for some odd SuSE release). We should
probably get rid of it in a separate patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
restore_sigmask is exactly the same on 32 and 64bit, so move it to
common code. Also move _BLOCKABLE to signal.h to avoid defining it
multiple times.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sys_sigaltstack is the same on 32bit and 64 and we can consolidate it
to signal.c. The only difference is that the 32bit code uses ints
for the unused register paramaters and 64bit unsigned long. I've
changed it to unsigned long because it's the same width on 32bit.
(I also wonder who came up with this awkward calling convention.. :))
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the code in signal_32.c and signal_64.c for handling
syscall restart into a common signal.c file and converge around a single
implementation that is based on the 32 bits one, using trap, ccr
and r3 rather than the special "result" field for deciding what to do.
The "result" field is now pretty much deprecated. We still set it for
the sake of whatever might rely on it in userland but we no longer use
it's content.
This, along with a previous patch that enables ptracers to write to
"trap" and "orig_r3" should allow gdb to properly handle syscall
restarting.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the #ifdef CONFIG_PPC64 around setting the DABR.
The actual setting of the SPR inside of the set_dabr() function is dependent
on CONFIG_PPC64 || CONFIG_6xx but you can always provide a ppc_md hook to
override that. We should improve support for different HW breakpoints
facilities but this is a first step.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow ptrace to set dabr in the thread structure for both 32 and 64 bits,
though only 64 bits actually uses that field, it's actually defined in both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the gratuitous difference between 32 and 64-bit ptrace is
whether you can whack the MSR:FE0 and FE1 bits from ptrace. This
patch forbids it unconditionally. In addition, the 64-bit kernels
used to return the exception mode in the MSR on reads, but 32-bit
kernels didn't. This patch makes it return those bits on both.
Finally, since ptrace-ppc32.h and ptrace-ppc64.h are mostly empty now, and
since the previous patch made ptrace32.c no longer need the MSR_DEBUGCHANGE
definition, we just remove those 2 files and move back the remaining bits
to ptrace.c (they were short lived heh ?).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows a ptracer to write to the "trap" and "orig_r3" words
of the pt_regs.
This, along with a subsequent patch to the signal restart code, should
enable gdb to properly handle syscall restarting after executing a separate
function (at least when there's no restart block).
This patch also removes ptrace32.c code toying directly with the registers
and makes it use the ptrace_get/put_reg() accessors for everything so that
the logic for checking what is permitted is in only one place.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CHECK_FULL_REGS() exist on both 32 and 64 bits, so there's no need
to make it conditional on CONFIG_PPC32.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This folds back the ptrace-common.h bits back into ptrace.c and removes
that file. The FSL SPE bits from ptrace-ppc32.h are folded back in as
well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc ptrace interface is dodgy at best. We have defined our
"own" versions of GETREGS/SETREGS/GETFPREGS/SETFPREGS that strangely
take arguments in reverse order from other archs (in addition to having
different request numbers) and have subtle issue, like not accessing
all of the registers in their respective categories.
This patch moves the implementation of those to a separate function
in order to facilitate their deprecation in the future, and provides
new ptrace requests that mirror the x86 and sparc ones and use the
same numbers:
PTRACE_GETREGS : returns an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... There's a compat version
for 32 bits that returns a 32 bits compatible
pt_regs (44 uints)
PTRACE_SETREGS : sets an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... Some registers cannot be
written to and will just be dropped, this is the
same as with POKEUSR, that is anything above MQ
on 32 bits and CCR on 64 bits. There is a compat
version as well.
PTRACE_GETFPREGS : returns all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
PTRACE_SETFPREGS : sets all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
And two that only exist on 64 bits kernels:
PTRACE_GETREGS64 : Same as PTRACE_GETREGS, except there is no compat
function, a 32 bits process will obtain the full 64
bits registers
PTRACE_SETREGS64 : Same as PTRACE_SETREGS, except there is no compat
function, a 32 bits process will set the full 64
bits registers
The two later ones makes things easier to have a 32 bits debugger on a
64 bits program (or on a 32 bits program that uses the full 64 bits of
the GPRs, which is possible though has issues that will be fixed in a
later patch).
Finally, while at it, the patch removes a whole bunch of code duplication
between ptrace32.c and ptrace.c, in large part by having the former call
into the later for all requests that don't need any special "compat"
treatment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc ptrace code has some weirdness, like a ptrace-common.h file that
is actually ppc64 only and some of the 32 bits code ifdef'ed inside ptrace.c.
There are also separate implementations for things like get/set_vrregs for
32 and 64 bits which is totally unnecessary.
This patch cleans that up a bit by having a ptrace-common.h which contains
really common code (and makes a lot more code common), and ptrace-ppc32.h and
ptrace-ppc64.h files that contain the few remaining different bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The handling of PPC_PTRACE_GETFPREGS is broken on 32 bits kernel,
it will only return half of the registers. Since that call didn't
initially exist for 32 bits kernel (added recently), rather than
fixing it, let's just remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a "capabilities" file to spu contexts consisting of a
list of linefeed separated capability names. The current exposed
capabilities are "sched" (the context is scheduleable) and
"step" (the context supports single stepping).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for SPU single stepping. The single
step bit is set in the SPU when the current process is
being single-stepped via ptrace. The spu then stops and
returns with a specific flag set and the syscall exit code
will generate the SIGTRAP.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes unmap_vm_area static and a wrapper around a new
exported unmap_kernel_range that takes an explicit range instead
of a vm_area struct.
This makes it more versatile for code that wants to play with kernel
page tables outside of the standard vmalloc area.
(One example is some rework of the PowerPC PCI IO space mapping
code that depends on that patch and removes some code duplication
and horrible abuse of forged struct vm_struct).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Twiddle the copyright notices. Per current guidelines, the use
of the (C) or (c) in source code is deprecated.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 6 +++++-
arch/powerpc/platforms/pseries/eeh_cache.c | 3 ++-
arch/powerpc/platforms/pseries/eeh_driver.c | 6 +++---
3 files changed, 10 insertions(+), 5 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Track and report the number of times we read an all-1s value (0xff,
0xffff or 0xffffffff) from each device which is valid data, not
indicating EEH isolation.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 5 +++++
arch/powerpc/platforms/pseries/eeh_sysfs.c | 3 +++
include/asm-powerpc/pci-bridge.h | 1 +
3 files changed, 9 insertions(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maybe the type should have been char[] instead of __u8[]
in the first place, but this will do.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously, registering this early console would just result
in dropping early buffered printk output until a udbg_putc
was registered.
However, commit 69331af79c
clears the CON_PRINTBUFFER flag on the main console when a
CON_BOOT (early) console has been registered, resulting in
the buffered messages never being displayed to the user.
This fixes the problem by making sure we don't register udbg_console
on platforms that don't implement udbg_putc.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-cpu area(a) for the secondary CPU(s) isn't getting allocated
on old SMP powermacs that don't have the secondary CPU(s) listed in
the device tree, as per-cpu areas are now only allocated for CPUs in
the cpu_possible_map, and we aren't setting the bits for the secondary
CPU(s) until smp_prepare_cpus(), which is after per-cpu allocation.
Therefore this sets the bits for CPUs 1..3 in cpu_possible_map in
pmac_setup_arch, so they get per-cpu data allocated.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The COFF zImage (for booting oldworld powermacs) wasn't being built
correctly because the procedure descriptor in crt0.S for the zImage
entry point wasn't declared as .globl, and therefore wasn't getting
pulled in from wrapper.a by the linker. This adds the necessary
.globl statement.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The error path in spufs_fill_dir() is broken. If d_alloc_name() or
spufs_new_file() fails, spufs_prune_dir() is getting called. At this time
dir->inode is not set and a NULL pointer is dereferenced by mutex_lock().
This bugfix replaces spufs_prune_dir() with a shorter version that does
not touch dir->inode but simply removes all children.
Signed-off-by: Sebastian Siewior <bigeasy@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Nosched context sould never be scheduled out, thus we must not
deactivate them in spu_yield ever.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scc_sio.o should only be built if the txx9 serial driver is actually
built into the kernel.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
... and get rid of cpufreq_set_policy call that caused a build
failure due interfering commits.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We had a problem on a system with only dynamically allocated
PCI buses (using of_pci_phb_driver) in combination with libata.
This setup ended up having no "primary" phb, which means
that pci_io_base never got initialized and all IO port
numbers are 64 bit numbers, which is larger than the
PIO_MASK limit.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the race between checking for contexts on the runqueue and actually
waking them in spu_deactive and spu_yield.
The guts of spu_reschedule are split into a new helper called
grab_runnable_context which shows if there is a runnable thread below
a specified priority and if yes removes if from the runqueue and uses
it. This function is used by the new __spu_deactivate hepler shared
by preemption and spu_yield to grab a new context before deactivating
a specified priority and if yes removes if from the runqueue and uses
it. This function is used by the new __spu_deactivate hepler shared
by preemption and spu_yield to grab a new context before deactivating
the old one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sure the mapping_lock also protects access to the various address_space
pointers used for tearing down the ptes on a spu context switch.
Because unmap_mapping_range can sleep we need to turn mapping_lock from
a spinlock into a sleeping mutex.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In case spufs_fill_dir() fails only put_spu_context()
gets called for cleanup and the acquired mm_struct never gets freed.
Signed-off-by: Sebastian Siewior <bigeasy@linux.vnet.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously, closing a SPE gang that still has contexts would trigger
a WARN_ON, and leak the allocated gang.
This change fixes the problem by using the gang's reference counts to
destroy the gang instead. The gangs will persist until their last
reference (be it context or open file handle) is gone.
Also, avoid using statements with side-effects in a WARN_ON().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently spufs_mem_release and the mem file doesn't have any release
method hooked up, leading to leaks everytime is used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As noticed by David Woodhouse, it's currently possible to mount
spufs on any machine, which means that it actually will get
mounted by fedora.
This refuses to load the module on platforms that have no
support for SPUs.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc iommu code was refactored by Linas back in the 2.6.20 time
frame to map 4K pages from the generic code, but I had forgotten to go
back and fix my platform driver before submitting it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 9da82a6dee inadvertently
removed the platform override for zImage.coff to be generated
with pmaccoff. Rather than add a special makefile rule,
change the platform for which the wrapper platform uses
the special rules.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a thinko in the irq code, it uses IRQ_NONE to indicate no irq,
whereas it should be using NO_IRQ. IRQ_NONE is returned from irq
handlers to say "not handled".
As it happens they currently have the same value (0), so this is just for
future proof-ness.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 616883df78 request_irq was marked as
__must_check so we must... er... check it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the bootwrapper code for powerpc, we include HOSTCFLAGS into the
BOOTCFLAGS used for building the zImage wrapper code. Since the
wrapper code is not host code, this makes no sense. This patch
removes the use of HOSTCFLAGS here, instead including directly into
BOOTCFLAGS those flags from the normal kernel CFLAGS which also make
sense in the bootwrapper code.
In particular, this makes the bootwrapper use -msoft-float, preventing
the compiler from generating floating point instructions. Previously,
under some circumstances the compiler could generate floating point
instructions in the bootwrapper which would cause exceptions on
embedded CPUS which don't have floating point support.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This zImage is really just the stripped vmlinux, but it means that there
is one less special case for iSeries and also that the zImages will be
built for a combined kernel build that happens to include iSeries.
This zImage boots fine on legacy iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and so needs to include asm/smp.h so a UP build works.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and so needs to include asm/smp.h for a UP build to work.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent addition of assembler flags for 44x.c and ebony.c in the
bootwrapper to make them compile on certain toolchains was not correct
and could break other platforms. This patch switches to using a
compiler flag instead, which implies the appropriate assembler flag,
and also stops the compiler itself generating instructions which are
invalid for the platform in question.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 kernel didn't properly set/clear the TIF_SINGLESTEP
flag, causing return from syscalls to not SIGTRAP, thus executing
one more instruction before stopping again.
This fixes it. The ptrace code is a bit of a mess, and is overdue
for at least a -proper- 32/64 bits split and possibly more cleanups
but this minimum fix should be ok for 2.6.22
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The documentation for of_find_node_by_type() incorrectly refers to the
"name" parameter - it should be "type".
Also the behaviour when from == NULL is not really documented, fix that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix config warning related to select usage:
drivers/macintosh/Kconfig:117:warning: 'select' used by config symbol 'PMAC_APM_EMU' refers to undefined symbol 'SYS_SUPPORTS_APM_EMULATION'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mark pte_alloc_one_kernel as __init_refok to fix the following warning:
WARNING: arch/powerpc/mm/built-in.o(.text+0x1068): Section mismatch: reference to .init.text:early_get_page (between 'pte_alloc_one_kernel' and 'steal_context')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fix the following Section mismatch warnings in powerpc code.
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.data:mv643xx_eth_pd_devs from .text between 'mv643xx_eth_add_pds' (at offset 0x9ed2) and 'gg2_read_config'
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.data:mv643xx_eth_pd_devs from .text between 'mv643xx_eth_add_pds' (at offset 0x9ed6) and 'gg2_read_config'
WARNING: arch/powerpc/platforms/built-in.o - Section mismatch: reference to .init.text:note_scsi_host from __ksymtab between '__ksymtab_note_scsi_host' (at offset 0x8) and '__ksymtab_sys_ctrler'
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds. On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Unbreak lite5200 dts, which were broken by
5c1992f833
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some missing fixup for the removal of 4 level fixup header.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Sam's recent change in 7664709b44
broke things for us because we ended up with *(.text.*) before
*(.text), whereas previously *(.text) was first. This was
important because the start of the text section contains the
kernel entry point.
In fact, we don't need that *(.text.*) thing anymore and it
incorrectly matched .text.init.refok, thus putting it before
.text. .. ouch !
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pmc.c has:
#ifndef MMCR0_PMA0
#define MMCR0_PMA0 0
This one took a while to find. Unfortunately its the wrong define
(number 0 vs letter O). Its probably worth removing this override, since
if our includes get screwed up we will have the same (hard to debug)
failure.
Fix it simply for now, so that we can backport to stable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A number of cpu_table entries were missing the pmc_type field,
which means that the sysfs entries for the performance monitor
counters don't get created. This adds them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_call_function_map() was not safe against preemption to another
cpu: its test for removing self from map was outside the spinlock.
Rearrange it a little to fix that.
smp_call_function_single() was also wrong: now get_cpu() before
excluding self, as other architectures do.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fix:
mm/slab: fix section mismatch warning
mm: fix section mismatch warnings
init/main: use __init_refok to fix section mismatch
kbuild: introduce __init_refok/__initdata_refok to supress section mismatch warnings
all-archs: consolidate .data section definition in asm-generic
all-archs: consolidate .text section definition in asm-generic
kbuild: add "Section mismatch" warning whitelist for powerpc
kbuild: make better section mismatch reports on i386, arm and mips
kbuild: make modpost section warnings clearer
kconfig: search harder for curses library in check-lxdialog.sh
kbuild: include limits.h in sumversion.c for PATH_MAX
powerpc: Fix the MODALIAS generation in modpost for of devices
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (32 commits)
[POWERPC] Remove build warnings in windfarm_core
[POWERPC] Pass per-file CFLAGs for platform specific op codes
[POWERPC] Correct #endif comment
[POWERPC] Fix ppc_rtas_progress_show()
[POWERPC] Fix sed command lines for zlib source construction
[POWERPC] Specify GNUTARGET on $(AR) invocations
[POWERPC] Make sure device node type/name is not NULL on hot-added nodes
[POWERPC] Small fixes for the Ebony device tree
[POWERPC] Fix warning on UP
[POWERPC] cell_defconfig: Disable cpufreq and pmi
[POWERPC] Fix IO space on PCI buses created from of_platform
[POWERPC] Add spinlock to request_phb_iospace()
[POWERPC] Fix make rules for treeImage.initrd
[POWERPC] Remove warning in mpic.c
[POWERPC] Update pasemi_defconfig
[POWERPC] pasemi: CONFIG_GENERIC_TBSYNC no longer needed
[POWERPC] Update iseries_defconfig
[POWERPC] Wire up some more syscalls
[POWERPC] Fix bug adding properties with flatdevtree.c's ft_set_prop()
[POWERPC] Remove fixup_bigphys_addr() for arch/powerpc to avoid link error
...
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a result of compiling all of the wrapper files for every platform
now, the kernel build can fail for toolchains that don't support various
op codes by default. An example of this building a 7xx platform with
the ELD4.0 toolchain, is below:
/tmp/ccYjhJoL.s: Assembler messages:
/tmp/ccYjhJoL.s:42: Error: Unrecognized opcode: `mtdcr'
/tmp/ccYjhJoL.s:43: Error: Unrecognized opcode: `mfdcr'
make[1]: *** [arch/powerpc/boot/44x.o] Error 1
The following patch introduces additional CFLAGS for the 4xx specific
files and fixes the kernel compile.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up comment on two #endifs to match their #ifs.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
----
hash_utils_64.c | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes the warning
arch/powerpc/kernel/rtas-proc.c: In function 'ppc_rtas_progress_show':
arch/powerpc/kernel/rtas-proc.c:382: warning: the address of
'progress_led' will always evaluate as 'true'
by fixing the code to do what it presumably is meant to do.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Not every sed understands \+ so use the more portable * instead.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this, some versions of GNU ar fail to create
an archive index if the object files it is packing
together are of a different object format than ar's
default format (for example, binutils compiled to
default to 64-bit, with 32-bit objects).
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our device-tree unflattening code makes sure the name and type fields
of a device-node are not NULL. However, the code for dynamically
adding devices nodes which is used for pSeries hotplug for example
didn't do it, potentially causing crashes in some code that assume it
can always do things like strcmp on those.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch corrects a number of minor errors in the Ebony device tree:
- Missing (given as 0) cache sizes are added to the CPU node
- device_type properties are removed from nodes which don't
have a reasonably well defined device_type binding. This does require
a very small code change to locate the busses to be probed for
of_platform devices by 'compatible' instead of 'device_type'.
- A node is added for the SRAM controller
- The unit address of the small-flash node is adjusted to
correctly reflect the reg property.
- device_type values for the MAL and ZMII are updated to
reflected more up-to-date versions of the binding.
- An incorrect offset in the partition map for the large-flash
node is corrected.
- Some redundant values, already commented out are removed
entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pseries/pseries.h:24: warning: return type defaults to 'int'
arch/powerpc/platforms/pseries/pseries.h:25: warning: return type defaults to 'int'
arch/powerpc/platforms/pseries/pseries.h:24: warning: control reaches end of non-void function
arch/powerpc/platforms/pseries/pseries.h:25: warning: control reaches end of non-void function
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cpufreq using pmi is broken by a dependency issue, that
will be fixed in a seperate patch.
Bare-metal cpufreq is broken by hardware limitations.
As it was the only user, pmi is disabled as well.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the way of_platform_pci creates PCI host bridges such
that it uses request_phb_iospace() for mapping the IO ports, instead
of using the dynamic hotplug stuff. That guarantees the IO space
stays within the 2GB limit and thus doesn't break half of the legacy
drivers around.
Fixes a couple of warnings due to missing IO space while at it.
This patch is a temporary workaround for 2.6.22 before a more complete
rewrite of IO mappings is merged in 2.6.23
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
request_phb_iospace() can be called from different CPUs at init
time (at least with my next patch) and thus needs a spinlock.
As for the next patch, this is a temporary workaround for 2.6.22
issues until my rewrite of IO mappings is ready (for 2.6.23)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present attempting to build treeImage.initrd.* boot images will
fail, because make will select the treeImage.% rule which also matches
instead of the correct and more specific treeImage.initrd.% rule.
This patch corrects the problem by listing the more specific rule
first.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/mpic.c: In function 'mpic_request_ipis':
arch/powerpc/sysdev/mpic.c:1445: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update pasemi_defconfig, add new relevant drivers. Take out
CONFIG_PPC_PSERIES, it should't have been enabled in the first place.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current kernel implements proper TB sync, no need to keep GENERIC_TBSYNC
enabled.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ft_set_prop() from flatdevtree.c in the zImage wrapper will either
replace an existing property in the flat device tree, or add a new
property definiion if the given property isn't present.
However, when adding properties, it adds the property definition
immediately before the node's END_NODE tag, potentially after any
subnode definitions for the node. This confuses the kernel flat tree
parser in prom.c which assumes that all property definitions for a
node come before all subnode definitions.
This patch corrects ft_set_prop() so that it adds new properties
before the first subnode, instead of before the END_NODE tag.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use a completion instead of abusing a semaphore for hypervisor event
completion in viopath.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An allmodconfig on the current powerpc tree yields:
arch/powerpc/platforms/44x/Kconfig:41:warning: 'select' used by
config symbol '440GP' refers to undefined symbol 'IBM_NEW_EMAC_ZMII'
Hide the select until the driver exists.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove explicit phandles and move to using references that autogenerate the
phandles when needed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8541 CDS, MPC8544 DS, MPC8555 CDS, and MPC8568 MDS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8540 ADS, MPC8548 CDS, and MPC8560 ADS.
Also fixed up the size of the PCI node on MPC8560 ADS.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When an rheap is created, the caller can specify the alignment to use. In
rh_alloc_align(), if a free block is found that is the exact size needed
(including extra space for alignment), that configured alignment value is not
used to align the pointer. Instead, the default alignment is used. If the
default alignment is smaller than the configured alignment, then the returned
value will not be aligned correctly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We get the following warnings in various ARCH=powerpc builds:
WARNING: "ee_restarts" [arch/powerpc/kernel/built-in] is COMMON symbol
WARNING: "fee_restarts" [arch/powerpc/kernel/built-in] is COMMON symbol
WARNING: "htab_hash_searches" [arch/powerpc/mm/built-in] is COMMON symbol
WARNING: "next_slot" [arch/powerpc/mm/built-in] is COMMON symbol
WARNING: "mmu_hash_lock" [arch/powerpc/mm/built-in] is COMMON symbol
WARNING: "primary_pteg_full" [arch/powerpc/mm/built-in] is COMMON symbol
WARNING: "global_dbcr0" [arch/powerpc/kernel/built-in] is COMMON symbol
Switch to moving local symbols (except mmu_hash_lock which is global) and
space directive instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove CPU_FTR_NEED_COHERENT for MPC7448 (and single-core MPC86xx).
This prevents needlessly setting M=1 when not SMP.
Signed-off-by: James.Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This finally adds the PPC_PRPMC2800 Kconfig option, the board setup
code (the setup and reset functions) and the defconfig, to support the
Motorola PrPMC2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_cache_coherency() verifies that the cache coherency setting of
the kernel (CONFIG_NOT_COHERENT_CACHE) matches that left by the firmware,
as indicated by coherency-off device tree property.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD). The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.
Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala