In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.
This patch also adds code to use get_brgfreq() on QE chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is dangerous for an mpc52xx device driver to modify the port_config
register. If the driver is probed incorrectly, it will change the pin
IO configuration in ways which may not be compatible with the board.
port_config should be set up by the bootloader, or failing that, in
the platform setup code in arch/powerpc/platforms/52xx.
Also, modifying CDM registers directly can cause a race condition with
other drivers. Instead call a common routine to modify CDM settings.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert to use the class iteration api.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before transmission of the last word in PIO RX_ONLY mode rx+tx mode
is enabled:
/* prevent last RX_ONLY read from triggering
* more word i/o: switch to rx+tx
*/
if (c == 0 && tx == NULL)
mcspi_write_cs_reg(spi,
OMAP2_MCSPI_CHCONF0, l);
But because c is decremented after the test, c will never be zero and
rx+tx will not be enabled. This breaks RX_ONLY mode PIO transfers.
Fix it by decrementing c in the beginning of the various I/O loops.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix a glitch reported by lockdep in the spi_bitbang code: it needs to
consistently block IRQs when holding that spinlock.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a wifi module connected to the spi bus and got sometimes FIFO
overrun errors on the spi bus.
After some investigation i found that the driver loads the TCR (transmit
count) register before the RCR (receive count). When the transfer list is
not empty the atmel_spi_next_message is called while tx and rx are enabled.
As soon as the TCR is loaded, hardware starts transfer and causes a rx
fifo overrun because the RCR is not loaded yet.
Load the RCR before the TCR. After this patch the fifo overrun disapears
at out setup.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move global SPI regs_base and dma_ch to struct driver_data. Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing. Plus other minor
updates.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup and error handling
- add error handling in SPI bus driver with selecting clients
- use proper defines to access Blackfin MMRs
- remove useless SSYNCs
- cleaner use of portmux calls
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use new Blackfin portmux interface, add error handling.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial BF54x SPI support
- support BF54x SPI0
- clean up some code (whitespace etc)
- will support multiports in the future
- start using portmux calls
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status. In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible. The command sets are different, as
is the treatment of erasure. (FLASH needs explicit erasure, but
with EEPROM it's implicit.) Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow passing a bus number through the platform data for the S3C2410 SPI
GPIO driver. This is needed to support multiple SPI busses.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we specify an GPIO which cannot be used for the purpose, then assume
that the GPIO is not to be used and do not try and configure it. This can
be the case where the SPI bus is TX only.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the atmel_spi driver label GPIOs according to the device for which
they're acting as a chipselect. This way the debugfs dump of gpio state is
more informative.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tle62x0 driver was ignoring all read errors. This patch makes it
pass such errors up the stack, instead of returning bogus data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some error paths in txx9spi_probe wrongly return 0. This patch fixes them by
using the devres interfaces.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 49dce689ad, device_for_each_child
iteration hits the master device itself. Do not call spi_unregister_device()
for the master device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the SPI framework and drivers stop using class_device. Update docs
accordingly ... highlighting just which sysfs paths should be
"safe"/stable.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all QE SPI controllers are almost the same comparing to
MPC83xx's, thus let's use that driver for them.
Tested to work on MPC85xx in loopback mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shrink the runtime footprint of various SPI drivers:
- Move the probe() routine into the init section where practical,
using platform_driver_probe() to make that safe. This often saves
around 1KB. Using platform_driver_probe() can also be a correctness
fix, if the probe routine is already marked __init but the driver
struct keeps a dangling pointer to it after init section removal.
- Likewise move remove() routines into the exit sections.
These changes would be inappropriate iff the platform devices were
actually hotpluggable (e.g. they're found on optional addon cards,
or in an FPGA that's dynamically reprogrammed). In these cases,
that's not the situation; it's an SOC controller and the only device
is initialized before these drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up duplicate includes in
drivers/spi/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it
only writes one zero filled word to the transmit register. If the driver
expects to receive more than one word it will wait forever for a second
receive interrupt. With this patch the controller will shift out zeroes
until all words have been received.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix cut 'n paste bug in Atmel SPI driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update various SPI drivers so they properly support
- coldplug through "modprobe $(cat /sys/devices/.../modalias)"
- hotplug through "modprobe $(MODALIAS)"
The basic rule for platform, SPI, and (new style) I2C drivers is just
to make sure that modprobing the driver name works. In this case, all
the relevant drivers are platform drivers, and this patch either
(a) Changes the driver name, if no in-tree code would break;
this is simpler and thus preferable in the long term.
(b) Adds MODULE_ALIAS directives, when in-tree platforms declare
devices using the current driver name; less desirable.
Most systems will link SPI controller drivers statically, but
there's no point in being needlessly broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer
without a cast" reported on SH ... most architectures use macros in that
test, SH uses inlined functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long ago I've noticed (but didn't pay much attention) that
spi_mpc83xx using PM calculations that differs from what
specs describe. I.e.
u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4);
While specs says: "The SPI baud rate generator clock source (either
system clock or system clock divided by 16, depending on DIV16 bit) is
divided by 4 * ([PM] + 1), a range from 4 to 64.".
Thus " - 1" is missing in the spi_mpc83xx's formula.
Why nobody noticed that bug? Probably because sysclk usually less then
user expects, e.g. you expect 200 MHz, but real clock is 198 MHz,
and integer rounding helps when this formula is used.
Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz
requested.
PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz
At lower frequencies this bug is more noticeable, though.
And this bug shows itself in all its beauty if SYSCLK is equal or a bit
more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG):
PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz!
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's
SYSCLK/2 for MPC8323E (SPI in QE). Fix this, and remove confusion by
renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates some error reporting paths in SPI device setup:
- Move validation logic for SPI chipselects to spi_new_device(),
which is where it should always have been.
- In spi_new_device(), emit error messages if the device can't
be created. This is LOTS better than a silent failure; though
eventually, the calling convention should probably change to
use the <linux/err.h> conventions.
- Includes one previously-missing check: SPI masters must always
have at least one chipselect, even for dedicated busses which
always keep it selected!
It also adds a FIXME (IDR for dynamic ID allocation) so the issue doesn't live
purely in my mailbox.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This exposes the hardware loopback mode to drivers, primarily for testing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev driver doesn't currently expose all SPI communications modes to
userspace. This passes them all through to the driver.
Two of them are potentially troublesome, in the sense that they could cause
hardware conflicts on shared busses. It might be appropriate to add some
privilege checks for for those modes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_mpc83xx should use other shifts when running in QE+LSB mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller supports LSB-first transfers; let drivers use them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation clearly states, that mode should not be changed till
SPMODE_ENABLE bit set. I've seen hangs w/o this patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the include files moved around during the s3c24xx arch moves.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SPI core/init code uses a semaphore as mutex. Use the mutex API instead
of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for SPI controller built into TXx9 MIPS SoCs.
This driver is derived from arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add OMAP24XX McSPI (Multichannel SPI) controller driver. This driver is
tested very well under OMAP GIT tree with N800 - Nokia Internet Tablet, and
some other OMAP2 boards.
Recent updates included bugfixes, cleanups, speedups, and better
conformance to the current SPI programming interface. This doesn't yet
understand the third controller instance on the OMAP 2430.
[david-b@pacbell.net: more minor cleanups to the omap2_mcspi driver]
Signed-off-by: Juha Yrjölä <juha.yrjola@solidboot.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to
the SPI controller. This patch adds a qe_mode knob that sees to that
needed adaptions are performed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple SPI master driver for Xilinx SPI controller.
No support for multiple masters.
Not using level 1 drivers from EDK.
[akpm@linux-foundation.org: uninlining]
Signed-off-by: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tweak Kconfig for the S3C24XX SPI controller drivers. Both use the bitbang
framework; only one previously said that. Plus in this case "select" is
the right way to manage that dependency, since folk will not know up front
to enable bitbang in order to even see those S3C drivers in order to enable
them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update chipselect handling for atmel_spi:
* Teach it how to leave chipselect active between messages; this
helps various drivers work better.
* Cope with at91rm0200 errata: nCS0 can't be managed with GPIOs.
The MR.PCS value is now updated whenever a chipselect changes.
(This requires SPI pinmux init for that controller to change,
and also testing on rm9200; doesn't break at91sam9 or avr32.)
* Fix minor glitches: spi_setup() must leave chipselects inactive,
as must removal of the spi_device.
Also tweak diagnostic messaging to be a bit more useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor updates to atmel_spi:
- DMA:
* Comments to explain the DMA policies
* Report any mapping errors from spi_transfer()
* Remove extra loop for DMA mapping
- Diagnostics: report minimum clock rate, if we need to reject a
spi_setup() request because that rate is too low.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPC83xx SPI controller clock divider can divide the system clock by not
more then 1024. The spi_mpc83xx driver does not check this and silently
writes garbage to the SPI controller registers when asked to run at lower
frequencies. I've tried to run the SPI on a 266MHz MPC8349E with 100kHz
for debugging a bus problem and suddenly was confronted with a 2nd problem
to debug.. ;-)
The patch adds an additional check which avoids writing garbage to the SPI
controller registers and warn the user about it. This might help others to
avoid simmilar problems.
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the LM70-LLP parport adapter, which is an eval board
for the LM70 temperature sensor. For those without that board, it may be a
simpler example of a parport-to-SPI adapter then spi_butterfly.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Doc, coding style, and interface updates; build fixes. Minor rename.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of annoying GCC warning on 32-bit platforms.
drivers/spi/spidev.c: In function 'spidev_message':
drivers/spi/spidev.c:184: warning: cast to pointer from integer of different size
drivers/spi/spidev.c:216: warning: cast to pointer from integer of different size
The trick is to add an extra cast using "ptrdiff_t" to convert the u64 to
the correct size integer, and only then casting it into a "void *" pointer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix SPI dynamic bus ID assignment to start at 2^15-1 rather than a negative
number. Valid bus ids are supposed to be positive, and are (now) stored in
an 's16' value.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 2 bugs:
- SPI_DMA_RHDMA bad value.
- Missing return value in setup() function (lost passing from
patch-2.6.20-rc4-spi_imx to patch-2.6.20-rc6-spi_imx).
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When either rx_buf or tx_buf is not being used, i.e. for plain read- or
write operations, the atmel_spi uses a fixed-size DMA buffer instead. If
the transfer is longer than the size of this buffer, it is split into
multiple DMA transfers.
When the transfer is split like this, the atmel_spi driver ends up using
the same DMA address again and again even for the buffer that came from the
user, which is of course wrong. Fix this by adding the number of bytes
already transferred to the DMA address so that the data ends up in the
right place.
Thanks to Wu Xuan for discovering this bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The omap_uwire controller driver handles SPI_CPHA incorrectly;
It should mean:
CPHA=0 ... sample at leading edge of clock
CPHA=1 ... sample at trailing edge of clock
This bug has been masked by inverse bugs in layered drivers;
and was uncovered by running some of them on non-OMAP hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ioc' should be deallocated if __copy_from_user fails (found by Coverity
- CID 1644).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Message size needs to be checked before copying, or bad things could
happen.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mpc5200 PSC SPI driver to actually work for CONFIG_PPC_MERGE
- s/mpc52xx/mpc5200/, as this was changed in device tree some time ago
- fix spi id detection
The move from 'ppc' to 'powerpc' didn't quite match the latest
kernel.org code.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) platorm_driver_probe(...) instead of platform_driver_register(&driver);
b) set bfin_spi_enable and bfin_spi_disable static
c) Why is the width flag a u32?
d) maybe use dev_dbg() instead of pr_debug()
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_first_zero_bit accepts number of bits, not longs.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI master driver for MPC52xx using its Programmable Serial Controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dragos Carp <dragos.carp@toptica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that the cpu_is_xxx() macros are available both on AVR32 and AT91, we can
remove a couple of #ifdefs from this driver. One of them is actually wrong --
new_1 should be set on AVR32 but isn't. This causes the bus clock to run at
twice the speed it is configured to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
