* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
MAINTAINERS: add myself as maintainer of USB/IP
usb: r8a66597-hcd: fix cannot detect low/full speed device
USB: ehci-ath79: fix a NULL pointer dereference
USB: Add new FT232H chip to drivers/usb/serial/ftdi_sio.c
usb/isp1760: Fix bug preventing the unlinking of control urbs
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
USB: don't let errors prevent system sleep
USB: don't let the hub driver prevent system sleep
USB: change maintainership of ohci-hcd and ehci-hcd
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
USB: TI 3410/5052 USB Serial Driver: Fix mem leak when firmware is too big.
usb: musb: gadget: clear TXPKTRDY flag when set FLUSHFIFO
usb: musb: host: compare status for negative error values
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: fix build breakages on some platforms
Staging: brcm80211: disable drivers except for X86 or MIPS platforms
Staging: brcm80211: disable drivers for PPC platforms
Staging: iio: Make IIO depend on GENERIC_HARDIRQS
Staging: mei: fix suspend failure
Staging: fix iio builds when IIO_RING_BUFFER is not enabled
Staging: Comedi: Build only on arches providing PAGE_KERNEL_NOCACHE
Staging: fix more iio builds when IIO_RING_BUFFER is not enabled
/proc/PID/io may be used for gathering private information. E.g. for
openssh and vsftpd daemons wchars/rchars may be used to learn the
precise password length. Restrict it to processes being able to ptrace
the target process.
ptrace_may_access() is needed to prevent keeping open file descriptor of
"io" file, executing setuid binary and gathering io information of the
setuid'ed process.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.
We should check if the device is faulty before considering it to be a
spare. This will avoid trying to start a recovery that cannot
proceed.
This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.
Cc: stable@kernel.org
Reported-by: Jim Paradis <james.paradis@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.
Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.
Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.
Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this section mismatch:
WARNING: drivers/misc/ioc4.o(.data+0x144): Section mismatch in reference from the variable ioc4_load_modules_work to the function .devinit.text:ioc4_load_modules()
The variable ioc4_load_modules_work references
the function __devinit ioc4_load_modules()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
This one is potentially fatal; by the time ioc4_load_modules is invoked
it may already have been freed. For that reason ioc4_load_modules_work
can't be turned to __devinitdata but also because it's referenced in
ioc4_exit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Brent Casavant <bcasavan@sgi.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this section mismatch:
WARNING: drivers/leds/leds-lp5523.o(.text+0x12f4): Section mismatch in reference from the function lp5523_probe() to the function .init.text:lp5523_init_led()
The function lp5523_probe() references
the function __init lp5523_init_led().
This is often because lp5523_probe lacks a __init
annotation or the annotation of lp5523_init_led is wrong.
Fixing this one triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this section mismatch:
WARNING: drivers/leds/leds-lp5521.o(.text+0xf2c): Section mismatch in reference from the function lp5521_probe() to the function .init.text:lp5521_init_led()
The function lp5521_probe() references
the function __init lp5521_init_led().
This is often because lp5521_probe lacks a __init
annotation or the annotation of lp5521_init_led is wrong.
Fixing this mismatch triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d149e3b25d ("memcg: add the soft_limit reclaim in global direct
reclaim") adds a softlimit hook to shrink_zones(). By this, soft limit
is called as
try_to_free_pages()
do_try_to_free_pages()
shrink_zones()
mem_cgroup_soft_limit_reclaim()
Then, direct reclaim is memcg softlimit hint aware, now.
But, the memory cgroup's "limit" path can call softlimit shrinker.
try_to_free_mem_cgroup_pages()
do_try_to_free_pages()
shrink_zones()
mem_cgroup_soft_limit_reclaim()
This will cause a global reclaim when a memcg hits limit.
This is bug. soft_limit_reclaim() should be called when
scanning_global_lru(sc) == true.
And the commit adds a variable "total_scanned" for counting softlimit
scanned pages....it's not "total". This patch removes the variable and
update sc->nr_scanned instead of it. This will affect shrink_slab()'s
scan condition but, global LRU is scanned by softlimit and I think this
change makes sense.
TODO: avoid too much scanning of a zone when softlimit did enough work.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Ying Han <yinghan@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently a single process may register exit handlers unlimited times.
It may lead to a bloated listeners chain and very slow process
terminations.
Eg after 10KK sent TASKSTATS_CMD_ATTR_REGISTER_CPUMASKs ~300 Mb of
kernel memory is stolen for the handlers chain and "time id" shows 2-7
seconds instead of normal 0.003. It makes it possible to exhaust all
kernel memory and to eat much of CPU time by triggerring numerous exits
on a single CPU.
The patch limits the number of times a single process may register
itself on a single CPU to one.
One little issue is kept unfixed - as taskstats_exit() is called before
exit_files() in do_exit(), the orphaned listener entry (if it was not
explicitly deregistered) is kept until the next someone's exit() and
implicit deregistration in send_cpu_listeners(). So, if a process
registered itself as a listener exits and the next spawned process gets
the same pid, it would inherit taskstats attributes.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under heavy memory and filesystem load, users observe the assertion
mapping->nrpages == 0 in end_writeback() trigger. This can be caused by
page reclaim reclaiming the last page from a mapping in the following
race:
CPU0 CPU1
...
shrink_page_list()
__remove_mapping()
__delete_from_page_cache()
radix_tree_delete()
evict_inode()
truncate_inode_pages()
truncate_inode_pages_range()
pagevec_lookup() - finds nothing
end_writeback()
mapping->nrpages != 0 -> BUG
page->mapping = NULL
mapping->nrpages--
Fix the problem by doing a reliable check of mapping->nrpages under
mapping->tree_lock in end_writeback().
Analyzed by Jay <jinshan.xiong@whamcloud.com>, lost in LKML, and dug out
by Miklos Szeredi <mszeredi@suse.de>.
Cc: Jay <jinshan.xiong@whamcloud.com>
Cc: Miklos Szeredi <mszeredi@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We cannot take a mutex while holding a spinlock, so flip the order and
fix the locking documentation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done. Because of this we never call lkdtm_do_action(). This patch just
adds a spinlock to protect count.
Reported-by: Tapan Dhimant <tdhimant@akamai.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: Ankita Garg <ankita@in.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is required for tilegx to be able to use the compat unistd.h header
where compat_sys_sendmmsg() is now mentioned.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
romfs_get_unmapped_area() checks argument `len' without considering
PAGE_ALIGN which will cause do_mmap_pgoff() return -EINVAL error after
commit f67d9b1576 ("nommu: add page_align to mmap").
Fix the check by changing it in same way ramfs_nommu_get_unmapped_area()
was changed in ramfs/file-nommu.c.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To make SLUB work on UML we need this_cpu_cmpxchg from
asm-generic/percpu.h.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PT7C4338 chip is being manufactured by Pericom Technology Inc. It is a
serial real-time clock which provides:
1) Low-power clock/calendar.
2) Programmable square-wave output.
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although it is used (by i915) on nothing but tmpfs, read_cache_page_gfp()
is unsuited to tmpfs, because it inserts a page into pagecache before
calling the filesystem's ->readpage: tmpfs may have pages in swapcache
which only it knows how to locate and switch to filecache.
At present tmpfs provides a ->readpage method, and copes with this by
copying pages; but soon we can simplify it by removing its ->readpage.
Provide shmem_read_mapping_page_gfp() now, ready for that transition,
Export shmem_read_mapping_page_gfp() and add it to list in shmem_fs.h,
with shmem_read_mapping_page() inline for the common mapping_gfp case.
(shmem_read_mapping_page_gfp or shmem_read_cache_page_gfp? Generally the
read_mapping_page functions use the mapping's ->readpage, and the
read_cache_page functions use the supplied filler, so I think
read_cache_page_gfp was slightly misnamed.)
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2.6.35's new truncate convention gave tmpfs the opportunity to control
its file truncation, no longer enforced from outside by vmtruncate().
We shall want to build upon that, to handle pagecache and swap together.
Slightly redefine the ->truncate_range interface: let it now be called
between the unmap_mapping_range()s, with the filesystem responsible for
doing the truncate_inode_pages_range() from it - just as the filesystem
is nowadays responsible for doing that from its ->setattr.
Let's rename shmem_notify_change() to shmem_setattr(). Instead of
calling the generic truncate_setsize(), bring that code in so we can
call shmem_truncate_range() - which will later be updated to perform its
own variant of truncate_inode_pages_range().
Remove the punch_hole unmap_mapping_range() from shmem_truncate_range():
now that the COW's unmap_mapping_range() comes after ->truncate_range,
there is no need to call it a third time.
Export shmem_truncate_range() and add it to the list in shmem_fs.h, so
that i915_gem_object_truncate() can call it explicitly in future; get
this patch in first, then update drm/i915 once this is available (until
then, i915 will just be doing the truncate_inode_pages() twice).
Though introduced five years ago, no other filesystem is implementing
->truncate_range, and its only other user is madvise(,,MADV_REMOVE): we
expect to convert it to fallocate(,FALLOC_FL_PUNCH_HOLE,,) shortly,
whereupon ->truncate_range can be removed from inode_operations -
shmem_truncate_range() will help i915 across that transition too.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before adding any more global entry points into shmem.c, gather such
prototypes into shmem_fs.h. Remove mm's own declarations from swap.h,
but for now leave the ones in mm.h: because shmem_file_setup() and
shmem_zero_setup() are called from various places, and we should not
force other subsystems to update immediately.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
You would expect to find vmtruncate_range() next to vmtruncate() in
mm/truncate.c: move it there.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 'make htmldocs' warnings:
Warning(/include/linux/hrtimer.h:153): No description found for parameter 'clockid'
Warning(/include/linux/device.h:604): Excess struct/union/enum/typedef member 'of_match' description in 'device'
Warning(/include/net/sock.h:349): Excess struct/union/enum/typedef member 'sk_rmem_alloc' description in 'sock'
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: queue: bring discard_granularity/alignment into line with SCSI
mmc: queue: append partition subname to queue thread name
mmc: core: make erase timeout calculation allow for gated clock
mmc: block: switch card to User Data Area when removing the block driver
mmc: sdio: reset card during power_restore
mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
mmc: sdhi: DMA slave ID 0 is invalid
mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
mmc: omap_hsmmc: fix ocr mask usage
mmc: sdio: fix runtime PM path during driver removal
mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
mmc: sdhi: fix module unloading
mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
mmc: vub300: fix null dereferences in error handling
Some platforms do not have virt_to_bus(), so properly depend on
CONFIG_VIRT_TO_BUS for the Comedi drivers that need this function.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As David points out, the driver is also broken on SPARC, so might
as well just only enable it on platforms where people have reported it
working, instead of trying to list all of the ones where it doesn't
work, as the working platform list is much smaller...
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Right now, bad things happen if you try to build these drivers for the
PPC platform as it seems that the code only has been tested and built on
the MIPS big endian platform.
So disable it on the PPC32 and PPC64 platforms for now, hopefully this
will be resolved in the future as I'm sure someone will want to use
these chips with that platform someday.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On m68k (which doesn't support generic hardirqs yet):
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trigger_poll’:
drivers/staging/iio/industrialio-trigger.c:180: error: implicit declaration of function ‘generic_handle_irq’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trigger_poll_chained’:
drivers/staging/iio/industrialio-trigger.c:200: error: implicit declaration of function ‘handle_nested_irq’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_release’:
drivers/staging/iio/industrialio-trigger.c:379: error: implicit declaration of function ‘irq_modify_status’
drivers/staging/iio/industrialio-trigger.c:382: error: implicit declaration of function ‘irq_set_chip’
drivers/staging/iio/industrialio-trigger.c:384: error: implicit declaration of function ‘irq_set_handler’
drivers/staging/iio/industrialio-trigger.c:388: error: implicit declaration of function ‘irq_free_descs’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_subirqmask’:
drivers/staging/iio/industrialio-trigger.c:402: error: implicit declaration of function ‘irq_data_get_irq_chip’
drivers/staging/iio/industrialio-trigger.c:402: warning: initialization makes pointer from integer without a cast
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_subirqunmask’:
drivers/staging/iio/industrialio-trigger.c:411: warning: initialization makes pointer from integer without a cast
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_allocate_trigger’:
drivers/staging/iio/industrialio-trigger.c:432: error: implicit declaration of function ‘irq_alloc_descs’
drivers/staging/iio/industrialio-trigger.c:455: error: ‘handle_simple_irq’ undeclared (first use in this function)
drivers/staging/iio/industrialio-trigger.c:455: error: (Each undeclared identifier is reported only once
drivers/staging/iio/industrialio-trigger.c:455: error: for each function it appears in.)
Hence IIO_TRIGGER should depend on GENERIC_HARDIRQS.
But as IIO_TRIGGER and IIO_RING_BUFFER form a maze of dependencies and selects,
just make the whole IIO subsystem depend on GENERIC_HARDIRQS.
This dependency also covers !S390, so that one can be removed again.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wait_event_interruptible_timeout return value was wrongly used.
The remaining timeout was used as the error code.
This fix translated wait_event_interruptible_timeout return value
into error code that can be propagated.
[10291.674121] pci_pm_suspend(): mei_pci_suspend+0x0/0x8b [mei] returns 2500
It's thinkpad t400 with
00:03.0 Communication controller [0780]: Intel Corporation Mobile 4 Series Chipset MEI Controller [8086:2a44] (rev 07)
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build by moving enum list outside of
#ifdef CONFIG_IIO_RING_BUFFER.
drivers/staging/iio/accel/adis16201_core.c:413: error: 'ADIS16201_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:417: error: 'ADIS16201_SCAN_TEMP' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:422: error: 'ADIS16201_SCAN_ACC_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:427: error: 'ADIS16201_SCAN_ACC_Y' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:432: error: 'ADIS16201_SCAN_AUX_ADC' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:436: error: 'ADIS16201_SCAN_INCLI_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:441: error: 'ADIS16201_SCAN_INCLI_Y' undeclared here (not in a function)
vers/staging/iio/accel/adis16203_core.c:374: error: 'ADIS16203_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:378: error: 'ADIS16203_SCAN_AUX_ADC' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:382: error: 'ADIS16203_SCAN_INCLI_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:388: error: 'ADIS16203_SCAN_INCLI_Y' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:392: error: 'ADIS16203_SCAN_TEMP' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On architectures that don't define PAGE_KERNEL_NOCACHE, the Comedi driver turns
into tragedy:
CC [M] drivers/staging/comedi/drivers.o
drivers/staging/comedi/drivers.c: In function ‘comedi_buf_alloc’:
drivers/staging/comedi/drivers.c:505:41: error: ‘PAGE_KERNEL_NOCACHE’ undeclared (first use in this function)
drivers/staging/comedi/drivers.c:505:41: note: each undeclared identifier is rep orted only once for each function it appears in
make[3]: *** [drivers/staging/comedi/drivers.o] Error 1
Restrict the driver to only those architectures that define PAGE_KERNEL_NOCACHE.
PAGE_KERNEL_NOCACHE is a kludge - some system architectures such as SGI IP27
are even uable to offer uncached operation - at least in the way an unwitting
driver might assume. I haven't looked in details how the driver is using
the area vmaped with PAGE_KERNEL_NOCACHE but maybe doing it XFS-style using
cached memory and the flush_kernel_vmap_range / invalidate_kernel_vmap_range
APIs in conjunction with the DMA API is a practical alternative.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix lots more build errors in staging/iio when CONFIG_IIO_RING_BUFFER
is not enabled by moving enums and defines outside of the
CONFIG_IIO_RING_BUFFER ifdef block.
Examples (one from each driver; there were 116 total errors):
drivers/staging/iio/accel/adis16204_core.c:437: error: 'ADIS16204_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16209_core.c:410: error: 'ADIS16209_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/gyro/adis16260_core.c:420: error: 'ADIS16260_SCAN_GYRO' undeclared here (not in a function)
drivers/staging/iio/imu/adis16400_core.c:565: error: 'ADIS16400_SCAN_SUPPLY' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end
of nodes. But, it's not defined in linux/mmzone.h but defined in
/arch/???/include/mmzone.h which is included only under
CONFIG_NEED_MULTIPLE_NODES=y.
Then, we see
mm/page_cgroup.c: In function 'page_cgroup_init':
mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn'
mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn'
So, fixiing page_cgroup.c is an idea...
But node_start_pfn()/node_end_pfn() is a very generic macro and
should be implemented in the same manner for all archs.
(m32r has different implementation...)
This patch removes definitions of node_start/end_pfn() in each archs
and defines a unified one in linux/mmzone.h. It's not under
CONFIG_NEED_MULTIPLE_NODES, now.
A result of macro expansion is here (mm/page_cgroup.c)
for !NUMA
start_pfn = ((&contig_page_data)->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
for NUMA (x86-64)
start_pfn = ((node_data[nid])->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
Changelog:
- fixed to avoid using "nid" twice in node_end_pfn() macro.
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can control "Transaction Translators", but
the hcd->has_tt is not set.
Since the commit d199c96d41
("USB: prevent buggy from crashing the USB stack") has checked it,
the driver could not work the low/full speed device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Loading the ehci-hcd module on the ath79 platform causes
a NULL pointer dereference:
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == c0252928, ra == c00de968
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000070 00000001 00000000
$ 4 : 802cf870 0000117e ffffffff 8019c7bc
$ 8 : 0000000a 00000002 00000001 fffffffb
$12 : 8026ef20 0000000f ffffff80 802dad3c
$16 : 8077a2d4 8077a200 c00f3484 8019ed84
$20 : c00f0000 00000003 000000a0 80262c2c
$24 : 00000002 80079da0
$28 : 80788000 80789c80 80262b14 c00de968
Hi : 00000000
Lo : b61f0000
epc : c0252928 __mod_vermagic5+0xc260/0xc7e8 [ehci_hcd]
Not tainted
ra : c00de968 usb_add_hcd+0x2a4/0x858 [usbcore]
Status: 1000c003 KERNEL EXL IE
Cause : 00800008
BadVA : 00000000
PrId : 00019374 (MIPS 24Kc)
Modules linked in: ehci_hcd(+) pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG
xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filte
r ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc ath mac80211
usbcore nls_base input_polldev crc_ccitt cfg80211 compat input_core a
rc4 aes_generic crypto_algapi
Process insmod (pid: 379, threadinfo=80788000, task=80ca2180,
tls=77fe52d0)
Stack : c0253184 80c57d80 80789cac 8077a200 00000001 8019edc0 807fa800 8077a200
8077a290 c00f3484 8019ed84 c00f0000 00000003 000000a0 80262c2c c00de968
802d0000 800878cc c0253228 c02528e4 c0253184 80c57d80 80bf6800 80ca2180
8007b75c 00000000 8077a200 802cf830 802d0000 00000003 fffffff4 00000015
00000348 00000124 800b189c c024bb4c c0255000 801a27e8 c0253228 c02528e4
...
Call Trace:
[<c0252928>] __mod_vermagic5+0xc260/0xc7e8 [ehci_hcd]
It is caused by:
commit c430131a02
Author: Jan Andersson <jan@gaisler.com>
Date: Tue May 3 20:11:57 2011 +0200
USB: EHCI: Support controllers with big endian capability regs
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reading of the HC capability register has been moved by that
commit to a place where the ehci->caps field is not initialized
yet. This patch moves the reading of the register back to the
original place.
Acked-by: Jan Andersson <jan@gaisler.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appended patch adds support for the new FTDI FT232H chip. This chip is a
single channel version of the dual FT2232H/quad FT4232H, coming with it's
own default PID 0x6014 (FT2232H uses the same PID 0x6010 like FT2232C,
FT4232H has also it's own PID).
The patch was checked on an UM232H module and a terminal program with TX/RX
shorted to that typing in the terminal reproduced the characters.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both control and bulk transfers use isp1760 slots of type ATL, but the
driver unlink code for ATL slots only acts on urbs describing a bulk
transfer, letting the code for INT slots take care of the unlink instead,
which often ended up removing the interrupt transfer for root hub events
instead. That's not good, and gets fixed by this patch.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
USB: Fix up URB error codes to reflect implementation.
xhci: Always set urb->status to zero for isoc endpoints.
xhci: Add reset on resume quirk for asrock p67 host
xHCI 1.0: Incompatible Device Error
xHCI 1.0: Force Stopped Event(FSE)
xhci: Don't warn about zeroed bMaxBurst descriptor field.
USB: Free bandwidth when usb_disable_device is called.
xhci: Reject double add of active endpoints.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
btrfs: fix inconsonant inode information
Btrfs: make sure to update total_bitmaps when freeing cache V3
Btrfs: fix type mismatch in find_free_extent()
Btrfs: make sure to record the transid in new inodes
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: prevent bogus assert when trying to remove non-existent attribute
xfs: clear XFS_IDIRTY_RELEASE on truncate down
xfs: reset inode per-lifetime state when recycling it
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for a new Lumio dual-touch panel
HID: hid-multitouch: correct VID for Stantum panels
HID: hid-multitouch: ensure slots are initialized
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] allow setting of upper 32 bit in smp_ctl_set_bit
[S390] hwsampler: Set a sane default sampling rate
[S390] s390: enforce HW limits for the initial sampling rate
[S390] kvm-s390: fix kconfig dependencies
Linus Torvalds