If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio.c
em28xx-dvb.c
- Em28xx extensions should ensure they are being only loaded against devices
that support them. Deals with case where there are multiple em28xx
devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-video.c
- Properly handle loading of the module when multiple devices are already
connected (such as at bootup). Before we were only calling dvb_init()
against the last device in the list, so while we were handling subsequent
adds properly, if there were multiple devices present on driver load,
everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.
Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ingo Molnar wrote:
> -tip auto-testing started triggering this spinlock corruption message
> yesterday:
>
> [ 3.976213] calling acpi_rtc_init+0x0/0xd3
> [ 3.980213] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread F7C50000 could not acquire Mutex [3] [20080321]
> [ 3.992213] BUG: spinlock bad magic on CPU#0, swapper/1
> [ 3.992213] lock: c2508dc4, .magic: 00000000, .owner: swapper/1, .owner_cpu: 0
This is apparently because some parts of ACPI, including mutexes, are not
initialized when acpi=off is passed to the kernel.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes pxafb's init/exit annotations. It uses __devinit/exit for
probe functions and __init for init functions. g_options is left as
__devinitdata since it is used by both.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The esp driver currently does hand rolled reference counting of its
target. It's much easier to do what it needs to do if it's plugged into
the mid-layer callbacks (target_alloc and target_destroy) which were
designed for this case, so do it this way and get rid of the internal
target reference count.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the band selection management when scanning, so
bands are now scanned according to HW band support.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb_cache_mutex was not correctly released
under all circumstances. Both rt73usb as rt2500usb
didn't release the mutex under certain conditions
when the register access failed. Obviously such
failure would lead to deadlocks.
In addition under similar circumstances when the
bbp register couldn't be read the value must be
set to 0xff to indicate that the value is wrong.
This too didn't happen under all circumstances.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible MMIO access while the device is still down
from a suspend cycle. MMIO accesses with the device powered down
may cause crashes on certain devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
This will fix the resume hang.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OOPS reported by Friedrich Oslage <bluebird@porno-bullen.de>
The problem here is that tp->starget is set every time a lun
is allocated for a particular target so we can catch the
sdev_target parent value.
The reset handler uses the NULL'ness of this value to determine
which targets are active.
But esp_slave_destroy() does not NULL out this value when appropriate.
So for every target that doesn't respond, the SCSI bus scan causes
a stale pointer to be left here, with ensuing crashes like you're
seeing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function. With this patch, vblank interrupts will work as expected
on resume, along with other chip functions. Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Timeouts are measured in jiffies, not in seconds.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After Linus fixed the inline assembly, the CFLAGS option is not
needed anymore.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: don't drop NX bit
xen: mask unwanted pte bits in __supported_pte_mask
xen: Use wmb instead of rmb in xen_evtchn_do_upcall().
x86: fix NULL pointer deref in __switch_to
I noted that the 'struct tty_struct *real_tty' is not used in this
function, so I removed the code about 'real_tty'.
Signed-off-by: Gustavo Fernando Padovan <gustavo@las.ic.unicamp.br>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current memfree FW has a bug which in some cases, assumes that ICM
pages passed to it are cleared. This patch uses __GFP_ZERO to
allocate all ICM pages passed to the FW. Once firmware with a fix is
released, we can make the workaround conditional on firmware version.
This fixes the bug reported by Arthur Kepner <akepner@sgi.com> here:
http://lists.openfabrics.org/pipermail/general/2008-May/050026.html
Cc: <stable@kernel.org>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Rewritten to be a one-liner using __GFP_ZERO instead of vmap()ing
ICM memory and memset()ing it to 0. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mark rtc sa1100 driver as wakeup source before registering it.
rtc_device_register evaluates device_can_wakeup(rtc->dev.parent) and
supresses the creation of /sys/class/rtc/rtcX/wakealarm if
device_can_wakeup is not (yet) true.
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This issue was found by Krzysztof Helt and Eric Miao.
pxafb had issues in the order with which it cleaned up if errors occurred
during a probe. This patch reorders the failure handling sequence and also
frees the cmap and clk.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This bug was found and fixed by Lothar Wassmann.
Previously, the use of ifndef CONFIG_MODULES made it such that pxafb command
line option parsing was dependent on whether the kernel was built with module
support. The ifndef should be MODULE so that parsing is dependent only on
whether the driver is built-in or not.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: Don't receive new packets in a dead network namespace.
sctp: Make sure N * sizeof(union sctp_addr) does not overflow.
pppoe: warning fix
ipv6: Drop packets for loopback address from outside of the box.
ipv6: Remove options header when setsockopt's optlen is 0
mac80211: detect driver tx bugs
Fix warning:
drivers/net/pppoe.c: In function 'pppoe_recvmsg':
drivers/net/pppoe.c:945: warning: comparison of distinct pointer types lacks a cast
because skb->len is unsigned int and total_len is size_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
BAST: Remove old IDE driver
pcmcia ide kingston compactflash's have a new manufacturer id
pcmcia: add another pata/ide ID
pcmcia: add an pata/ide ID
ide: increase timeout in wait_drive_not_busy()
palm_bk3710: fix resource management
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: Kconfig menu touch-up
firewire: Kconfig menu touch-up
firewire: deadline for PHY config transmission
firewire: fw-ohci: unify printk prefixes
firewire: fill_bus_reset_event needs lock protection
firewire: fw-ohci: write selfIDBufferPtr before LinkControl.rcvSelfID
firewire: fw-ohci: disable PHY packet reception into AR context
firewire: fw-ohci: use of uninitialized data in AR handler
firewire: don't panic on invalid AR request buffer
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: no AC status notification
ACPI Exception (video-1721): UNKNOWN_STATUS_CODE, Cant attach device
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
drm: only trust core drm ioctls - driver ioctls are a mess.
drm/i915: add support for Intel series 4 chipsets.
drm/radeon: add hier-z registers for r300 and r500 chipsets
drm/radeon: use DSTCACHE_CTLSTAT rather than RB2D_DSTCACHE_CTLSTAT
drm/radeon: switch IGP gart to use radeon_write_agp_base()
drm/radeon: Restore sw interrupt on resume
drm/r500: add support for AGP based cards.
drm/radeon: fix texture uploads with large 3d textures (bug 13980)
drm/radeon: add initial r500 support.
drm/radeon: init pipe setup in kernel code.
drm/radeon: fixup radeon_do_engine_reset
drm/radeon: fix pixcache and purge/cache flushing registers
drm/radeon: write AGP_BASE_2 on chips that support it.
drm/radeon: merge IGP chip setup and fixup RS400 vs RS480 support
drm/radeon: IGP clean up register and magic numbers.
drm/rs690: set base 2 to 0.
drm/rs690: set all of gart base address.
radeon: add production microcode from AMD
drm: pcigart use proper pci map interfaces.
drm: the sg alloc ioctl should write back the handle to userspace
...
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
[agp]: fixup chipset flush for new Intel G4x.
agp: brown paper bag patch - put back the two lines it took out.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin Serial Driver: Use timer to poll CTS PIN instead of workqueue.
Blackfin arch: fix typo error in bf548 serial header file
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: sis can't do PMP
ata_piix: add TECRA M4 to broken suspend list
LIBATA: Add HAVE_PATA_PLATFORM to select PATA_PLATFORM driver
sata_mv: warn on PIO with multiple DRQs
sata_mv: enable async_notify for 60x1 Rev.C0 and higher
libata: don't check whether to use DMA or not for no data commands
ahci: jmb361 has only one port
The inline assembly in drivers/watchdog/hpwdt.c was incredibly broken,
and included all the function prologue and epilogue stuff, even though
it was itself then inside a C function where the compiler would add its
own prologue and epilogue on top of it all.
This then just _happened_ to work if you had exactly the right compiler
version and exactly the right compiler flags, so that gcc just happened
to not create any prologue at all (the gcc-generated epilogue wouldn't
matter, since it would never be reached).
But the more proper way to fix it is to simply not do this. Move the
inline asm to the top level, with no surrounding function at all (the
better alternative would be to remove the prologue and make it actually
use proper description of the arguments to the inline asm, but that's a
bigger change than the one I'm willing to make right now).
Tested-by: S.Çağlar Onur <caglar@pardus.org.tr>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the old BAST IDE driver, as we are now using the platform-pata
support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Up to now, Kingston compactflash cards (ab)used the Toshiba Manufacturer's ID,
In their new CF cards, they use a new one. Let's the ide subsystem
recognize CF cards with the new id.
Signed-off-by: Christophe Niclaes <cniclaes@develtech.com>
Acked-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Addition of Transcend 1GB 45x id so that it is properly detected.
[bart: fix typo in ide-cs's ID spotted by Alan Cox]
Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some ATAPI devices take longer than the current max timeout value to
become ready (i.e. TEAC DV-W28ECW takes 6 ms) so increase the timeout
value to 10 ms.
This fixes kernel.org bugzilla bug #10887:
http://bugzilla.kernel.org/show_bug.cgi?id=10887
Reported-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver expected a *virtual* address in the IDE platform device's memory
resource and didn't request the memory region for the register block. Fix this
taking into account the fact that DaVinci SoC devices are fixed-mapped to the
virtual memory early and we can get their virtual addresses using IO_ADDRESS()
macro, not having to call ioremap()...
While at it, also do some cosmetic changes...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch is ported one from 534:77db69c38249 of linux-2.6.18-xen.hg.
Use wmb instead of rmb to enforce ordering between
evtchn_upcall_pending and evtchn_pending_sel stores
in xen_evtchn_do_upcall().
Cc: Samuel Thibault <samuel.thibault@eu.citrix.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: the arch/x86 maintainers <x86@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I am able to reproduce the oops reported by Simon in __switch_to() with
lguest.
My debug showed that there is at least one lguest specific
issue (which should be present in 2.6.25 and before aswell) and it got
exposed with a kernel oops with the recent fpu dynamic allocation patches.
In addition to the previous possible scenario (with fpu_counter), in the
presence of lguest, it is possible that the cpu's TS bit it still set and the
lguest launcher task's thread_info has TS_USEDFPU still set.
This is because of the way the lguest launcher handling the guest's TS bit.
(look at lguest_set_ts() in lguest_arch_run_guest()). This can result
in a DNA fault while doing unlazy_fpu() in __switch_to(). This will
end up causing a DNA fault in the context of new process thats
getting context switched in (as opossed to handling DNA fault in the context
of lguest launcher/helper process).
This is wrong in both pre and post 2.6.25 kernels. In the recent
2.6.26-rc series, this is showing up as NULL pointer dereferences or
sleeping function called from atomic context(__switch_to()), as
we free and dynamically allocate the FPU context for the newly
created threads. Older kernels might show some FPU corruption for processes
running inside of lguest.
With the appended patch, my test system is running for more than 50 mins
now. So atleast some of your oops (hopefully all!) should get fixed.
Please give it a try. I will spend more time with this fix tomorrow.
Reported-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LM75 sensor reading bugfix: never save error status as valid
sensor output. This could be improved, but at least this
prevents certain rude failure modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It has been reported that the abituguru3 driver fails to load after a BIOS
update. This patch fixes this by loosening the detection routine so that it
will work after the BIOS update too. To compensate for the now very loose
detection an additional check is added on the DMI Base Board vendor string to
make sure we only load on Abit motherboards, this is the same as the check in
the abituguru (1 / 2) driver.
Signed-of-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch identifies the Abit AW8D board as such, and adds support for its
aux5 fan connector
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
data->max_duty_at_overheat is not updated in adt7473_update_device,
so it might be used before it is initialized (if the user reads from
sysfs file max_duty_at_crit before writing to it.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Function RANGE_TO_REG() is broken. For a requested range of 2000 (2
degrees C), it will return an index value of 15, i.e. 80.0 degrees C,
instead of the expected index value of 0. All other values are handled
properly, just 2000 isn't.
The bug was introduced back in November 2004 by this patch:
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commit;h=1c28d80f1992240373099d863e4996cdd5d646d0
While this can be fixed easily with the current code, I'd rather
rewrite the whole function in a way which is more obviously correct.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Justin Thiessen <jthiessen@penguincomputing.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This allows other threads to run when the serial driver polls the CTS
PIN in a loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Commit 62c96b9d09 ("agp/intel: cleanup
some serious whitespace badness") didn't just fix whitespace. It also
lost two lines.
Noticed by Linus. No more whitespace diffs for me.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/intel: cleanup some serious whitespace badness
[AGP] intel_agp: Add support for Intel 4 series chipsets
[AGP] intel_agp: extra stolen mem size available for IGD_GM chipset
agp: more boolean conversions.
drivers/char/agp - use bool
agp: two-stage page destruction issue
agp/via: fixup pci ids
This adds missing stolen memory size detect for IGD_GM, be sure to
detect right size as current X intel driver (2.3.2) which has already
worked out.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to the hw guys, you should use DSTCACHE_CTLSTAT to flush
the 2D dst cache rather than RB2D_DSTCACHE_CTLSTAT.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Texture uploads could hit the blitter coordinate limit, adjust the texture
offset when uploading the pieces. Make sure to check the end address of the
upload too.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This contains all the command buffer processing for the r500 cards.
It doesn't yet contain vblank support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Piter PUNK <piterpunk@slackware.com>
SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used. Turn off PMP support.
tj: added patch description, adapted patch to #upstream-fixes and
renamed board_ahci_sis to board_ahci_nopmp.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request). In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.
A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.
So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.
So allow AN for "C0" and higher.
This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to check whether to use DMA or not for no data
commands. Don't do it. While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JMB361 has only one port but reports it has two causing longish probe
failure on the second one. Quirk it.
Reported by Gajo Petrovic in bz 10911.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
besides it apparently being useful only in 2.6.24 (the changes in 2.6.25
really mean that it could be converted back to a single-stage mechanism),
I'm seeing an issue in Xen Dom0 kernels, which is caused by the calling
of gart_to_virt() in the second stage invocations of the destroy function.
I think that besides this being a real issue with Xen (where
unmap_page_from_agp() is not just a page table attribute change), this
also is invalid from a theoretical perspective: One should not assume that
gart_to_virt() is still valid after unmapping a page. So minimally (keeping
the 2-stage mechanism) a patch like the one below would be needed.
Jan
Signed-off-by: Dave Airlie <airlied@redhat.com>
add a new PCI ID and remove an old dodgy one, include the explaination
in the commented code so nobody readds later.
(davej also sent the pci id addition).
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Fix check of is_closed flag check in ib_uverbs_async_handler()
RDMA/nes: Fix off-by-one in nes_reg_user_mr() error path
Commit 1ae5c187 ("IB/uverbs: Don't store struct file * for event
files") changed the way that closed files are handled in the uverbs
code. However, after the conversion, is_closed flag is checked
incorrectly in ib_uverbs_async_handler(). As a result, no async
events are ever passed to applications.
Found by: Ronni Zimmerman <ronniz@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rename and reorder some prompts and modify some help texts.
The result:
-------------------- IEEE 1394 (FireWire) support --------------------
*** Enable only one of the two stacks, unless you know what you are doing ***
New FireWire stack, EXPERIMENTAL
OHCI-1394 controllers
Storage devices (SBP-2 protocol)
Stable FireWire stack
OHCI-1394 controllers
PCILynx controller
Storage devices (SBP-2 protocol)
Enable replacement for physical DMA in SBP2
IP over 1394
raw1394 userspace interface
video1394 userspace interface
dv1394 userspace interface (deprecated)
Excessive debugging output
The old prompts for reference:
-------------------- IEEE 1394 (FireWire) support --------------------
IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL
Support for OHCI FireWire host controllers
Support for storage devices (SBP-2 protocol driver)
IEEE 1394 (FireWire) support
*** Subsystem Options ***
Excessive debugging output
*** Controllers ***
Texas Instruments PCILynx support
OHCI-1394 support
*** Protocols ***
OHCI-1394 Video support
SBP-2 support (Harddisks etc.)
Enable replacement for physical DMA in SBP2
IP over 1394
OHCI-DV I/O support (deprecated)
Raw IEEE1394 I/O support
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Emphasize the recommendation to build only one stack.
Trim the prompts to better fit into short attention spans.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If the low-level driver failed to initialize a card properly without
noticing it, fw-core was blocked indefinitely when trying to send a
PHY config packet. This hung up the events kernel thread, e.g. locked
up keyboard input.
https://bugzilla.redhat.com/show_bug.cgi?id=444694https://bugzilla.redhat.com/show_bug.cgi?id=446763
This problem was introduced between 2.6.25 and 2.6.26-rc1 by commit
2a0a259049 "firewire: wait until PHY
configuration packet was transmitted (fix bus reset loop)".
The solution is to wait with timeout. I tested it with 7 different
working controllers and 1 non-working controller. On the working ones,
the packet callback complete()s usually --- but not always --- before a
timeout of 10ms. Hence I chose a safer timeout of 100ms.
On the few tests with the non-working controller ALi M5271, PHY config
packet transmission always timed out so far. (Fw-ohci needs to be fixed
for this controller independently of this deadline fix. Often the core
doesn't even attempt to send a phy config because not even self ID
reception works.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The messages which can be enabled by fw-ohci's debug module parameter
are changed from KERN_DEBUG to KERN_NOTICE level and uniformly prefixed
with "firewire_ohci: ". This further simplifies communication with
users when we ask them to capture debug messages.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Callers of fill_bus_reset_event() have to take card->lock. Otherwise
access to node data may oops if node removal is in progress.
A lockless alternative would be
- event->local_node_id = card->local_node->node_id;
+ tmp = fw_node_get(card->local_node);
+ event->local_node_id = tmp->node_id;
+ fw_node_put(tmp);
and ditto with the other node pointers which fill_bus_reset_event()
accesses. But I went the locked route because one of the two callers
already holds the lock. As a bonus, we don't need the memory barrier
anymore because device->generation and device->node_id are written in
a card->lock protected section.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
OHCI 1.1 clause 5.10 requires that selfIDBufferPtr is valid when a 1 is
written into LinkControl.rcvSelfID.
This driver bug has so far not been known to cause harm because most
chips obviously accept a later selfIDBufferPtr write, at least before
HCControl.linkEnable is written.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
We want the rcvPhyPkt bit in LinkControl off before we start using the
chip. However, the spec says that the reset value of it is undefined.
Hence switch it explicitly off.
https://bugzilla.redhat.com/show_bug.cgi?id=244576#c48 shows that for
example the nForce2 integrated FireWire controller seems to have it on
by default.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
header_length and payload_length are filled with random data if an
unknown tcode was read from the AR buffer (i.e. if the AR buffer
contained invalid data).
We still need a better strategy to recover from this, but at least
handle_ar_packet now doesn't return out of bound buffer addresses
anymore.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
BUG() at this place is wrong. (Unless if the low level driver would
already do higher-level input validation of incoming request headers.)
Invalid incoming requests or bugs in the controller which corrupt the
AR-req buffer needlessly crashed the box because this is run in tasklet
context.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] dpt_i2o: Add PROC_IA64 define
[SCSI] scsi_host regression: fix scsi host leak
[SCSI] sr: fix corrupt CD data after media change and delay
By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: Ang Way Chuang <wcang@nav6.org>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To get this driver working we need the CFLAGS_hpwdt.o += -O in the Makefile.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver needs the asmlinkage tag and the CFLAGS line in the Makefile.
Without it the driver doesn't work.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some boxes the touchpad needs to be reinitialized after resume to make
it function again. This fixes bugzilla #10825.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are systems that fail in i8042_resume() with
i8042: Can't write CTR to resume
as i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR) fails even though the
controller claimed itself to be ready before.
One retry after failing write fixes the problems on the failing systems.
Reported-by: Helmut Schaa <hschaa@novell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following build error with CONFIG_BLK_DEV_IDE_PMAC=n:
<-- snip -->
...
CC drivers/macintosh/mediabay.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/macintosh/mediabay.c: In function 'check_media_bay':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/macintosh/mediabay.c:428: error: 'struct media_bay_info' has no member named 'cd_index'
make[3]: *** [drivers/macintosh/mediabay.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_name, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
statement S;
identifier f;
expression E;
constant C;
@@
n = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f(n,...)
when != E = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n1 = f(n,...)
|
E = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-generic: don't probe all legacy ISA IDE ports by default
ide-cs: fix releasing I/O resources
ide-cs: fix probing and add warm-plug support
ide-pmac: remove bogus comment about pmac_ide_setup_device()
ide-pmac: add ->cable_detect method
ide-pmac: bugfix for media-bay support rework
opti621: add PIO 4 support
opti621: use pre-calculated PIO timings
opti621: program devices timings separately in ->set_pio_mode
opti621: use PCI clock value provided by controller
opti621: remove DMA support
opti621: disable read prefetch
lguest (in rusty's use-tun-ringfd patch) assumes that the
guest has updated its feature bits before setting its status
to VIRTIO_CONFIG_S_DRIVER_OK.
That's pretty reasonable, so let's make it so.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can't probe all legacy ISA IDE ports by default as the resources may be
occupied by other ISA devices. Add "probe_mask" module parameter and probe
only first two ISA IDE ports by default leaving the decision about probing
the rest to the user (systems with ISA ide2-6 should be very, very rare).
This fixes a regression caused by:
commit 343a3451e2
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Tue Jun 10 20:56:36 2008 +0200
ide-generic: add missing hwif->chipset setup
...
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Bisected-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif content is already freed after ide_release() call so cache
hwif->io_ports.{data,ctl}_addr in local variables in ide_detach().
This fixes post-2.6.25 regression.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix probing by using ide_port_scan() and moving "retry loop"
from ide_config() to idecs_register().
* Don't fail probe if there are no devices attached to a port.
* Remove (now redundant) error message from ide_config().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->cable_detect method and remove no longer needed pmif->cable_80 flag
(there is also no need to mask ->udma_mask now).
This fixes:
- forced ignoring of cable detection (needed for some CF devices & debug)
- cable detection for warm-plug
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add PIO 4 support.
While at it:
* Use a single struct ide_port_info instance for OPTi621 and OPTi621X.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use pre-calculated PIO timings in ->set_pio_mode.
* Remove no longer needed compute_clocks(), cmpt_clk(), struct pio_clocks_s,
PIO_* defines and OPTI621_DEBUG define.
There should be no functional changes caused by this patch.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set drive->drive_data to 'pio + XFER_PIO_0' instead of 'pio',
then simplify selecting maximum adress setup timing.
* Remove no longer needed compute_pios() and opti621_port_init_devs().
* Program devices timings separately in ->set_pio_mode.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use PCI clock value provided by controller instead of depending on
a default (or user supplied) value.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These controllers don't support DMA.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This fixes the following compile failure:
drivers/scsi/dpt_i2o.c:83: error: 'PROC_IA64' undeclared here (not in a function)
Mark Salyzyn <Mark_Salyzyn@adaptec.com> indicated that IA64 must report
itself as PROC_INTEL, so I've changed the comment for PROC_INTEL.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
commit 9c7701088a
Author: Dave Young <hidave.darkstar@gmail.com>
Date: Tue Jan 22 14:01:34 2008 +0800
scsi: use class iteration api
Isn't a correct replacement for the original hand rolled host
lookup. The problem is that class_find_child would get a reference to
the host's class device which is never released. Since the host class
device holds a reference to the host gendev, the host can never be
freed.
In 2.6.26 we started using class_find_device, and this function also
gets a reference to the device, so we end up with an extra ref
and the host will not get released.
This patch adds a put_device to balance the class_find_device() get. I
kept the scsi_host_get in scsi_host_lookup, because the target layer
is using scsi_host_lookup and it looks like it needs the SHOST_DEL
check.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fixup write combine comment in pci_mmap_resource
x86: PAT export resource_wc in pci sysfs
x86, pci-dma.c: don't always add __GFP_NORETRY to gfp
suspend-vs-iommu: prevent suspend if we could not resume
x86: pci-dma.c: use __GFP_NO_OOM instead of __GFP_NORETRY
pci, x86: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
PCI: use dev_to_node in pci_call_probe
PCI: Correct last two HP entries in the bfsort whitelist
The child of a video bus device is not alway a video device.
It should be a warn message rather than an exception here.
http://bugzilla.kernel.org/show_bug.cgi?id=9761
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes setting the coherent DMA mask for PCI devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Workaround HW bug for SB600/700 SATA controller PMP support
ahci: workarounds for mcp65
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Revert 'process defer accept as established' changes.
ipv6: Fix duplicate initialization of rawv6_prot.destroy
bnx2x: Updating the Maintainer
net: Eliminate flush_scheduled_work() calls while RTNL is held.
drivers/net/r6040.c: correct bad use of round_jiffies()
fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
netfilter: Make nflog quiet when no one listen in userspace.
ipv6: Fail with appropriate error code when setting not-applicable sockopt.
ipv6: Check IPV6_MULTICAST_LOOP option value.
ipv6: Check the hop limit setting in ancillary data.
ipv6 route: Fix route lifetime in netlink message.
ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
dccp: Bug in initial acknowledgment number assignment
dccp ccid-3: X truncated due to type conversion
dccp ccid-3: TFRC reverse-lookup Bug-Fix
dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
dccp: Fix sparse warnings
dccp ccid-3: Bug-Fix - Zero RTT is possible
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This enforces us to use the drm ioctl types so read/write works correctly and not believe
what userspace tells us.
It does this hopefully without breaking the drm api.
Fixes bug from thread: BUG: unable to handle kernel NULL pointer dereference (drm_getunique)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More Kconfig tweaks related to the legacy PC RTC code:
- Describe the legacy PC RTC driver as such ... it's never quite
been clear that this driver is for PC RTCs, and now it's fair
to call this the "legacy" driver.
- Force it to understand about HPET stealing its IRQs ... kernel
code does this always when HPET is in use, there should be no
option for users to goof up the config.
This seems to fix kernel bugzilla #10729.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several console keyboard maps are broken since
commit 04c7197650
Author: Samuel Thibault <samuel.thibault@ens-lyon.org>
Date: Tue Oct 16 23:27:04 2007 -0700
unicode diacritics support
because that changeset made k_self consider the value as a latin1
character when in Unicode mode, which is wrong; k_self should still take
the console map into account.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic nvram driver announces itself as
'Macintosh non-volatile memory driver'
instead of 'Generic non-volatile memory driver'. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the cirrusfb driver, the RAM address printk has a superfluous 'x' that
could be interpreted as "don't care", while it is actually a typo. Fix
that.
[akpm@linux-foundation.org: join the two printk strings to make it atomic]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many distros load this driver by default (throw it against the wall
and see what sticks method). Change the error message severity level to
avoid alarming users. Isn't it annoying when users actually read the
error logs...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spid has been allocated in this function and so should be freed before
leaving it, as in the other error handling cases.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@r exists@
expression E,E1;
statement S;
position p1,p2,p3;
@@
E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != E = E1
if (E == NULL || ...) S
... when != E = E1
if@p2 (...) {
... when != kfree(E)
}
... when != E = E1
kfree@p3(E);
@forall@
position r.p2;
expression r.E;
int E1 != 0;
@@
* if@p2 (...) {
... when != kfree(E)
when strict
return E1; }
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we
allocate one. Tasklets may be scheduled in the interrupt handler but they
will be initialized after the handler returns, causing a BUG() in
kernel/softirq.c when they run.
Should fix this Fedora bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=449817
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alarm->pending indicates whether there's an alarm that has actually been
triggered, not whether we're waiting for it. alarm->enabled indicates
that.
Also add missing locking around reading the RTC registers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the next generation of HP Smart Array SAS/SATA
controllers. Shipping date is late Fall 2008.
Bump the driver version to 3.6.20 to reflect the new hardware support from
patch 1 of this set.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Krufky