The current DWARF info for CR are incorrect, causing the gcc unwinder to
go to lunch if we take a segfault in the vdso. This fixes it.
Problem identified by Andrew Haley, and fix provided by Jakub Jelinek
(thanks !).
Unfortunately, a bug in gcc cause it to not quite work either, but that
is being fixed separately with something around the lines of:
linux-unwind.h:
fs->regs.reg[R_CR2].loc.offset = (long) ®s->ccr - new_cfa;
+ /* CR? regs are just 32-bit and PPC is big-endian. */
+ fs->regs.reg[R_CR2].loc.offset += sizeof (long) - 4;
(According to Jakub)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PA6T has a bug where the slbie instruction does not honor the large
segment bit. As a result, we have to always use slbia when switching
context.
We don't have to worry about changing the slbie's during fault processing,
since they should never be replacing one VSID with another using the
same ESID. I.e. there's no risk for inserting duplicate entries due to a
failed slbie of the old entry. So as long as we clear it out on context
switch we should be fine.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable NO_HZ and high res timers for the ppc64 and pseries defconfigs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After 6 years the ppc64 kernel still thinks its important to tell me my
cache line size is 0x80 bytes. I think most people who care know that by
now. The rest probably cant even understand the hex output.
Since we might have misconfigured firmware or cpus that have a linesize
that isnt 128 bytes, I still print it out for those cases. If people
would prefer to remove it completely, lets do it.
Also for lpar remove the htab_address printout since its not used.
Anton
ppc64 boot log usability expert
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The clockevent bootup message only needs to be KERN_INFO.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When checking out the new NO_HZ support in powerpc, I noticed we never
slept for more than 2 seconds. It turns out SLAB has a 2 second per cpu
timer that causes this.
After switching to SLUB I see some nice 4 second sleeps which is the
limit on this POWER6 box (the decrementer ticks at 512MHz):
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 3.96 sec
slept 3.80 sec
slept 2.99 sec
Since SLUB is now the default and some powerpc defconfigs already enable
it, lets enable SLUB across the board for consistency. While doing this
I also noticed that the maple defconfig has SLAB debugging enabled which
is sure to make your box nice and slow. Fix that too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Buglet in the 1TB detection makes it return after checking the first
property word, even if it's not a match.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 1189be6508 ([POWERPC] Use 1TB
segments) added an argument to hpte_insert.
Also make iSeries_hpte_insert static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace struct ibmebus_dev and struct ibmebus_driver with struct of_device
and struct of_platform_driver, respectively. Match the external ibmebus
interface and drivers using it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The devtree root is now searched for devices matching a built-in whitelist
during boot, so these devices appear on the bus from the beginning. It is
still possible to manually add/remove devices to/from the bus by using the
probe/remove sysfs interface. Also, when a device driver registers itself,
the devtree is matched against its matchlist.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove old code that will be replaced by rewritten and shorter functions in
the next patch. Keep struct ibmebus_dev and struct ibmebus_driver for now,
but replace ibmebus_{,un}register_driver() by dummy functions. This way, the
kernel will still compile and run during the transition and git bisect will
be happy.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Extract generic of_device allocation code from of_platform_device_create()
and move it into of_device.[ch], called of_device_alloc(). Also, there's now
of_device_free() which puts the device node.
This way, bus drivers that build on of_platform (like ibmebus will) can
build upon this code instead of reinventing the wheel.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
WOL bugfix for 3c59x.c
skge 1.12
skge: add a debug interface
skge: eeprom support
skge: internal stats
skge: XM PHY handling fixes
skge: changing MTU while running causes problems
skge: fix ram buffer size calculation
gianfar: Fix compile regression caused by 09f75cd7
net: Fix new EMAC driver for NAPI changes
bonding: two small fixes for IPoIB support
e1000e: don't poke PHY registers to retreive link status
e1000e: fix error checks
e1000e: Fix debug printk macro
tokenring/3c359.c: fixed array index problem
[netdrvr] forcedeth: remove in-driver copy of net_device_stats
[netdrvr] forcedeth: improved probe info; dev_printk() cleanups
forcedeth: fix NAPI rx poll function
AFAICS, fallout from repacing include of blkdev.h with include of bio.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a lost 'key' variable declaration that went missing in a
mismerge (commit b981d8b3f5)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some NICs (3c905B) can not generate PME in power state PCI_D0, while others
like 3c905C can. Call pci_enable_wake() with PCI_D3hot should give proper
WOL for 3c905B.
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Tested-by: Harry Coin <hcoin@n4comm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a debugfs interface to look at internal ring state.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change how PHY is managed on SysKonnect fibre based boards.
Poll for PHY coming up 1 per second, but use interrupt to detect loss.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than bring network down/up when changing MTU,
only need to impact receiver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes problems with transmit hangs on older fiber based SysKonnect boards.
Adjust ram buffer sizing calculation to make it correct on all boards
and make it like the code in sky2 driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net: Fix new EMAC driver for NAPI changes
This fixes the new EMAC driver for the NAPI updates. The previous patch
by Roland Dreier (already applied) to do that doesn't actually work. This
applies on top of it makes it work on my test Ebony machine.
This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll"
posted previously.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Two small fixes to IPoIB support for bonding:
1- copy header_ops from slave to bonding for IPoIB slaves
2- move release and destroy logic to UNREGISTER from GOING_DOWN
notifier to avoid double release
Set bonding to version 3.2.1.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Apparently poking the link status registers when autonegotiation
is running on the PHY might botch the PHY link on 80003es2lan
devices. While this is a very rare condition we can completely
avoid it alltogether by just using the MAC link bits to provide
the proper information to ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The xl_laa array is just 6 bytes long, so we should substract
10 from the index, like is also done some lines above already.
Signed-Off-By: Marcus Meissner <meissner@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A copy of struct net_device_stats now lives in struct net_device,
making in-driver copies a waste of memory.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
main change:
* greatly improve per-NIC probe diagnostic output. Similar to other
net drivers, print out MAC address, PHY info, and various hardware and
software flags that may be relevant.
other changes:
* similar to other net drivers, only print the initial version message
when we have found at least one board.
* don't bother to print error message when pci_enable_device() fails,
it will do so for us.
* use dev_printk() rather than printk() in nv_probe(). This gives
use a standardized output similar to the rest of the kernel, and
eliminates the need to manually print out PCI bus id.
* use DRV_NAME constant where appropriate
* clean struct pci_driver indentation
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (25 commits)
firewire: fw-cdev: reorder wakeup vs. spinlock
firewire: in-code doc updates.
firewire: a header cleanup
firewire: adopt read cycle timer ABI from raw1394
firewire: fw-ohci: check for misconfigured bus (phyID == 63)
firewire: fw-ohci: missing dma_unmap_single
firewire: fw-ohci: log posted write errors
firewire: fw-ohci: reorder includes
firewire: fw-ohci: fix includes
firewire: fw-ohci: enforce read order for selfID generation
firewire: fw-sbp2: use an own workqueue (fix system responsiveness)
firewire: fw-sbp2: expose module parameter for workarounds
firewire: fw-sbp2: add support for multiple logical units per target
firewire: fw-sbp2: always enable IRQs before calling command ORB callback
firewire: fw-core: local variable shadows a global one
firewire: optimize fw_core_add_address_handler
ieee1394: ieee1394_core.c: use DEFINE_SPINLOCK for spinlock definition
ieee1394: csr1212: proper refcounting
ieee1394: nodemgr: fix leak of struct csr1212_keyval
ieee1394: pcilynx: I2C cleanups
...
This patch kills ugly warnings when the "Improve SELinux performance
when ACV misses" patch.
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Signed-off-by: James Morris <jmorris@namei.org>
* We add ebitmap_for_each_positive_bit() which enables to walk on
any positive bit on the given ebitmap, to improve its performance
using common bit-operations defined in linux/bitops.h.
In the previous version, this logic was implemented using a combination
of ebitmap_for_each_bit() and ebitmap_node_get_bit(), but is was worse
in performance aspect.
This logic is most frequestly used to compute a new AVC entry,
so this patch can improve SELinux performance when AVC misses are happen.
* struct ebitmap_node is redefined as an array of "unsigned long", to get
suitable for using find_next_bit() which is fasted than iteration of
shift and logical operation, and to maximize memory usage allocated
from general purpose slab.
* Any ebitmap_for_each_bit() are repleced by the new implementation
in ss/service.c and ss/mls.c. Some of related implementation are
changed, however, there is no incompatibility with the previous
version.
* The width of any new line are less or equal than 80-chars.
The following benchmark shows the effect of this patch, when we
access many files which have different security context one after
another. The number is more than /selinux/avc/cache_threshold, so
any access always causes AVC misses.
selinux-2.6 selinux-2.6-ebitmap
AVG: 22.763 [s] 8.750 [s]
STD: 0.265 0.019
------------------------------------------
1st: 22.558 [s] 8.786 [s]
2nd: 22.458 [s] 8.750 [s]
3rd: 22.478 [s] 8.754 [s]
4th: 22.724 [s] 8.745 [s]
5th: 22.918 [s] 8.748 [s]
6th: 22.905 [s] 8.764 [s]
7th: 23.238 [s] 8.726 [s]
8th: 22.822 [s] 8.729 [s]
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Allow policy to select, in much the same way as it selects MLS support, how
the kernel should handle access decisions which contain either unknown
classes or unknown permissions in known classes. The three choices for the
policy flags are
0 - Deny unknown security access. (default)
2 - reject loading policy if it does not contain all definitions
4 - allow unknown security access
The policy's choice is exported through 2 booleans in
selinuxfs. /selinux/deny_unknown and /selinux/reject_unknown.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
It reduces the selinux overhead on read/write by only revalidating
permissions in selinux_file_permission if the task or inode labels have
changed or the policy has changed since the open-time check. A new LSM
hook, security_dentry_open, is added to capture the necessary state at open
time to allow this optimization.
(see http://marc.info/?l=selinux&m=118972995207740&w=2)
Signed-off-by: Yuichi Nakamura<ynakam@hitachisoft.jp>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
This patch reduces memory usage of SELinux by tuning avtab. Number of hash
slots in avtab was 32768. Unused slots used memory when number of rules is
fewer. This patch decides number of hash slots dynamically based on number
of rules. (chain length)^2 is also printed out in avtab_hash_eval to see
standard deviation of avtab hash table.
Signed-off-by: Yuichi Nakamura<ynakam@hitachisoft.jp>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
This duplicates the read cycle timer feature of raw1394 (added in Linux
2.6.21) in firewire-core's userspace ABI. The argument to the ioctl is
reordered though to ensure 32/64 bit compatibility.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Check NodeID.nodeNumber as per OHCI 1.1 clause 7.2.3.2. See also IEEE
1394a table 5B-1.
Also, demote the "node ID not valid" message from error to notification
as it is not an error condition.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
