The clk_mpll has long been moved into common clock code, remove the
code completely instead of the nasty #if 0 block.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move more of the core clocks that where left over from the last commit
as they are much more core to the system operation. This should allow
for easier tracking of any problems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C2443 clock code could easily make use of the clksrc implementation
in plat-samsung for many of the clocks. Make the clocks that easily move
to clksrc-clk over, update any initialisation and remove the old register
definitions from the header file (it is only being used once).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix a reference to regs-sys.h got missed in the reorganisation of
the Samsung platform headers targetted for 2.6.34.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks' commit cf9814eb (ARM: S3C64XX: Make audio device code built
unconditionally) made the struct devices for the audio blocks in the
S3C64xx series processors be built unconditionally but this change seems
to have gone AWOL in the various Samsung platform moves this release
cycle, causing link failures with machine drivers that rely on it.
Reintroduce the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The reorgs of the Samsung headers have moved the GPIO bank definitions
from plat/ to mach/ - the IIS driver needs to be updated to take care
of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 58bac7b8de failed to move the two
PLL files s3c2440-pll-12000000.c and s3c2440-pll-16934400.c, so place
these in arch/arm/mach-s3c2440 to fix this commit up.
As a note, these are not built by the default configuration and thus the
failure to move wasn't spotted until much later.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Set GPIO bits to pull the pins connected to LEDs for lower power mode.
We want all LEDs off when devices are in suspend.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:
arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This function gets only called from scoop_suspend() and scoop_resume() which are
only built in if we have CONFIG_PM set. Make it the same for check_scoop_reg().
This fixes the following warning:
arch/arm/common/scoop.c:143: warning: ‘check_scoop_reg’ defined but not used
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The IRQs for card detect and status change are currently hardcoded in
SA1111 PCMCIA driver, which can be actually obtained from the .irq[]
from 'struct sa1111_dev' to keep it generic.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Russell King