Setup generators for empty, random, and dummy bursts. This moves error
prone burst length handling out of the Transceiver and into the signal
processing core.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
At 4 samples per symbol, we don't need to maintain the 156/157 sample
slot structure to account for the GSM 156.25 sample burst length.
Set the 4 SPS Laurent modulator to ignore the guard interval setting
and always output 625 sample sized bursts. The EDGE 8-PSK modulator
already has this behavior.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Create EDGE slot type in the Transceiver. When EDGE mode is enabled
for a particular slot, blind detection will be performed by
correlating against EDGE followed by normal bursts if no EDGE burst
is found.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Setup correlator and detection process similar to the GMSK
receiver chain. Require 4 SPS sampling on both Rx and Tx paths
as 1 SPS sampling adds too much distoration for 8-PSK recovery.
Core receiver operations still run at 1 SPS with the exception
of fractional delay filtering, which runs at the higher rate.
Perform linear equalization to handle the Gaussian pulse
induced ISI. The fixed impulse response used for equalizer tap
calculation consists of combined EDGE pulse shape filter and
effects of the downsampling filter. Note that the non-adaptive
equalizer corrects for modulation induced band limiting and
does not account for or compensate for fading channel effects.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Allow setting the device to non single SPS sample rates - mainly
running at 4 SPS as the signal processing library does not support
other rates. Wider bandwith support is required on the receive path
to avoid 8-PSK bandlimiting distortion for EDGE.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
DFE equalizer is unused and has been experiencing code rot for
multiple years. The effect is a significant amount of baggage being
carried in the Transceiver and interfaces.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Samples per symbol used by the transceiver is not configurable through
the socket interface once running, so stop pretending like it could be.
Initialize all tables and midambles at start.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Patch f147b174 "sigproc: Make convolution and convert input buffers
immutable" changed the internal conversion interface with the addition
of the const type qualifier. This change was not reflected on ARM builds
which led to build failure. Add const qualifier to resolve build issue.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Certain pre-release versions of the B200mini used the B205 naming, which no
longer exists. Update device naming and detection to reflect current UHD
product names.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
UHD handles built in tick and floating point timestamp conversion
since version 003.005.004. This removes the need for separate UHD
timespec to tick conversion.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Commit 90f7a01d lost "return" statement. We also should account the fact that
offset can be negative.
We should return the tuning request immediately after
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Rounding error introduced oscilating timing advance error by regularly
overwriting one bit and then skipping one bit.
This commit also adds an error message to show up in logs if this ever
happens again.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
As a side change - get rid of passing toa and amp arguments as pointers and use
references instead.
The commit doesn't change behaviour, but makes the code cleaner.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
We can't rely on an assumption that if we can't decode a burst - it's noise.
There are many rasons why we can't decode a burst even if it's well above the
noise level. Just one example is a RACH burst which can be overlapped with
another RACH burst up to a level both are completely unrecognizable. Another
example is when a burst is destroyed by bad multi-path.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
It does more harm than good. the current noise calculation is too error
prone, so we can't trust it. And we end up loosing perfectly good bursts
because of that.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
There are two primary changes in this commit:
1) Return values of detect functions changed form bool to int to actually pass
the return value from the inner function and notify higher levels about clipping.
Previously the information was lost due to conversion to bool.
2) Clipping level is not the final verdict now. We still try to demod a burst
and mark it as clipped only if the level is above the clipping level AND we can't
demod it. The reasoning for this is that in real life we want to do as much as
possible to demod the burst, because we want to get as much from our dynamic
range as possible. So a little bit of clipping is fine and is expected. We just
don't want too much of it to break our demod.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
R&S CMD57 complains about the start phase of bursts, particularly it shows
-15 to -30 deg of error for the bit 0.5 position (start tail bit). This patch
makes it happy. ETSI TS 145 004 section 2.2 describes this: "Before the first
bit of the bursts as defined in 3GPP TS 45.002 enters the modulator,
the modulator has an internal state as if a modulating bit stream consisting
of consecutive ones (di = 1) had entered the differential encoder."
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Receive thread receives data from the device, which is a more stable source of
clocking than the transmit side. If transmit side has a hiccup, osmo-trx doesn't
send the clock indication, and transmit side is getting completely lost in time.
With this patch we ensure that clock indication keeps coming.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Filler types was of "bool" type, which prevented it from taking values greter
than 1. And RAND filler type has integer value of 2, which was casted to 1 on
assigning, which led to a normal filler table being used instead of the RAND
one.
When we enable DEBUG logging level, syslog gets Gb's of data and can completely
exhaust the file system free space. Now we can just enable it. This is not to
say that logging to syslog it just not very useful in general.
Previous behaviour used UHD command line args string for device search,
but did not apply the values to the device constructor. Now use the user
passed args string for both find and device construction.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
New UHD versions support split configuration of Tx gain stages.
We utilize this to set the gain configuration, optimal for
the Tx signal quality. From our measurements, VGA1 must be
18dB plus-minus one and VGA2 is the best when 23dB or lower.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Setup '--with-sse' option to check system capabilities by default, but
allow disabling by the user. Selective SSE build options can be
controlled by the user by defining specific HAVE_SSE options.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Alert user of overdriven burst input indicated by a positive
threshold detector result. This indication serves as notification
that the receive RF gain level is too high for the configured
transceiver setup.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
This will shutup automake and make it stop complaining about the
following subdirectory warnings.
"warning: source file 'common/fft.c' is in a
subdirectory, but option 'subdir-objects' is disabled"
Signed-off-by: Tom Tsou <tom@tsou.cc>
Non-zero buffer indices may lead to uplink/downlink timing offset
during repeated start/stop cycles. Mainly affects USRP2 and other
resampled devices that rely on the buffer to absorb sample block
sizes that are not multiples of the burst size.
Signed-off-by: Tom Tsou <tom.tsou@ettus.com>
Tom Tsou