The token was compared with the configured one but only up to a
user supplied length. Compare the token sizes and then use memcmp
for the actual comparison to make sure to compare the right ammount
of characters.
There is no unit-test but there should be one.
For USSD we remember that it is a supplementary service but this
means we sent no CM Service Reject down to the subscriber. Treat
NAT_CON_TYPE_CM_SERV_REQ and NAT_CON_TYPE_SSA the same and send
a cm service reject.
Do the auth check in bsc_nat_filter_sccp_cr, remove the cause from
the signature again. For the bsc_nat_filter_dt restructure the flow
but leave the auth inside the id response message.
Return 1 when the IMSI has been extracted as indicator for running
the auth check. 1 has not been used before and is safe to be used
as this indicator.
In preparation for another kind of black-list allow the filter code
to decide how the connection should be rejected. Introduce a new struct
that will carry the reject causes for certain operations.
Move to the control command handling out of the main file into
a dedicated module. There are still some calls embedded into the
main code but it will be moved soon.
The test cases were failing on 64bit systems because the sizeof
code operated on the pointer size which is 8 and longer than the
size that was intended to be used for comparing it.
The commands net.<netid>.bsc.<bscid>.* are now forwarded to the
appropriate osmo-bsc. <netid> for now is just 0. <bscid> is not the LAC
anymore (since that could be ambiguous), but instead the number as
configured in bsc-nat.cfg
nat: Catch up with controlif_setup API change
We now save a control handle reference in the nat
osmo-bsc: Catch up with controlif_setup API change
We now save a control handle reference in the gsm network
Some nodes below 'config' didn't have ournode_exit / ournode_end,
and thus were not able to properly perform this function. exit should
always only go back one level, while end drops us back to ENABLE_NODE.
The prompt now represents the nesting level, and there's one consistent
space after the final prompt character (typically #).
Introduce number rewriting of SMS-SUBMIT. Introduce a new list,
move code around to help with finding a new number, somehow the
number encoding for TP-DA is borked, 03.40 references 04.11 but
the length appears to be strlen(number) without taken the type
field into account.
Match IMSI and destination address against a set of entries, if it
is matching the header will be modified and no sender report will be
requested. Change the test case to request the sender report and then
verify that this bit is reset to 0.
Ubuntu 11.10 has changed some linker/compiler flags. Some fixes for this
can be seen here[1]. In general the to be linked libs need to be moved into
the LDADD section of parameters. This is with the old BFD linker (not gold).
This is likely to end in some ping-pong with other versions of the linker.
[1] https://bugs.launchpad.net/ubuntu/+source/nis/+bug/771034
Errors:
/usr/bin/ld.bfd.real: bsc_hack.o: undefined reference to symbol 'osmo_init_ignore_signals'
/usr/bin/ld.bfd.real: note: 'osmo_init_ignore_signals' is defined in DSO /home/ich/install/openbsc/lib/libosmocore.so so try adding it to the linker command line
/home/ich/install/openbsc/lib/libosmocore.so: could not read symbols: Invalid operation
...
../../src/libbsc/libbsc.a(rest_octets.o):/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:381: more undefined references to `bitvec_set_bit' follow
../../src/libbsc/libbsc.a(rest_octets.o): In function `rest_octets_si13':
/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:382: undefined reference to `bitvec_set_uint'
/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:383: undefined reference to `bitvec_set_uint'
/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:385: undefined reference to `bitvec_set_bit'
/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:402: undefined reference to `bitvec_set_bit'
/home/ich/source/gsm/openbsc/openbsc/src/libbsc/rest_octets.c:403: undefined reference to `bitvec_set_uint'
Move the regexp parsing code from the NAT to libcommon as it will
be used by the NAT and BSC code. This also adds the #include <regex.h>
include to gsm_data. This header should be split up.
This is a big patch that ports openBSC over libosmo-abis.
Sorry, the changes that are included here are all dependent
of libosmo-abis, splitting them into smaller pieces would
leave the repository in some intermediate state, which is
not desired.
The main changes are:
- The directory libabis/ has been removed as it now lives in
libosmo-abis.
- new configuration file format for nanoBTS and HSL femto, we
need to define the virtual e1_line and attach it to the OML
link.
- all the existing BTS drivers (nanoBTS, hsl femto, Nokia site,
BS11 and rbs2000) now use the new libosmo-abis framework.
- use r232 input driver available in libosmo-abis for bs11_config.
- use ipa_msg_recv instead of old ipaccess_read_msg function.
- delete definition of gsm_e1_subslot and input_signal_data.
These structures now lives in libosmo-abis.
Most of this patch are deletions of libabis/ which has been
moved to libosmo-abis.
This patch also modifies openBSC to use all the new definitions
available in libosmocore and libosmo-abis. In order to do that,
we have replaced the following:
- DINP, DMI, DMIB and DMUX by their respective DL* correspondences.
- SS_GLOBAL by SS_L_GLOBAL
- SS_INPUT by SS_L_INPUT
- S_GLOBAL_SHUTDOWN by S_L_GLOBAL_SHUTDOWN
- SS_INPUT by SS_L_INPUT
- S_INP_* by S_L_INP_* sub-signals
- E1INP_NODE by L_E1INP_NODE vty node
This patch has been tested with:
- one nanoBTS
- the HSL femto with the examples available under libosmo-abis
- BS11 with both dahdi and misdn drivers.
Holger Hans Peter Freyther
Harald Welte