The interface can be accessed through CTRL and a socket. But currently
it is only available when the socket interface has been configured.
Create the interface all the time but only listen on the socket when
a path has been specified.
Rename this function to bsc_send_ussd_no_srv() since it's a rather
specialised function and not a generic USSD notification function.
Sponsored-by: On-Waves ehf
The MS do not show the USSD messages yet. This patch modifies the
implementation to insert a CM Service Accept to finish the
establishment of the MM connection according to 3GPP TS 04.10/3.2.1
before the USSD notification is sent.
This fix has been tested with a Blackberry phone that has shown
an ussd_grace_txt after rf_locked has been set to '1'. Without this
patch, that message wasn't shown. The phone has sent a CC Setup
and other messages before processing the channel release message sent
by the BSC, but these messages have not been forwarded to the MSC (as
expected).
Ticket: OW#957
Sponsored-by: On-Waves ehf
The MS do not show the USSD messages yet. This patch modifies the
implementation to insert a CM Service Accept before the ussdNotify
to finish the establishment of the MM connection according to
3GPP TS 04.10/3.2.1.
This fix has been tested with a Blackberry phone that has shown
an ussd_grace_txt after rf_locked has been set to '1'. Without this
patch, that message wasn't shown. The phone has sent a CC Setup
and other messages before processing the channel release message sent
by the BSC, but these messages have not been forwarded to the MSC (as
expected).
Ticket: OW#957
Sponsored-by: On-Waves ehf
Remove ournode_exit_cmd, ournode_end_cmd, and bsc_install_default()
since this functionality is provided by the current libosmocore.
Replace calls to bsc_install_default() by call to
vty_install_default() with the following semantic patch:
@rule1@
expression N;
@@
- bsc_install_default(N);
+ vty_install_default(N);
Ticket: OW#952
Sponsored-by: On-Waves ehf
This adds a per BTS control command 'timezone' which expects a value
of the format '<hours>,<mins>,<dst>' or 'off' to set the value of
bts->tz. It has the same functionality like the existing VTY command
'timezone' in network/bts.
Sponsored-by: On-Waves ehf
Ticket: OW#978
This adds in-place patching of the time information in the
MM INFORMATION message. The timezone in the 'Local time zone' and
the 'Universal time and local time zone' information elements
and the offset in the 'Network Daylight Saving Time' information
element are optionally set.
The new values are determined by the 'timezone' vty command in the
config_net_bts node. That command is extended by an optional
DST offset parameter.
Tests are provided for the vty part and for the plain
bsc_scan_msc_msg() function.
Sponsored-by: On-Waves ehf
Ticket: OW#978
This stores the last SET rf_locked control command along with a
timestamp. The 'show network' vty command is extended to show
this information.
Ticket: OW#659
Send an USSD message to the mobile station requesting a connection
for a call or a SMS when the link to the MSC is down or in the
grace period.
The messages can be set (and this feature activated) by setting
bsc/missing-msc-text resp. msc/bsc-grace-text via the vty.
The generation of both messages has been tested manually.
Ticket: OW#957
Add bsc_install_default() and replace all install_default()
This patch adds bsc_install_default() which calls install_default()
and add 'exit' and 'end'. All other calls to install_default() are
replaced by calls to bsc_install_default().
Since 'exit' and 'end' are now added automatically to each node, the
explicit registrations of these commands are removed by this patch,
too.
The related tests succeed now without work-arounds (except for the
'config' node itself which is part of libosmocore).
Addresses:
osmo_bsc_sccp.c:280:2: warning: implicit declaration of function ‘gsm0480_send_ussdNotify’ [-Wimplicit-function-declaration]
osmo_bsc_sccp.c:281:2: warning: implicit declaration of function ‘gsm0480_send_releaseComplete’ [-Wimplicit-function-declaration]
Change '%s(bsc)#' to '%s(config-bsc)# '. The missing trailing blank
breaks osmopy's VTYInteract.command() because the blank is contained
in the end patterns which are checked to decide whether to leave the
select loop. Thus trying to execute the 'bsc' command there blocks
the test script forever.
Send an USSD message on each MS connection if the connection to
the MSC has been lost.
Add a vty config command 'bsc-msc-loss-txt' in 'config-msc' to set
the notification string and to enable the feature.
Ticket: OW#957
bsc_api.c:417:3: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 7 has type ‘unsigned int’ [-Wformat]
bsc_api.c: In function ‘handle_ass_fail’:
bsc_api.c:458:3: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 7 has type ‘unsigned int’ [-Wformat]
db.c: In function ‘db_sync_subscriber’:
db.c:785:3: warning: format ‘%i’ expects argument of type ‘int’, but argument 8 has type ‘time_t’ [-Wformat]
osmo_msc.c: In function ‘msc_release_connection’:
osmo_msc.c:145:20: warning: unused variable ‘trans’ [-Wunused-variable]
smpp_smsc.c: In function ‘link_accept_cb’:
smpp_smsc.c:891:24: warning: assignment from incompatible pointer type [enabled by default]
smpp_smsc.c:271:1: warning: ‘esme_by_system_id’ defined but not used [-Wunused-function]
smpp_openbsc.c: In function ‘smpp_openbsc_init’:
smpp_openbsc.c:545:2: warning: implicit declaration of function ‘smpp_vty_init’ [-Wimplicit-function-declaration]
osmo_bsc_ctrl.c: In function ‘verify_bts_loc’:
osmo_bsc_ctrl.c:340:19: warning: variable ‘height’ set but not used [-Wunused-but-set-variable
smpp_mirror.c: In function ‘main’:
smpp_mirror.c:297:2: warning: implicit declaration of function ‘osmo_init_logging’ [-Wimplicit-function-declaration]
It was possible that the tmp was strduped but not freed, e.g. when
the number of commas was not right. It would evenutally be freed at
the time the cmd is freed thanks to the talloc hierachy.
Katerina pointed out that some nodes are not fully documented and
proposed some messages. The token/timeout messages were correct, I
have modified the other messages. I removed the full-stop from the
PING/PONG documentation as we are normally not using a full sentence.
The RF lock excluded BTS was not paged at all. Now forward the
paging message to the handler and call a function that will check
if this LAC can be paged right now. Introduce a new paging method
that allows to page on a dedicated bts, refactor the code to use
this method for paging.
When introducing the exclude for the BTS lock the RF stayed up but
all connections were immediately released. Optionally pass the BTS
as second parameter and check the exclude bit.
Tested-with: rf-lock-exclude/RFLockExcludeTest.st
For short IP failures we want the RF to stay up and wait for
the re-connect but in case the A-link is gone too long it is
good to switch off the RF and wait for commands to enable it
again.
Handle the mr_config request and set the AMR multirate config for
the given MSC. Initialize the mr_config with the AMR5.9 default we
have been using until now.
When we are asked to route calls on a local link and
the link is not available we would crash when trying
to send a packet over a deadline. When we have decided
to move a connection it is guranteed that the current
SCCP connection will vanish, we either migrate to another
MSC or the RSL/subscriber connection will be closed.
Inspect the CC Setup messages and if the dialed number is matching
the regexp of the local MSC the connection will be rerouted. The
original MSC will get a GSM0808 CLEAR REQUEST, a new connection with
a CC Setup message will be opened.
This was reported by Kevin when he was testing handover. The problem
is the order of the signal handlers for S_ABISIP_CRCX_ACK. Right now
the handover signal handler is called before the one inside the libmsc
gsm_04_08.c. This means S_HANDOVER_ACK is signalled _before_ there is a
rtp socket created for the channel. The result is that the MDCX will
never be sent and the called will not be properly switched _after_ the
handover detection.
I do not want to play with the order of signal handlers, remove the
CRCX ack handling from the handover_logic.c and force the NITB (and
later the BSC) to check if the lchan is involved with a handover and
do the switching in there. This means right now we do what two signal
handlers did in one.
Reproduced and tested with the FakeBTS Handover test.
Log message:
<0004> abis_rsl.c:1954 (bts=1,trx=0,ts=3,ss=0) IPAC_CRCX_ACK ...
<000c> gsm_04_08.c:1400 no RTP socket for new_lchan
<001a> rtp_proxy.c:533 rtp_socket_create(): success
<001a> rtp_proxy.c:615 rtp_socket_bind(rs=0x48703c8, IP=0.0.0.0): ...