libosmogsm is a new library that is distributed in the libosmocore.
Now, openbsc depends on it. This patch gets openbsc with this
change.
This patch also rewrites all include path to the new
osmocom/[gsm|core]
Signed-off-by: Pablo Neira Ayuso <pablo@gnumonks.org>
The new structure divides the code into a number of libraries
for the BSC core functionality, MSC core functionality, Abis transport,
TRAU and other bits.
This doesn't introduce any functional code change but simply moves
around files and alters Makefile.am accordingly.
Next step would be to disentangle a lot of the inter-library
dependencies and make the individual bits of code more independent.
bsc_init.c was a big mess even only for two supported BTS models,
so before adding more BTS types, this needs a cleanup.
All the BTS specific code from bsc_init.c has now moved into
bts_{siemens_bs11,ipaccess_nanobts}.c
This has required that input_event() and nm_state_event() get both
converted to proper libosmocore signals instead of referencing external
symbols.
The reason for this is quite simple: We want to make sure anyone
running a customized version of OpenBSC to operate a network will
have to release all custom modifiations to the source code.
Currently the nanoBTS bootstrap code requires a high delay
otherwise we are not bringing the device up properly. Changing
the init code turns out harder than it seems like. So this is
a workaround for that to allow a high speed RSL/OML connection
after the bringup.
The line driver can have a default TS delay. It is set to the
current default for the nanoBTS and the BS11. For the ipaccess
case we will set the delay lower for the RSL connection and
inside the ipaccess-config we can set it low right away to
have fast firmware flashing and such.
... while asking the BTS to perform tests for us. The length of the
ARFCN whitelist is the actual length in bytes, not the number of 16bit
ARFCN numbers.
Also, implement a limit, either by rxlevel or by number of ARFCN
that should end up in the whitelist.
Also, we now re-start the network listen test after it has finished,
so if you run a test from ipaccess-find, the test will get re-started
and re-started all the time.
there are now human-readable names so you can do something like
ipaccess-config -U dhcp-enabled -S static-ip -S static-gw 192.168.100.120
to unset DHCP and to set static IP and gateway attributes.
This looks so much better than the *cur++ type code.
Also, we now terminate ipaccess-config once the NV flags or Unit ID have
been set, not just for the OML IP address.
We will tell the BTS where we are listening, but the ACK
will return the original settings... this should make it
possible to intercept the GPRS stream..
This is a good interim solution for messages not handled by us,
right now this would include the NVRAM attributes that I do not
feel like caching right now.
For the multi TRX setup we will need to specify the right trx->nr
to be able to flash the BTS. For the BS11 case we are ignoring the
additional argument.
Send the IPA Restart to a given BTS/TRX, change the signal callbacks
to carry the trx instead of the BTS so we have an easy access to the
right TRX and change the ipaccess-config to use that TRX. This is
fixing the restart with a multi TRX setup.
Even if we have the msg->trx, use the gsm_bts_trx_by_nr and get
the TRX from the fom header. This is because the OpenBSC and the
BTS numbering might not match for the multi TRX case.
Currently we are connecting to the BTS and once the OML is established
we are bootstrapping the OML. This does not work for a multi TRX setup
as we will need to use a trx_nr != 0 for it.
Change the code to wait for a message (in this case NM OC_BASEBAND_TRANSC)
to detect the trx_nr used by the BTS and then use that TRX to bootstrap
the network.
I have tested setting the unit id on a single and multi trx system for
the first and second trx.
The logging/debugging code is generic enough to move it into libosmocore
while keeping OpenBSC specific definitions in openbsc itself.
This commit uses the logging support present in libosmocore-0.1.2,
you will have to update your library to this version.
Currently one has to put -w in front of -f to really write the
firmware file to disk. Change the config handling to first take
all parameters and then execute on them. This means -f can now
be used with any other parameter.
Pablo Neira Ayuso
Harald Welte