osmo-msc/src/libmsc/e_link.c

380 lines
12 KiB
C
Raw Permalink Normal View History

large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
/* E-interface messaging over a GSUP connection */
/*
* (C) 2019 by sysmocom - s.m.f.c. GmbH <info@sysmocom.de>
* All Rights Reserved
*
* SPDX-License-Identifier: AGPL-3.0+
*
* Author: Neels Hofmeyr
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU Affero General Public License as published by
* the Free Software Foundation; either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Affero General Public License for more details.
*
* You should have received a copy of the GNU Affero General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <osmocom/core/fsm.h>
#include <osmocom/gsupclient/gsup_client.h>
#include <osmocom/msc/gsm_data.h>
#include <osmocom/msc/gsup_client_mux.h>
#include <osmocom/msc/e_link.h>
#include <osmocom/msc/msub.h>
#include <osmocom/msc/msc_roles.h>
#include <osmocom/msc/vlr.h>
#include <osmocom/msc/ran_infra.h>
#include <osmocom/msc/msc_a.h>
#include <osmocom/msc/msc_a_remote.h>
#include <osmocom/msc/msc_i.h>
#include <osmocom/msc/msc_i_remote.h>
#include <osmocom/msc/msc_t.h>
#include <osmocom/msc/msc_t_remote.h>
#define LOG_E_LINK(e_link, level, fmt, args...) \
LOGPFSML(e_link->msc_role, level, fmt, ##args)
#define LOG_E_LINK_CAT(e_link, ss, level, fmt, args...) \
LOGPFSMSL(e_link->msc_role, ss, level, fmt, ##args)
void e_link_assign(struct e_link *e, struct osmo_fsm_inst *msc_role)
{
struct msc_role_common *c;
if (e->msc_role) {
c = e->msc_role->priv;
if (c->remote_to == e) {
c->remote_to = NULL;
msub_update_id(c->msub);
}
}
c = msc_role->priv;
e->msc_role = msc_role;
c->remote_to = e;
msub_update_id(c->msub);
LOG_E_LINK(e, LOGL_DEBUG, "Assigned E-link to %s\n", e_link_name(e));
}
struct e_link *e_link_alloc(struct gsup_client_mux *gcm, struct osmo_fsm_inst *msc_role,
const uint8_t *remote_name, size_t remote_name_len)
{
struct e_link *e;
struct msc_role_common *c = msc_role->priv;
size_t use_len;
large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
/* use msub as talloc parent, so we can move an e_link from msc_t to msc_i when it is established. */
e = talloc_zero(c->msub, struct e_link);
if (!e)
return NULL;
e->gcm = gcm;
/* FIXME: this is a braindamaged duality of char* and blob, which we can't seem to get rid of easily.
* See also osmo-hlr change I01a45900e14d41bcd338f50ad85d9fabf2c61405 which resolved this on the
* osmo-hlr side, but was abandoned. Not sure which way is the right solution. */
/* To be able to include a terminating NUL character when sending the IPA name, append one if there is none yet.
* Current osmo-hlr needs the terminating NUL to be included. */
use_len = remote_name_len;
if (remote_name[use_len-1] != '\0')
use_len++;
e->remote_name = talloc_size(e, use_len);
large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
OSMO_ASSERT(e->remote_name);
memcpy(e->remote_name, remote_name, remote_name_len);
e->remote_name[use_len-1] = '\0';
e->remote_name_len = use_len;
large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
e_link_assign(e, msc_role);
return e;
}
void e_link_free(struct e_link *e)
{
if (!e)
return;
if (e->msc_role) {
struct msc_role_common *c = e->msc_role->priv;
if (c->remote_to == e)
c->remote_to = NULL;
}
talloc_free(e);
}
/* Set up IMSI, source and destination names in given gsup_msg struct. */
int e_prep_gsup_msg(struct e_link *e, struct osmo_gsup_message *gsup_msg)
{
struct msc_role_common *c;
struct vlr_subscr *vsub;
const char *local_msc_name = NULL;
if (e->gcm && e->gcm->gsup_client && e->gcm->gsup_client->ipa_dev) {
local_msc_name = e->gcm->gsup_client->ipa_dev->serno;
if (!local_msc_name)
local_msc_name = e->gcm->gsup_client->ipa_dev->unit_name;
}
if (!local_msc_name) {
LOG_E_LINK(e, LOGL_ERROR, "Cannot prep E-interface GSUP message: no local MSC name defined\n");
return -ENODEV;
}
c = e->msc_role->priv;
vsub = c->msub->vsub;
*gsup_msg = (struct osmo_gsup_message){
.message_class = OSMO_GSUP_MESSAGE_CLASS_INTER_MSC,
.source_name = (const uint8_t*)local_msc_name,
.source_name_len = strlen(local_msc_name)+1, /* include terminating nul */
large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
.destination_name = (const uint8_t*)e->remote_name,
.destination_name_len = e->remote_name_len, /* the nul here is also included, from e_link_alloc() */
large refactoring: support inter-BSC and inter-MSC Handover 3GPP TS 49.008 '4.3 Roles of MSC-A, MSC-I and MSC-T' defines distinct roles: - MSC-A is responsible for managing subscribers, - MSC-I is the gateway to the RAN. - MSC-T is a second transitory gateway to another RAN during Handover. After inter-MSC Handover, the MSC-I is handled by a remote MSC instance, while the original MSC-A retains the responsibility of subscriber management. MSC-T exists in this patch but is not yet used, since Handover is only prepared for, not yet implemented. Facilitate Inter-MSC and inter-BSC Handover by the same internal split of MSC roles. Compared to inter-MSC Handover, mere inter-BSC has the obvious simplifications: - all of MSC-A, MSC-I and MSC-T roles will be served by the same osmo-msc instance, - messages between MSC-A and MSC-{I,T} don't need to be routed via E-interface (GSUP), - no call routing between MSC-A and -I via MNCC necessary. This is the largest code bomb I have submitted, ever. Out of principle, I apologize to everyone trying to read this as a whole. Unfortunately, I see no sense in trying to split this patch into smaller bits. It would be a huge amount of work to introduce these changes in separate chunks, especially if each should in turn be useful and pass all test suites. So, unfortunately, we are stuck with this code bomb. The following are some details and rationale for this rather huge refactoring: * separate MSC subscriber management from ran_conn struct ran_conn is reduced from the pivotal subscriber management entity it has been so far to a mere storage for an SCCP connection ID and an MSC subscriber reference. The new pivotal subscriber management entity is struct msc_a -- struct msub lists the msc_a, msc_i, msc_t roles, the vast majority of code paths however use msc_a, since MSC-A is where all the interesting stuff happens. Before handover, msc_i is an FSM implementation that encodes to the local ran_conn. After inter-MSC Handover, msc_i is a compatible but different FSM implementation that instead forwards via/from GSUP. Same goes for the msc_a struct: if osmo-msc is the MSC-I "RAN proxy" for a remote MSC-A role, the msc_a->fi is an FSM implementation that merely forwards via/from GSUP. * New SCCP implementation for RAN access To be able to forward BSSAP and RANAP messages via the GSUP interface, the individual message layers need to be cleanly separated. The IuCS implementation used until now (iu_client from libosmo-ranap) did not provide this level of separation, and needed a complete rewrite. It was trivial to implement this in such a way that both BSSAP and RANAP can be handled by the same SCCP code, hence the new SCCP-RAN layer also replaces BSSAP handling. sccp_ran.h: struct sccp_ran_inst provides an abstract handler for incoming RAN connections. A set of callback functions provides implementation specific details. * RAN Abstraction (BSSAP vs. RANAP) The common SCCP implementation did set the theme for the remaining refactoring: make all other MSC code paths entirely RAN-implementation-agnostic. ran_infra.c provides data structures that list RAN implementation specifics, from logging to RAN de-/encoding to SCCP callbacks and timers. A ran_infra pointer hence allows complete abstraction of RAN implementations: - managing connected RAN peers (BSC, RNC) in ran_peer.c, - classifying and de-/encoding RAN PDUs, - recording connected LACs and cell IDs and sending out Paging requests to matching RAN peers. * RAN RESET now also for RANAP ran_peer.c absorbs the reset_fsm from a_reset.c; in consequence, RANAP also supports proper RESET semantics now. Hence osmo-hnbgw now also needs to provide proper RESET handling, which it so far duly ignores. (TODO) * RAN de-/encoding abstraction The RAN abstraction mentioned above serves not only to separate RANAP and BSSAP implementations transparently, but also to be able to optionally handle RAN on distinct levels. Before Handover, all RAN messages are handled by the MSC-A role. However, after an inter-MSC Handover, a standalone MSC-I will need to decode RAN PDUs, at least in order to manage Assignment of RTP streams between BSS/RNC and MNCC call forwarding. ran_msg.h provides a common API with abstraction for: - receiving events from RAN, i.e. passing RAN decode from the BSC/RNC and MS/UE: struct ran_dec_msg represents RAN messages decoded from either BSSMAP or RANAP; - sending RAN events: ran_enc_msg is the counterpart to compose RAN messages that should be encoded to either BSSMAP or RANAP and passed down to the BSC/RNC and MS/UE. The RAN-specific implementations are completely contained by ran_msg_a.c and ran_msg_iu.c. In particular, Assignment and Ciphering have so far been distinct code paths for BSSAP and RANAP, with switch(via_ran){...} statements all over the place. Using RAN_DEC_* and RAN_ENC_* abstractions, these are now completely unified. Note that SGs does not qualify for RAN abstraction: the SGs interface always remains with the MSC-A role, and SGs messages follow quite distinct semantics from the fairly similar GERAN and UTRAN. * MGW and RTP stream management So far, managing MGW endpoints via MGCP was tightly glued in-between GSM-04.08-CC on the one and MNCC on the other side. Prepare for switching RTP streams between different RAN peers by moving to object-oriented implementations: implement struct call_leg and struct rtp_stream with distinct FSMs each. For MGW communication, use the osmo_mgcpc_ep API that has originated from osmo-bsc and recently moved to libosmo-mgcp-client for this purpose. Instead of implementing a sequence of events with code duplication for the RAN and CN sides, the idea is to manage each RTP stream separately by firing and receiving events as soon as codecs and RTP ports are negotiated, and letting the individual FSMs take care of the MGW management "asynchronously". The caller provides event IDs and an FSM instance that should be notified of RTP stream setup progress. Hence it becomes possible to reconnect RTP streams from one GSM-04.08-CC to another (inter-BSC Handover) or between CC and MNCC RTP peers (inter-MSC Handover) without duplicating the MGCP code for each transition. The number of FSM implementations used for MGCP handling may seem a bit of an overkill. But in fact, the number of perspectives on RTP forwarding are far from trivial: - an MGW endpoint is an entity with N connections, and MGCP "sessions" for configuring them by talking to the MGW; - an RTP stream is a remote peer connected to one of the endpoint's connections, which is asynchronously notified of codec and RTP port choices; - a call leg is the higher level view on either an MT or MO side of a voice call, a combination of two RTP streams to forward between two remote peers. BSC MGW PBX CI CI [MGW-endpoint] [--rtp_stream--] [--rtp_stream--] [----------------call_leg----------------] * Use counts Introduce using the new osmo_use_count API added to libosmocore for this purpose. Each use token has a distinct name in the logging, which can be a globally constant name or ad-hoc, like the local __func__ string constant. Use in the new struct msc_a, as well as change vlr_subscr to the new osmo_use_count API. * FSM Timeouts Introduce using the new osmo_tdef API, which provides a common VTY implementation for all timer numbers, and FSM state transitions with the correct timeout. Originated in osmo-bsc, recently moved to libosmocore. Depends: Ife31e6798b4e728a23913179e346552a7dd338c0 (libosmocore) Ib9af67b100c4583342a2103669732dab2e577b04 (libosmocore) Id617265337f09dfb6ddfe111ef5e578cd3dc9f63 (libosmocore) Ie9e2add7bbfae651c04e230d62e37cebeb91b0f5 (libosmo-sccp) I26be5c4b06a680f25f19797407ab56a5a4880ddc (osmo-mgw) Ida0e59f9a1f2dd18efea0a51680a67b69f141efa (osmo-mgw) I9a3effd38e72841529df6c135c077116981dea36 (osmo-mgw) Change-Id: I27e4988e0371808b512c757d2b52ada1615067bd
2018-12-07 13:47:34 +00:00
};
if (vsub)
OSMO_STRLCPY_ARRAY(gsup_msg->imsi, vsub->imsi);
return 0;
}
int e_tx(struct e_link *e, const struct osmo_gsup_message *gsup_msg)
{
LOG_E_LINK_CAT(e, DLGSUP, LOGL_DEBUG, "Tx GSUP %s to %s\n",
osmo_gsup_message_type_name(gsup_msg->message_type),
e_link_name(e));
return gsup_client_mux_tx(e->gcm, gsup_msg);
}
const char *e_link_name(struct e_link *e)
{
return osmo_escape_str((const char*)e->remote_name, e->remote_name_len);
}
static struct msub *msc_new_msc_t_for_handover_request(struct gsm_network *net,
const struct osmo_gsup_message *gsup_msg)
{
struct ran_infra *ran;
struct msub *msub;
struct msc_a *msc_a;
struct vlr_subscr *vsub;
switch (gsup_msg->an_apdu.access_network_proto) {
case OSMO_GSUP_ACCESS_NETWORK_PROTOCOL_TS3G_48006:
ran = &msc_ran_infra[OSMO_RAT_GERAN_A];
break;
case OSMO_GSUP_ACCESS_NETWORK_PROTOCOL_TS3G_25413:
ran = &msc_ran_infra[OSMO_RAT_UTRAN_IU];
break;
default:
ran = NULL;
break;
}
if (!ran || !ran->ran_dec_l2) {
LOGP(DLGSUP, LOGL_ERROR, "Cannot handle AN-proto %s\n",
an_proto_name(gsup_msg->an_apdu.access_network_proto));
return NULL;
}
msub = msub_alloc(net);
/* To properly compose GSUP messages going back to the remote peer, make sure the incoming IMSI is set in a
* vlr_subscr associated with the msub. */
vsub = vlr_subscr_find_or_create_by_imsi(net->vlr, gsup_msg->imsi, __func__, NULL);
msub_set_vsub(msub, vsub);
vlr_subscr_put(vsub, __func__);
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "New subscriber for incoming inter-MSC Handover Request\n");
msc_a = msc_a_remote_alloc(msub, ran, gsup_msg->source_name, gsup_msg->source_name_len);
if (!msc_a) {
osmo_fsm_inst_term(msub->fi, OSMO_FSM_TERM_REQUEST, NULL);
return NULL;
}
LOG_MSC_A_REMOTE_CAT(msc_a, DLGSUP, LOGL_DEBUG, "New subscriber for incoming inter-MSC Handover Request\n");
return msub;
}
static bool name_matches(const uint8_t *name, size_t len, const uint8_t *match_name, size_t match_len)
{
if (!match_name)
return !name || !len;
if (len != match_len)
return false;
return memcmp(name, match_name, len) == 0;
}
static bool e_link_matches_gsup_msg_source_name(const struct e_link *e, const struct osmo_gsup_message *gsup_msg)
{
return name_matches(gsup_msg->source_name, gsup_msg->source_name_len, e->remote_name, e->remote_name_len);
}
static int msc_a_i_t_gsup_rx(struct gsup_client_mux *gcm, void *data, const struct osmo_gsup_message *gsup_msg)
{
struct gsm_network *net = data;
struct vlr_instance *vlr = net->vlr;
struct vlr_subscr *vsub;
struct msub *msub;
struct osmo_fsm_inst *msc_role = NULL;
struct e_link *e;
struct msc_role_common *c;
int i;
OSMO_ASSERT(net);
vsub = vlr_subscr_find_by_imsi(vlr, gsup_msg->imsi, __func__);
if (vsub)
LOGP(DLGSUP, LOGL_DEBUG, "Found VLR entry for IMSI %s\n", gsup_msg->imsi);
msub = msub_for_vsub(vsub);
if (msub)
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "Found already attached subscriber for IMSI %s\n",
gsup_msg->imsi);
if (vsub) {
vlr_subscr_put(vsub, __func__);
vsub = NULL;
}
/* Only for an incoming Handover Request: create a new remote-MSC-A as proxy for the MSC-A that is sending the
* Handover Request */
if (!msub && gsup_msg->message_type == OSMO_GSUP_MSGT_E_PREPARE_HANDOVER_REQUEST) {
msub = msc_new_msc_t_for_handover_request(net, gsup_msg);
}
if (!msub) {
LOGP(DLGSUP, LOGL_ERROR, "%s: Cannot find subscriber for IMSI %s\n",
__func__, osmo_quote_str(gsup_msg->imsi, -1));
return -EINVAL;
}
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "Rx GSUP %s\n", osmo_gsup_message_type_name(gsup_msg->message_type));
e = NULL;
for (i = 0; i < ARRAY_SIZE(msub->role); i++) {
msc_role = msub->role[i];
if (!msc_role) {
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "No %s\n", msc_role_name(i));
continue;
}
c = msc_role->priv;
if (!c->remote_to) {
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "%s has no remote\n", msc_role_name(i));
continue;
}
if (!e_link_matches_gsup_msg_source_name(c->remote_to, gsup_msg)) {
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG, "%s has remote to mismatching %s\n", msc_role_name(i),
c->remote_to->remote_name);
continue;
}
/* Found a match. */
e = c->remote_to;
break;
}
if (!e) {
LOG_MSUB_CAT(msub, DLGSUP, LOGL_ERROR,
"There is no E link that matches: Rx GSUP %s from %s\n",
osmo_gsup_message_type_name(gsup_msg->message_type),
osmo_quote_str((const char*)gsup_msg->source_name, gsup_msg->source_name_len));
return -EINVAL;
}
LOG_MSUB_CAT(msub, DLGSUP, LOGL_DEBUG,
"Rx GSUP %s from %s %s\n",
osmo_gsup_message_type_name(gsup_msg->message_type),
msc_role_name(c->role),
e_link_name(e));
return osmo_fsm_inst_dispatch(msc_role, MSC_REMOTE_EV_RX_GSUP, (void*)gsup_msg);
}
void msc_a_i_t_gsup_init(struct gsm_network *net)
{
OSMO_ASSERT(net->gcm);
OSMO_ASSERT(net->vlr);
net->gcm->rx_cb[OSMO_GSUP_MESSAGE_CLASS_INTER_MSC] = (struct gsup_client_mux_rx_cb){
.func = msc_a_i_t_gsup_rx,
.data = net,
};
}
int gsup_msg_assign_an_apdu(struct osmo_gsup_message *gsup_msg, struct an_apdu *an_apdu)
{
if (!an_apdu) {
LOGP(DLGSUP, LOGL_ERROR, "Cannot assign NULL AN-APDU\n");
return -EINVAL;
}
gsup_msg->an_apdu = (struct osmo_gsup_an_apdu){
.access_network_proto = an_apdu->an_proto,
};
if (an_apdu->msg) {
gsup_msg->an_apdu.data = msgb_l2(an_apdu->msg);
gsup_msg->an_apdu.data_len = msgb_l2len(an_apdu->msg);
if (!gsup_msg->an_apdu.data || !gsup_msg->an_apdu.data_len) {
LOGP(DLGSUP, LOGL_ERROR, "Cannot assign AN-APDU without msg->l2 to GSUP message: %s\n",
msgb_hexdump(an_apdu->msg));
return -EINVAL;
}
}
/* We are composing a struct osmo_gsup_msg from the osmo-msc internal struct an_apdu. The an_apdu may contain
* additional info in form of a partly filled an_apdu->e_info. Make sure that data ends up in the resulting full
* osmo_gsup_message. */
if (an_apdu->e_info) {
const struct osmo_gsup_message *s = an_apdu->e_info;
gsup_msg->msisdn_enc = s->msisdn_enc;
gsup_msg->msisdn_enc_len = s->msisdn_enc_len;
if (s->cause_rr_set) {
gsup_msg->cause_rr = s->cause_rr;
gsup_msg->cause_rr_set = true;
}
if (s->cause_bssap_set) {
gsup_msg->cause_bssap = s->cause_bssap;
gsup_msg->cause_bssap_set = true;
}
if (s->cause_sm)
gsup_msg->cause_sm = s->cause_sm;
}
return 0;
}
/* Allocate a new msgb to contain the gsup_msg->an_apdu's data as l2h.
* The msgb will have sufficient headroom to be passed down a RAN peer's SCCP user SAP. */
struct msgb *gsup_msg_to_msgb(const struct osmo_gsup_message *gsup_msg)
{
struct msgb *pdu;
const uint8_t *pdu_data = gsup_msg->an_apdu.data;
uint8_t pdu_len = gsup_msg->an_apdu.data_len;
if (!pdu_data || !pdu_len)
return NULL;
/* Strictly speaking this is not limited to BSSMAP, but why not just use those sizes. */
pdu = msgb_alloc_headroom(BSSMAP_MSG_SIZE, BSSMAP_MSG_HEADROOM, "AN-APDU from gsup_msg");
pdu->l2h = msgb_put(pdu, pdu_len);
memcpy(pdu->l2h, pdu_data, pdu_len);
return pdu;
}
/* Compose a struct an_apdu from the data found in gsup_msg. gsup_msg_to_msgb() is used to wrap the data in a static
* msgb, so the returned an_apdu->msg must be freed if not NULL. */
void gsup_msg_to_an_apdu(struct an_apdu *an_apdu, const struct osmo_gsup_message *gsup_msg)
{
*an_apdu = (struct an_apdu){
.an_proto = gsup_msg->an_apdu.access_network_proto,
.msg = gsup_msg_to_msgb(gsup_msg),
.e_info = gsup_msg,
};
}