This enables us to make the VTY completely independent of any
compile-time program-specific information, i.e. one step closer
to using VTY as a shared library from multiple programs.
Using "end" you can always return to the "enable" level, and from
there the "show" commands are available. So no more need for
exit/exit/exit/exit/disable.
I want to have a shorter lchan summary but with the same
config parameters. Change the current code to be a method
that takes a dump routine as parameter.
Add the rach emergency call allowed (0|1) setting and implement
it by directly manipulating the t2 value. It is the third bit which
is set to 0 when emergency calls are enabled and to one if it is
only enabled for access classes 11 to 15.
Be able to tune the RACH settings of the BTS via the vty interface,
by default they are initialized to -1 which means we will use the
content of the static array (BTS default) and can be changed via
the VTY interface. I have verified the setting on the nanoBTS with
wireshark and I have tested writing the config file.
According to TS 08.18, BVCI=0 is for the SIGNALLING entity,
and BVCI=1 is for the PTM entity. Both should not be used
by the PTP entity that we're configuring here.
Currently vty_interface.c is used for the BSC config, in case of
the MGCP Gateway or the BSC Nat process these logging commands are
not available. Move the commands to a new vty_interface_cmds.c file
to allow to share basic commands across different programs.
The logging/debugging code is generic enough to move it into libosmocore
while keeping OpenBSC specific definitions in openbsc itself.
This commit uses the logging support present in libosmocore-0.1.2,
you will have to update your library to this version.
This new gprs-conf branch is intended to contain everything needed
to configure GPRS in the nanoBTS, but without implementing the SGSN/GGSN
functionality.
The SGSN/GGSN development will happen in a branch based on this branch
called "gprs-sgsn"
This library is intended to collect all generic/common funcitionality
of all Osmocom.org projects, including OpenBSC but also OsmocomBB
The library currently includes the following modules:
bitvec, comp128, gsm_utils, msgb, select, signal, statistics, talloc, timer,
tlv_parse, linuxlist
msgb allocation error debugging had to be temporarily disabled as it depends on
'debug.c' functionality which at the moment remains in OpenBSC
Some NM attributes are defined differently depending on
the BTS type. Having one big nm_att_tlvdef[] table for
all BTS types is no longer sufficient. This patch
* introduces 'struct gsm_bts_model' to describe a BTS model
* adds definitions of gsm_bts_model for BS-11 and nanoBTS
* changes the abis_nm_tlv_parse() function: include a bts pointer
Follow up on 424c4f0e29. As pointed out
by Sylvain on the mailinglist I need to remove this here as well.
Do not call db.c code from code that is located in libbsc.a
vty_interface.c is part of libbsc.a but it started to use code
which is found in db.c recently. Fork the subscriber dumping and
provide more information on the layer3+ (MSC) commands. This
is restoring the separation again.
This is the new logging architecture, including
* support for multiuple logging targets like stderr and vty
* log levels in addition to categories/subsystems
* filtering based on imsi, i.e. only see events for one subscriber
* dynamically change log level for each category for each vty
This has the advantage that counters can be added all over the code
very easily, while having only one routine that stores all of the
current counter values to the database. The counters are synced
every 60 seconds, providing relatively fine grained statistics
about the network usage as time passes by.
Harald Welte
Holger Hans Peter Freyther
Sylvain Munaut